Mariner LX0801PTI/ LX1201PTI/ LX1501PTI IP-65 Touch Monitors USER’S GUIDE www.planar.
The information contained in this document is subject to change without notice. This document contains proprietary information that is protected by copyright. All rights are reserved. No part of this document may be reproduced, translated to another language or stored in a retrieval system, or transmitted by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission. Windows® is a registered trademark of Microsoft, Inc.
Table of Contents Usage Notice Precautions .................................................................................................................................... 5 In a Watercraft or Vehicle ...................................................................................................... 5 Cleaning the Monitor ............................................................................................................. 5 Introduction About the Product ......................................
Addendum A .................................................................................................................................... 24 USB Control of OSD Functions............................................................................................... 24 Addendum B ...................................................................................................................................
Usage Notice ! WARNING – Please do not open or disassemble the product as this may cause electric shock. Doing so will void the warranty. ! ATTENTION – Do not plug the touchscreen in yet! Install the touchscreen driver first! Precautions To maximize the life and safe use of your unit, always be sure to follow the warnings, precautions and maintenance recommendations in this user’s guide.
Introduction About Planar’s Mariner Touch Monitors The LX0801PTI, LX1201PTI and LX1501PTI are high-performance, rugged touch monitors intended for demanding environments, such as those aboard a watercraft. The monitors feature a AMLCD TFT display with IR touchscreen, bright enough to be read in daylight. The monitors include several mounting points for front or rear mounting. The monitors are to be powered directly from circuit breaker protected and switched 8-32 VDC power aboard the watercraft.
1 2 3 Rear View (Descriptions): 1. USB port (Type B) for connecting the touchscreen to the remote computer 2. VGA Signal Input 3. 8-32 VDC Internally Regulated Power Input 4. Modular, removable connector plate for customizing I/O (not available on 12" model at time of print) Mating Connectors (sourced from http://www.ltw-tech.com): USB Cable Assembly: 1 to 5 meter available. LTWWUB-20BFM-A7Axx (01, 02, ...05 for meter length) VGA: The VGA connector located inside the monitor is waterproof.
Features • Brightness control allows you to easily adjust the display to match the ambient light, from full sunlight to night. • The monitor’s TFT display is optically bonded to the Touchscreen to increase contrast ratio. Increased contrast ratio makes it easier to read information displayed on the monitor.
Package Overview The following items are shipped with the display. If any of these items are not in the shipping container, please contact Planar. LX080PTI/ LX1201PTI/ LX1501PTI Quick Start Guide 2M Power Cord Touch Monitor (Bezel is attached for shipping.) Note: Mounting hardware (M4 Screws), mounting brackets, power supply, USB and video cables are sold separately. Software drivers can be downloaded from www.Planar.
Installation Before Installing Keep the following in mind while installing the monitor: • The monitor should be visible to the driver only if it is used for navigation, system control or vehicle information. If the monitor will be used for other purposes, it should be installed in such a way that it will only operate while the watercraft is not moving. • Review all applicable federal, state and local laws and regulations to make sure the monitor is used properly and safely.
Step 1 - Mounting the Monitor The back and sides of the monitor include mounting points that you can use to mount the monitor as your installation requires. Mounting holes on the LX0801PTI, LX1201PTI and LX1501PTI allow the monitor to be mounted : • Front mounted using corner mounting holes • Rear mounted using either VESA or edge mounting holes • Side mounted using variegated bosses 1 2 Mounting from front: 1. 4 corner mounting non-tapped holes in flange (clearance for M4 fastener).
Step 2 - Connecting the Monitor Once the monitor is mounted in place, connect it to the computer (or other video source) and the regulated DC power supply as follows. Planar does not supply a power supply. The monitor is intended to be powered from the watercraft’s DC power system. Power to the monitor (and CPU) is hard switched from the line power that should be protected by a magnetic hydraulic circuit breaker.
Step 3 - IRtouch Software Installation ! IMPORTANT – Do not plug in the touchscreen yet! Install the driver first. 1. Run IRtouch driver setup 2. Accept user agreement 3.
4. Click Install 5. Click continue, you can trust Planar and IRtouch 6. Click on Finish Attach the Planar monitor to the system or install the computer to a docking station. Attach the USB cable. After the USB cable from the monitor is attached to the computer it will recognize the touchscreen for the first time.
7. Continue 8. Click Finish 9. Click the IRtouch icon located on your desktop to calibrate the touch monitor. 10.
11. Set Modes When used in rugged environments with software written for touchscreens, you may find it easier to use the ‘click on release’ radio button. 12. Beep You can set the computer to beep on touch activation if needed.
User Controls Front Panel Controls 3 2 1 CONTROL FUNCTION Auxiliary Power Switch Turns the CPU off and sends signal to host PC through power cable. Brightness Adjust Switches Enables brightness adjustment by depressing one or the other button. Depressing both buttons simultaneously enables auto sync of the monitor to the video source.
Turning the Monitor On and Off The monitor’s power button can control power to the display and CPU. It is not designed to electrically isolate the monitor or CPU from the supply. Use an appropriately sized (4A slow blow 12VDC/2A slow blow 24VDC) magnetic hydraulic circuit breaker to switch line power on/off. Note: Be sure to configure the computer’s power options, including how the computer responds, when the button is pressed. See Windows on-line help for details.
If these optimal cleaners are not available use water or mild glass or window cleaner (that does not contain ammonia) applied to the cloth and not to the display. • Clean the monitor housing with a soft cloth moistened with mild detergent. • Never apply abrasive cleaners, waxes or solvents to the monitor.
Appendix Troubleshooting the Monitor If you are experiencing trouble with the monitor, refer to the following. If the problem persists, please contact your local dealer or our service center. Problem: No image appears on screen • Make sure the brightness is not turned all the way down. • Make sure all data and power cables are properly connected to the monitor and to the computer and power supply. • Make sure the pins on the cables and connectors are not crooked or broken.
Specifications Parameter LX1501PTI - 15" Display Type Full Color TFT AMLCD Display Viewing Area 304 (w) x 228 (h) mm Diagonal Viewing Area 15" (381 mm) Display Color 262 K (6 bit/color); 16.
Parameter LX1201PTI - 12.1" Display Type Full Color TFT AMLCD Display Viewing Area 246 (w) x 184.5 (h) mm Diagonal Viewing Area 12.1" (307 mm) Display Color 262 K (6 bit/color); 16.
Parameter LX0801PTI - 8.4" Display Type Full Color TFT AMLCD Display Viewing Area 170 (w) x 127 (h) mm Diagonal Viewing Area 8.4" (213 mm) Display Color 262 K (6 bit/color); 16.
Addendum A An interconnection to the host PC with USB can be exploited by the customer to create an OSD. Planar has utilized a powerful Pixelworks video IC to enable this functionality should customers desire increased control functions. Planar does not provide the programming to do this. Please consult with Planar’s application engineering team if you have questions about the scale of this undertaking. Contact sales@planar.com. Addendum B Pins 4 and 5 are the switch connections.
Addendum D 325 247 (TOUCH SCREEN OPENING) 262 BRIGHNESS CONTROL 186 (TOUCH SCREEN OPENING) 35 61 75 REMOTE CPU POWER SWITCH (NOT DISPLAY POWER) 142 25 8X M4x0.7 MOUNTING HOLES 7MM MIN THREAD DEPTH 275.0 112 4X M4x0.7 MOUNTING HOLES 7MM MIN THREAD DEPTH 100.0 2X M8.0x1.25 10MM MIN THREAD DEPTH 210.0 FEATURE ALLOWS FOR TILTING AND LOCK DOWN MOUNTING. SEE CAD DATA. 100.0 135.0 75.
Addendum E 392 307 (TOUCH SCREEN OPENING) 317 BRIGHNESS CONTROL 231 (TOUCH SCREEN OPENING) 64 90 104 REMOTE CPU POWER SWITCH (NOT DISPLAY POWER) 171 28 4X M4X0.7 MOUNTING HOLES 5MM MIN THREAD DEPTH 336.0 146 4X M4X0.7 MOUNTING HOLES 5.5MM MIN THREAD DEPTH 100.0 100.
Support and Service Planar is a US company based in Beaverton, Oregon and Espoo, Finland, with a world-wide sales distribution network. Full application engineering support and service are available to make the integration of Planar displays as simple and quick as possible for our customers. RMA Procedure: For a Returned Material Authorization number, please contact Planar Systems, Inc. with the model number(s) and serial number(s).
