LX1200TI Touch Monitor USER’S GUIDE www.planar.
The information contained in this document is subject to change without notice. This document contains proprietary information that is protected by copyright. All rights are reserved. No part of this document may be reproduced, translated to another language or stored in a retrieval system, or transmitted by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission. Windows® is a registered trademark of Microsoft, Inc.
Table of Contents Usage Notice Precautions .................................................................................................................................5 In a Vehicle ..............................................................................................................................5 Cleaning the Monitor ..........................................................................................................5 Introduction About the Product .....................................
Video Specifications ......................................................................................................... 23 Electrical Specifications ................................................................................................... 23 Electromagnetic Compatibility (EMC) ....................................................................... 24 Immunity Characteristics................................................................................................ 24 Safety ...........
Usage Notice ! WARNING – To prevent the risk of fire or shock hazards, do not expose this product to rain or moisture. ! WARNING – Please do not open or disassemble the product as this may cause electric shock. Doing so will void the warranty. ! ATTENTION – Do not plug the touchscreen in yet! Install the touchscreen driver first! Precautions To maximize the life and safe use of your unit, always be sure to follow the warnings, precautions and maintenance recommendations in this user’s guide.
Introduction About Planar’s LX1200TI Touch Monitor The LX1200TI, is a high-performance, rugged touch monitor intended for demanding environments, such as those inside motor vehicles. The monitor features a 12.1-inch diagonal liquid crystal display, with XGA resolution, bright enough to be read in full sunlight. The monitor also includes stereo speakers and a sturdy magnesium enclosure that can withstand shock and vibration.
Front View (Descriptions): 1. 12.1-inch diagonal XGA screen size. 2. Programmable SoftKeys 3. Volume control 4. “All in one” power button - controls power to the remote computer 5. USB port (Type A, accessible from the front) for connecting a peripheral device (a second connection is on the back) 6. Brightness control - allows you to easily adjust the screen to the light condition and to quickly hide the information on the screen (“screen blanking”) 7. Remote PC Shutdown/Start Button 8. Autosync 9.
Bottom View: 4 3 5 2 6 7 1 8 9 10 Bottom View (Descriptions): 1. Brightness control dial 2. USB port (Type A, accessible from the front) for connecting a peripheral device 3. Volume control dial 4. Speaker (on each side) 5. USB port (Type A, accessible from the front) for connecting a peripheral device 6. USB port (Type B) for connecting the touchscreen to the remote computer 7. VGA Signal Input 8. 12 VDC Power Input 9. Power Interrupt Connector 10. Audio Input (3.
Features • The brightness control allows you to easily adjust the display to match the ambient light, from full sunlight to night, even while wearing gloves. Its convenient dial design also enables you to quickly adjust the brightness. • The monitor’s transflective display uses reflected light from the environment - even direct sunlight - to provide a bright image that can be easily viewed under any lighting conditions.
Package Overview The following items are shipped with the display. If any of these items are not in the shipping container, please contact Planar. LX1200 Touch Monitor Power Input Cable Quick Start Guide SoftKey Software and Touchscreen Driver Installation CD Note: Mounting hardware (4 M4 x .7mm Screws), power supply and connecting cables are sold separately.
Installation Before Installing Keep the following in mind while installing the monitor. • The monitor should be visible to the driver only if it is used for navigation, system control or vehicle information. If the monitor will be used for other purposes, it should be installed in such a way that it will only operate while the vehicle is not moving (such as when the parking brake is in use). Review all applicable state and local laws and regulations to make sure the monitor is used properly and safely.
Step 1 - Mounting the Monitor The back of the LX1200TI includes a mounting interface that you can use to mount the monitor on a swing arm or other LCD monitor fixture, as follows. ! IMPORTANT – For optimal results, use the M4 mounting holes around the edges of the monitor. 1. Mount the fixture in its planned location according to the instructions included with the fixture. 2. Attach the monitor to the fixture using the attachments on the back of the monitor, shown in the following diagram.
Step 2 - IRtouch Install Do not plug in the touchscreen yet! Install the driver first. 1. Run IRtouch driver setup from the LX1200TI CD 2. Accept user agreement 3.
4. Click Install 5. Click continue, you can trust Planar and IRtouch 6. Click on Finish Attach the Planar monitor to the system or install the computer to a docking station. After the USB cable from the Planar LX1200TI is attached to the computer it will recognize the touchscreen for the first time.
7. Continue 8. Click Finish 9. Click the IRtouch icon located on your desktop to calibrate the touch monitor. 10.
11. Set Modes When used in rugged environments with software written for touchscreens, you may find it easier to use the ‘click on release’ radio button. 12. Beep You can set the computer to beep on touch activation if needed.
Step 3 - Connecting the Monitor Once the LX1200TI is mounted in place, connect it to the computer (or other video source) and the 12 VDC power supply as follows. Note: This procedure refers to connections to and from the computer. However, depending on your particular hardware configuration, these connections may be to a dock or other device rather than directly to the computer. 1. As needed, route any data and power cables from the computer to the monitor. 2. Make sure the computer is turned off. 3.
Note: If needed, connect an audio cable to the audio port on the monitor, and to the headphone or audio line output connector on the computer. If an external keyboard or other USB device will be used with the monitor, plug it into either of the monitor’s Type A USB connectors. Two USB devices can be connected to the monitor. The following figure shows typical connections. Keyboard (optional) 12V Power Source USB VGA Remote PC Shutdown Audio Computer 5. Turn on power to the computer.
User Controls Front Panel Controls Power Indicator LED Display On/Off Button Softkeys Autosync Power Button Volume Control Remote PC Shutdown/Start Button Brightness/Backlight Control CONTROL FUNCTION Volume Control Dial Increases and decreases the volume of the display Power Button Turns the connected computer on and off - see page 20 for details.
Turning the Monitor On and Off The monitor’s power button controls power to the computer. The monitor itself turns its display on and off according to whether it is receiving a video signal. • To turn on the computer, press the remote PC shutdown/start button on the front of the monitor. The monitor then turns on when it receives a good video signal from the computer (and the monitor’s power indicator turns from red to green). • To turn off the computer, press the remote PC shutdown/start button again.
Cleaning the Monitor Clean the monitor’s touchscreen periodically to keep the display image bright and sharp, and to keep the touchscreen functions working properly. • Always turn off the monitor before cleaning. • Clean the touchscreen only with a dry soft cloth. If this does not clean the screen adequately, use water or mild glass or window cleaner (that does not contain ammonia) applied to the cloth and not to the display. ! CAUTION – Do not apply liquids to the display.
Appendix Troubleshooting the Monitor If you are experiencing trouble with the LX1200TI monitor, refer to the following. If the problem persists, please contact your local dealer or our service center. Problem: No image appears on screen • Make sure the brightness is not turned all the way down. • Make sure all data and power cables are properly connected to the monitor and to the computer and power supply - see page17 for details. • Make sure the pins on the cables and connectors are not crooked or broken.
Specifications Dimensions • Size: 313mm (12.3”) width x 267mm (10.5”) height x 46mm (1.8”) thickness • Screen Size: 12.
Electromagnetic Compatibility (EMC) • ESD, 6 kV contact and 8 kV air discharge • Emissions • • • • • • 47 CFR.
Environmental Specifications Temperature • Operating: -20° to 60° C • Operating Survival: -25° to 65° C • Storage: -20° to +70° C Humidity • Operating: 5 to 90% RH, 40° C, non-condensing • Non-operating: 5 to 93% RH, non-condensing Altitude • Operating: 10,000 ft (IEC 60068 PT2-13, 4 hours) • Non-operating: 15,000 ft (IEC 60068 PT2-13, 4 hours) Vibration • Operating (random): 10 to 500 Hz, 3.
• J5: DC Power Input • Chassis-mounted, two-pin connector (Molex Mini Fit Jr., Header 5569 Molex part number 39-30-0020) • The table below lists the connector’s pin assignments, and the figure below shows the physical layout as seen by the interface cable from the DC power source.
Addendum A Planar Softkey Use The Planar LX1200TI has built in programmable function buttons. This document is to guide the user on the use and installation of the softkey software.
2. Agree to the software license agreement. 3. The software will install a link on your desktop, on the bottom right Windows notification area, and on the start menu. The software will install with a default configuration. 4. There is a screen keyboard that can be activated by right clicking on the Planar Logo in the Windows information tray.
Support and Service Planar is a US company based in Beaverton, Oregon and Espoo, Finland, with a world-wide sales distribution network. Full application engineering support and service are available to make the integration of Planar displays as simple and quick as possible for our customers. RMA Procedure: For a Returned Material Authorization number, please contact Planar Systems, Inc. with the model number(s) and serial number(s).