Contents Preface .........................................................................................2 Installation ...................................................................................4 Unpacking.......................................................................................................................................................................................4 Package Overview ...............................................................................................
Preface This manual is designed to assist users in setting up and using the LCD Monitor. Information in this document has been carefully checked for accuracy; however, no guarantee is given to the correctness of the contents. The information in this document is subject to change without notice. This document contains proprietary information protected by copyright. All rights are reserved.
Important Safety Instructions Please read the following instructions carefully. This manual should be retained for future use. 1. To clean LCD Monitor screen; -- Power off LCD Monitor and unplug the AC Cord. -- Spray a non-solvent cleaning solution onto a rag. -- Gently clean the screen with dampened rag. 2. Do not place the LCD Monitor near a window. Exposing the monitor to rain water, moisture or sunlight can severely damage it. 3. Do not apply pressure to the LCD screen.
Installation Unpacking Before unpacking the LCD Monitor, prepare a suitable workspace for your Monitor and computer. You need a stable and clean surface near a wall power outlet. Make sure that LCD Monitor has enough space around it for sufficient airflow. Though the LCD Monitor uses very little power, some ventilation is needed to ensure that the Monitor does not become too hot.
Viewing Angle Adjustment The LCD Monitor is designed to allow users to have a comfortable viewing angle. The viewing angle can be adjusted from -2°to +90°.(See fig. 1-1) +90° -2° Figure 1-1 Warning Do not force the LCD Monitor over its maximum viewing angle settings as stated above. Attempting this will result in damaging the Monitor and Monitor stand. Detaching LCD Monitor from Its Stand Unscrew screws from the base support column and pull down the hinge to release.
Connecting the AC Power 1. Connect the power cord to the LCD Monitor.(See Fig. 1-5) 2. Connect the power cord to an AC power source. Figure1-5 Connecting the Audio Cable 1. Connect the audio cable to the "LINE OUT" jack on your PC's audio card or to the front panel's “AUDIO OUT” jack of your CD ROM drive. (See Fig. 1-6) Connect the other end of the audio cable to the LCD Monitor's "LINE IN" jack. Figure1-6 Connecting the USB Cable 1. Connect the USB cable to your PC. 2.
Display Controls User Controls A brief description and the location of all LCD Monitor functions controls and indicators: Figure 2-1 1 Power LED will be Green when monitor is on, be yellow when in power saving mode, be dark when monitor in off mode. 2 Power ON/OFF switch. Push to power on or power off.
Adjusting the Monitor's Display Main OSD Main Menu icon Sub Menu item Sub Menu item STANDARD Preset Mode Description Default Setting. Reflects native display capability. MOVIE Displays scenes in clearest detail. Pictures and photographs appear in vibrant colors with sharp detail. GAME Enhances color. TEXT Optimal balance of brightness and contrast prevent eyestrain. The most comfortable way to read onscreen text PHOTO Enhances colors and emphasize fine detail.
FULL Selects wide format for display. Expansion Mode ASPECT Selects 4:3 format for display. Auto adjusts the H/V Position, Phase and Clock of picture. (available in analog mode only) Auto Adjustment H. Position Adjusts the horizontal position. (available in analog mode only) V. Position Adjusts the vertical position. (available in analog mode only) Clock Adjusts picture Clock. (available in analog mode only) Phase Adjusts picture Focus.
Shows the resolution, H/V frequency and input port of current input timing.
OSD Lock Out Function When monitor is in normal display, you can enable the “OSD LOCK OUT” function. Option 1: OSD & Power button lock-all 5 buttons including the “POWER” button are locked. Press and hold the “Auto/Exit” and “ to lock all 5 buttons ”buttons at the same time for 3 seconds The monitor will show an “OSD LOCKED !” message for 5 seconds and the message will disappear automatically. OSD LOCKED ! Repeat this step to unlock.
Technical Information Specifications LCD Panel Size 19W" Display Type Active matrix color TFT LCD Resolution 1440 x 900 Display Dot 1440x (RGB) x 900 Display Color 16.7M with FRC or Dithering Video Input Signal Input Impedance Analog RGB 0.7Vp-p 75 Ohm ± 2% Polarity Positive, Negative Amplitude 0 - 0.7 ± 0.
Power Management Mode Power Consumption* AC Input DPM On 42 W maximum 240 VAC LED Color Green DPM Off 2 W maximum 240 VAC Yellow DC switch off 1 W maximum 240 VAC Dark *Meeting VESA DPM requirements measured from AC Input end of AC power cord. Sync Input Analog Signal Separate TTL compatible horizontal and vertical synchronization.
Standard Timing Table If the selected timing is NOT included in table below, this LCD monitor will use the most suitable available timing. TOTAL/ ACTIVE (DOT / LINE) SYNC WIDTH FRONT BACK PORCH PORCH (DOT / LINE) 16 48 FH (KHz) FV (Hz) SYNC POLARITY 640x350 31.469 + 800 640 96 VGA-350 70.087 – 449 350 2 37 60 TIMING NAME 640x400 31.469 – 800 640 96 16 48 VGA-GRAPH 70.087 + 449 400 2 12 35 640x480 31.469 – 800 640 96 16 48 VGA-480 59.
TOTAL/ ACTIVE (DOT / LINE) SYNC WIDTH FRONT BACK PORCH PORCH (DOT / LINE) FH (KHz) FV (Hz) SYNC POLARITY 1024x768 60.023 + 1312 1024 96 16 176 VESA-768-75Hz 75.029 + 800 768 3 1 28 TIMING NAME 1024x768 60.24 – 1328 1024 96 32 176 1152x864 54.054 + 1480 1152 96 40 192 (60Hz) 59.27 + 912 864 3 13 32 1152x864 63.851 + 1480 1152 96 32 200 (70Hz) 70.012 + 912 864 3 1 44 67.
Troubleshooting This LCD Monitor has been pre-adjusted using factory standard VGA timings. Due to the output timing differences among various VGA cards in the market, users may initially experience an unstable or unclear display whenever a new display mode or new VGA card is selected. Attention This LCD Monitor Supports Multiple VGA Modes. Refer to the Standard Timing Table for a listing of modes supported by this LCD Monitor.
Touch Screen Driver Installation The PJT155R/ PJT175R/ PJT195RW is available with USB connection. The touch software is located on the enclosed CD-ROM for these operating systems: Windows® 7, VISTA, XP, 2000, ME, 98, NT4.0, CE, XP Embedded, Linux, Apple® Mac OS Please Note: The PJT155R/ PJT175R/ PJT195RW is Microsoft® Windows® HID (Human Interface Device) compatible if you use the USB touch screen interface. No additional software driver is required for general operation of the touch screen.
PJT155R/ PJT175R/ PJT195RW Install Instructions If you are using a PC running Windows® 7, VISTA, XP, 2000, ME, 98, NT4.0, follow the instructions below: 1. Power on the PC. 2. Be sure the USB cable is connected from the PC to the LCD display. 3. Download the driver online and execute. 4. Follow the step-by-step instructions as shown on the pop-up windows. If you are using a PC running Windows® XP Embedded, follow the instructions below: Express: 1. Power on the computer. 2.
Product Registration and Technical Support Register Your Planar Products Today Thank you choosing Planar. To assure you receive all the benefits of your Planar product and services, register your Planar product today. Visit our website to register your product at http://www.planar.com/support/product_registration.
Planar Systems,Inc. Customer Service 24x7 Online Technical Support: http://www.planar.com/support 1195 NW Compton Drive Beaverton, OR 97006-1992 Tel: 1-866-PLANAR1 (866-752-6271), or +1 503-748-5799 outside the United States, Hours: 24 hours a day, 7 days a week 2012 Planar Systems, Inc. Planar is a registered trademark of Planar Systems, Inc. Other brands and names are the property of their respective owners. Technical information in this document is subject to change without notice.