Planar UltraRes User Manual TM
Copyright © 6 Jun 2013 by Planar Systems, Inc. All rights reserved. Contents of this publication may not be reproduced in any form without permission of Planar Systems, Inc. Trademark Credits Windows™ is a trademark of Microsoft Corp. Planar's Big Picture™ is a trademark of Planar Systems, Inc. All other names are trademarks or registered trademarks of their respective companies. Disclaimer The information contained in this document is subject to change without notice. Planar Systems, Inc.
Table of Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 European Union Disposal Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table of Contents Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30 Connecting AC Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30 Connecting the Wired IR Module. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table of Contents Remote Monitoring Network Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Remote Monitoring Date and Time. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Remote Monitoring Access Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table of Contents Portrait Wall Mounts - Sides Views . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .95 Optional Pedestal Mount - Front View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .96 Optional Pedestal Mount - Top and Bottom Views. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Introduction Planar UltraRes 4K professional display is a family of 84” Ultra HD displays that produce resolution and picture quality not before seen in large format LCD displays. There are three different offerings: the UR8450-LX, UR8450-MX and the UR8450-3D.
Important Safety Instructions 1 Read these instructions. 2 Keep these instructions. 3 Heed all warnings. 4 Follow all instructions. 5 Do not use any of the Planar UltraRes products near water. 6 Clean the LCD screens with an LCD screen cleaner or LCD wipes. 7 Do not install near any heat sources such as radiators, heat registers, stoves or other apparatus (including amplifiers) that produce heat. 8 Do not defeat the safety purpose of the polarized or grounding type plug.
16 Slight pressure on the LCD will cause distortion of the image. Heavier pressure will cause permanent damage. Planar UltraRes configurations should be mounted where viewers cannot touch the screen or insert small objects in the openings that will create hazards by contacting bare conductive parts. Caution: The front polarizer is soft and subject to scratches from sharp objects. 17 The polarizer is a thin sheet of film laminated to the outside layer of glass on the LCD screen.
European Union Disposal Information English ■ Disposal of old Electrical & Electronic Equipment (Applicable throughout the European Union and other European countries with separate collection programs) Français ■ Mise au rebut des équipements électriques et électroniques usagés (Valable dans l’ensemble de l’Union Européenne ainsi que dans les pays européens disposant de programmes distincts de collecte des déchets) This symbol found on your product or on its packaging, indicates that this product should n
Recommended Usage Recommended Usage In order to get the most out of your LCD modules, use the following recommended guidelines to optimize the display. Burn-In Versus Temporary Image Retention Burn-in causes the screen to retain an image essentially forever, with little or no way to correct the problem. Under normal use, an LCD module will not experience burnin, as plasma displays do, nor will it retain images in any way.
Recommended Usage Normal Use Thermal Guidelines Normal use of the LCD module is defined as operating in the open air to prevent heat buildup, and without direct or indirect heat sources such as lighting fixtures, heating ducts, or direct sunlight that can cause the modules to experience high operating temperatures. If the LCD module will be installed in a recessed area with an LCD surround or enclosure, ensure adequate openings are applied for proper air flow and ventilation.
Basic Concept of Planar UltraRes Display Basic Concept of Planar UltraRes Display The Planar UltraRes display uses four separate outputs that feed into the 84” display as one image. You can use any combination of HDMI, DisplayPort or DVI. There are two main modes of operation for the UltraRes Display: • Single 4K inputs @ 24/25/30Hz • Four-headed input (4K @ 60Hz) Using four separate outputs provides the Ultra HD resolution needed for superior image quality.
Using the Remote Control Using the Remote Control The UltraRes remote control can be used for a variety of functions, including turning the display on and off and assigning individual inputs.
Powering On/Off Planar UltraRes Displays Powering On/Off Planar UltraRes Displays There are several different ways to turn on or off the Planar UltraRes Display: • Using the On/Off buttons on the remote control. See "Using the Remote Control" on page 8 for more information. • Using the Power On/Power Off buttons in the UltraRes Control software tool. See "Using the UltraRes Control Software" on page 43 for detailed information about the UltraRes Control software.
Powering On/Off Planar UltraRes Displays Planar UltraRes in Standby Mode If you are unsure about whether or not the display is on but in standby mode, look for the small Standby LED. If it is off, you will not see the LED. If it is on but in Standby mode, you will see a red LED. As the display starts, the LED blinks until it is on. Once it is on, the LED turns off. Insert IR sensor cord into the IR input on the bottom of the display.
Input Setup Input Setup You can set up your Planar UltraRes display using multiple or single inputs. Both are explained below. You can select multiple or single input mode using the remote control, the UltraRes Control tool or by using RS232 commands. For more information see "Setting Up UltraRes Using Multiple Inputs" on page 32 and "Setting Up UltraRes Using Single Inputs" on page 35. RS232 connector Used to receive signals from the remote control. Used to connect to the Remote Monitoring software.
Input Setup 12 Planar UltraRes User Manual
Installing a Planar UltraRes Display This section explains how to install a Planar UltraRes display. We suggest that you read this entire section before you attempt to install a display. Before You Begin Make sure you have all the items in the following lists before you begin unpacking and installing your display.
Supported Graphics Cards Supported Graphics Cards UltraRes supports a variety of graphics cards from leading manufacturers, such as Nvidia and AMD. In general, you should be looking for graphics cards that have the following features: • Can output 3840 x 2160 at 24 Hz or 30 Hz over a single DisplayPort or HDMI connection. • Four-output graphics cards that can output synchronized (genlocked) 1920 x 1080 outputs at up to 60 Hz. • Each program will have application-specific 3D settings that must be set up.
Supported Graphics Cards Setting Up AMD Graphics Cards For 3D Content Note: If you do not plan to display 3D content, you can skip this section. 1 Right click on the desktop and select Catalyst Control Center. 2 Select AMD FirePro, then select 3D Application Settings. 3 Check the Enable Quad Buffer Stereo box. 4 Select Auto-Stereo (Horizontal Interleaved) from the selection box 5 Click Apply. 6 Open the 3D application and perform application-specific 3D setup.
Recommended PCs Setting Up NVIDIA Graphics Cards 1 Right click on the desktop and select NVIDIA Control Panel. 2 Under 3D Settings, select Manage 3D Settings. 3 Select the Program Settings tab. 4 In section 1, select the program for which its 3D capabilities will be used. If the program is not listed, click Add and search for the program’s .exe file.
Unpacking and Checking Accessories Unpacking and Checking Accessories LCD Module Box The following items are included in the LCD module box. Part Description Number LCD module One per box. 1 LCD mounts (optional) If ordered, this will be inside a separate box inside the LCD box. 1 Picture Note: If you do not use Planar’s mounts, you need to ensure the mounts that you purchase can adequately support the display. Mounting template Used to line up where the wall mounts will be installed.
Unpacking and Checking Accessories Part Description Number Kickstand bracket Mounts to the display when Planar mounts are purchased. 1 M4 x 8 Panhead screws Used to mount the kickstand bracket.
Unpacking and Checking Accessories Accessory Kit The following items are included in the accessory kit. Part Description Number Included AC power cord Power cord. 1 IR sensor Used to receive signals from the remote control. 1 Double-sided tape Used to help in mounting the IR sensor module. 2 USB drive Contains the User Manual and setup software. 1 Passive USB cable Used to set up display software. 1 Remote control Used to power the display on/off, select multiple or single inputs.
Unpacking and Checking Accessories 20 Planar UltraRes User Manual
LCD Installation Before installation, keep the following points in mind: • These displays are heavy. Make sure that you have adequate studs to support the weight of each display if installing on a wall. • The UltraRes must be installed on a flat surface. • If you ordered the optional wall mounts, use the supplied UltraRes mounting template for the center point of the display, as well as for top and bottom bracket installation. • The wall mounts for a landscape and portrait installation look very similar.
Installing an UltraRes Display on a Wall Installing an UltraRes Display on a Wall Caution: For whatever structure is used to mount the display, be sure that it is sufficiently engineered to handle the weight of the display. Also be sure to purchase the correct hardware needed to support the display mounted to that structure. 22 1 Find the center point of the display on the wall where you intend to install it.
Installing an UltraRes Display on a Wall Center notch alignment 3 Use the provided template to determine the center points of the wall mounts. The “V” notches are labeled “L” for a landscape display or “P” for a portrait display. Use the appropriate “V” notch to align with the horizontal line drawn in the previous step.
Installing an UltraRes Display on a Wall 4 In the hole marked “Top” on the template, mark the center of the hole on the wall. Note: If you are installing a landscape display and the template is too long, you can break the template at the notch labeled “P.” 24 5 Let the template hang vertically so it is plumb, as the bottom hole in the template determines where the bottom mount will be installed.
Installing an UltraRes Display on a Wall 8 Line up the middle hole of the top wall mount with the screw hole drilled from the template. Note: This picture shows mounts for a landscape installation. 9 Tighten the screw into the mount. 10 Use a level to make sure the mount is level. 11 Then install additional screws as needed. Note: Screws installed near the mount hooks provide the best support.
Installing an UltraRes Display on a Wall 13 Install the kickstand bracket to the back of the display using four M4 x 8 Panhead screws.
Installing an UltraRes Display on a Wall 14 Using three strong people, carefully hang the back of the display onto the top wall mount bracket using the square brackets on the back of the display. Caution: Be sure these are securely hung, as the top of the wall mount will hold most of the weight of the display.
Installing an UltraRes Display on a Wall 15 On the bottom wall mount, there is locking hardware in the lower corners of the mount. Push the hardware up and finger tighten the captive screws on the bottom to secure the display to the wall.
Installing an UltraRes Display on a Wall Using the Kickstand Bracket The kickstand bracket is used for service mode, without having to remove the display from the wall. Use the following instructions to put the display in service mode. 1 Loosen the captive locking screws on both sides of the bottom mount. 2 Pull the display out and then swing out the kickstand to hold it in place. The kickstand will nest into the kickstand bracket notch.
Connections Connections In order to get your UltraRes display up and running, you need to make three main connections: AC power, the wired IR module and your sources. Connecting AC Power Using the supplied AC power cord, connect one end to a grounded outlet and the other to the AC power input next to the I/O panel the bottom of the UltraRes display.
Connections Connecting Sources The graphics card that you install on your main PC will determine what outputs will be plugged into the Planar UltraRes display. For example, some graphics cards have two HDMI outputs and two DisplayPort outputs. Any combination of these outputs is fine. Below is a visual example of how a basic connection might look.
Connections Setting Up UltraRes Using Multiple Inputs In order to set up the UltraRes using multiple inputs, you must have a computer that contains four video outputs. All four outputs will then be connected to the UltraRes display.
Connections Using UltraRes Control Software to Set Up Multiple Inputs If you use the UltraRes Control software to set up multiple sources, there are three different settings per input channel. Before continuing, make sure you have selected the Multiple Inputs radio button in the lower left corner. • Based on Input Source - This default option automatically selects the same type of input as the current Input Source setting.
Connections Below are two examples of setups in UltraRes Control software that are acceptable. When you are finished, click Update to save your changes.
Connections Setting Up UltraRes Using Single Inputs Instead of having one central device into which you can connect and define your source inputs, single source setup requires connecting from a single-headed source to the display. For example, connecting one input directly from a Blu-ray player into the 84” display.
Connections Selecting Individual Inputs Using the Remote Control The UltraRes remote control has individual inputs that can be selected. For example, if this UltraRes input is connected to HDMI 2, press the HDMI 2 button on the remote control.
Connections Selecting Individual Inputs Using the UltraRes Control Software On the Source tab, select the input that is connected to the UltraRes display. For example, if this UltraRes input is connected to HDMI 2, select the HDMI 2 radio button in the Input Source section on the left.
Connections 38 Planar UltraRes User Manual
Installing the UltraRes Control Software The UltraRes Control software is used as your primary tool for display setup. Use the following instructions to install the UltraRes Control software. 1 Save the UltraRes Control.msi program to your computer’s hard drive. 2 Double click the .msi file to open the installer program.
40 3 Click Next to continue. 4 If you want to save the UltraRes Control files to a different location, click the Browse button and save to the folder of your choice. 5 If you want to see how much space is on your hard drive, click the Disk Cost... button to review storage capacity. 6 Do one of the following: • If you want other users to have access to the UltraRes Control software, select the Everyone radio button.
8 Click Next to continue. 9 As the installation is occurring, you will see the status bar for up to a couple of minutes.
Installing USB Drivers 10 Once the installation is complete, click Close to close the program. Installing USB Drivers When you install the UltraRes Control software, it will automatically install the necessary USB drivers needed for communication between your computer and to the UltraRes display. You only need to complete a few steps to finish the installation process. 42 1 Plug one end of the USB cable into your computer and the other into the UltraRes display.
Installing USB Drivers Using the UltraRes Control Software When you first open the UltraRes Control software, you will see a window similar to the following. Notice that until you connect the inputs to the display, the “Status” at the top of the window will show “Disconnected.” 1 Connect from the PC on which the software is installed to the UltraRes display using a USB connection. 2 Click the Connect button to start the connection process.
Installing USB Drivers 3 The tool will then attempt to auto detect any inputs that are already connected. One of the following will occur: • If an input is detected, the following window appears with information already filled in. Model name Serial number • If no input is auto-detected, you will see a window similar to the following. Notice all fields are grayed out and cannot be changed.
Setting Up Sources 4 If the connection is successful, the “Status” at the top of the window will show “Connected.” Note that all tabs are now accessible and can now be changed if needed. Setting Up Sources This information is covered earlier in the manual. Please see "Setting Up UltraRes Using Multiple Inputs" on page 32 and "Setting Up UltraRes Using Single Inputs" on page 35 for setup information.
Auto Power Off Timer Auto Power Off Timer If there is no incoming source for a certain amount of time and you want to turn power off automatically, use the Auto Power Off Timer slider on the Settings tab and select between 1-60 seconds. Standby Mode This mode allows you to choose between a low power setting, which saves energy, or a “fast startup” mode that keeps the AC power supplies running. Each option is described below.
Changing Backlight Intensity Changing Backlight Intensity To change the brightness of the display, use the Backlight slider on the Display tab. If you want a brighter display, move the slider towards a higher number. If you want to conserve power and increase backlight life, move the slider towards a lower number. Turning Local Dimming On or Off Local Dimming allows the LED edge lighting to dynamically adjust based on the source content.
Upgrading Firmware Upgrading Firmware Upgrading firmware can only be done through the UltraRes Control software using a USB connection. 1 48 Select the File menu bar and then Upgrade Firmware.
Upgrading Firmware 2 A file called 4K.xml will be part of the release package. Navigate to this section and click Open to begin the upgrade process. Note: The upgrade can be initiated from ON or standby mode.
Upgrading Firmware 50 3 The upgrade process will take about 40 minutes. Be sure you are prepared for this amount of time before you initiate the upgrade process. 4 The upgrade process status bar will show where you are in the upgrade process as it proceeds. 5 When the upgrade is complete, you will see a message box similar to the following example.
Error Codes Error Codes To see the last 50 errors that have occurred, select the Error Log tab in the UltraRes Control software, as shown below. For a complete list of the error codes, see "Error Codes in the UltraRes Control Software" on page 102.
Error Codes 52 Planar UltraRes User Manual
DHCP Network Setup Network Settings DHCP Network Setup 1 Turn on the display. 2 Open the UltraRes Control tool and connect to the display. 3 Select the Info tab. The IP address is shown towards the bottom of the tab. 4 One of the following will occur: • If the IP address is 192.168.12.12, then DHCP failed. Use the Static IP Network Setup instructions in the following section.
DHCP Network Setup 5 If the IP address shows anything else, then DHCP succeeded. To confirm the connection, open a Windows command prompt and use the “ping” command with the IP address shown in UltraRes Control. Note: If you cannot confirm a connection, check with your Network Administrator for more information.
Static IP Network Setup Static IP Network Setup If DHCP is unsuccessful, the Remote Monitoring Ethernet interface defaults to a static IP address of 192.168.12.12/24. 1 The PC must be configured to an IP address on the 192.168.12 network. We recommend 192.168.12.100. 2 Assuming the operating system is Windows 7, you can follow these instructions to configure the PC network interface. 3 On the PC, select Start, Control Panel and choose the View by dropdown in the top right corner of the window.
Static IP Network Setup 56 4 Open Network and Sharing Center. 5 Click Change adapter settings in the left side pane. 6 Right-click on the local area connection that corresponds to the network interface that is connected to the UltraRes and then select Properties.
Static IP Network Setup 7 Select Internet Protocol Version 4 (TCP/IPv4) and then click the Properties button.
Static IP Network Setup 58 8 Select the Use the following IP address radio button and then enter 192.168.12.100 for the IP address, 255.255.255.0 for the Subnet mask and 192.168.12.1 for the Default gateway. Click OK to dismiss the IPv4 Properties window. Then click Close to dismiss the Local Area Connection Properties window. 9 To confirm the connection, open a Windows command prompt and enter ping 192.168.12.12, as shown below.
Remote Monitoring Home Planar UltraRes Remote Monitoring Software Planar UltraRes Remote Monitoring is a software tool that displays information about the display via a web browser. It is used primarily for monitoring, reporting and some control (for example, manually powering the displays on and off ). Remote Monitoring Home Launch a web browser. If you are using DHCP, enter in the IP address shown on the Info tab of UltraRes Control. If you are not using DHCP, enter http://192.168.12.
Remote Monitoring Unit Status Remote Monitoring Unit Status The Unit Status page shows a list of the different system settings for the display, including power, signal format and which sources are connected with which inputs. It also shows all current firmware information, the display ID and the serial number of the specific display. Remote Monitoring Display Control The Display Control page contains three sub-pages: Power On/Off, Source Setup and Advanced Setup.
Remote Monitoring Display Control Remote Monitoring Power On/Off Power On/Off buttons control the LED power, not the AC power. You cannot control AC power through Planar UltraRes Remote Monitoring. This section has four options for which you can schedule an automatic power on/off. The options are: • • • • No automatic power on/off Same daily schedule Same Monday-Friday schedule and weekends off Each day has its own schedule. You can only select one of the schedule types.
Remote Monitoring Source Setup Remote Monitoring Source Setup The Source Setup page allows you to perform the same tasks that you can using the UltraRes Control software: • Select single or multiple input mode • Select an input source for each input in single input mode • Select different options for inputs in multiple input mode 62 Planar UltraRes User Manual
Remote Monitoring Advanced Setup Remote Monitoring Advanced Setup The Advanced Setup page allows you to perform many of the same tasks that you can on the UltraRes Control software program. This includes selecting the power mode that works best for your display, either low power or fast startup. You can also select many display settings such as backlight intensity, frame delay, color space definitions and RGB settings.
Remote Monitoring Network Setup Remote Monitoring Network Setup This page allows you to configure network settings and whether or not you use DHCP. For more information about setting up DHCP, see "DHCP Network Setup" on page 53. 64 1 The Hostname box will display Planar as the default. Change this name to something more appropriate for this particular server. The hostname is limited to 16 characters: alphanumeric, dash, or underscore only.
Remote Monitoring Network Setup 4 Under the DHCP section, select the Yes, use DHCP radio button. a Change the default DHCP timeout (ten seconds) only if instructed by your network administrator. b You do not need to fill in anything under the Static (non-DHCP) Network Settings section. However, if you do, these settings will be used in the event that the DHCP attempts to time out. c Go to step 6. 5 Under the DHCP section, select the No, use static settings radio button.
Remote Monitoring Network Setup Remote Monitoring Date and Time Use this page to change date and time information as needed. 1 Set the date and time manually in the box under the Manual Date and Time section. The date format is very exact. Fill in the current date and time using exactly the format shown on the page. Click Set date and time.
Remote Monitoring Network Setup Remote Monitoring Access Control The Access Control page allows you to set parameters needed to access the web, the Remote Monitoring network and RS232 commands. It also allows you to select the correct baud rate.
Remote Monitoring Network Setup Remote Monitoring Software Setup (Upgrading Network Firmware) This page allows you to upload the latest UltraRes Remote Monitoring software. You can also reset all of your settings to the factory defaults, as well as choose the web page link that is associated with the Planar logo in the top right corner of the page. 1 Click Choose File to locate the latest UltraRes software that you downloaded from Planar’s website.
Remote Monitoring Reboot 4 When you click Reset ALL to Factory Default, you receive the Confirm Factory Reset page. Click OK, Reset to Factory Defaults and Reboot if you are sure you want to reset ALL settings to the factory default. 5 The top of each page shows the Planar logo, which is a link to http://www.planar.com. You can change this link to refer to any URL that you find useful by typing it into the Product ID Link box. 6 To make this link live, click Change Product ID Link.
Remote Monitoring Reboot 70 Planar UltraRes User Manual
External Control In addition to using the UltraRes remote control and display, there are other methods of controlling the UltraRes externally: • Using a serial (RS232) link to send ASCII commands and to receive responses to those commands. • Using discrete infrared (IR) codes to program a third-party remote control. • Using SNMP (Simple Network Management Protocol) controls using web browser settings.
RS232 Communication RS232 Communication RS232 control is not necessary for operation, but is a convenient way to control displays from a computer at a distance. If your installation will not use RS232 control, you can skip this section. Most things you can do with the remote, you can do with RS232 commands. Plus, you can send inquiries to the displays and find out the current settings and values. RS232 connections are made with standard straightthrough cables.
RS232 Communication Setting Up Single Inputs Using RS232 Commands You can set up single inputs using RS232 commands. As is typical with using RS232 commands, you can pull up a basic program such as Tera Term to send commands. Below is a short example.
RS232 Commands RS232 Commands The RS232 connection must use the following settings: • • • • • 19200 baud rate 8 data bits 1 stop bit No parity bit No HW (RTS/CTS) or SW (XON/XOFF) flow control RS232 Command Format Commands sent from the initiator to the follower must have the following format: (www:xyz) [CR] Where: • ‘(‘ and ‘)’ indicate the start and end of the command data. If these characters are present, the display processor shall assume that “valid” display data is present in the command string.
RS232 Response Format RS232 Response Format Responses sent from the follower to the initiator shall have the following format: (u;www:x=z) [CR] Where: • ‘(‘ and ‘)’ indicate the start and end of the command data. If these characters are present, the display processor shall assume that “valid” display data is present in the command string. If these characters are not present in the command, the display processor shall assume the data is not valid display data and ignore it.
RS232 Command/Response Examples RS232 Command/Response Examples The following section gives examples of commands and their responses: Example: Power query when unit is powered on Command: (PWR?) [CR] Response: (0;PWR=1) [CR] Example: Set power to 0 (off) Command: (PWR=0) [CR] Response: (0;PWR=0) [CR] Example: Increment brightness from 24 to 25 Command: (BRT+) [CR] Response: (0;BRT=25) [CR] Example: Invalid command code Command: (ZZZ=0) [CR] Response: (1;ZZZ=0) [CR] Example: 76 In
Supported UltraRes RS232 Commands Supported UltraRes RS232 Commands The following section lists the commands that are currently support on the UltraRes display.
Supported UltraRes RS232 Commands Command Code Read/ Write Min Value Max Value String? Information Firmware Version IFV R N/A N/A Yes Information FPGA 1 Version IF1 R N/A N/A Yes Information FPGA 2 Version IF2 R N/A N/A Yes Information FPGA 3 Version IF3 R N/A N/A Yes Information FPGA 4 Version IF4 R N/A N/A Yes Input Mode INM R/W 0 2 No 0 = Single Input 2 = Multiple Inputs Input Source INS R/W 0 15 No 0 = DisplayPort 1 1 = DisplayPort 2 2 = DisplayPort 3 3 =
Supported UltraRes RS232 Commands Command Code Read/ Write Min Value Max Value String? Power PWR R/W 0 1 No 0 = Off 1 = On Remote Key KEY W 0 92 No 1 = On 2 = Off 3 = Menu 4 = Enter 5 = Up 6 = Down 7 = Left 8 = Right 19 = HDMI 1 20 = HDMI 2 21 = HDMI 3 22 = HDMI 4 85 = DisplayPort 1 87 = DisplayPort 2 88 = DisplayPort 3 89 = DisplayPort 4 90 = Single Input 91 = Multiple Inputs 92 = Previous Standby Mode STB R/W 0 1 No 0 = Low Power 1 = Fast Startup Status STA R 0 4 No 0 = St
SNMP Monitoring SNMP Monitoring The current settings and status of UltraRes units can be remotely monitored using SNMP (Simple Network Management Protocol), if the SNMP option is enabled through the web browser settings. The MIB (Management Information Base) used for all Planar display products is available by electronic distribution in the file PLANARDISPLAY-MIB.txt. The table below shows the objects that can be monitored – all Planar SNMP objects are read-only, and no traps are used.
Sending RS232 Commands Via UDP Sending RS232 Commands Via UDP The UDP port 57 accepts the same command sets as RS232. It is convenient for IP control applications and can be tested with a UDP terminal program such as Hercules. Note: Ensure that the Enable ASCII command service (UDP port 57) box is checked on the Access Control page of the UltraRes Control software. Notice the following in the example below: • The IP address is 10.15.0.
Using Discrete IR Codes Using Discrete IR Codes The UltraRes display accepts commands in the form of IR signals that conform to the NEC protocol. Each UltraRes remote control has an NEC control code associated with it. You can use these codes to program a third-party “universal” remote control to work with the UltraRes. These third-party products usually come with a computer software application for this purpose. For more information, consult the documentation provided with the remote control.
Using Discrete IR Codes Supported UltraRes IR Commands Remote Control Button Name Address Data NEC Data From Remote On 1785 1 0x06F901FE HDMI 1 1785 2 0x06F902FD DisplayPort 1 1785 3 0x06F903FC HDMI 2 1785 6 0x06F906F9 DisplayPort 2 1785 7 0x06F907F8 Off 1785 9 0x06F909F6 HDMI 3 1785 10 0x06F90AF5 DisplayPort 3 1785 11 0x06F90BF4 Single Input 1785 13 0x06F90DF2 HMDI 4 1785 14 0x06F90EF1 DisplayPort 4 1785 15 0x06F90FF0 Multiple Inputs 1785 17 0x06F911EE M
Using Discrete IR Codes 84 Planar UltraRes User Manual
Specifications LCD Module Specifications Specification Dimensions UltraRes Display in/lbs mm/kg Width 75.5” 1918.7mm Height 43.7” 1110.7mm Diagonal overall 87.28” 2217mm Depth - without mount 3.05” 77.5mm Depth - with mount 3.17” 80.5mm LCD only 180lbs 82kg Landscape mounts 32lbs 14.
LCD Optical Specifications (Continued) Specification Maximum Viewing Angle 2D content 3D content left/right 3D content up/down Minimum Typical 89° in all directions 89° in all directions 26° combined Color gamut 30° combined 72% NTSC 100% REC709 Red (x,y) Green (x,y) Blue (x,y) White (x,y) 0.645, 0.335 0.300, 0.620 0.150, 0.060 0.279, 0.
Signal Compatibility Signal Compatibility The UltraRes display supports the following video modes. Compatible Video Sources Signal Type PC HDTV UHDTV Resolution Frame Rate (Hz) 960 x 2160 1920 x 2160 1080p 1080p 1080p 1080p 1080p 3840 x 2160 3840 x 2160 3840 x 2160 Line Rate (kHz) Pixel Rate (MHz) 135.000 135.000 27.000 28.125 33.750 56.250 67.500 54.000 56.250 67.500 148.500 297.000 74.250 74.250 74.250 148.500 148.500 297.000 297.000 297.
Signal Compatibility 88 Planar UltraRes User Manual
UltraRes Dimensions Display Dimensions - Front, Side and Top Views Planar UltraRes User Manual 89
Display Dimensions - Rear View Display Dimensions - Rear View ; 0 ; 02817 +2/(6 6(59,&( 3$1(/ /2&.
Display Dimensions - Rear View Rear View - Wall Mount Hangers and Service Panel Locations /$1'6&$3( :$// 02817 +$1*(56 32575$,7 :$// 02817 +$1*(56 6(59,&( 3$1(/ .
Landscape Wall Mounts - Front and Bottom Views Landscape Wall Mounts - Front and Bottom Views 0,1,080 728 ; 3$1(/ +$1*(5 ',63/$< 287/,1( 6(59,&( .,&.67$1' 3$1(/ /2&. 6&5(:6 3$1(/ /2&. 6&5(:6 $& ,1/(7 3$1(/ , 2 .,&.67$1' 6833257 %5$&.(7 Note: Shown from the bottom of the panel.
Landscape Wall Mounts - Sides Views Landscape Wall Mounts - Sides Views 0,1,080 67$1'$5' ,167$// > @ 0,1,080 728&+ ,167$// &(,/,1* / +$1*(5 3/$< 287/,1( :$// Installed position Service position - with kickstand supporting display Planar UltraRes User Manual 93
Portrait Wall Mounts - Front View Portrait Wall Mounts - Front View ; 3$1(/ +$1*(5 ',63/$< 287/,1( , 2 3$1(/ $& ,1/(7 6(59,&( .,&.67$1' 3$1(/ /2&. 6&5(:6 3$1(/ /2&. 6&5(:6 .,&.67$1' 6833257 %5$&.(7 Note: Shown from the bottom of the panel.
Portrait Wall Mounts - Sides Views Portrait Wall Mounts - Sides Views 0,1,080 67$1'$5' ,167$// > @ 0,1,080 728&+ ,167$// &(,/,1* ; 3$1(/ +$1*(5 ',63/$< 287/,1( :$// Installed position Service position - with kickstand supporting display Planar UltraRes User Manual 95
Optional Pedestal Mount - Front View Optional Pedestal Mount - Front View ; 3$1(/ +$1*(5 7<3 ',63/$< 287/,1( 81,7 6(59,&( .,&.67$1' ; 3$1(/ /2&. &/,36 Note: This view shows the pedestal without the display mounted on it.
Optional Pedestal Mount - Top and Bottom Views Optional Pedestal Mount - Top and Bottom Views Note: This view is shown as if looking from above the top of the pedestal. ; 3('(67$/ 02817 +2/(6 &$%/( $&&(66 Note: This view is shown as if looking at the bottom of the pedestal.
Optional Pedestal Mount - Single and Double Sided Optional Pedestal Mount - Single and Double Sided )/86+ 25 0,1 0,1 5($5 75,0 6+((7 6,1*/( 3('(67$/ 21/< 81,7 81,7 81,7 6,1*/( 6,'(' 3('(67$/ ; 5(029$%/( 75,0 )25 7,( '2:1 $1' &$%/( $&&(66 Single sided pedestal with display installed on one side 98 5(029$%/( +2/( 3/8* )25 &$%/( 5287( %27+ 6,'(6 Double sided pedestal with display installed on each side
Optional Pedestal Mount - Double Sided in Service Position Optional Pedestal Mount - Double Sided in Service Position The following drawing shows what the UltraRes display looks like when in service mode on a double sided pedestal.
Optional Pedestal Mount - Double Sided in Service Position 100 Planar UltraRes User Manual
UltraRes LED Codes Troubleshooting During Installation This section includes troubleshooting information about different issues you may encounter during the installation process or after your display has been running for some time. If you are not able to solve your issue in this section, please contact Planar’s Technical Support team for assistance. UltraRes LED Codes The LED on the UltraRes display will show different things, depending on the state of the display.
Error Codes in the UltraRes Control Software Error Codes in the UltraRes Control Software To see the last 50 errors that have occurred, select the Error Log tab in the UltraRes Control software, as shown below. For a complete list of the error codes that may appear in the error log, see the table below. Error Code Meaning Display Behavior and Solution AC Power Supply 1 Failure One of the two AC power supplies is not working properly.
Error Codes in the UltraRes Control Software Error Code Meaning Display Behavior and Solution DC Power Supply Failure One of the DC-DC converters on the main board of the display has failed. The display will not start up if this occurs. Solution: The main board needs to be replaced. FPGA Initialization Failure One of the FPGAs on the main board did not start up correctly. There are two possible causes: one of the FPGAs has corrupt code or is damaged.
Symptoms, Possible Causes and Solutions Symptoms, Possible Causes and Solutions Below are different symptoms that you might encounter as you install your UltraRes display. First look at the different symptoms to see if you can find your issue. And then look at the possible cause and try the suggested solution(s). If you still are not able to resolve your issue, please contact Planar’s Technical Support Department.
Symptoms, Possible Causes and Solutions Symptom: Can’t Get PC to Output 4K @ 60Hz Solution Change the Input Source setting to one of the other quadrant inputs. For example, if you are using HDMI 1-4 and the current Input Source is HDMI 1, change it to HDMI 2. Possible Cause The connector overmold is too large, which can cause the pins not to contact properly on some cards. Solution If using DisplayPort, make sure the connector overmold isn’t too large.
Symptoms, Possible Causes and Solutions Symptom: My Scheduled Network Power On/Off Settings Aren’t Working Possible Cause The Standby Mode setting in the UltraRes Control software may not be set to Fast Startup. If the Standby Mode is not set to Fast Startup, the LAN module power will be disabled in standby. Also, when then scheduler powers off the system, it won’t be able to power back on later if Standby Mode is set to Low Power.
Accessing Planar’s Technical Support Website 1 Go to www.planarpartners.com 2 Once you enter your login and password, you can access downloadable utility software, new firmware, user manuals, and service manuals. Downloading Additional Documentation and Firmware Some of the other documents for the UltraRes 4K professional display, which are or will be available on www.planar.com. Downloading Utility Software 1 Go to www.planarpartners.com. 2 Enter your login and password information.
Downloading Utility Software 108 Planar UltraRes User Manual
Regulatory Information Manufacturer's Name: Manufacturer's Address: Planar Systems, Inc.
110 Planar UltraRes User Manual
Index A AC power connecting, 30 access control in Remote Monitoring, 67 accessories accessory kit contents, 19 checking, 17 checking and unpacking, 17 electronics box contents, 17 LCD module box contents, 17 admin setup in Remote Monitoring, 63 ambient operating temperature, 86 aspect ratio landscape, 85 portrait, 85 auto power off timer, 46 avoiding temporary image retention, 5 B backlight intensity changing, 47 barometric pressure, 86 baud rate, 67 before you begin installing a wall, 13 tools/equipment l
Index F L fast startup power, 46 firmware upgrading, 48 frame delay changing, 47 frame tearing fixing, 47 landscape wall mounts front view, 92 side views, 93 LCD installation, 21 mounts, 17 optical specifications, 85 wipes, 13 LCD module, 17 color gamut, 86 contents in box, 17 dimensions, 85 operating temperature, 86 orientation, 85 screen brightness, 85 specifications, 85 uniformity, 85 viewing angle, 86 local dimming turning on/off, 47 low power standby mode, 46 H humidity, 86 I input setup, 11 inpu
Index power on/off, 61 rebooting the system, 69 Software Setup, 68 Unit Status, 60 resolution of LCD module, 86 RS232 command formats, 74 command/response examples, 76 commands, 74 communication, 72 connecting the cable, 72 response formats, 75 sending commands via UDP, 81 setting up multiple inputs, 72 setting up single inputs, 73 supported UltraRes commands, 77 network setup in Remote Monitoring, 64 normal use thermal guidelines, 6 O operating temperature, 86 LCD module, 86 optical specifications, 85 o
Index sources connecting, 31 setting up in UltraRes Control software, 45 space requirements for installation, 13 specifications environmental, 86 LCD module, 85 LCD optical, 85 mechanical, 85 multiple input compatibility, 87 signal compatibility, 87 standby mode fast startup power, 46 low power, 46 via UltraRes Control, 46 static IP network setup, 55 supported formats for multiple inputs, 32 T temperature operating, 86 requirements for normal use, 6 temporary image retention avoiding, 5 definition, 5 ther
