Thank you for choosing our product! Please read the instructions carefully so you will know how to operate your product properly. If there are any technical questions, please contact: Customer care: (805) 751-4854 & Live chat Online support: www.planetaudio.com/support IMPORTANT Please enter below the Serial No. which is located on the exterior of the product. Retain this information for future reference. Model No. Serial No.
Table of Contents Introduction .........................................................................................................................................................2 Package Contents ..............................................................................................................................................2 Important ...........................................................................................................................................................
Important Read and understand all instructions before you use your product. If you do not follow the instructions in this manual, we are not responsible for any resulting personal injury or damage to property. This will also void the warranty. Important Safety Precautions • Do not open or attempt to repair this product yourself. Dangerous high voltages are present which may result in electric shock.
Panel Controls and Features 11 10 9 8 7 6 5 4 3 2 1 1. Power Terminals GND: Connect to the closest point on the chassis of your vehicle. REM: Connect to the remote output wire of your head unit. No need to make the remote connection if you use high-level input connection and auto power on function is activated. +12V: Connect to the positive terminal of the 12V vehicle battery. 2. Fuse Holder Insert a 25A blade type fuse (ATO) to provide protection of the circuitry.
8. Low Pass Filter (LPF) Use this control to define the frequency range you want the subwoofer to receive. The subwoofer will only receive the frequencies below the one you set to reproduce sound. Tip: If the other speakers of your audio systems are weak on the mid frequencies, set the LPF control relatively high. If the midrange is well covered by the other speakers of your audio system, set the LPF control relatively low to only receive lower frequency signal. 9.
Protection Mode When protection mode triggers, the red LED on the subwoofer turns on and the subwoofer shuts down. One of the following reasons can trigger protection mode: input overload, short circuit and extremely high temperature. When the red LED turns on, take the following measures. • Check the audio system carefully to determine what has caused the protection mode to trigger. • Reset the subwoofer.
Wiring See the section “Installation Precautions” on page 3. For safety, disconnect the negative terminal of the vehicle battery prior to wiring. Use only high quality wires for reliable installation to minimize signal or power loss. Make sure wires are not squeezed or damaged by sharp edges. Use rubber bushings for penetrations. Make sure all the cables are securely connected and bare wires are properly insulated.
Black Gray To metal frame of the vehicle Blue White Red L+ To the speaker wires L- of your head unit R+ R- • Using the supplied high-level input wire harness, fasten the black wire to the metal frame of your vehicle (for signal noise prevention), and connect the other four colored wires to speaker output wires of your head unit. Make sure to observe speaker polarity. • Make sure the speaker wires are securely connected and properly insulated. Run the wires under the vehicle mats for wire protection.
The REM teminal connection is used to automatically turn on or off the subwoofer every time the connected head unit is turned on or off. If your head unit does not have the remote output wire, connect the REM terminal on the subwoofer to the ignition switch wire of your vehicle. In this case, make sure your head unit is also turned on or off with the operation of the ignition switch to avoid noise occurrence 3.
Problem Protection/Red LED lighting up No sound Solution Turn down volume on your source unit to prevent overdriving. Reset the subwoofer by turning it off and on again (see the section “Protection Mode” on page 6 for more details). If the red LED still lights up, the subwoofer is faulty and needs servicing. Check that audio input connection is correctly and securely made. If using low-level input connection, check the RCA cables are correctly and securely plugged.
Specifications Audio Output power ............................................... max. 1000W Driver size.................................................... 10” Speaker impedance..................................... 2.6Ω Total harmonic distortion (THD) ................... <4% Frequency response .................................... 20Hz - 150Hz Signal-to-noise ratio..................................... 68dB Input sensitivity ............................................ 50mV (low level/RCA); 0.
