ECLIPSE USER MANUAL
WARNING! • G L OTHER L A WARNADIHEN D N A E S E H T O T R E S T R IC T LY L IN E S ! Please read and understand all instruction manuals before use. • The Eclipse GEO3.5 is not a toy. PAINTBALL SAFETY RULES MUST BE FOLLOWED AT ALL TIMES. S S A F E T Y IN S T R U C T IO N A N D G U ID E • Always remove all paintballs from the GEO3.5 when not in use on the field of play. • Never point the GEO3.5 at anything you do not intend to shoot.
WARNING! ING THESE AND ALL OTHER WARN A D H E R E S T R IC T LY T O L IN E S ! • Use only professional paintball fields where codes of safety are strictly enforced. • Use compressed air/nitrogen only. Do not use any other compressed gas or pressurised liquid including CO2. • Always follow instructions, warnings and guidelines given with any first stage regulator you use with the GEO3.5. • Use 0.68 inch calibre paintballs only.
CONTENTS USING THE GEO3.5 (06-26) Details on setting up the GEO3.5 and information on the user interface. This section is essential reading for everyone. 06 07 08 09 10 11 12 14 15 16 18 19 20 21 22 23 24 25 26 Factory set-up guide Installing a 9V Battery Switching on the GEO3.5 Switching off the GEO3.5 Firing the GEO3.5 Using the break beam sensor system The GEO3.
37 38 39 40 41 TRIGGER - The trigger parameter SOLENOID - The solenoid power parameter SOUND - The sound parameter TONES - The tones parameter BACKLIGHT - The backlight parameter RED LEVEL - The backlight red level parameter GRN LEVEL - The backlight green level parameter BLU LEVEL - The backlight blue level parameter CONTRAST - The LCD contrast level parameter AUX OUT - The AUX out parameter DBL CLICK - The double clicking parameter AUTO OFF - The auto off parameter TRAINING - The training parameter S
FACTORY SET-UP GUIDE Before using the GEO3.5 it is important to make sure the SL4 inline regulator, solenoid flow restrictor (SFR) and all electronically controlled parameters are set correctly. ANY of these can have a negative effect on the performance of the marker if set incorrectly. FIG 1A _ The steps below will restore the GEO3.5 settings to the factory settings. These settings will give the GEO3.5 a more balanced performance, ideal for most users.
INSTALLING A 9V BATTE RY Ensure that the GEO3.5 is switched off. Lay the marker on a flat surface in front of you with the feed tube furthest away and with the barrel pointing to the right. FIG 2A Use a 5/64” (2mm) hex key to remove the two countersunk screws that hold the rubber grip onto the frame (see figure 2A). Peel the grip to the right to expose the circuit board within the frame.
SWITCHING ON THE GEO3.5 To switch on the GEO3.5 press the button twice in quick succession, referred to elsewhere in this manual as ‘double-clicking’. The GEO3.5 can also be switched on by pushing and holding the button (see figure 3A).1 FIG 3A SWITCHING OFF THE GEO3.5 Press and hold the button (see figure 3A) until the display shows “TURN OFF”. Release the button and re-press it to turn off the GEO3.5. Alternatively double click the button to enter the menu tree then press to turn off the GEO3.5.
USING THE BREMAK BEAM SENSOR SYSTE The Break Beam Sensor System, referred to elsewhere in this manual as ‘BBSS’ is used to detect when a paintball is ready to be fired from the GEO3.5. If no paintball is ready then the BBSS will inhibit the GEO3.5 from firing. This prevents the GEO3.5 from “chopping” paintballs that are not fully loaded into the marker.1 FIG 4A To switch off the BBSS, press and hold the button for 0.5 seconds (see figure 4A).
THE GEO3.5 NSOLE NAVIGATION CO PREVIOUS / RAISE At the rear of the GEO3.5 grip frame you will find the navigation console (see figure 5A) which is used for: • Turning the GEO3.5 on and off using the button. • Scrolling through menus with the buttons. • Selecting parameters to edit using the • Editing parameters using the • Turning the GEO3.5 BBSS on and off using the • Resetting recorded values using the • Controlling the game timer with the and and NEXT / LOWER button. buttons.
INSTALLING A BARREL Every GEO3.5 comes complete with an Eclipse Shaft4 barrel (see page 70). The bore size of the Shaft4 barrel back is engraved on the barrel back just in front of the body threads. FIG 6A To install the Shaft4 barrel, firstly screw the barrel tip and barrel back sections together. The threads on the Shaft4 barrel tip are reverse threaded. To screw the two sections together, with the barrel pointing away from you, turn the barrel tip in a clockwise direction (see figure 6A).
TRIGGER ADJUSTMENT The GEO3.5 provides the user with the option to use either a micro-switch or an OPTO sensor (default OPTO) as the means for detecting trigger pulls. Before you begin to adjust and set your trigger, you must first select the method of trigger detection that you wish to use by entering the main menu and making your selection from the hardware menu (see page 37).
CONTINUED FIG 7D The magnet return strength screw is used to adjust the amount of force with which the trigger is returned to its rest position by the magnet. Turn the screw clockwise to increase the amount of force. Do not turn the screw too far or it will negate the position of the front stop screw. Turn the screw counter-clockwise to reduce the amount of force. Do not turn the screw too far or there may not be enough force to return the trigger (see figure 7D).
ATTACHING A LOADER Using a 5/32” hex key or your fingers, turn the sprocket screw of the clamping feed tube counter-clockwise (see figure 8A). FIG 8A Release the clamping lever on the feed tube (see figure 8B) and test to see if your loader can easily be pushed into the top of the feed tube. If the loader cannot easily be pushed into the feed tube, loosen the sprocket screw of the clamping feed tube a little more by turning it counter-clockwise using a 5/32” hex key or your fingers (see figure 8A).
THE GAS THROUGH PIPE There is no need to unscrew or remove the gas pipe assembly during day to day usage of the marker. Compressed gas is transferred from the frame to the inline regulator via gas pipe assembly (see figure 9A), comprising of a gas pipe section1 A and pipe nut section B . It is essential that this gas pipe assembly is correctly installed before the marker is supplied with compressed gas.
INSTALLING A YSTEM PRE-SET AIR S WARNING! WARNING! WARNING • Make sure the marker is turned off with a barrel blocking device installed and that no paintballs are in the marker or loader before installing an air system. • Compressed air and nitrogen systems can be extremely dangerous if handled or used incorrectly. Check that the gas through pipe assembly is correctly installed before installing a pre-set air system. See page 15 for instructions on installing the gas through pipe assembly.
CONTINUED Every GEO3.5 comes complete with an Eclipse push on purge system (POPS) which provides a direct connection for a pre-set air system. Before screwing an air system into the POPS ensure that the bonnet is disengaged in its forward position (see figure 10A). If the bonnet is engaged, depress the latch button and slide the bonnet forward. FIG 10A Check that the POPS retaining screws are tight. If the POPS can be moved on the frame the screws are too lose. Use a 5/32” hex key to tighten the screws.
VELOCITY ADJUSTMENT When using your GEO3.5, you may wish to change the velocity at which your GEO3.5 is firing. This is done by inserting a 1/8" hex key into the adjuster screw at the bottom of your GEO3.5 inline regulator and adjusting it accordingly (see Figure 11A).
SOLENOID TOR FLOW RESTRIC The following section covers direct adjustment of the solenoid valve which should only be used by users with a sound knowledge of the GEO3.5 firing cycle. Built into the left side of the fame is the solenoid flow restrictor “SFR” (see figure 12A), which controls the exhaust flow from the bolt system through the solenoid valve. By controlling the exhaust flow from the bolt system, the speed of the bolt during the forward stroke can be sped up or slowed down.
UNLOADING THE GEO3.5 Securely attach a barrel blocking device such as the Eclipse Barrel Sock1 (supplied with the GEO3.5) to the marker as shown in Figure 13A. FIG 13A FIG 13B FIG 13C FIG 13D FIG 13E FIG 13G Turn off the GEO3.5 electronics by holding down the button on the back of the frame. When the screen turns off and the marker speaker emits the ‘off’ tone (if the SOUND parameter is enabled), the marker has been turned off (see figure 13B). With the GEO3.5 pointing away from you.
STORAGE AND N TRANSPORTATIO Your Eclipse GEO3.5 must be clear of all paint and propellant during transportation or storage. Make sure the Eclipse GEO3.5 marker is off. Remove the barrel from the marker. Make sure the marker is clean of any paint residue, dirt and moisture. Store your Eclipse GEO3.5 in a clean, cool, dry place. Keep your Eclipse GEO3.5 away from any unauthorized and unsafe users. It may be a good idea to remove the battery when storing your Eclipse GEO3.5 to prevent unauthorized use.
THE USER INTERFACE The GEO3.5 has a simple user interface through which all aspects of its electronic control system can be monitored and adjusted by means of the three push-buttons and graphical LCD which comprise the navigation console. THE RUN SCREEN LAYOUT The root of the user interface is the run screen which is the screen that is displayed most often when the GEO3.5 is on.
THE BBSS INDICATOR The BBSS is able to switch itself off in the event of a blockage or contamination preventing it from functioning correctly. In this instance, the BBSS will switch itself back on once the blockage is cleared and the correct operation can be resumed. The BBSS indicator on the main screen is used to indicate the eight possible states of the BBSS as follows: BBSS Enabled and ball detected The GEO3.5 can be fired at the maximum rate of fire determined by the chosen firing mode.
THE SOUND INDICATOR The sound indicator on the run screen is used to convey if the SOUND parameter in the HARDWARE menu (page 37) is switched on or off. There are two possible conditions that can be indicated: Sound enabled The SOUND parameter is enabled. The GEO3.5 will make sounds when switched on and off and when the game timer alarms or times out. Sound disabled The SOUND parameter is disabled. The GEO3.5 will not make any sounds.
THE LOCK INDICATOR The GEO3.5 has a Tournament Lock which prevents the user from making changes to any parameter that affects the way in which the GEO3.5 shoots, without the need for tools. This feature is necessary in order to make the GEO3.5 legal for tournament play. To enable or disable the tournament lock see Accessing the Menu System on page 27.
THE ACTUAL RATE OF FIRE When the actual ROF is selected for display the run screen will look something like the screen to the right. The value displayed in the top left of the screen represents the number of full cycles completed in a second - the actual rate of fire over that second. THE PEAK RATE OF FIRE When the peak ROF is selected for display the run screen will look something like the screen to the right, which differs from the display of the actual ROF by the inclusion of the indicator ‘PK’.
ACCESSING THE MENU SYSTEM FIG 14A To access the Main menu from the run screen double-click the button and the first item on the Main menu will be displayed. Alternatively, push and hold the button for 2 seconds. A Some of the parameters in the menu system can have a tournament lock applied to them. This lock can be toggled on and off by pressing the tournament lock button on the circuit board (see A in figure 14A).
T H E M E N U SYS T E M The Main menu contains both editable parameters and sub-menus which contain editable parameters. Some of these parameters affect the way the GEO3.5 shoots and are tournament locked as standard from the factory.1 Parameters followed by a * are part of the Smart Menu System and will only be displayed depending on your chosen settings. (e.g. The BS ON ROF parameter will only become available if the ROF CAP parameter is set to on). The Main menu also contains the TURN OFF option.
PRE-SET MENU In order to simplify the set up of the GEO3.5 a number of pre-set configurations are available for selection. Choosing one of these pre-sets will cause all of the necessary parameters to be set in such a way as to make the GEO3.5 comply with the rules governing a particular paintball league1. It is also possible for the user to save up to two pre-set configurations of their own.
FIRE MODE PARAMETER This parameter is used to select the firing mode of the GEO3.5 and has the following choices: > SEMI: This is the default and in this firing mode the GEO3.5 will fire one shot for every trigger pull. > RAMP: In this firing mode, the rate of fire is increased above the rate at which the trigger is pulled once certain criteria have been met. These criteria are set by the parameters on the Ramp Setup menu.1 > CANCEL: Editing is cancelled and the parameter is unchanged.
RAMP SET UP MENU This menu is only available when ramping has been selected with the FIRE Mode parameter and comprises a list of parameters that control the way in which the GEO3.5 ramps, as shown below. TYPE PARAMETER This parameter is used to select the ramping style and has the following choices: > STEP: Step ramping will cause the GEO3.5 to shoot in semi-automatic until a number of trigger pulls, set by SEMI SHOTS, have been made at a minimum pull rate, set by KICK IN.
SEMI SHOTS PARAMETER The parameter sets the number of shots in semi-automatic that are required at the KICK IN rate before ramping will start. The parameter can be set between 3 and 9 pulls in 1 pull increments. KICK IN PARAMETER This parameter sets the minimum rate at which the user has to pull the trigger in order to start ramping. This parameter can be set between 3.3 and 10.0 pulls per second in 0.1 pulls per second increments. SUSTAIN PARAMETER Once the GEO3.
TIMING MENU These parameters all relate to the control of the solenoid valve. DWELL PARAMETER The DWELL parameter sets the amount of time that the solenoid is energized and therefore the amount of gas that is released with each shot of the GEO3.5. Setting this parameter too low will result in low velocity shots and/or excessive shot to shot velocity fluctuations. Setting the parameter too high will simply waste gas and make the GEO3.5 louder. The DWELL can be set between 0.0 and 30.0 milliseconds.
FILTER MENU The parameters on the Filter menu are all used to tune the GEO3.5’s software filters which prevent the GEO3.5 from firing unless all of the necessary conditions are met. The factory default settings will be suitable for most set-ups, however certain loader and trigger set-ups may require modification of one or more of these parameters. DEBOUNCE PARAMETER The DEBOUNCE parameter is used to combat any trigger bounce that might occur in the GEO3.
PULL TM PARAMETER The PULL TM parameter is used to set the minimum amount of time that the trigger must be pulled before it is recognised as a valid trigger pull. This parameter can be set between 3.0 and 20.0 milliseconds in 0.1ms increments. RELEASE TM PARAMETER The RELEASE TM parameter is used to set the minimum amount of time that the trigger must be released before it is recognised as a valid trigger release. This parameter can be set between 3.0 and 25.0 milliseconds in 0.1ms increments.
BASIC TRIGGER FILTER SETUP 95% of trigger bounce problems can be eliminated by utilizing one of the nine fixed DEBOUNCE choices (LEVEL 1-9). In attempting to eliminate trigger bounce it is advisable to try the nine fixed DEBOUNCE choices before attempting any advanced set up of the trigger filters. ADVANCED TRIGGER FILTER SETUP In order to optimize the trigger filters it is necessary to have the PULL PT parameter set as high as possible and the RELEASE PT parameter set as low as possible: 1.
TRIGGER PARAMETER The GEO3.5 is fitted with a dual trigger pull detection system. A non-contact OPTO-Electronic trigger sensor arrangement is used to detect trigger movement whilst a micro-switch is used to provide a more traditional tactile feedback for the trigger. The TRIGGER parameter is used to select which system is used. SOLENOID PARAMETER This parameter controls the amount of power used by the solenoid valve and should normally be left at it’s default ‘LO PWR’ setting.
BACKLIGHT PARAMETER This parameter sets the time that the LCD backlight is illuminated after a push-button is pressed. The parameter can be set between 00:00 and 00:20 (20 seconds). If set to 00:00 then the backlight will not be illuminated. RED LEVEL PARAMETER This parameter sets the percentage of red light in the LCD backlight and can be set between 0% and 100% in 10% increments.
CONTRAST PARAMETER The parameter sets the contrast level of the LCD. This parameter is adjustable between 0 and 30 in increments of 1. AUX OUT PARAMETER This parameter turns on and off the AUX socket on the PCB. The choices available for this parameter are: >OFF: AUX socket switched off. >ON: AUX socket switched on. >CANCEL: Cancel editing and leave the parameter unchanged. DBL CLICK PARAMETER This parameter is used to select where double-clicking the for this parameter are: button can be used.
TRAINING PARAMETER In training mode the GEO3.5 simulates the firing cycle so that the user may practice pulling the trigger without wasting air and making lots of noise. The BBSS is overridden in order to simulate paintballs entering the breech and the beeper indicates when a shot is fired. Training mode is indicated with a ‘T’ in the BBSS indicator. > OFF: Training mode is disabled and the GEO3.5 functions normally. > ON: Training mode is enabled.
GAME TIMER MENU This menu is comprised of parameters that control the operation of the Game Timer. GAME PARAMETER This parameter is used to set the Game Time, the time from which the game timer counts down to zero. This parameter can be set between 00:00 and 60:00 minutes in 10 second increments. The factory default is 07:10 (7 minutes 10 seconds). When the game timer reaches 00:00, GAME OVER will be displayed and the audible alarm will sound continually, provided that the SOUND parameter is set to ‘ON’.
THE BREAK BEAMM SENSOR SYSTE FIG 15A Undo the retaining screw for the Break Beam Eye cover on the left hand side of the GEO3.5 using a 5/64” (2mm) hex key (see figure 15A). Remove the eye cover to expose the back of the Break Beam Sensor unit (see figure 15B). Using a dry cotton bud, carefully remove any debris, paint or moisture from the back of the sensor unit and from inside the eye cover. Lift the Break Beam Sensor unit free from the GEO3.
CONTINUED FIG 15D Remove the rubber detent and using a dry cotton bud clean the detent and its location point in the GEO3.5 body, replacing the detent if it is damaged (see figure 15D). Reinsert the detent back into the GEO3.5 body and place the BBSS back into the designated slot in the body (see figure 15E). Ensure that the sensor is face down in the body i.e. looking into the breech.
THE SL4 INLINSEEMBLY REGULATOR AS FIG 16A FIG 16B FIG 16C FIG 16D Unscrew and remove the gas pipe assembly from the SL4 inline regulator (see figure 16A). See page 15 for more information on removing the gas pipe assembly. Grip the SL4 inline regulator tightly through the rubber sleeve and unscrew the SL4 inline regulator from the GEO3.5 body (see figure 16B). Pull the foregrip crown down to free it from the GEO3.5 body (see figure 16C).
CONTINUED FIG 16I FIG 16J FIG 16K FIG 16L FIG 16M FIG 16N Inspect the internal sealing surfaces of the regulator body, removing any dirt or debris with a cotton bud (see figure 16J). Re-install the adjuster assembly into the inline regulator body threaded end first. Apply light pressure to the top of the adjuster, while using a 1/8” hex turn the adjuster screw counter-clockwise until is stops at the base of the inline regulator body (see figure 16K).
ADVANCED INLININETENANCE REGULATOR MA FIG 17A FIG 17B FIG 17C FIG 17D FIG 17E FIG 17F This procedure is only required if your are fixing a supercharging SL4 inline regulator (common symptoms of supercharging are a very high velocity first shot and/or large variances in shot to shot consistency).
CLEANING THE BODY FILTER FIG 18A Remove the inline regulator as covered on page 44. Turn the GEO3.5 upside down to reveal the body filter inside the body (see figure 18A). Using a 5/64” hex key unscrew and remove the retaining screw (see figure 18B). Then remove the body filter (see figure 18C). Inspect and clean the body filter. If the filter is very dirty replace with a new filter. Insert the filter1 into the FRM on the GEO3.
MAINTAINING THE BOLT SYSTEM FIG 19A FIG 19B FIG 19C FIG 19D The GEO3.5 comes with two bolts. A soft nosed ST3 Bolt and an all metal ST Bolt (see page 72). To install the ST bolt follow the maintenance procedure below, swapping over the bolts. After installation, re-chronograph the GEO3.5 and adjust the SL4 inline regulator accordingly. Push the bolt bonnet up, unlocking the bolt system (see figure 19A). With the bolt bonnet disengaged pull the entire bolt system out of the GEO3.5 body (see figure 19B).
CONTINUED FIG 19I FIG 19J FIG 19K FIG 19L FIG 19M FIG 19N FIG 19O FIG 19P Smear a light coat of Eclipse Grease onto the smooth internal bore of the bolt can from the rear (see figure 19G). Take the prop shaft and having cleaned off any old grease, paint or debris, apply Eclipse Grease to the large rear o-ring (see figure 19H) and also to the 14x2 o-ring near the front of the prop shaft (see figure 19I).
ADVANCED BOLTENANCE SYSTEM MAINT FIG 20A FIG 20B FIG 20C FIG 20D FIG 20E FIG 20F This procedure is only required if you are maintaining the rear section of the prop shaft assembly due to a leak coming from within the bolt bonnet sub assembly or from the front of the bolt. After maintaining the front 14x2 propshaft o-ring and 017 internal can o-ring. Firstly remove the bolt system assembly, then separate the bolt can and prop shaft assemblies as detailed on pages 48-49.
REMOVING THE FRAME FIG 21A FIG 21B FIG 21C FIG 21D Removal of the frame is required for access to the solenoid assembly, trigger bearing carrier assembly and Break Beam Sensor System wires if maintenance on either is required. Disconnect any hosing and unscrew the inline regulator from the Front Regulator Mount (FRM) as detailed in the ‘Cleaning the inline regulator’ section of this Maintenance Guide. Using a 5/64” hex key, remove the four screws that attach the GEO3.5 rubber grips to the GEO3.
ATTACHING THE FRAME FIG 22A FIG 22B FIG 22C FIG 22D FIG 22E FIG 22F FIG 22G FIG 22H To install the frame, firstly check the SFR seal is correctly located in the top of the frame (see figure 22A), then carefully thread the solenoid and the Break Beam Sensor System wiring harnesses through the access hole in the top of the frame and line the frame up so that the rear frame screw sits in the access hole (see figure 22B).
MAINTAINING THE SFR FIG 23A FIG 23B FIG 23C FIG 23D The stages below on SFR maintenance do not require the frame to be removed, and can be followed for SFR removal/ blanking plug installation. Using a small hex key push the SFR body out of the left side of the frame (see figure 23A). Inspect and clean the SFR body and o-rings, making sure the hole through the centre of the SFR body is free of paint or debris (see figure 23B).
THE TRIGGER ASSEMBLY FIG 24A FIG 24B FIG 24C FIG 24D FIG 24E FIG 24F Having removed the frame completely from the GEO3.5 body (see page 51). Unscrew the two M2.5x5 retaining screws which hold the bearing carrier in the frame (see figure 24A). Gently lift the bearing carrier and trigger assembly free from the frame taking care not to damage the micro-switch or the OPTO sensors (see figure 24B). Remove the trigger spring from the bearing carrier, removing any paint or moisture (see figure 24C).
CONTINUED FIG 24G Position the trigger so that the hole through the trigger lines up with the holes in the bearing carrier, slide the trigger pin into place (see figure 24G). Gently lower the trigger assembly and bearing carrier into the frame, taking care not to damage the micro-switch or the OPTO sensor, and ensuring that the trigger is positioned correctly (see figure 24H). Using a 5/64” hex key screw the right side M2.
SOLENOID ASSEMBLY FIG 25A FIG 25B FIG 25C FIG 25D FIG 25E FIG 25F IMPORTANT! The GEO3.5 solenoid assembly contains two sub-assemblies, the solenoid valve and the solenoid manifold. Removal of the solenoid valve is required to access the solenoid manifold for servicing. The solenoid valve itself (see figure 25A) is a non-serviceable item. Any attempt to strip or service the solenoid valve will immediately void the GEO3.5 warranty. If you experience any issue with the GEO3.
CONTINUED Check the underside of the solenoid valve to ensure that it is free from damage or debris (see figure 25F). The solenoid manifold has two gaskets, the top gasket A and the bottom gasket B as illustrated in figure 25G. Carefully remove both gaskets from the solenoid manifold. Inspect and clean the top and bottom gaskets and the solenoid manifold, replacing any damaged components.
CONTINUED FIG 25M FIG 25N FIG 25O FIG 25P FIG 25Q FIG 25R Lastly inspect and clean the large solenoid gasket, replacing if damaged (see figure 25M). Apply a small amount of grease to the outer most groove surrounding the solenoid manifold pocket in the GEO3.5 body. Then making sure the top solenoid manifold gasket lies flat in the solenoid manifold, insert the solenoid manifold back into the GEO3.5 body (see figure 25N).
THE PUSH ON (POPS) PURGE SYSTEM FIG 26A FIG 26B FIG 26C FIG 26D FIG 26E FIG 26F FIG 26G FIG 26H There is no need to remove the POPS from the GEO3.5 frame for general maintenance. IF the POPS is removed, ensure the o-ring is correctly seated before POPS re-attachment. Fully depress the latch button then slide the bonnet forward while continuing to depress latch button (see figure 26A).
CONTINUED FIG 26I FIG 26J FIG 26K FIG 26L FIG 26M FIG 26N FIG 26O FIG 26P Clean and check the condition of the single internal 005 NBR90 o-ring in the front of the POPS insert, replace if necessary (see figure 26I). Lubricate this o-ring liberally using Eclipse Grease. Lubricate the narrow end of the POPS pin with a smear of Eclipse Grease and push the pin, narrow end first, into the POPS insert so that it sits in the POPS insert and pokes through to the front (see figures 26J& 26K).
FAULT FINDING The fault finding guide covers common symptoms, causes and solutions that are likely to be encountered by the average user. If an issue with the GEO3.5 cannot be solved using the fault finding guide, contact your nearest Eclipse Service Centre for assistance. SYMPTOM Although a fresh battery has been fitted, the GEO3.5 will not switch on The battery does not seem to last very long The GEO3.
SYMPTOM POSSIBLE CAUSE The micro-switch is not being activated The micro-switch is damaged The GEO3.5 does not fire The PCB is damaged The solenoid valve is damaged The solenoid valve wires are damaged The GEO3.5 does not cycle fully The GEO3.5 is inconsistent The GEO3.5 is inefficient The GEO3.5 has low rate of fire 6 2 GEO3.
SYMPTOM The GEO3.5 de-gasses very slowly The GEO3.5 leaks from the solenoid assembly GEO3.5 leaks down the barrel Gas vents quickly down the barrel as soon as the GEO3.5 is gassed up The GEO3.
SYMPTOM The GEO3.5 is chopping or trapping paint The GEO3.5 has low velocity on the first shot The GEO3.5 has high velocity on the first shot GEO3.5 has velocity drop-off during rapid fire Constant low velocity 6 4 GEO3.
SYMPTOM POSSIBLE CAUSE SOLUTION GEO3.
E R T N E C E IC V R E S E S IP L C E S Are you unsure of where to send your GEO3.5 to be repaired or serviced? If your local Eclipse dealer can’t assist you, why not contact your nearest certified Eclipse Service Centre and arrange for them to undertake any work that you require. A map listing all of our Service Centres and their contact details can be found in the SUPPORT section of the Planet Eclipse web site at: WWW.PLANETECLIPSE.
OPERATIONAL OVERVIEW FIG 27A Below is a brief overview of what happens when you fire your GEO3.5. The location of parts discussed in the text below can be found on pages 68-69. Assuming the GEO3.5 is gassed up and turned on figure 27A shows the marker in its idle position. The firing chamber is full of compressed air, the prop shaft is pushed back into the back cap by this compressed air. The bolt is held back by the air in the bolt can.
PARTS LIST 01 02 03 05 04 26 08 13 07 31 20 30 19 16 23 28 29 06 27 19 17 09 14 10 11 15 12 18 25 12 24 19 22 21 6 8 GEO3.
PARTS LIST 01 Clamping feed tube assembly 17 Push-button strip 02 Body 18 Display window 03 Bolt assembly 19 PCB screw 04 Rubber detent 20 Navigation console 05 BBSS unit 21 POPS assembly 06 Front frame screw 22 POPS seal 07 Rear frame screw 23 Foregrip crown 08 Solenoid assembly 24 Foregrip sleeve 09 SL4 inline regulator assembly 25 Rubber grip 10 Gas pipe 26 Body plug 11 Pipe nut 27 Body FRM o-ring 12 Gas pipe assembly o-ring 28 Body filter 13 Trigger assem
S H A F T B A R R E L SYS T E M The Eclipse GEO3.5 comes as standard with an Eclipse Shaft4 barrel.1,4 The barrel screws into the body of the GEO3.5 using a right hand thread meaning that if you hold the GEO3.5 pointing away from you the barrel screws into the body in a counter-clockwise direction.
SL4 INLINE REGULATOR 1,2 1 The SL4 inline regulator should be reset to factory after re-assembly. Regulator Piston 2 Only use the SL4 inline regulator with the GEO3.5. 3 Only use the SL4 GEO spring with the GEO3.5 SL4 inline regulator. 4 If the Purge Poppet assembly is removed for maintenance ensure is it re-installed correctly, failure to do so may seriously damage the GEO3.5 solenoid valve.
GEO3.5 BOLT SYSTEM Bolt bonnet Prop shaft Back Cap Plunger Spring Bolt pin 20x2 NBR70 Rear Bumper Plunger 14x2 NBR70 5x1 NBR70 ST3 Bolt Prop shaft 7x1 NBR70 14x2 NBR70 015 NBR90 14x2 NBR70 Prop shaft Tip 22x1 NBR90 ST3 Bolt Tip 020 NBR70 013 NBR70 ST Bolt Retaining ring 017 NBR70 7 2 GEO3.5 M A N UA L 14x2 NBR70 015 NBR90 Bolt can The prop shaft assembly does not need to be fully disassembled for basic maintenance.
SOLENOID ASSEMBLY Solenoid manifold top gasket Poppet cap Solenoid manifold Poppet Solenoid valve gasket Solenoid manifold bottom gasket Solenoid valve1 M2.5x12 Mounting Screws The GEO3.5 solenoid valve is NON-SERVICEABLE. Any attempt to strip, dismantle or service the solenoid valve will immediately void your warranty. For more information on the GEO3.5 solenoid valve please see page 56. G E O3 .
GEO3.5 PUSH ON(POPS) PURGE SYSTEM 005 NBR90 004 NBR70 007 NBR70 Pops body Pin Insert Pops bonnet Push rod 004 NBR70 Pops screw 10-32 UNF x 1” cap head socket Latch spring Latch button 7 4 GEO3.
TRIGGER ASSEMBLY Micro-switch screw (6-32 UNC x1/2” socket set) Bearing carrier screw (M2.
GEO3.5 CIRCUIT BOARD Aux socket Solenoid valve socket Trigger micro switch BBSS socket Trigger OPTO sensors Push - buttons E-portal connector Positive (+) battery terminal Negative (-) battery terminal Tournament lock button LCD display 7 6 GEO3.
COMMON SCREW SIZE CHART SCREW TYPE QTY DESCRIPTION 6 PCB screw (3), bearing carrier screw (2), navigation console (1) (M2.5 X 5 cap head socket) 2 Solenoid screw (2) (M2.
COMMON O-RING SIZE CHART 18x2 POPS Seal 14x2 SL4 Inline regulator piston Propshaft (x2) Bolt external 020 017 016 Bolt can external (x2) Prop shaft back cap Front regulator mount (body) Bolt can internal Shaft4 barrel back (body end) Shaft4 barrel back (tip end) 015 SL4 swivel Bolt bumper (middle) NBR90 013 ST bolt tip 011 SL4 inline regulator adjuster outside Propshaft retaining screw rear 008 SL4 inline regulator adjuster inside 007 Gas transfer pipe POPS insert external 006 Body plug
THE MENU TREE The symbol indicates parameters that are locked when the Tournament Lock is on. See ‘accessing the menu system’ on page 27 for instruction on releasing the Tournament Lock. Parameters followed by a * are part of the Smart Menu System and will only be displayed depending on your chosen settings. (e.g. The BS ON ROF parameter will only become available if the ROF CAP parameter is set to on). MAIN MENU TURN OFF Turn off the GEO3.
CONTINUED RAMP SETUP* (fire mode dependant) TYPE RATE* SEMI SHOTS KICK IN SUSTAIN RESTART BACK STEP (Default) LINEAR CANCEL Step ramping Linear ramping Cancel selection 0 - 100% Percentage linear ramp rate (TYPE dependant). (Default 50%) 3-9 Number of shots before ramping can start. (Default 3) 3.3 - 10.0 pps Rate at which the trigger has to be pulled in pulls per second (pps) before ramping can start. (Default 5pps) 3.3 - 10.
CONTINUED HARDWARE TRIGGER SOLENOID SOUND TONES BACKLIGHT RED LEVEL GRN LEVEL BLU LEVEL CONTRAST AUX OUT AUTO OFF DBL CLICK OPTO (Default) SWITCH CANCEL Use OPTO sensor to detect trigger operation Use micro-switch to detect trigger operation Cancel trigger detection method selection LO PWR (Default) HI PWR CANCEL Select standard solenoid power level Select high power level for solenoid Cancel solenoid power level selection OFF ON (Default) CANCEL Turn off audible indicator Turn on audible indicat
CONTINUED SHOT COUNT GAUGE GAUGE MAX BACK OFF ON (Default) CANCEL Shot gauge off Shot gauge on Cancel selection 100-2000 Shot gauge maximum (reset value) (GAUGE dependant). (Default 140 shots) Return to Main Menu GAME TIMER GAUGE ALARM START BACK 00:00 - 60:00 Countdown game timer start time in minutes. (Default 07:10) 00:00 - 60:00 Alarm activation time in minutes. (Default 01:00) BUTTON (Default) TRIGGER CANCEL Pressing the button starts the Game Timer.
ECLIPSE E-PORTAL The GEO3.5 is compatible with Eclipse E-Portal Software. This software is an upgrade to the GEO3.5 platform. The Eclipse E-Portal Software, USB cable and USB daughter board are sold as a kit, separate from the GEO3.5.1 PC E-Portal allows you to connect the Eclipse GEO3.5 to a PC, where a number of operations can be performed: 2 • Update the marker firmware - from time to time new firmware may be released by Planet Eclipse.
INDEX Actual rate of fire......22, 26 Advanced trigger filter setup......36 Air system......6, 16, 17, 18, 20 ALARM......25, 41, 82 AUTO OFF......39, 81 AUX OUT......22, 23, 39, 81 BACKLIGHT......10, 38, 81 Basic trigger filter set-up......36, 64 Battery......7, 21, 22, 37,61, 64, 69, 76 Battery level indicator......22, 25 BBSS socket......76 Bearing carrier assembly......51, 54, 55, 75 Bearing carrier screw......75, 77 BLU LEVEL......38, 83 Blanking plug.....19,53 Body filter......
Lock indicator......22, 25, 27, 79 Magnet return strength screw......13, 77, 79 Main menu......27, 28, 79 Menu system......26, 28, 79-82 Menu tree......79-82 Micro-switch activation screw......13, 76, 77 MS 10......29, 79 Navigation console......10, 22, 69 NPPL......29, 79 Parameters......10, 26, 27, 28 PCB retaining screw......77 Peak rate of fire......22, 26 Pipe nut.....15, 71, 78 Plastic push-button strip......69 Poppet......14 Poppet cap......14 POPS body......74 POPS bonnet......74 POPS insert......
GET MORE PLANETECLIPSE.COM This product is covered by and / or licensed under one or more of the following patents: G.B. Patents: 2,342,710; 2,345,953; 2,352,022; 2,391,292; 2,391,063. U.S.
