ADE-4200 / ADW-4200 ADSL VPN/Firewall Router User’s Manual
Copyright Copyright (C) 2003 PLANET Technology Corp. All rights reserved. The products and programs described in this User’s Manual are licensed products of PLANET Technology, This User’s Manual contains proprietary information protected by copyright, and this User’s Manual and all accompanying hardware, software, and documentation are copyrighted.
Table of Contents CHAPTER 1. INTRODUCTION .............................................................................................................................. 1 1.1 AN OVERVIEW OF THE ADE-4200/ADW-4200 ................................................................................................. 1 1.2 PACKAGE CONTENTS....................................................................................................................................... 1 1.3 ADE-4200/ADW-4200 FEATURES ...........
3.6.3.5.1 PPTP ....................................................................................................................................................48 3.6.3.5.1.1 PPTP for Remote Access..............................................................................................................48 3.6.3.5.1.2 PPTP for LAN to LAN....................................................................................................................49 3.6.3.5.1.
Chapter 1. Introduction 1.1 An Overview of the ADE-4200/ADW-4200 The ADE-4200 ADSL VPN/Firewall Router and ADW-4200 ADSL Wireless VPN/Firewall Router provide office and residential users the ideal solution for sharing a high-speed ADSL broadband Internet connection on an 11Mbps wireless network or a 10/100Mbps Fast Ethernet backbone. They can support downstream transmission rates of up to 8Mbps and upstream transmission rates of up to 1Mbps.
PLANET ADE-4200/ADW-4200 ADSL VPN/Firewall Router 802.11b access point for extending the communication media to WLAN. Fast Ethernet Switch: A 4-port 10/100Mbps fast Ethernet switch is supported in the LAN site and automatic switching between MDI and MDI-X for 10Base-T and 100BaseTX ports is supported. An Ethernet straight or crossover cable can be used directly, this fast Ethernet switch will detect it automatically.
Chapter 1 Introduction PPP over Ethernet (PPPoE): Provide embedded PPPoE client function to establish a connection. Users can get greater access speed without changing the operation concept, sharing the same ISP account and paying for one access account. No PPPoE client software is required for the local computer. The Always ON, Dial On Demand and auto disconnection (Idle Timer) functions are provided too. Virtual Server: Users can specify some services to be visible from outside users.
PLANET ADE-4200/ADW-4200 ADSL VPN/Firewall Router The ADE-4200 and ADW-4200 VPN connectivity support client-to-VPN gateway and VPN LAN-to-LAN connections. Using these connection capabilities, mobile workers may attach to and access LAN resources from the public Internet while they are working at home or at branches abroad.
Chapter 2. Using the Router 2.1 Cautions for using the ADE-4200/ADW-4200 Do not place the ADE-4200/ADW-4200 under high humidity and high temperature. Do not use the same power source for ADE-4200/ADW-4200 with other equipment. Do not open or repair the case yourself. If the ADE-4200/ADW-4200 is too hot, turn off the power immediately and have a qualified serviceman repair it. Place the ADE-4200/ADW-4200 on a stable surface. Only use the power adapter that comes with the package. 2.
PLANET ADE-4200/ADW-4200 ADSL VPN/Firewall Router ADW-4200 ADSL Wireless VPN / Firewall Router LAN PWR SYS 1 2 3 4 WLAN MAIL PPP ADSL ADW-4200 LED PWR SYS LAN port 1~4 WLAN (ADW-4200 only) MAIL PPP ADSL Meaning Lit when power ON Lit when system is ready Lit when connected to Ethernet device Green for 100Mbps; Orange for 10Mbps Blinking when data transmit/received Lit green when the wireless connection is established. Flashes when sending or receiving data.
Chapter 2 Using ADE-4200/ADW-4200 ADSL Console LAN 1 — 4 (RJ-45 connector) Reset PWR Power Switch 2.4 Cabling Connect the supplied RJ-11 cable to this port when connecting to the ADSL/telephone network. Connect a PS2 or DB9 RS-232 cable to this port when connecting to a PC’s RS-232 port (9-pin serial port). Please note that console cable is not provided on standard package. Connect an UTP Ethernet cable to one of the four LAN ports when connecting to a PC or an office/home network of 10Mbps or 100Mbps.
Chapter 3. Configuration The ADE-4200/ADW-4200 can be configured with your Web browser. The web browser is included as a standard application in the following operation systems, UNIX, Linux, Mac OS, Windows 98/NT/2000/Me, etc. The product provides a very easy and userfriendly interface for configuration. 3.1 Before Configuration This section describes the configuration required by LAN-attached PCs that communicate with the ADE-4200/ADW-4200, either to configure the device, or for network access.
Chapter 3 Configuration 2. Select TCP / IP -> NE2000 Compatible, or the name of any Network Interface Card (NIC) in your PC. 3. Click Properties. 4. Select the IP Address tab. In this page, click the Obtain an IP address automatically radio button.
PLANET ADSL VPN / Firewall Router 5. Then select the DNS Configuration tab. 6. Select the Disable DNS radio button and click “OK” to finish the configuration.
Chapter 3 Configuration 3.3.2 For Windows NT4.0 1. Go to Start / Settings / Control Panel. In the Control Panel, double-click on Network and choose the Protocols tab. 2. Select TCP/IP Protocol and click Properties. 3. Select the Obtain an IP address from a DHCP server radio button and click OK.
PLANET ADSL VPN / Firewall Router 3.3.3 For Windows 2000 1. Go to Start / Settings / Control Panel. In the Control Panel, double-click on Network and Dial-up Connections. 2. Double-click LAN Area Connection. 3. In the LAN Area Connection Status window, click Properties.
Chapter 3 Configuration 4. Select Internet Protocol (TCP/IP) and click Properties. 5. Select the Obtain an IP address automatically and the Obtain DNS server address automatically radio buttons. 6. Click OK to finish the configuration.
PLANET ADSL VPN / Firewall Router 3.3.4 For Windows XP 1. Go to Start / Control Panel (in Classic View). In the Control Panel, double-click on Network Connections. 2. Double-click Local Area Connection 3. In the LAN Area Connection Status window, click Properties.
Chapter 3 Configuration 4. Select Internet Protocol (TCP/IP) and click Properties. 5.
PLANET ADSL VPN / Firewall Router 6. Click OK to finish the configuration. 3.4 Factory Default Settings Before configurating this ADE-4200/ADW-4200, you need to know the following default settings. 1. Web Configurator Username: admin Password : admin 2. Device IP Network settings in LAN site IP Address : 192.168.1.254 Subnet Mask : 255.255.255.0 3. ISP setting in WAN site PPPoE 4. DHCP server DHCP server is enabled. Start IP Address : 192.168.1.100 IP pool counts : 100 3.4.
Chapter 3 Configuration 3.4.2 LAN and WAN Port Addresses The parameters of LAN and WAN ports are pre-set in the factory. The default values are shown below. LAN Port IP address 192.168.1.254 Subnet Mask 255.255.255.0 DHCP server function IP addresses for distribution to PCs Enabled 100 IP addresses continuing from 192.168.1.100 through 192.168.1.199 WAN Port The PPPoE function is enabled to automatically get the WAN port configuration from the ISP, but you have to set the username and password first.
PLANET ADSL VPN / Firewall Router You will get a status report web page when login successfully.
Chapter 3 Configuration n Save Config to FLASH n Logout n Language (provides user interface in English language) Click on the desired item to expand the page in the main navigation pane. 3.6.1 STATUS The Status section provides and contains many items including device H/W and S/W information, LAN, WAN, Port status and all defined interfaces. It also provides useful information for users to review the status of the device.
PLANET ADSL VPN / Firewall Router 3.6.2 Quick Start If you use this device to access the Internet through the ISP, this web page is enough for you to configure this router and access the Internet without a problem. Please check Chapter 3.5 Information from the ISP, then enter the proper values into this web page, click the Apply button and then Save Config to FLASH in the left panel. After the router reboot, you may check the Status web page to check whether the router is connected to the ISP or not.
Chapter 3 Configuration It supports two Ethernet IP addresses in the LAN. With this function, the ADSL router can support two different LAN subnets to access the Internet at the same time. Usually, there is only one subnet in LAN, there is no need to configure a Secondary IP address. The 192.168.1.254 is the default IP address for this ADSL router. The Advanced Options will allow you to configure the routing protocol RIP version 1 or version 2 in receiving and sending direction. 3.6.3.1.
PLANET ADSL VPN / Firewall Router ESSID: Enter the unique ID given to the Access Point (AP), which is already built-in to the wireless broadband firewall gateway. To connect to this device, your wireless clients must have the same ESSID as the device. Regulation Domain: There are five Regulation Domains for you to choose from, including North America (N.America), Europe, France, and Spain. The Channel ID will be different based on this setting. Channel ID: Select the ID channel that you would like to use.
Chapter 3 Configuration Port # Connection Type: Five options to choose from: auto, 10M half-duplex, 10M fullduplex, 100M half-duplex or 100M full-duplex. Sometimes, there are Ethernet compatibility problems with legacy Ethernet devices. You can configure different types to solve the compatibility issues. Port # Rate Limit: When it is enabled, enter a rate value that is configured as multiple of 32kbps. This function limits the inbound and outbound Ethernet throughput around the value that you specified.
PLANET ADSL VPN / Firewall Router 3.6.3.1.4 DHCP Server When you click DHCP Server, you get the following figure. You can disable or enable the DHCP server or enable the DHCP relay functions. If you check Disabled and click Next, then click Apply. The DHCP server function is disabled. Each PC in the LAN should assign a fixed IP address and set the PC’s gateway to the ADSL router.
Chapter 3 Configuration The factory default is rfc 1483-0. If your ISP uses the same access protocol, please click Edit to input other parameters as below. If your ISP does not use rfc 1483-0, you can delete it by clicking Delete. Then you may click Create to create a connection to your ISP to surf the Internet. The following page is then shown. Select one of the access methods among the 5 listed items and click Next to configure the right connection method.
PLANET ADSL VPN / Firewall Router 3.6.3.2.1.1 RFC 1483 routed Description: Give a name for this connection. VPI and VCI: Enter the information provided by your ISP. NAT: The NAT feature allows multiple users to access the Internet through a single IP account, sharing the single IP address. If users in the LAN site have public IP addresses and can access the Internet directly, the NAT function can be disabled. Encapsulation method: Select the protocol format, the default is LlcBridged.
Chapter 3 Configuration Description: Give a name for this connection. VPI and VCI: Enter the information provided by your ISP. Encapsulation method: Select the protocol format, the default is LlcBridged. Select the one provided by your ISP. 3.6.3.2.1.4 PPPoA routed Description: Give a name for this connection. VPI/VCI: Enter the information provided by your ISP. NAT: The NAT feature allows multiple users to access the Internet through a single IP account, sharing the single IP address.
PLANET ADSL VPN / Firewall Router also automatically re-establish the PPPoA session when disconnected by the ISP. ¤ Connect to Demand: if you want to establish a PPPoA session only when there is a packet requesting access to the Internet. User Idle Timeout (in minutes): Auto-disconnect the broadband firewall gateway when there is no activity on the line for a predetermined period of time. Input 0 if you do not want to have idle timeout. 3.6.3.2.1.4 IPoA routed Description: Give a name for this connection.
Chapter 3 Configuration 3.6.3.2.1.5 PPPoE routed Description: Give a name for this connection. VPI/VCI: Enter the information provided by your ISP. NAT: The NAT feature allows multiple users to access the Internet through a single IP account, sharing the single IP address. If users in the LAN site have public IP addresses and can access the Internet directly, the NAT function can be disabled. Username: Enter the username provided by your ISP.
PLANET ADSL VPN / Firewall Router 3.6.3.2.2 DNS The WAN-DNS is shown as below. A Domain Name System (DNS) contains a mapping table for domain name and IP addresses. In the Internet, every host has a unique and friendly name such as www.yahoo.com and an IP address. As the IP Address is hard to remember, the DNS converts the friendly name into its equivalent IP Address. You can obtain a Domain Name System (DNS) IP address automatically if your ISP has provided it when you logon.
Chapter 3 Configuration The router does not have a real time clock on board; instead, it uses the Simple Network Time Protocol (SNTP) to get the current time from the SNTP server from the outside network. Please choose your local time zone, click Enable and click the Apply button. You will get the correct time information after you ready establish a connection to the Internet. If you prefer to enter your own SNTP server, please enter and use it as the first choice.
PLANET ADSL VPN / Firewall Router 3.6.3.3.3 Firmware Upgrade When you click Firmware Upgrade, it allows you to input the location of firmware stored on your PC and click the Upgrade button to upgrade to the new firmware. 3.6.3.3.4 Backup/Restore When you click Backup/Restore, it allows you to save your current settings into a file on your PC. You can click the Backup to store the current settings on a file.
Chapter 3 Configuration factory default settings. 3.6.3.3.6 User Management When you click User Management, you are able to edit existing user’s database or to create other user accessing this device. 3.6.3.4 Firewall This product also serves as an Internet firewall, not only does it provide a natural firewall function (Network Address Translation, NAT), but it also provides rich firewall features to secure a user’s network.
PLANET ADSL VPN / Firewall Router users from accessing the Internet. The functions include: 1. Firewall: prevent access from an outside network, the router provides three levels of security support. l NAT natural firewall: it masks LAN users’ IP addresses which are invisible to outside users on the Internet, making it much more difficult for a hacker to target a machine on your network. This natural firewall is on when NAT function is enabled.
Chapter 3 Configuration Firewall Security: When you enable the Firewall security function, you can select one of the firewall security policies. By default the firewall is set to disabled. Firewall Policy: Select either All blocked/User-defined, High, Medium or Low security level to enable the Firewall. The different among these three security levels is the presetting of port filter rules in the Packet Filter.
PLANET ADSL VPN / Firewall Router 3.6.3.4.2 Packet Filter When you click Packet Filter, you get the following figure. You may configure to filter inbound (incoming) and outbound (outgoing) packets based on port or IP address. If it is based on port, click Port Filters for more options. You may filter the packets based on PORT and packet type (TCP or UDP or any). For example, the protocol number 1 means ICMP. You may enter 1 to protocol number of Raw IP Filtering web page. Port ranges are supported.
Chapter 3 Configuration NEWS(119) RealAudio (7070) PING H.323(1720) T.
PLANET ADSL VPN / Firewall Router 1. Click Packet Filter, you will get the following figure. 2. Click Port Filters, the pre-defined port filter rules screen of low security level is shown as below.
Chapter 3 Configuration 3. 4. Click Delete to delete the HTTP rule. Click Add TCP Filter.
PLANET ADSL VPN / Firewall Router 5. Input the port number and set the inbound & outbound as Allow. 6. The port filter rule of HTTP is shown as below.
Chapter 3 Configuration 7. Configure the Virtual Server to enable the HTTP service in the virtual server setting and input the WEB server’s IP address. If you try to setup a remote management of router permanently, you may enter router’s IP instead. 3.6.3.4.
PLANET ADSL VPN / Firewall Router The Intrusion Detection allows you to prevent your local area network (LAN) from malicious attacks, for example, port scan and Denial-of-Service (DoS). The purpose of such attacks is either to consume the computing resources of your router, or even to bring down the router and network. The Intrusion Detection also supports the blacklisting feature to minimize system overhead that could be consumed in an attack, as well as protecting the network in the meantime.
Chapter 3 Configuration handshaking session per second is reached, the router will consider the SYN flood attack occurs. Maximum Ping Count: set the maximum number of PING packets per second. Once the maximum number of PING per second is reached, the router will assume that an Echo storm attack has occurred Maximum ICMP Count: set the maximum number of ICMP packet per second.
PLANET ADSL VPN / Firewall Router 200.68.76.177 to port 137 (a netbios_ns port). 3.6.3.4.4 MAC Address Filter When you click the MAC Address Filter, you get the following figure. The MAC filtering function enables you to configure your router to block internal users (MAC address) from Internet access. Enable/Disable: to enable or disable MAC Address Filter feature. Allowed/Blocked: To allow or block the following MAC addresses to surf outside network only.
Chapter 3 Configuration MAC Address: There are 10 entries to enter the MAC addresses you want manage. If you select Blocked, the packet with the MAC address in the table will be dropped and others will be forwarded. If you select Allowed, the packet with the MAC address in the table will be forwarded and others will be dropped. Then select the Apply button to save the setting. 3.6.3.4.5 URL Filter When you click the URL Filter, you get the following figure.
PLANET ADSL VPN / Firewall Router Disable All WEB traffic except for Trusted Domain: It allows internal users to access only the specified/trusted domain. Please refer to the Domain Filtering section first, before checking this option. Enable Blocking Log: Check this button to log the corresponding logs into the Event Log under Status. Select the Apply button to save the setting. 3.5.3.4.5.
Chapter 3 Configuration If the router is configured to allow internal users to access only certain specified domains, check add the domain name into the Trusted Domain list. If the router is configured to allow internal users to access all websites except for some forbidden domains, add the forbidden domain name into the Forbidden Domain list. These Forbidden Domains will be blocked, and users will no longer be able to access the websites from the LAN. The checking procedure is like these steps. 1.
PLANET ADSL VPN / Firewall Router transmitting data over a secure VPN tunnel. LAN-to-LAN VPN is an alternative WAN infrastructure that is used to connect offices and home offices to share network resources with each other over a secure VPN tunnel. This router supports two kinds of VPN standards, Point-to-Point Tunneling Protocol (PPTP) and Internet Security Protocol (IPSec). 3.6.3.5.1 PPTP There are two applications provided in PPTP, Remote Access and LAN-to-LAN (please refer below for more information.).
Chapter 3 Configuration Username: If you are a Dial-Out user (client), enter the username provided by your Host. If you are a Dial-In user (server), enter your own username. Password: If you are a Dial-Out user (client), enter the password provided by your Host. If you are a Dial-In user (server), enter your own password. PPP Authentication Type: Default is Auto. Data Encryption: The data can be encrypted by MPPE algorithm. Default is Auto, it is negotiated when establishing a connection.
PLANET ADSL VPN / Firewall Router Netmask: Enter the subnet mask of peer network based on above Peer Network IP setting. Username: If you are a Dial-Out user (client), enter the username provided by your Host. If you are a Dial-In user (server), enter your own username. Password: If you are a Dial-Out user (client), enter the password provided by your Host. If you are a Dial-In user (server), enter your own password. PPP Authentication Type: Default is Auto.
Chapter 3 Configuration Configuring PPTP VPN in the Office The input IP address 192.168.1.200 will be assigned to the remote worker, please make sure this IP is not used in the Office LAN. Configuring PPTP VPN in Remote Side You can configure VPN client with commercial VPN client software package (e.g. SSH) or the Dial-up Adaptor in Windows. Please follow the steps below if you are a Windows 2000 user. 1.
PLANET ADSL VPN / Firewall Router 2. Follow the step and select “Connect to a private network through the Internet” 3.
Chapter 3 Configuration 4. Follow the step, the following screen appears. The setup is completed. 5. To make the connection, click the Virtual Private Connection icon in Dial-up Networking Group, and input the username & password set in ADSL Router.
PLANET ADSL VPN / Firewall Router 3.6.3.5.1.4 An Example of Configuring a Remote Access PPTP VPN Dial-out Connection Background of the Example Corporate establishes a PPTP VPN connection with the file server located in the remote side. The router is installed in the office, connected with a couple of PCs and Servers.
Chapter 3 Configuration Configuring PPTP VPN in the Office You can either input the IP address (69.1.121.33 in this case) or hostname to reach the Server. Refer also to PPTP VPN – remote access (dial-in) for the other parameters.
PLANET ADSL VPN / Firewall Router 3.6.3.5.1.5 An Example of Configuring a LAN-to-LAN PPTP VPN Connection Background of the Example The branch office establishes a PPTP VPN tunnel with the head office to connect two private networks by leveraging the Internet infrastructure. The routers are installed in the head office and branch office accordingly. Application Diagram Configuring PPTP VPN in the Head Office The input IP address 192.168.1.201 will be assigned to the router located in the branch office.
Chapter 3 Configuration Configuring PPTP VPN in the Branch Office The input IP address 69.1.121.3 is the Public IP address of the router located in the head office. If you have a domain name assigned to this IP address - either you registered the DDNS (please refer to the DDNS section), or you have a static IP with a domain name, you can also use the Hostname instead of the IP address to reach the router. Refer also to Configuring PPTP VPN in the Head Office for other parameters.
PLANET ADSL VPN / Firewall Router 3.6.3.5.2 IPSec The router supports IPSec VPN to establish secure, end-to-end private network connections over a public networking infrastructure. The specification is as below: w w w w w w . Encapsulation: tunnel mode . Support IKE authentication method: pre-shared key . Security protocol: ESP and AH . Authentication: MD5, SHA-1 . Encryption: DES, 3DES, AES . Support PFS 3.6.3.5.2.1 IPSec configuration When you click the IPSec, you get the following figure.
Chapter 3 Configuration Connection Name: Give a name for this connection. Local Network: Set the IP address, subnet or address range of the local network. ¤ Single Address: The IP address of the local host. ¤ Subnet: The subnet of the local network. For example, IP: 192.168.1.0 with netmask 255.255.255.0 specifies one class C subnet starting from 192.168.1.1. ¤ IP Range: The IP address range of the local network. For example, IP: 192.168.1.1, end IP: 192.168.1.
PLANET ADSL VPN / Firewall Router ¤ DES: Stands for Data Encryption Standard, it uses 56 bits as an encryption method. ¤ 3DES: Stands for Triple Data Encryption Standard, it uses 168 (56*3) bits as an encryption method. ¤ AES: Stands for Advanced Encryption Standards, it uses 128 bits as an encryption method. Perfect Forward Secrecy: Choose whether to enable PFS using Diffie-Hellman publickey cryptography to change encryption keys during the second phase of VPN negotiation.
Chapter 3 Configuration temporarily disconnected. 3.6.3.5.2.2 An Example of Configuring a LAN-to-LAN IPSec VPN Connection Background of the Example The branch office establishes an IPSec VPN tunnel with the head office to connect two private networks by leveraging the Internet infrastructure. The routers are installed in the head office and branch office accordingly.
PLANET ADSL VPN / Firewall Router Configuring IPSec VPN in the Head Office The local subnet (head office) is set as 192.168.1.0/24 (with netmask 255.255.255.0), while the remote subnet (branch office) is set as 192.168.0.0 (with netmask 255.255.255.0). The IP address 69.1.121.30 in “Secure Gateway Address” field is the Public IP address of the router located in the branch office.
Chapter 3 Configuration 3.6.3.6 Virtual Server In TCP/IP and UDP networks, a port is a 16-bit number, used by the host-to-host protocol to identify to which application program it must deliver incoming messages. Some ports have numbers that are pre-assigned to them by the IANA, and these are known as well-known ports. Servers follow the well-know port assignments so clients can locate them.
PLANET ADSL VPN / Firewall Router 53 69 80 110 119 123 161 443 1503 1720 4000 7070 TCP & UDP UDP TCP TCP TCP UDP TCP TCP & UDP TCP TCP TCP UDP DNS (Domain Name Server) TFTP (Trivial File Transfer Protocol) World Wide Web HTTP POP3 (Post Office Protocol Version 3) NEWS (Network News Transfer Protocol) NTP (Network Time Protocol) SNMP HTTPS T.120 H.323 ICQ RealAudio Being a natural Internet firewall, this network router protects your network from being accessed by outside users.
Chapter 3 Configuration several pre-defined popular application and their port number. Protocol: Select the properly protocol for the application. Port: Input the port number for the application. IP Address: Input the IP address that you want to allow accessing from outside users. DMZ: The DMZ Host is a local computer exposed to the Internet.
PLANET ADSL VPN / Firewall Router 3.6.3.6.2 An example of configuring the Web Server & the Router to be accessible remotely Background of the Example Setup the Web server in the office that can be visible to the outside network. In the meantime, set the router to be accessible remotely through HTTP. Since they use the same protocol (TCP), we have to change the port number of either application to make these two services available.
Chapter 3 Configuration Example 2: Configuring a Virtual Server 1. Set Web server IP address to a fixed IP = 192.168.1.100 2. Set Remote Access as Enable. User can access the router remotely through port 80. 3. Since the port number 80 is used by the router, the Web server port number needs to be changed.
PLANET ADSL VPN / Firewall Router 3.6.3.7 Advanced There are four items under the Advanced section: Routing Table, Dynamic DNS, Checking Email and Device Management. 3.6.3.7.1 Routing Table Click on the Routing Table and then choose Create Router to get the below figure to add a routing table. Destination: Enter the destination subnet IP. Netmask: Subnet mask of destination IP addresses based on above destination subnet IP. Gateway: Enter the gateway IP address which the packet is forwarded to.
Chapter 3 Configuration Interface: Enter the interface which the packet is forwarded to. Cost: This is the same meaning as Hop. Usually, leave it as 1. 3.6.3.7.2 Dynamic DNS Click Dynamic DNS to get the below figure then check the “Enable” button to access the Dynamic DNS service. The Dynamic DNS service allows you to alias a dynamic IP address to a static hostname. This dynamic IP address is the WAN IP address.
PLANET ADSL VPN / Firewall Router Configuring DDNS 1. Set the Web server and FTP server IP address as described in section Virtual Server. 2. Apply an account from this free Web server http://www.dyndns.org/. There are more than 5 DDNS services supported by this router. 3. Configure DDNS as the following. 3.6.3.7.3 Checking Emails Click Checking Emails to get the below figure then check the “Enable” button to access the service. Disable: Check to disable the ADSL router from getting the email.
Chapter 3 Configuration Account Name: Enter the name of the account to which you have the POP access. Normally, it is the text in your email address before the "@" symbol. If you have trouble with it, please contact your ISP. Password: Enter the password of the account POP3 Mail Server: Enter your (POP) mail server name. If you have trouble with it, you would want to contact your ISP or your external mail server's administrator.
PLANET ADSL VPN / Firewall Router router are allowed to logon the device and modify data. ] Expire to auto-logout: Specify a time frame for the system to auto-logout the device. For Example: User A changes HTTP port number to 100, specified it’s own IP address to be 192.168.1.55, and set the logout time to be 50 seconds. Device will only allow User A which IP address is 192.168.1.55 to logon to the Web GUI by typing: 192.168.1.254:100. After 50 seconds, the device will automatically logout User A. 3.6.3.7.
Chapter 3 Configuration 3.6.5 Logout To exit the website, choose Logout to exit completely. Please ensure that you have saved the configuration settings before logout. Be aware that the router is restricted to only one local PC accessing the configuration Web pages. Once a current PC has logged onto the Web pages, other PCs cannot get access except waiting for the current PC to log out of the page. If the previous PC forgets to logout, the second PC can access the page after 3 minutes.
Chapter 4. Troubleshooting If the ADE-4200/ADW-4200 Wireless ADSL Router is not functioning properly, you can refer first to this chapter for simple troubleshooting before contacting your service provider. This could save you time and effort but if the symptoms persist, then consult your service provider. Problems Starting Up the ADE-4200/ADW-4200 Problem None of the LEDs are on when you turn on the ADE-4200/ADW4200 Corrective Action Check the connection between the adapter and the ADE-4200/ADW-4200 .
Appendix A. Specification Product ADSL VPN/Firewall Router ADSL Wireless VPN/Firewall Router Model ADE-4200A / ADE-4200B ADW-4200A / ADW-4200B Hardware Standard ANSI T1.413 Issue 2 ITU G.992.1 (G.dmt) including - Annex A (ADSL over POTS for ADE-3100A/-4100A) - Annex B (ADSL over ISDN for ADE-3100B/ -4100B) G.992.2 (G.
Appendix B. Product Support Most problems can be solved by using the Troubleshooting in Chapter 4. If you cannot resolve the problem with the Troubleshooting Chapter, please contact the dealer where you purchased this product. For any other questions, please contact PLANET directly at the following email address: support@planet.com.tw You can also download upgraded driver or software utilities for free from PLANET’s website at http://www.planet.com.
