Networking & Communication USB ADSL Modem ADU-2000 User’s Manual
Copyright Copyright (C) 2002 PLANET Technology Corp. All rights reserved. The products and programs described in this User’s Manual are licensed products of PLANET Technology, This User’s Manual contains proprietary information protected by copyright, and this User’s Manual and all accompanying hardware, software, and documentation are copyrighted.
Revision User’s Manual for PLANET USB ADSL Modem Model: ADU-2000 Rev: 1.0 (Oct. 2002) Part No.: EM-ADU2000V1.
TABLE OF CONTENTS CHAPTER 1 INTRODUCTION .................................................................................1 FEATURES...............................................................................................................1 DATA REQUIREMENT ................................................................................................1 ADSL LAN mode user ......................................................................................1 ADSL WAN (PPPoE/PPPoA) mode user ............
Chapter 1 Introduction 1 PLANET USB ADSL modem ADU-2000 is designed to provide cost-effective access to high-speed ADSL services. With our ADSL modem, surfing on Internet is just like driving a sport car on the Express Highway. Video on Demand, Videoconference and any high-speed Internet applications is not a dream any more. But a reality! Features l l l l l l l l l l l l l USB bus-powered; an external power supply is not required ANSI T1.413 issue 2, ITU G.dmt(G.992.1), and ITU G.lite(G.992.
System Requirement l l l l Mainboard with USB support Pentium II CPU and above or compatible RAM: 64M or above Windows 98, Windows 2000, Windows ME, Windows XP 2
Chapter 2 Installation 2 Please refer to the following steps to complete ADU-2000 installation. Hardware Installation 1. Turn on your PC 2. Insert the rectangular end of a USB cable into the USB port of your PC. Then, insert the square end of the USB cable into the USB port of the ADU 2000. 3. PC will automatically detect this router as “USB Net Card”. 4. Insert bundled USB driver CD into the proper drive and follow instruction to install ADU 2000. 5. The “Add New Hardware Wizard” will be displayed.
3. Choose CD-ROM drive and Specify a location. Then click Next. 4. Click Next.
5. Click Finish to complete the installation.
Driver Installation for both LAN and WAN mode with Win ME 1. The “Found New Hardware Wizard” will be displayed. Insert ADU-2000 driver CD and click Next. 2. Please specify the path which ADSL modem connected your computer to Internet, then click OK.
3. Click Finish to complete ADU-2000 driver installation. Driver Installation for both LAN and WAN mode with Win 2000 1. The “Add New Hardware Wizard” will be displayed and click Next. 2.
click Next. 3. Select the “CD-ROM drives”, and then click Next. (Make sure you have inserted the driver CD into the CDROM drive.) 4. Windows will find a driver for this device. Then click Next.
5. Windows is installing drivers for your new hardware. 6. The “Digital Signature Not Found” window will pop-up, Click Yes.
7. Click Finish to complete the installation. Driver Installation for both LAN and WAN mode with Win XP 1. The “Add New Hardware Wizard” will be displayed. Choose Install from a list or specific location (Advanced) and click Next.
2. Choose the “Search for the best driver in these locations”, and “Search removable media (floppy, CD_ROM…)”, then click Next. 3.”Conexant AccessRunner USB ADSL Interface” will be displayed and click Next.
3. Under Hardware Installation window. Click “Continue Anyway”. 4. Under Software Installation window. Click ”Continue Anyway” .
5. Completing the Found New Hardware Wizard. Click Finish.
14
Chapter 3 ADSL Configuration 3 ADSL LAN Configuration 1. Conexant Access Runner ADSL icon should be added in the control panel or on the desktop. 2. Click the Conexant Access Runner ADSL icon, it will be displayed the status of the modem.
3. Press Alt + P on the keyboard, the right figure appears. 4. Under the Protocol Setup please set the value of VCI, VPI and Encapsulation. 4. Click My Computer on the desktop\ Control Panel\Network\Configuration -> select TCP/IP -> click properties to configure TCP/IP configuration. 5. IP Address setting: select Specify an address, then enter the value of IP Address and Subnet Mask obtained from ISP.
6. Gateway setting: enter the data from your ISP and click Add. 7. DNS Configuration setting: Select Enable DNS, enter Host name and add DNS Server Search Order. Click Add and OK. 9. Reboot computer to activate the modifications if necessary. NOTE: TCP/IP configuration listed above is a sample for ADU-2000 installation on Windows 98 machine.
user’s manual or consult network administrator to ensure correctness of TCP/IP configuration. Meanwhile, parameters of TCP/IP configuration shall be depended on your ISP; please consult with your service provider about the configuration. ADSL WAN configuration 1. After driver installation, Conexant Access Runner ADSL and AccessRunner DSL icon should be added in the control panel and on the desktop. 2. Click the Conexant Access Runner ADSL icon, it will be displayed the status of the modem. 3.
5. Click the Access Runner DSL icon on the desktop -> enter User name, Password and Phone number (don’t care; recommend “0000”) from your ISP. 6. Click Connect. Now, you can surfer the Internet.
NOTE: TCP/IP configuration listed above is a sample for ADU-2000 installation on Windows 2000 machine. It is strongly recommended to refer user’s manual of operation system or consult network administrator to ensure correctness of TCP/IP configuration. Meanwhile, parameters of TCP/IP configuration shall be depended on your ISP; please consult with your service provider about the configuration.
