CCD Box PoE Internet Camera ICA-700 Quick Installation Guide
Table of Contents 1. Package Contents......................................................................................... 3 2. System Requirements................................................................................... 3 3. Outlook........................................................................................................ 4 4. Physical Installation...................................................................................... 5 5. Setup Tool Installation...................
1. Package Contents ● 1 x ICA-700 ● 1 x Power Adapter ● 1 x Camera Stand ● 1 x CD ● 1 x Quick Installation Guide 2. System Requirements Network Interface 10/100Base-TX Ethernet Monitoring System Recommended for Internet Explorer 6.0 or above System Hardware ● CPU: Pentium 4, 1.
3. Outlook Rear panel of ICA-700 Port Description AUDIO IN An external microphone can be plugged in. AUDIO OUT An external speaker can be plugged in. RESET Reset to manufacturer default valued and reboot. When pressed and held over 10 seconds, the settings of IP Camera will be set to the default values. DC 12V Connect the supplied power adapter. When this device is obtaining power from PoE, you don’t have to attach the power adapter.
LAN (PoE) Connect your Camera to a 10/100Base-TX hub or switch. It is compliant with IEEE 802.3af PoE. Either mid-span PSE or endspan PSE supported. 4. Physical Installation 1. Connect an Ethernet cable Connect one end of an Ethernet cable to the LAN port located on the IP camera’s rear panel and connect the other end to the network device (hub or switch). 2. Attach the external power supply Attach the provided power adapter to the IP camera’s connector labeled “DC 12V” on the rear panel.
5. Setup Tool Installation Initial setup should be performed by using the supplied Windows-based Setup Tool as follows: 1. Insert the bundled product CD into CD-ROM drive to launch the autorun program. 2. When the web page displayed, select and click the “Setup Tool” hyperlink on the menu to start the installation process. Note If the CD’s menu does not appear, click “Start” on the task bar and select “Run” to type “X:\Utility\SetupTool.exe”, assume X is your CD-ROM drive 3.
5. Follow the step for install the Setup Tool, and click “Next” to continue. 6. If you wish to install the Setup Tool in an alternative location, click “Browse” and define a location; otherwise click “Next” to continue. 7. If you wish to install the Setup Tool in an alternative folder of start menu, type a new folder name or select a exiting folder; otherwise click “Next” to continue.
. Check the installation summary, and click “Install” to start the installation. 9. The Setup Tool will be start install to your computer. 10. The Setup Tool installation successful. Click “Finish” to complete the installation. If you would like to run the Setup Tool, please check “Launch Program file” before click Finish button.
6. Setup Tool Configuration This section shows how to perform basic configuration functions by Setup Tool. 1. Double click the icon of Setup Tool on the desktop. 2. The Setup Tool screen will show up as below. It will automatically search and list the IP cameras on your network. 3. Select the IP camera you want, and then click the “Setup” button on the right side. The login window will pop up. If the Administrator User Name and Password have been changed, you will need to enter the new settings.
4. On the following System information screen, it displays the Product Name, Firmware Version and Hardware Version. Click on “Next” to continue. 5. On the following Account settings screen, you can modify the Administrator login user name and password. And you can add some user accounts as Admin, Operator or Viewer. Please click “Next” to continue.
6. On the following Date/Time settings screen, you can adjust the date and time to synchronize with PC, manual setting or synchronize with NTP server. Select the correct Time Zone, then click “Next” to continue. 7. On the following Network settings screen, you can configure the device HTTP port number, IP address, subnet mask, default gateway and DNS. If you are use PPPoE, please select obtain automatically for IP address and DNS settings. Click “Next” to continue.
8. On the following PPPoE settings screen, if you are use PPPoE connection, please select “On” and fill the correct User ID and Password for dialling. Click “Next” to continue. 9. On the following DDNS settings screen, if you have registered the account from the DDNS provider and want to use DDNS function, please select “On” to fill the correct User ID, Password and Hostname for connecting. Click “Next” to continue.
10. In Apply settings screen. Please click “Apply” to finish the configuration, we will suggest you check the “Reboot system to apply new settings” to let the camera work with new settings. Or click “Previous” to check your settings. After modifications, you may now connect the IP camera with the new configuration via web browser. For more information, please refer to the User’s manual.
7. Cam Viewer Lite Installation Note The Cam Viewer Lite / Pro 30 days trial version installation steps are similar. Below is the installation of Cam Viewer Lite. 1. Insert the bundled Cam Viewer CD disk into the CD-ROM drive to launch the autorun program. Once completed, a welcome menu screen will appear. Click the “Cam Viewer Lite” hyperlink, the below InstallShield Wizard dialog box will appear. Note If the welcome screen does not appear, click “Start” at the taskbar.
3. The “Welcome to the InstallShield Wizard for Planet Cam Viewer Lite 1.0.3” will display on the screen, please click “Next”. 4.
5. Please key in user name and company name for which you want and click “Next” to continue installation. 6. Check the option “Complete”, all program features will be installed (Requires the most disk space) and click “Next” to continue installation.
7. “Ready to Install the Program” will appear to prompt you to start the installation. Please click “Install” to start. 8. Please click “No” to finish the Cam Viewer Lite installation. Note In above step, when Cam Viewer works with MBM5 (Motherboard Monitor 5), Cam Viewer will display CPU temperature and fan speed. Please click “Yes” if you need this function and refer to the manual of Cam Viewer CD disk for complete installation.
Appendix A: Feature Listing for Cam Viewer Software Version Cam Viewer Lite Cam Viewer Pro 32 16 / 32 / 64 Dual Monitor - V Smart Guard - V I/O Device V V Hotline - V Address Book - V Unusual event System log Unusual event System log Counting application Counting Application - 2 way counting Remote Playback Server - Unlimited 1 Channel 16 Channels - V General Motion General Motion Missing Object Foreign Object Lose Focus Camera Occlusion 1 Channel 16 Channel IP Camera Inp
Appendix B: Suggest Hardware / System Requirement Total FPS ~600 600~480 480~240 240~120 120~ CPU Intel Core 2 Duo QX6800 Intel Core 2 Duo E6600 Intel Pentium D 930 Intel P4 3.0 Intel P4 2.8 RAM 4 GB 2 GB 2 GB 1 GB 1 GB Chipset of Motherboard Intel 946 or 965 chip, Intel Chipset recommended VGA Card ATI Radeon 9200, nVIDIA GeForce FX-5200, Intel 945/965 or above (ATI recommended) Ethernet 100Base-TX or Above, Gigabit LAN recommended Hard Disk 160 GB or above O.S.
Appendix C: Ordering Information for Cam Viewer Pro Model Description CVP-16 16-Channel Cam Viewer Professional CVP-32 32-Channel Cam Viewer Professional CVP-64 64-Channel Cam Viewer Professional Further configuration and information can be found in the user’s manual CD. Please check the user’s manual for more understanding.
