Datasheet

2
FGSW-1816HPS/FGSW-2624HPS/FGSW-2624HPS4
– PoE port sequence
– PoE schedule
Layer 2 Features
• Prevents packet loss with back pressure (half-duplex) and
IEEE 802.3x pause frame ow control (full-duplex)
• High performance Store and Forward architecture, runt/
CRC ltering eliminates erroneous packets to optimize the
network bandwidth
• Supports VLAN
– Port-based VLAN, up to 18/26 VLAN groups
– IEEE 802.1Q tagged VLAN
– Protocol VLAN
– Provider Bridging (VLAN Q-in-Q) support (IEEE 802.1ad)
– GVRP
– Voice VLAN
• Supports Spanning Tree Protocol
– STP (IEEE 802.1D Spanning Tree Protocol)
– RSTP (IEEE 802.1w Rapid Spanning Tree Protocol)
– MSTP (IEEE 802.1s Multiple Spanning Tree Protocol)
– STP BPDU Filtering, BPDU Protect
• Supports Link Aggregation
– IEEE 802.3ad Link Aggregation Control Protocol (LACP)
– 1 LACP group, up to 2 ports per LACP group
– Cisco ether-channel (static trunk)
– 1 trunk group, up to 2 ports per trunk group
• Provides port mirror (many-to-1)
• Loop detection
Quality of Service
• Ingress/Egress Rate Limit per port bandwidth control
• Storm Control support
– Broadcast/ Multicast /DLF (Destination Lookup Fail)/ARP/
ICMP
• Trafc classication
– IEEE 802.1p Qos/CoS
– TCP/UDP/DSCP/IP precedence of IPv4/IPv6 packets
• Strict priority and Weighted Round Robin (WRR) CoS
policies
Multicast
• Supports IPv4 IGMP snooping v1/ v2 and v3
Solution for IPv6 Networking
With the support for IPv6/IPv4 protocol, and easy and user-friendly management
interfaces, the Managed PoE+ Switch is the ideal choice for IP surveillance, VoIP
and wireless service providers to connect with the IPv6 network. It also helps SMBs
to step in the IPv6 era with the lowest investment and without having to replace the
network facilities even though ISPs establish the IPv6 FTTx edge network.
IPv4 Network
IPv6 Network
Application
IPv6
Stack
IPv4
Stack
Transport Layer
TELNET WEB
SSHSNMP
ICMPACL
DHCPNTP
IPv6 Management HostIPv4 Management Host
FGSW-2624HPS
Built-in Unique PoE Functions for Surveillance Management
As a managed PoE Switch for surveillance network, it features the following
intelligent PoE management functions:
■ PD Alive Check
■ PoE Port Sequence
■ PoE Schedule
Intelligent Powered Device Alive Check
The Managed PoE+ Switch can be congured to monitor a connected PD status in
real time via ping action. Once the PD stops working and it is without response, the
Managed PoE+ Switch will resume the PoE port power and bring the PD back to
work. It will greatly enhance the network reliability through the PoE port resetting the
PD’s power source, thus reducing administrator management burden.
PT PoE Camera
Ping Request
Ping Request
Check alive status at specified times
Restart PoE device if without response
Ping Echo
No Response......
PD Alive!!
Step 1
Step 3
Step 2
Step 4
ON
PoE
ON
ON
PoE
OFF
PD Status
Good!!
Alarm Notification
PoE Port Sequence
To prevent all the PoE ports of the Managed PoE+ Switch from being active at the
same time when the Switch has booted up, the PoE ports of the Managed PoE+
Switch can be configured to allow each port to be activated at an interval time.
In addition, the “Delay” setting is to delay power feeding on each port when the
Managed PoE+ Switch has completely booted up.