(V4) User Manual

- 9 -
- 10 -
- 11 -
- 12 -
4.3 Rear Panel
The rear panel of the 802.3at PoE+ switch comes with a
DC power socket that accepts 55V DC input power and a
grounding terminal that protects the 802.3at PoE+ Switch
against lightning strikes.
55V DC
Figure 4-2: GSD-908HP Switch Rear Panel
 DC Power Receptacle
Power
Notice
1. The device is a power-required device, which
means it will not work till it is powered. If your
networks should be active all the time, please
consider using UPS (Uninterrupted Power Supply)
for your device. It will prevent you from network
data loss or network downtime.
2. In some areas, installing a surge suppression
device may also help to protect your 802.3at
PoE+ Switch from being damaged by
unregulated surge or current to the 802.3at
PoE+ Switch or the power adapter.
Step 4: Connect your 802.3at PoE+ Switch to 802.3af/802.3at
complied powered devices (PD) and other network
devices.
A. Connect one end of a standard network cable to
the 10/100/1000 RJ45 ports on the front panel of
the 802.3at PoE+ Switch.
B. Connect the other end of the cable to the network
devices such as printer servers, workstations,
router, etc.
Note
Connection to the 802.3at PoE+ Switch requires
UTP Category 6/5e/5 network cabling with RJ45
tips
Step 5: Supply power to the 802.3at PoE+ Switch.
A. Connect one end of the power cable to the DC
power adapter and connect its DC plug connector
to the 802.3at PoE+ Switch.
B. Connect the power plug of the power cable to a
standard wall outlet.
When the 802.3at PoE+ Switch receives power, the Power LED
should remain solid amber.
5. Hardware Installation
5.1 Desktop Installation
To install the 802.3at PoE+ Switch on desktop, simply follow
the steps below:
Step 1: Attach the rubber feet to the recessed areas on the
bottom of the PoE+ Ethernet Switch, as shown in
Figure 5-1.
1 2 3 4 5 6 7 8 9-
GSD-90 8HP
PWR
Uplink
PoE-in-Use
ACT
LNK
Default
VLAN
Figure 5-1: Placing the PoE+ Ethernet Switch on the Desktop
Step 2: Place the 802.3at PoE+ Switch on desktop near an AC
power source.
Step 3: Keep enough ventilation space between the 802.3at
PoE+ Switch and the surrounding objects.
Note
When choosing a location, please keep in mind the
environmental restrictions discussed in Section 3
under Specifications.
Customer Support
Thank you for purchasing PLANET products. You can browse
our online FAQ resource on PLANET Web site rst to check if it
could solve your issue. If you need more support information,
please contact PLANET switch support team.
PLANET online FAQs:
https://www.planet.com.tw/en/support/faq
Support team mail address:
[e-mail]
Copyright © PLANET Technology Corp. 2020
Contents are subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp.
All other trademarks belong to their respective owners.
PLANET TECHNOLOGY CORPORATION
e-mail: [e-mail] http://www.planet.com.tw
10F., No.96, Minquan Rd., Xindian Dist., New Taipei City, Taiwan, R.O.C. Tel:[phone] Fax:[phone]
EC Declaration of Conformity
For the following equipment:
*Type of Product: 8-Port 10/100/1000Mbps 802.3at PoE + 1-Port 1000Mbps
Desktop Switch
*Model Number: GSD-908HP
* Produced by:
Manufacturer‘s Name : Planet Technology Corp.
Manufacturer‘s Address: 10F., No.96, Minquan Rd., Xindian Dist.,
New Taipei City 231, Taiwan R.O.C.
is herewith confirmed to comply with the requirements set out in the Council Directive on the
Approximation of the Laws of the Member States relating to Electromagnetic Compatibility
Directive on 2014/30/EU and Low Voltage Directive 2014/35/EU.
For the evaluation regarding the EMC, the following standards were applied:
EN 55032 (2012 + AC:2013)
EN 61000-3-2 (2014)
EN 61000-3-3 (2013)
EN 55024 (2010)
EN60950-1 (2006+A11:2009+A1:2010+A12:2011+A2:2013)
Responsible for marking this declaration if the:
 Manufacturer  Authorized representative established within the EU
Authorized representative established within the EU (if applicable):
Company Name: Planet Technology Corp.
Company Address: 10F., No.96, Minquan Rd., Xindian Dist., New Taipei City 231, Taiwan
R.O.C.
Person responsible for making this declaration
Name, Surname Kent Kang
Position / Title : Director
Taiwan March 25, 2017
Place Date Legal Signature