Z-Wave Wall-mount PIR Motion Sensor HZS-100E / HZS-100A
Z-Wave Wall-mount PIR Mostion Sensor HZS-100E/HZS-100A Copyright Copyright © 2015 by PLANET Technology Corp. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of PLANET.
Z-Wave Wall-mount PIR Mostion Sensor HZS-100E/HZS-100A CE Mark Warning This is a Class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.
Z-Wave Wall-mount PIR Mostion Sensor HZS-100E/HZS-100A Table of Contents Chapter 1. Product Introduction ......................................................................5 1.1 Package Contents...............................................................................5 1.2 Overview.............................................................................................5 1.3 Specifications......................................................................................7 Chapter 2.
Z-Wave Wall-mount PIR Mostion Sensor HZS-100E/HZS-100A Chapter 1. Product Introduction 1.1 Package Contents The package should contain the following: z PIR Sensor x 1 z Quick Installation Guide x 1 z CR123A Lithium Battery x 1 z Accessory Bag x 1 If any of the above items are missing, please contact your seller immediately. 1.
Z-Wave Wall-mount PIR Mostion Sensor HZS-100E/HZS-100A Motion and Temperature Detection PLANET HZS-100 is a Z-Wave wall-mount PIR motion sensor that monitors movement and sends Z-Wave signal when movement is detected. With its built-in temperature sensor feature, the HZS-100 will send the signal out when temperature inside the building changes.. Getting Started is as Easy as 1-2-3 1.
Z-Wave Wall-mount PIR Mostion Sensor HZS-100E/HZS-100A Real-time Alarm Alerts like use of electricity, home alarms and more can be brought to your notice without delays by way of cloud hosting. From now on, you can maintain your home security no matter where you are. 1.
Z-Wave Wall-mount PIR Mostion Sensor HZS-100E/HZS-100A Chapter 2. Hardware Interface Model HZS-100E/HZS-100A Dimensions (W x D x H) 84 x 62 x 50 mm Weight 75g (gross weight) ¾ Front Panel Interface Description PIR Sensor PIR sensor is used to sense motion or detect whether a human has moved in or out of the sensor range. LED When movement is detected, the red LED will flash once. ¾ Rear Program switch Interface Program switch Description Press to include or exclude a Z-Wave network.
Z-Wave Wall-mount PIR Mostion Sensor HZS-100E/HZS-100A Chapter 3. Z-Wave Device Setting 3.1 Configuring Z-Wave Device via HAC-1000 Please refer to the following steps to add Z-Wave device via HAC-1000 web. Step 1. Include a Z-Wave device via web. a) Go to "Z-Wave" and click "Device Configuration". b) Click” Include New Device” and the screen will appear with "Add Device: Waiting for a user action." c) Use a paper clip or pin to press the program button on the back of the sensor for 1 time to connect.
Z-Wave Wall-mount PIR Mostion Sensor HZS-100E/HZS-100A Step 2. Set up the location and room for Z-Wave device via HAC-1000 web. a. Create rooms in your environment. b. Edit device. Step 3. Create a scene via web. a. Click “Create Scene” and name new scene. b. Select a device from this scene.
Z-Wave Wall-mount PIR Mostion Sensor HZS-100E/HZS-100A c. Select ON or OFF from this scene. d. You can click “RUN” to run this scene. Step 4. Create trigger via web. a. Click “Create a Trigger” and name new trigger. b. Select a Z-Wave device for this trigger. c. Select when it triggers, it will alarm or bypass. d. Select when it triggers, it will run which scene.
Z-Wave Wall-mount PIR Mostion Sensor HZS-100E/HZS-100A After entering the time selected for the scene to trigger, tick “Save and send alarm notification”. Tick “Active” to enable this trigger. 3.2 Configuring Z-Wave via Smart Phone The HAC-1100 can be used on iOS and Android operating system. Cloud Home can be downloaded at Google Play store or app store. Please refer to the following steps to install Cloud Home app and add Z-Wave device via smart phone.
Z-Wave Wall-mount PIR Mostion Sensor HZS-100E/HZS-100A Step 1. Include a Z-Wave device via smart phone (Android/iOS). a. Register a user account. b. Setting c. Inclusion/Exclusion d. Click Inclusion to add device. e. Use a paper clip or pin to press the program button on the back of the sensor for 1 time to connect.
Z-Wave Wall-mount PIR Mostion Sensor HZS-100E/HZS-100A Step 2. Set up the location and room for Z-Wave device. b. Click “No Room” to show the device. a. Create rooms in your environment. And place the new device in a room. c. Select “Name” to name this device and select “Location” to place this device in the room that you created. e. Click “Back” to save. d. Select Picture for your Z-Wave device. f. - 14 - Done successfully.
Z-Wave Wall-mount PIR Mostion Sensor HZS-100E/HZS-100A Step 3. Create a scene via smart phone. a. Click “Add” and name a new scene. c. b. Click “Add” to add a Z-Wave device. d. Click ON or OFF for the device you select. Select a Z-Wave device. f. e. Click “Back” to save. - 15 - Done successfully.
Z-Wave Wall-mount PIR Mostion Sensor HZS-100E/HZS-100A Step 4. Create Trigger via smart phone. b. Name this new Trigger. a. Click “Add”. c. Select the Z-Wave device and click next. d. Select a mode for a Z-Wave device. e. Select a scene. f. Select the time for the trigger and which scene to run. h. If you enable Save and send alarm notification, when it triggers, it will have a log. You can check this in Notification History. g. Done successfully.
Z-Wave Wall-mount PIR Mostion Sensor HZS-100E/HZS-100A 3.3 Configuring Z-Wave via HTS-1000P Step 1. Fill out the IP of control gateway to connect with gateway. Click the button. “Gateway” Click the magnifying glass to search the IP of gateway. Control pad found an IP of gateway. Click the IP to join.
Z-Wave Wall-mount PIR Mostion Sensor HZS-100E/HZS-100A The default gateway port is 5000, and user name and password are both admin. Step 2. Include a Z-Wave device via HTS-1000P. Click the “Z-Wave devices” button to add Z-Wave devices to gateway. Click the “Include New Device” button to add Z-Wave device.
Z-Wave Wall-mount PIR Mostion Sensor HZS-100E/HZS-100A When you see the message “Waiting for user action”, you can press the match button on Z-Wave devices. Use a paper clip or pin to press the program button on the back of the sensor for 1 time to connect. If a device is added successfully, it will show the message: Command has completed successfully in device No. XX.
Z-Wave Wall-mount PIR Mostion Sensor HZS-100E/HZS-100A Click the “Exclude Device” button to exclude Z-Wave device. When you see the message “Waiting for user action”, you can press the match button on Z-Wave devices to exclude device. Step 3. After including Z-Wave devices in gateway, you can create different scenes with this function. You can set scenes to control your devices in Scene mode. Click the “Scene” button.
Z-Wave Wall-mount PIR Mostion Sensor HZS-100E/HZS-100A Click “Create Scene” and name the new scene. Select one device to add to the device list. Select one device. Click the “Plus” button to add device.
Z-Wave Wall-mount PIR Mostion Sensor HZS-100E/HZS-100A Select the status device (ON or OFF). of Click “All Scenes” check the scene. to Step 4. In Trigger mode, the trigger time is set. An alarm notification is sent via sensor. If a sensor is not installed, this step can be skipped. Click the button.
Z-Wave Wall-mount PIR Mostion Sensor HZS-100E/HZS-100A Click “Create Trigger”. Trigger: Name this trigger. Device: Select a Z-Wave device. Mode: Select “Arm” to enable alarm. Scene: When it triggers, the fan will turn on. Optional: After triggering for 5 seconds, the fan will turn off by itself. Switch to “AWAY” to enable monitor mode. When one of Z-Wave devices is triggered, control pad will alarm. Step 5. After configuring this part, you can control Z-Wave devices and scenes via control pad.
Z-Wave Wall-mount PIR Mostion Sensor HZS-100E/HZS-100A Click the three-line button on the upper right corner and click “Add Panel”. There are two types of panel that you can choose from. Name the panel. Click and hold for two seconds to select the device or scene.
Z-Wave Wall-mount PIR Mostion Sensor HZS-100E/HZS-100A Click on the Device field. Use a paper clip or pin to press the program button on the back of the sensor for 1 time to connect. Go back to the main page and click the “Control” button.
Z-Wave Wall-mount PIR Mostion Sensor HZS-100E/HZS-100A You can control scenes and devices here.
Z-Wave Wall-mount PIR Mostion Sensor HZS-100E/HZS-100A Appendix A: Troubleshooting & Frequently Asked Questions Features This difference between Z-Wave and ZigBee z The frequency is different between Z-Wave and ZigBee. ZigBee is 2.4GHz and Z-Wave is about 900MHz. z The outdoor distance is different. ZigBee is 10~75 meters and Z-Wave is about 30 meters. Z-Wave Device Installation How to reset the HZS-100 Series Use a paper clip or pin to press the program button for 10 times within 10 seconds.
