20 Meter IR Vandal Proof Dome Internet Camera ICA-525 Quick Installation Guide
Table of Contents Before Installation............................................................................................. 3 System Requirements ...................................................................................... 3 Package Content............................................................................................... 4 Identification of Cables...................................................................................... 5 Inside the TEL box:.........................
Thank you for purchasing the ICA-525. It is versatile and high image solution of surveillance application for day and night. The ICA-525 is also a stand-alone camera system with a built-in processor and web server that provides highest quality video and system performance. Before Installation Before installation, please be sure to read this quick installation guide or user’s manual of bundle CD carefully to complete machine installation.
Package Content ICA-525 x 1 Power Adapter x 1 Screws x 4 Telephone box x 1 L-Wrench x 1 CD Disk x 1 Quick Installation Guide x 1 Note 1. If any of the above items are missing, please contact your dealer immediately. 2. Using a power supply with a different voltage that the one included with the ICA-525 will cause damage and void the warranty for ICA-525.
Identification of Cables RJ-45 LAN Video out RS-485 & DI/DO (Connect to a bundled TEL box) Line in 12V DC in Line out 1. RJ45 LAN socket: Connect to PC or Hub/Switch. For connect to 10Base-T Ethernet or 100Base-TX Fast Ethernet cabling. This Ethernet port built N-Way protocol can detect or negotiate the transmission speed of the network automatically. Please use Category 5 “straight through” cable to connect the ICA-525 to a 100Mbps Fast Ethernet network switch or hub.
2. RS-485 & DI/DO: Connect to a local keyboard controller and connect to sensor in and alarm out devices. Inside the TEL box: Name Function 12VDC DC 12V output (50mA maximum) GND GND D+ RS485 data + D- RS485 data - DI Digital signal input DO Digital signal output The RS-485 of ICA-525 is master that can control external scanner. Note 3. Local Video output (BNC port): The Network Camera also provides composite video output.
Hardware Installation 1. Use the provided L-wrench, loosen the tamper-resistant housing cover (with screws still attached on the cover). The unit has factory installed side conduit entry and one may adjust the cables to back conduit entry according to installation requirement. Note During the installation, please take care and avoid crash. That may cause the device damage. 2.
3. Set the proper image by moving the camera body and set the focus by turning the lens to left or right direction. Note 1. Vari-Focal Dome Operation Guide: Once the picture appears on the monitor, open the cover and adjust the lens wrench to “NEAR f g FAR”, get the view zoom that you desire, and then adjust the focus wrench of the lens to obtain the best picture. After adjustment, tighten both wrenches. 2. During adjust focus, please take cares that don’t touch, collision and knock sensor.
5. When using the side conduit cabling, it is suggested to cover the cables using metal covers (to prevent external damage and for waterproof prevention), and wined the waterproof adhesive type onto the metal cover before installation. 6. Connect the LAN cable to Ethernet’s switch or hub and the DC-Jack to the power source. The video output to monitor or other video through a 75 Ohms type coaxial cable if you will use BNC cable. 7.
Initial Utility Installation and operation 1. Insert the bundled CD into the CD-ROM drive to launch the autorun program. Once completed, a welcome menu screen will appear. 2. Click the “IPWizard” hyperlink, you will see the InstallShield Wizard dialog box as below. Note If the welcome screen does not appear, click “Start” at the taskbar. Then, select “Run” and type “D:\Utility\setup.exe”, assume D is your CD-ROM drive. 3.
4. Please click “Next” to install with original settings, or you may click “Change…” button to modify the install folder then press “Next” to continue. 5. Please click “Install” to start the installation.
6. Please click “Finish” to complete the installation 7. Please double-click the utility icon ICA-525 utility. on the desktop then you will see the 8. Press “Search” button.
Wizard function: Note Please select your ICA-525 and press “Wizard”. The utility featured of “Wizard” function to help user to initial ICA-525. User can setup IP address, username and password step by step. Please enter User Name and Password. Default Username is: admin, leave password blank. Then click “Submit”.
Username and Password: You may change the ID and assign a new password to your ICA-525 or keep the original and press “Next” to continue. As below, you can select “Static IP” and enter the IP settings. Or select “DHCP ON” when there is a DHCP server in your network. If no IP address is assigned after 30 seconds, ICA-525 will use its default address 192.168.0.20. User may open your web browser, and key in http://192.168.0.
Configure Utility Installation Note The Cam Viewer Lite/Pro 30 days trial version installation steps are similar. Below is the installation of Cam Viewer Lite. 1. Insert the bundled Cam Viewer CD disk into the CD-ROM drive to launch the autorun program. Once completed, a welcome menu screen will appear. Click the “Cam Viewer Lite” hyperlink, the below InstallShield Wizard dialog box will appear. Note If the welcome screen does not appear, click “Start” at the taskbar.
3. The “Welcome to the InstallShield Wizard for Planet Cam Viewer Lite 1.0.0” will display on the screen, please click “Next”. 4.
5. Please key in user name and company name for which you want and click “Next” to continue installation. 6. Check the option “Complete” – all program features will be installed (Requires the most disk space) and click “Next” to continue installation.
7. “Ready to Install the Program” will appear to prompt you to start the installation. Please click “Install” to start. 8. Please click “No” to finish the Cam Viewer Lite installation. Note In above step, when Cam Viewer works with MBM5 (Motherboard Monitor 5), Cam Viewer will display CPU temperature and fan speed. Please click “Yes” if you need this function and refer to the manual of Cam Viewer CD disk for complete installation.
Appendix A: Feature Listing for Cam Viewer Software Version Cam Viewer Lite Cam Viewer Pro IP Camera Input 32 16 / 32 / 64 Dual Monitor - V Smart Guard - V I/O Device V Hotline - V Address Book - V Log Viewer Unusual event System log Unusual event System log Counting application Counting Application - 2 way counting Remote Playback Server - Unlimited Concurrent Playback 1 Channel 16 Channels Counting Function - V General Motion General Motion Missing Object Foreign Object
Appendix B: Suggest Hardware / System Requirement Total FPS ~600 600~480 480~240 240~120 120~ CPU Intel Core 2 Duo QX6800 Intel Core 2 Duo E6600 Intel Pentium D 930 Intel P4 3.0 GHz Intel P4 2.8 GHz RAM 4 GB 2 GB 2 GB 1 GB 1 GB Chipset of Motherboard Intel 946 or 965 chip, Intel Chipset recommended VGA Card ATI Radeon 9200, nVIDIA GeForce FX-5200, Intel 945/965 or above (ATI recommended) Ethernet 100 Base-TX or Above, Gigabit LAN recommended Hard Disk 160 GB or above O.S.
