0/100Base-TX to 100Base-FX Industrial Media Converter IFT-802T / IFT-802TS15 / IFT-805AT User's Manual
Trademarks Copyright © PLANET Technology Corp. 2010. Contents subject to revision without prior notice. PLANET is a registered trademark of PLANET Technology Corp. All other trademarks belong to their respective owners. Disclaimer PLANET Technology does not warrant that the hardware will work properly in all environments and applications, and makes no warranty and representation, either implied or expressed, with respect to the quality, performance, merchantability, or fitness for a particular purpose.
Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the Instruction manual, may cause harmful interference to radio communications.
Table Of Contents 1. Introduction...................................................................... 5 1.1 Package Contents........................................................ 5 1.2 How to Use This Manual ............................................. 5 1.3 Product Features......................................................... 6 1.4 Product Specifications.................................................. 7 2. Installation...................................................................... 10 2.
1. Introduction 1.1 Package Contents Check the contents of your package for following parts: ● 10/100Base-TX to 100Base-FX Industrial Media Converter x 1 ● User's Manual x 1 ● DIN Rail Kit x 1 ● Wall Mount Kit x 1 ● Screws x 1(set) If any of these are missing or damaged, please contact your dealer immediately, if possible, retain the carton including the original packing material, and use them against to repack the product in case there is a need to return it to us for repair. 1.
1.3 Product Features n Physical Port IFT-802T l 1-Port 10/100Base-TX RJ-45 l 1-Port 100Base-FX interface for up to 2km (Multi-mode fiber 62.
n Data Communication l Complies with the IEEE 802.3, IEEE 802.3u Fast Ethernet standard l Auto-MDI/MDI-X detection and Auto-negotiation with HalfDuplex / Full-Duplex modes for 10 / 100Base-TX RJ-45 port l Store-and-Forward switching architecture l Features Store-and-Forward mode with wire-speed filtering and forwarding rates l Prevents packet loss with back pressure (Half-Duplex) and IEEE 802.
Weight 430g Installation DIN rail kit and wall mount ear Maximum Frame Size 1522bytes packet size Flow Control Back pressure for half duplex, IEEE 802.
Speed Twisted-pair: • 10/20Mbps for Half / Full-Duplex • 100/200Mbps for Half / Full‑Duplex Fiber-optic: • 200Mbps for Full-Duplex Network Cables 10/100Base-TX: • 2-Pair UTP Cat. 3, 4, 5 (100meters, max.) • EIA/TIA-568 100-ohm STP (100meters, max.) 100Base-FX: • IFT-802T: Multi-mode optic fiber 62.
2. Installation This section describes the functionalities of the Industrial Media Converter’s components and guides how to install it on the desktop. Basic knowledge of networking is assumed. Please read this chapter completely before continuing. In the following section, the term “Industrial Media Converter” means the IFT-802T / 802TS15 / 805AT. 2.1 Product Description The IFT-80xT are industrially hardened media converters which specially designed to operate under -40 to 75˚C environment temperature.
With Fast Ethernet SFP interface, the IFT-805AT is with high reliability and flexibility to extend the distance from 2km to 60Km. It depends on the MFB family Fast Ethernet SFP modules. MFB family Fast Ethernet SFP module comes with one of the following models.
2.1.1 Media Converter Front Panel Figure 2-1 & 2-2 shows a front panel of Industrial Media Converter. P1 P2 FAULT P1 P2 FAULT TX 100 100 RX LNK/ACT LNK/ACT 100Base-FX 100Base-FX 100 100 LNK/ACT LNK/ACT 10/100Base-TX IFT-802T Figure 2-1 IFT-802T / IFT-802TS15 front panel 10/100Base-TX IFT-805AT Figure 2-2 IFT-805AT front panel 2.1.2 LED Indicators l System LED Color Function P1 Green Lit: indicate the power 1 has power. P2 Green Lit: indicate the power 2 has power.
l 10/100Base-TX RJ-45 Port LED 10/100 Color Green LNK/ACT Green Function Lit: To indicate TP port is successfully connecting to the network at 100Mbps. Off: To indicate TP port is successfully connecting to the network at 10Mbps. Lit: To indicate the link through that port is successfully established. Blink: To indicate TP port is actively sending or receiving data over that port.
2.1.4 Wiring the Power Inputs The 6-contact terminal block connector on the top panel of Industrial Media Converter is used for two DC redundant powers input. Please follow the steps below to insert the power wire. 1. Insert positive / negative DC power wires into the contacts 1 and 2 for POWER 1, or 5 and 6 for POWER 2. V1- V1 + V2 - V2 + 2. Tighten the wire-clamp screws for preventing the wires from loosing.
2.1.5 Wiring the Fault Alarm Contact The fault alarm contacts are in the middle of the terminal block connector as the picture shows below. Inserting the wires, the Industrial Media Converter will detect the fault status of the power failure, or port link failure (available for managed model) and then forms an open circuit. The following illustration shows an application example for wiring the fault alarm contacts. Insert the wires into the fault alarm contacts Note 1.
2.2 Mounting Installation This section describes how to install the Industrial Media Converter and make connections to it. Please read the following topics and perform the procedures in the order being presented. Note In the installation steps below, this Manual use IGS-801(PLANET 8 Port Industrial Gigabit Switch) as the example. However, the steps for PLANET Industrial Media Converter are similar. 2.2.
1 2 Step 2: Lightly press the button of DIN-Rail into the track. Step 3: Check the DIN-Rail is tightly on the track. Step 4: Please refer to following procedures to remove the Industrial Media Converter from the track.
1 2 Step 5: Lightly press the button of DIN-Rail for remove it from the track. 2.2.2 Wall Mount Plate Mounting To install the Industrial Media Converter on the wall, please follows the instructions described below. Step 1: Remove the DIN-Rail from the Industrial Media Converter; loose the screws to remove the DIN-Rail. Step 2: Place the wall mount plate on the rear panel of the Industrial Media Converter.
Step 3: Use the screws to screw the wall mount plate on the Industrial Media Converter. Step 4: Use the hook holes at the corners of the wall mount plate to hang the Industrial Media Converter on the wall. Step 5: To remove the wall mount plate, reverse steps above.
3. Application In this paragraph, we will describe how to install Industrial Media Converter and the installation points for the attention. 3.1 Installation Steps Step 1: Unpack the Industrial Media Converter. Step 2: Check the DIN-Rail is screwed on the Industrial Media Converter. (Please refer to DIN-Rail Mounting section for DIN-Rail installation (If the DIN-Rail is not screwed on the Industrial Media Converter).
Step 3: To hang the Industrial Media Converter on the DINRail track or wall, please refer to the Mounting Installation section. Step 4: Power on the Industrial Media Converter. (Please refer to the Wiring the Power Inputs section for power input) The power LED on the Industrial Media Converter will light up. Please refer to the LED Indicators section for meaning of LED lights. Step 5: Prepare the twisted-pair, straight through Category 5 cable for Ethernet connection.
4. Media Converter Operation 4.1 Learning When one packet comes in from any port. The Industrial Media Converter will record the source address, port no. And the other related information in address table. This information will be used to decide either forwarding or filtering for future packets. 4.2 Forwarding & Filtering When one packet comes from some port of the Industrial Media Converter, it will also check the destination address besides the source address learning.
The Industrial Media Converter scans the destination address from the packet-header, searches the routing table provided for the incoming port and forwards the packet, only if required. The fast forwarding makes the media converter attractive for connecting servers directly to the network, thereby increasing throughput and availability. However, the media converter is most commonly used to segment existing hubs, which nearly always improves overall performance.
5. Troubleshooting This chapter contains information to help you solve issues. If the Industrial Media Converter is not functioning properly, make sure the Industrial Media Converter was set up according to instructions in this manual. The per port LED is not lit Solution: Check the cable connection of the Industrial Media Converter. Performance is bad Solution: Check the speed duplex mode of the partner device.
Why the Industrial Media Converter doesn’t connect to the network Solution: Check per port LED on the Industrial Media Converter. Try another port on the Industrial Media Converter Make sure the cable is installed properly Make sure the cable is the right type Turn off the power. After a while, turn on power again. Why I connect IFT-80xT to device with 100Base-FX interface and the 100Base-FX fiber connection fail? Solution: 1. Please check the fiber connection between two devices is correct. 2.
Appendix A: Networking Connection A.1 Media Converter’s RJ-45 Pin Assignments 10/100Mbps, 10/100Base-TX RJ-45 Connector pin assignment Contact MDI Media Dependant Interface MDI-X Media Dependant Interface-Cross 1 Tx + (transmit) Rx + (receive) 2 Tx - (transmit) Rx - (receive) 3 Rx + (receive) Tx + (transmit) 4, 5 6 7, 8 Not used Rx - (receive) Tx - (transmit) Not used A.
Straight Cable 1 2 3 4 5 6 7 8 SIDE 1 1 2 3 4 5 6 7 8 SIDE 2 SIDE 1 SIDE 2 1 = White/Orange 2 = Orange 3 = White/Green 4 = Blue 5 = White/Blue 6 = Green 7 = White/Brown 8 = Brown 1 = White/Orange 2 = Orange 3 = White/Green 4 = Blue 5 = White/Blue 6 = Green 7 = White/Brown 8 = Brown Cross Over Cable 1 2 3 4 5 6 7 8 SIDE 1 1 2 3 4 5 6 7 8 SIDE 2 SIDE 1 SIDE 2 1 = White/Orange 2 = Orange 3 = White/Green 4 = Blue 5 = White/Blue 6 = Green 7 = White/Brown 8 = Brown 1 = White/Green 2 = Green 3 = White
EC Declaration of Conformity For the following equipment: *Type of Product: *Model Number: 10/100Base-TX to 100Base-FX Industrial Media Converter with Wide Operating Temperature IFT-802T / IFT-802TS15 / IFT-805AT * Produced by: Manufacturer‘s Name : Manufacturer‘s Address: Planet Technology Corp. 11F, No 96, Min Chuan Road, Hsin Tien, Taipei, Taiwan, R.O.C.
