Industrial L2+ Managed Gigabit/ 10 Gigabit Ethernet Switch IGS-5225 Series Quick Installation Guide
Table of Contents 1. Package Contents........................................................................................ 3 2. Requirements.............................................................................................. 4 3. Wiring DC Power Inputs............................................................................... 5 4. Terminal Setup............................................................................................ 7 5. Logon to Console.................................
1. Package Contents Thank you for purchasing PLANET Industrial L2+ Managed Gigabit/10 Gigabit Ethernet Switch. The description of this model is shown below: IGS-5225-16T4S Industrial L2+ 16-port 10/100/1000T + 4-port 100/1000X SFP Managed Ethernet Switch (-40~75 degrees C) IGS-5225-20T4C2X Industrial L2+ 20-port 10/100/1000T + 4-port TP/SFP Combo + 2-port 10G SFP+ Managed Ethernet Switch (-40~75 degrees C) IGS-5225-16P4S Industrial L2+ 16-port 10/100/1000T 802.
2. Requirements zz Workstations running Windows XP/2003/Vista/7/8/2008/10, MAC OS X or later, Linux, UNIX, or other platforms are compatible with TCP/IP Protocols. zz Workstations are installed with Ethernet NIC (Network Interface Card) zz Serial Port Connection (Terminal) The above Workstations come with COM Port (DB9) or USB-to-RS232 converter. The above Workstations have been installed with terminal emulator, such as Hyper Terminal included in Windows XP/2003, putty or tera term.
3. Wiring DC Power Inputs The 6-contact terminal block connector on the rear panel of Industrial Managed Switch is used for two DC redundant power input. Please follow the steps below to insert the power wires. 1. Insert positive/negative DC power wires into contacts 1 and 2 for DC POWER 1, or 5 and 6 for DC POWER 2. 100~240V AC 2 DC POWER ON AC POWER ON DI 0 DI 1 DO 0 DO 1 GND GND AC DC 1 Ring DC 2 R.O.
2. Tighten the wire-clamp screws for preventing the wires from loosening. 1 2 3 4 5 6 V1+ V1- V2+ V2Power 1 Power 2 Positive (+) Pin Negative (-) Pin IGS-5225-16T4S Pin 1/5 Pin 2/6 IGS-5225-20T4C2X Pin 1/5 Pin 2/6 IGS-5225-16P4S Pin 1/5 Pin 2/6 IGS-5225-24P4S Pin 1/5 Pin 2/6 Note 6 The wire gauge for the terminal block should be in the range between 12 and 24 AWG.
4. Terminal Setup To configure the system, connect a serial cable to a COM port on a PC or notebook computer and to RJ45 type of serial port of the Industrial Managed Switch. PC / Workstation with Terminal Emulation Software Managed Switch RS232 to RJ45 Cable Serial Port RJ45 Console Port Figure 4-1 Industrial Managed Switch Console Connectivity A terminal program is required to make the software connection to the Industrial Managed Switch. 1. Run terminal program on the OS. 2.
5. Logon to Console Once the terminal is connected to the device, power on the Industrial Managed Switch and the terminal will display “running testing procedures”. Then, the following message asks to log-in user name and password. The factory default user name and password are shown as follows and the login screen in Figure 5-1 appears. Username: admin Password: admin Figure 5-1: Industrial Managed Switch Console Login Screen The user can now enter commands to manage the Industrial Managed Switch.
6. Configuring IP Address via Console The Industrial Managed Switch is shipped with default IP address shown below. IP Address: 192.168.0.100 Subnet Mask: 255.255.255.0 To check the current IP address or modify a new IP address for the Switch, please use the procedure as follows: Show the current IP Address 1. At the “#” prompt, enter “show ip interface brief”. 2. The screen displays the current IP address as shown in Figure 6-1. Figure 6-1: IP Information Screen Configuring IP Address 3.
4. Repeat step 1 to check if the IP address has changed. Store the current switch configuration 5. At the “#” prompt, enter the following command and press . # copy running-config startup-config Figure 6-3: Saving Current Configuration Command Screen If the IP is successfully configured, the Industrial Managed Switch will apply the new IP address setting immediately. You can access the Web interface of the Industrial Managed Switch through the new IP address.
7. Starting Web Management The following shows how to start up the Web Management of the Industrial Managed Switch. Note the Industrial Managed Switch is configured through an Ethernet connection. Please make sure the manager PC must be set to the same IP subnet address. For example, the default IP address of the Industrial Managed Switch is 192.168.0.100, then the manager PC should be set to 192.168.0.x (where x is a number between 1 and 254, except 100), and the default subnet mask is 255.255.255.0.
Figure 7-2: Login Screen 3. After entering the password, the main screen appears as Figure 7-3 shows.
The Switch Menu on the left of the Web page lets you access all the commands and statistics the Industrial Managed Switch provides. Figure 7-4: Switch Menu Note If you are not familiar with Switch functions or the related parameter, press “Help icon” anytime on the Web page to get the help description. Now, you can use the Web management interface to continue the Switch management or manage the Switch by console interface. Please refer to the user’s manual for more.
8. Saving Configuration via Web In the Industrial Managed Switch, the running configuration file stores in the RAM. In the current version, the running configuration sequence of running-config can be saved from the RAM to FLASH by executing save startup config command, so that the running configuration sequence becomes the startup configuration file, which is called configuration save.
9. Recovering Back to Default Configuration IP address has been changed or admin password has been forgotten – To reset the IP address to the default IP address “192.168.0.100” or reset the login password to default value, press the hardware reset button on the rear panel for about 10 seconds. After the device is rebooted, you can login the management Web interface within the same subnet of 192.168.0.xx.
10. Customer Support Thank you for purchasing PLANET products. You can browse our online FAQ resource and User’s Manual on PLANET Web site first to check if it could solve your issue. If you need more support information, please contact PLANET switch support team. PLANET online FAQ: http://www.planet.com.tw/en/support/faq.php?type=1 Switch support team mail address: support_switch@planet.com.tw Industrial User’s Manual: http://www.planet.com.tw/en/support/download.
