IGS-5225 Series User Manual

ManualsBrandsPLANET Technology ManualsIndustrial EthernetIndustrial L2+ 16-Port 10/100/1000T + 4-Port 100/1000X SFP Managed Ethernet Switch

Table Of Contents

Command Guide

-1-

Summary of content (433 pages)

PAGE 1
Command Guide -1-
PAGE 2
Command Guide Contents Chapter 1 COMMAND LINE INTERFACE ........................................................ 20 1.1 Accessing the CLI ....................................................................................................... 20 1.2 Command Line Modes ................................................................................................ 20 1.3 Requirements .............................................................................................................. 21 1.
PAGE 3
Command Guide 4.1.19 clear ip igmp snooping statistics ........................................................................................................................37 4.1.20 clear ip igmp snooping vlan ............................................................................................................................... 37 4.1.21 clear ip statistics icmp icmp-msg .......................................................................................................................38 4.1.
PAGE 4
Command Guide 4.2.4 aaa authentication login http local .......................................................................................................................54 4.2.5 aaa authentication login http radius .....................................................................................................................55 4.2.6 aaa authentication login http tacacs ....................................................................................................................55 4.2.
PAGE 5
Command Guide 4.2.45 erps <1-64> rpl neighbor ...................................................................................................................................78 4.2.46 erps <1-64> rpl owner .......................................................................................................................................78 4.2.47 erps <1-64> sub ..............................................................................................................................................
PAGE 6
Command Guide 4.2.65.21 evc l2cp forward(GG) ..........................................................................................................................106 4.2.65.22 evc l2cp peer(GG) ............................................................................................................................... 107 4.2.65.23 evc update dei .....................................................................................................................................107 4.2.65.
PAGE 7
Command Guide 4.2.65.62 loop-protect tx-mode ...........................................................................................................................127 4.2.65.63 loop-protect tx-mode ...........................................................................................................................128 4.2.65.64 mac address-table learning .................................................................................................................128 4.2.65.65 media-type........
PAGE 8
Command Guide 4.2.65.103 qos storm unicast .............................................................................................................................. 150 4.2.65.104 qos storm unknown ...........................................................................................................................150 4.2.65.105 qos tag-remark ..................................................................................................................................151 4.2.65.
PAGE 9
Command Guide 4.2.66.5 ip address dhcp .....................................................................................................................................173 4.2.66.6 ip address dhcp fallback ........................................................................................................................174 4.2.66.7 ip dhcp server ........................................................................................................................................174 4.2.66.
PAGE 10
Command Guide 4.2.73.11 hardware-address ............................................................................................................................... 196 4.2.73.12 host .....................................................................................................................................................197 4.2.73.13 lease ....................................................................................................................................................197 4.
PAGE 11
Command Guide 4.2.96 ipv6 mld host-proxy leave-proxy ......................................................................................................................218 4.2.97 ipv6 mld snooping............................................................................................................................................218 4.2.98 ipv6 mld snooping vlan ....................................................................................................................................219 4.
PAGE 12
Command Guide 4.2.123 mep ais .......................................................................................................................................240 4.2.124 mep aps ......................................................................................................................................241 4.2.125 mep cc ........................................................................................................................................
PAGE 13
Command Guide 4.2.164 network-clock clk-source aneg-mode .......................................................................................266 4.2.165 no ..................................................................................................................................................................267 4.2.166 ntp .................................................................................................................................................................
PAGE 14
Command Guide 4.2.199 rmon alarm ....................................................................................................................................................294 4.2.200 rmon event ....................................................................................................................................................295 4.2.201 sflow agent-ip .....................................................................................................................................
PAGE 15
Command Guide 4.2.219 transport email smtp-server ...........................................................................................................................317 4.2.220 transport email to ...........................................................................................................................................318 4.2.221 upnp ........................................................................................................................................................
PAGE 16
Command Guide 4.11.1 erps ..................................................................................................................................................................334 4.12 exit............................................................................................................................ 335 4.12.1 exit ...................................................................................................................................................................
PAGE 17
Command Guide 4.21.14 show evc .......................................................................................................................................................355 4.21.15 show evc statistics .........................................................................................................................................356 4.21.16 show green-ethernet..................................................................................................................................
PAGE 18
Command Guide 4.21.55 show ipv6 mld snooping mrouter ...................................................................................................................384 4.21.56 show ipv6 neighbor........................................................................................................................................384 4.21.57 show ipv6 route .............................................................................................................................................385 4.21.
PAGE 19
Command Guide 4.21.96 show snmp view ............................................................................................................................................419 4.21.97 show spanning-tree .......................................................................................................................................420 4.21.98 show switchport forbidden .............................................................................................................................
PAGE 20
Command Guide Chapter 1 COMMAND LINE INTERFACE 1.1 Accessing the CLI When accessing the management interface for the switch over a direct connection to the server’s console port, or via a Telnet connection, the switch can be managed by entering command keywords and parameters at the prompt. Using the switch's command-line interface (CLI) is very similar to entering commands on a UNIX system. This chapter describes how to use the Command Line Interface (CLI). 1.
PAGE 21
Command Guide  User Mode When the operator logs into the CLI, the User Mode is the initial mode. The User Mode contains a limited set of commands. The command prompt shown at this level is: Command Prompt: switch>  Privileged Mode To have access to the full suite of commands, the operator must enter the Privileged Mode. The Privileged Mode requires password authentication. From Privileged Mode, the operator can issue any Exec command to enter the Global Configuration mode.
PAGE 22
Command Guide 1.4 Command Support As shown in the following table, some command groups or commands are supported on particular switch models. Command Group or Command IGS-5225-16T4S IGS-5225-20T4C2X IGS-5225-24P4S 10 Gigabit Ethernet Power over Ethernet - - ■ - ■ = Supported, - = Not supported -22- E.R.P.
PAGE 23
Command Guide Chapter 2 CONSOLE CLI MANAGEMENT 2.1 Terminal Setup To configure the system, connect a serial cable to a COM port on a PC or notebook computer and to RJ45 type of serial (console) port of the Industrial Managed Switch. Figure 2-1 Industrial Managed Switch Console Connectivity The console port of the Industrial Managed Switch is an RJ45 type, RS-232 serial port connector. It is an interface for connecting a terminal directly.
PAGE 24
Command Guide Figure 2-3 Hyper Terminal COM Port Configuration You can change these settings, if desired, after you log on. This management method is often preferred because you can remain connected and monitor the system during system reboots. Also, certain error messages are sent to the serial port, regardless of the interface through which the associated action was initiated. A Macintosh or PC attachment can use any terminal-emulation program for connecting to the terminal serial port.
PAGE 25
Command Guide 2.2 Logon to the Console Once the terminal is connected to the device, power on the Industrial Managed Switch, and the terminal will display “running testing procedures”. Then, the following message asks to log-in user name and password. The factory default user name and password are shown as follows and the login screen in Figure 3-1 appears.
PAGE 26
Command Guide  Show the current IP Address 1. At the “#” prompt, enter “show ip interface brief”. 2. The screen displays the current IP address and Subnet Mask as shown in Figure 3-2. Figure 3-2: IP Information Screen  Configuring IP Address 3. At the “#” prompt, enter the following command and press .as shown in Figure 3-3. # configure terminal (config)# interface vlan 1 (config-if-vlan)# ip address 192.168.1.100 255.255.255.
PAGE 27
Command Guide 4.  Repeat step 1 to check if the IP address is changed. Store current switch configuration 5. At the “#” prompt, enter the following command and press . # copy running-config startup-config Figure 3-4: Saving Current Configuration Command Screen If the IP is successfully configured, the Industrial Managed Switch will apply the new IP address setting immediately. You can access the Web interface of the Industrial Managed Switch through the new IP address.
PAGE 28
Command Guide Chapter 3 TELNET CLI MANAGEMENT 3.1 Telnet Login The Industrial Managed Switch also supports telnet for remote management. The switch asks for user name and password for remote login when using telnet, please use “admin” for both username and password. Default IP address: 192.168.0.
PAGE 29
Command Guide Chapter 4 Commands for CLI Configuration 4.1 clear 4.1.1 clear access management statistics Command: clear access management statistics Default: N/A Usage Guide: To clear the access management statistics. Example: To clear the Switch’s access management statistics. Switch# clear access management statistics 4.1.2 clear access-list ace statistics Command: clear access-list ace statistics Default: N/A Usage Guide: To clear the Access list entry statistics.
PAGE 30
Command Guide 4.1.3 clear dot1x statistics interface Command: clear dot1x statistics interface GigabitEthernet | 10GigabitEthernet Default: N/A Usage Guide: To clear the dot1x statistics. Example: To clear the Switch’s GigabitEthernet 1/25 dot1x statistics. Switch# clear dot1x statistics interface GigabitEthernet 1/25 4.1.4 clear eps Command: clear eps The EPS instance number. Default: N/A Usage Guide: To clear the EPS instance number. 4.1.
PAGE 31
Command Guide Example: To clear the Switch’s ERPS group 1 statistics. Switch# # clear erps 1 statistics 4.1.6 clear erps statistics Command: clear erps statistics Default: N/A Usage Guide: To clear the ERPS statistics. Example: To clear the Switch’s ERPS statistics. Switch# clear erps statistics 4.1.7 clear evc statistics Command: clear evc statistics Default: N/A Usage Guide: To clear the Ethernet Virtual Connections statistics. Example: To clear the Switch’s Ethernet Virtual Connections statistics.
PAGE 32
Command Guide 4.1.8 clear ip arp Command: clear ip arp Default: N/A Usage Guide: To clear the ARP cache. Example: To clear the Switch’s ARP cache. Switch# clear ip arp 4.1.9 clear ip dhcp detailed statistics all Command: clear ip dhcp detailed statistics all Default: N/A Usage Guide: To clear the DHCP detailed statistics for all. Example: To clear the Switch’s DHCP detailed statistics for all.
PAGE 33
Command Guide 4.1.10 clear ip dhcp detailed statistics client Command: clear ip dhcp detailed statistics client Default: N/A Usage Guide: To clear the DHCP client statistics. Example: To clear the Switch’s DHCP client statistics. Switch# clear ip dhcp detailed statistics client 4.1.11 clear ip dhcp detailed statistics helper Command: clear ip dhcp detailed statistics helper Default: N/A Usage Guide: To clear the DHCP normal L2 or L3 forward statistics.
PAGE 34
Command Guide 4.1.12 clear ip dhcp detailed statistics server Command: clear ip dhcp detailed statistics server Default: N/A Usage Guide: To clear the DHCP server statistics. Example: To clear the Switch’s DHCP server statistics. Switch# clear ip dhcp detailed statistics server 4.1.13 clear ip dhcp detailed statistics snooping Command: clear ip dhcp detailed statistics snooping Default: N/A Usage Guide: To clear the DHCP snooping statistics.
PAGE 35
Command Guide 4.1.14 clear ip dhcp relay statistics Command: clear ip dhcp relay statistics Default: N/A Usage Guide: To clear the DHCP relay statistics. Example: To clear the Switch’s DHCP relay statistics. Switch# clear ip dhcp relay statistics 4.1.15 clear ip dhcp server binding Command: clear ip dhcp server binding A.B.C.D Default: N/A Usage Guide: To clear the DHCP server binding cache. Example: To clear the Switch’s DHCP server(192.168.0.100) binding cache.
PAGE 36
Command Guide Default: N/A Usage Guide: To clear the DHCP automatic bindings cache. Example: To clear the Switch’s DHCP automatic bindings cache. Switch# clear ip dhcp server binding automatic 4.1.17 clear ip dhcp server binding expired Command: clear ip dhcp server binding expired Default: N/A Usage Guide: To clear the DHCP expired bindings for free. Example: To clear the Switch’s DHCP expired bindings for free. Switch# clear ip dhcp server binding expired 4.1.
PAGE 37
Command Guide 4.1.19 clear ip igmp snooping statistics Command: clear ip igmp snooping statistics Default: N/A Usage Guide: To clear the IGMP snooping statistics. Example: To clear the Switch’s IGMP snooping statistics. Switch# clear ip igmp snooping statistics 4.1.20 clear ip igmp snooping vlan Command: clear ip igmp snooping vlan < vlan_list> statistics VLAN identifier(s): VID Default: N/A Usage Guide: To clear the IGMP snooping vlan < vlan_list> statistics.
PAGE 38
Command Guide 4.1.21 clear ip statistics icmp icmp-msg Command: clear ip statistics icmp icmp-msg ICMP message type ranges from 0 to 255 Default: N/A Usage Guide: To clear the IPv4 ICMP traffic for designated message type. Example: To clear the Switch’s IPv4 ICMP traffic for designated message type 0. Switch# clear ip statistics icmp icmp-msg 0 4.1.
PAGE 39
Command Guide 4.1.23 clear ip statistics system icmp icmp-msg Command: clear ip statistics system icmp icmp-msg ICMP message type ranges from 0 to 255 Default: N/A Usage Guide: To clear the IPv4 ICMP statistics for specific ICMP message type. Example: To clear the Switch’s IPv4 ICMP statistics for specific ICMP message type 0. Switch# clear ip statistics system icmp icmp-msg 0 4.1.
PAGE 40
Command Guide 4.1.25 clear ipv6 mld snooping statistics Command: clear ipv6 mld snooping statistics Default: N/A Usage Guide: To clear the ipv6 mld snooping statistics. Example: To clear the Switch’s ipv6 mld snooping statistics. Switch# clear ipv6 mld snooping statistics 4.1.26 clear ipv6 mld snooping vlan Command: clear ipv6 mld snooping vlan statistics VLAN identifier(s): VID Default: N/A Usage Guide: To clear the ipv6 mld snooping statistics for specific VLAN.
PAGE 41
Command Guide 4.1.27 clear ipv6 neighbors Command: clear ipv6 neighbors Default: N/A Usage Guide: To clear the ipv6 neighbors. Example: To clear the Switch’s ipv6 neighbors. Switch# clear ipv6 neighbors 4.1.28 clear ipv6 statistics icmp icmp-msg Command: clear ipv6 statistics icmp icmp-msg ICMP message type ranges from 0 to 255 Default: N/A Usage Guide: To clear the IPv6 ICMP traffic for designated message type.
PAGE 42
Command Guide 4.1.29 clear ipv6 statistics icmp interface vlan Command: clear ipv6 statistics icmp interface vlan VLAN identifier(s): VID Default: N/A Usage Guide: To clear the IPv6 interface/ICMP statistics for specific VLAN. Example: To clear the Switch’s IPv6 interface/ICMP statistics for specific VLAN 1. Switch# clear ipv6 statistics icmp interface vlan 1 4.1.
PAGE 43
Command Guide 4.1.31 clear ipv6 statistics system icmp interface vlan Command: clear ipv6 statistics system icmp interface vlan VLAN identifier(s): VID Default: N/A Usage Guide: To clear the IPv6 ICMP interface statistics for specific VLAN. Example: To clear the Switch’s IPv6 ICMP interface statistics for specific VLAN 1. Switch# clear ipv6 statistics system icmp interface vlan 1 4.1.
PAGE 44
Command Guide 4.1.33 clear lldp statistics Command: clear lldp statistics Default: N/A Usage Guide: To clear the lldp statistics. Example: To clear the Switch’s lldp statistics. Switch# clear lldp statistics 4.1.34 clear logging error info Command: clear logging error info Default: N/A Usage Guide: To clear the logging error info. Example: To clear the Switch’s logging error info.
PAGE 45
Command Guide 4.1.35 clear logging error warning Command: clear logging error warning Default: N/A Usage Guide: To clear the logging error warning. Example: To clear the Switch’s logging error warning. Switch# clear logging error warning 4.1.36 clear logging info error Command: clear logging info error Default: N/A Usage Guide: To clear the logging info error. Example: To clear the Switch’s logging info error. Switch# clear logging info error 4.1.
PAGE 46
Command Guide Example: To clear the Switch’s logging info warning. Switch# clear logging info warning 4.1.38 clear logging warning error Command: clear logging warning error Default: N/A Usage Guide: To clear the logging warning error. Example: To clear the Switch’s logging warning error. Switch# clear logging warning error 4.1.39 clear logging warning info Command: clear logging warning info Default: N/A Usage Guide: To clear the logging warning info.
PAGE 47
Command Guide 4.1.40 clear mac address-table Command: clear mac address-table Default: N/A Usage Guide: To clear the mac address-table. Example: To clear the Switch’s mac address-table. Switch# clear mac address-table 4.1.41 clear mep Command: clear mep The MEP instance. Default: N/A Usage Guide: To clear the MEP instance profiles. 4.1.
PAGE 48
Command Guide 4.1.43 clear mvr statistics Command: clear mvr statistics Default: N/A Usage Guide: To clear the mvr statistics. Example: To clear the Switch’s mvr statistics. Switch# clear mvr statistics 4.1.44 clear mvr vlan Command: clear mvr vlan statistics MVR multicast VLAN list Default: N/A Usage Guide: To clear the mvr vlan statistics for specific VLAN. Example: To clear the Switch’s mvr vlan statistics for specific VLAN 1. Switch# clear mvr vlan 1 statistics 4.1.
PAGE 49
Command Guide Usage Guide: To clear the ERPS WTR timer for a specific profile. Example: To clear the Switch’s ERPS WTR timer for a specific profile 1. Switch# clear network-clock clk-source 1 4.1.46 clear spanning-tree detected-protocols interface * Command: clear spanning-tree detected-protocols interface * Default: N/A Usage Guide: To clear the spanning-tree detected-protocols for all. Example: To clear the Switch’s spanning-tree detected-protocols for all.
PAGE 50
Command Guide 4.1.48 clear spanning-tree detected-protocols interface GigabitEthernet Command: clear spanning-tree detected-protocols interface GigabitEthernet Port list in X/X-XX Default: N/A Usage Guide: To clear the spanning-tree detected-protocols for specific GigabitEthernet port. Example: To clear the Switch’s spanning-tree detected-protocols for specific GigabitEthernet 1/1. Switch# clear spanning-tree detected-protocols interface GigabitEthernet 1/1 4.1.
PAGE 51
Command Guide 4.1.50 clear spanning-tree statistics interface * Command: clear spanning-tree statistics interface * Default: N/A Usage Guide: To clear the spanning-tree statistics for all. Example: To clear the Switch’s spanning-tree statistics for all. Switch# clear spanning-tree statistics interface * 4.1.
PAGE 52
Command Guide Usage Guide: To clear the spanning-tree statistics for specific 10GigabitEthernet port. Example: To clear the Switch’s spanning-tree statistics for specific 10GigabitEthernet 1/1. Switch# clear spanning-tree statistics interface 10GigabitEthernet 1/1 4.1.53 clear statistics * Command: clear statistics * Default: N/A Usage Guide: To clear the statistics for all. Example: To clear the Switch’s statistics for all. Switch# clear statistics * 4.1.
PAGE 53
Command Guide 4.1.55 clear statistics 10GigabitEthernet Command: clear statistics 10GigabitEthernet Port list in X/X-XX Default: N/A Usage Guide: To clear the statistics for specific 10GigabitEthernet port. Example: To clear the Switch’s statistics for specific 10GigabitEthernet 1/1. Switch# clear statistics 10GigabitEthernet 1/1 4.2 configure terminal 4.2.
PAGE 54
Command Guide 4.2.2 aaa authentication login console radius Command: aaa authentication login console radius Default: console : local Usage Guide: To authenticate the radius account via console only. Example: To authenticate the local and radius account via console. Switch# configure terminal Switch (config)# aaa authentication login console local radius 4.2.
PAGE 55
Command Guide Usage Guide: To authenticate the local account via http only. Example: To authenticate the local account via http. Switch# configure terminal Switch (config)# aaa authentication login http local 4.2.5 aaa authentication login http radius Command: aaa authentication login http radius Default: http : local Usage Guide: To authenticate the radius account via http only. Example: To authenticate the local and radius account via http.
PAGE 56
Command Guide Example: To authenticate the local and radius and tacacs account via http. Switch# configure terminal Switch (config)# aaa authentication login http local radius tacacs 4.2.7 aaa authentication login ssh local Command: aaa authentication login ssh local Default: ssh : local Usage Guide: To authenticate the local account via ssh only. Example: To authenticate the local account via ssh. Switch# configure terminal Switch (config)# aaa authentication login ssh local 4.2.
PAGE 57
Command Guide 4.2.9 aaa authentication login ssh tacacs Command: aaa authentication login ssh tacacs Default: ssh : local Usage Guide: To authenticate the tacacs account via ssh only. Example: To authenticate the local and radius and tacacs account via console. Switch# configure terminal Switch (config)# aaa authentication login ssh local radius tacacs 4.2.
PAGE 58
Command Guide 4.2.11 aaa authentication login telnet radius Command: aaa authentication login telnet radius Default: telnet : local Usage Guide: To authenticate the radius account via telnet only. Example: To authenticate the local and radius account via telnet. Switch# configure terminal Switch (config)# aaa authentication login telnet local radius 4.2.
PAGE 59
Command Guide 4.2.
PAGE 60
Command Guide action Access list action dmac-type The type of destination MAC address frametype Frame type ingress Ingress logging Logging frame information. Note: The logging feature only works when the packet length is less than 1518 (without VLAN tags) and the System Log memory size and logging rate are limited. next Insert the current ACE before the next ACE ID policy Policy rate-limiter Rate limiter redirect Redirect frame to specific port shutdown Shutdown incoming port.
PAGE 61
Command Guide interface 10GigabitEthernet | GigabitEthernet } | tag-priority {0-1, 0-3, 2-3, 4-5, 4-7, 6-7, , any} | vid {, any} ACE ID action Access list action dmac-type The type of destination MAC address frametype Frame type ingress Ingress logging Logging frame information. Note: The logging feature only works when the packet length is less than 1518 (without VLAN tags) and the System Log memory size and logging rate are limited.
PAGE 62
Command Guide 4.2.16 access-list rate-limiter Command: access-list rate-limiter pps Rate limiter ID Rate value Default: 0 Usage Guide: To set pps rate for specific rate-limiter ID. Example: To set pps rate(10000 pps) for specific rate-limiter ID 1. Switch# configure terminal Switch (config)# access-list rate-limiter 1 pps 10000 4.2.
PAGE 63
Command Guide 4.2.18 aggregation mode Command: aggregation mode dmac | ip | port | smac dmac Destination MAC affects the distribution ip IP address affects the distribution port IP port affects the distribution smac Source MAC affects the distribution Default: SMAC : Enabled DMAC : Disabled IP : Enabled Port : Enabled Usage Guide: To configure static aggregation mode type.
PAGE 64
Command Guide Usage Guide: To configure static aggregation mode type. Example: To configure static aggregation mode type with Destination MAC affects the distribution and Source MAC affects the distribution only. Switch# configure terminal Switch (config)# access-list rate-limiter pps 100 4.2.20 banner Command: banner c banner-text c, where 'c' is a delimiting character Default: N/A Usage Guide: To configure banner-text. Example: To configure banner-text with word “ddddd”.
PAGE 65
Command Guide 4.2.21 banner exec Command: banner login c banner-text c, where 'c' is a delimiting character Default: N/A Usage Guide: To configure login banner-text. Example: To configure login banner-text with word “wwwwwwwwww”. Switch# configure terminal Switch (config)# banner exec 1 Enter TEXT message. End with the character '1'. gggggg 1 Telnet 192.168.0.100: Username: admin Password: gggggg # 4.2.
PAGE 66
Command Guide Example: To configure login banner-text with word “wwwwwwwwww”. Switch# configure terminal Switch (config)# banner login 1 Enter TEXT message. End with the character '1'. wwwwwwwwww 1 Console: Press ENTER to get started wwwwwwwwww Username: admin Password: 4.2.23 banner motd Command: banner motd c banner-text c, where 'c' is a delimiting character Default: N/A Usage Guide: To configure motd banner-text. Example: To configure motd banner-text with word “ffffff”.
PAGE 67
Command Guide Console: ffffff Press ENTER to get started Username: 4.2.24 clock summer-time Command: clock summer-time date Default: N/A Usage Guide: To set daylight saving. Example: To set daylight saving (Started time: Feb, 3. 2013 8:8AM, End time: Dec, 31. 2013 8:8AM, Offset time: 60 minutes).
PAGE 68
Command Guide Usage Guide: To set timezone. Example: To set timezone (GMT -15) with profile 1. Switch# configure terminal Switch (config)# clock timezone 1 -15 4.2.26 default access-list rate-limiter Command: default access-list rate-limiter Rate limiter ID Default: 0 Usage Guide: To default the Rate limiter. Example: To default the Rate limiter ID 1. Switch# configure terminal Switch (config)# default access-list rate-limiter 1 4.2.
PAGE 69
Command Guide Switch# configure terminal Switch (config)# dot1x authentication timer inactivity 147 4.2.28 dot1x authentication timer re-authenticate Command: dot1x authentication timer re-authenticate <1-3600> Default: Re-authenticated Period: 3600 Usage Guide: To set the Re-authenticated Period for Network Access Server. Example: To set the Re-authenticated Period (777 seconds). Switch# configure terminal Switch (config)# dot1x authentication timer re-authenticate 777 4.2.
PAGE 70
Command Guide 4.2.30 dot1x guest-vlan Command: dot1x guest-vlan <1-4095> <1-4095> Guest VLAN ID used when entering the Guest VLAN. Default: 1 Usage Guide: To set the value of guest-vlan for Network Access Server Example: To set the value of guest-vlan(2) for Network Access Server Switch# configure terminal Switch (config)# dot1x guest-vlan 2 4.2.
PAGE 71
Command Guide 4.2.32 dot1x max-reauth-req Command: dot1x max-reauth-req <1-255> Default: 2 Usage Guide: To define 802.1X re-authentication frequency for Network Access Server Example: To define 802.1X re-authentication frequency with 78 times for Network Access Server Switch# configure terminal Switch (config)# dot1x max-reauth-req 78 4.2.33 dot1x system-auth-control Command: dot1x system-auth-control Default: Disable Usage Guide: To enable 802.
PAGE 72
Command Guide Default: 10 Usage Guide: To configure 802.1X hold time for Network Access Server Example: To configure 802.1X hold time(12 seconds) for Network Access Server Switch# configure terminal Switch (config)# dot1x timeout quiet-period 12 4.2.35 dot1x timeout tx-period Command: dot1x timeout tx-period <1-65535> tx-period The time between EAPOL retransmissions. Default: 30 Usage Guide: To configure 802.1X EPOAL timeout for Network Access Server Example: To configure 802.
PAGE 73
Command Guide Example: To configure enable password(admin) for user Switch# configure terminal Switch (config)# enable password admin Press ENTER to get started Username: Password: > enable Password: ***** # 4.2.37 enable password level Command: enable password level <1-15> <1-15> Level number The UNENCRYPTED (cleartext) password.
PAGE 74
Command Guide # 4.2.38 enable secret Command: enable secret 0 | 5 level <1-15> 0 Specifies an UNENCRYPTED password will follow 5 Specifies an ENCRYPTED secret will follow <1-15> Level number The UNENCRYPTED (cleartext) / ENCRYPTED(MD5) password.
PAGE 75
Command Guide 4.2.39 end Command: end Default: N/A Usage Guide: To level the configure terminal mode Example: To level the configure terminal mode Switch# configure terminal Switch (config)# end # 4.2.40 erps <1-64> guard Command: erps <1-64> guard <10-2000> <1-64> ERPS group number <10-2000> Guard time in ms Default: 500 Usage Guide: To configure the Guard Time for ERPS.
PAGE 76
Command Guide 4.2.41 erps <1-64> holdoff Command: erps <1-64> holdoff < 0-10000> <1-64> ERPS group number < 0-10000> Holdoff time in ms Default: 0 Usage Guide: To configure the Hold Off Time for ERPS Example: To configure the Hold Off Time (178 ms) for ERPS(Profile 1) Switch# configure terminal Switch (config)# erps 1 holdoff 900 4.2.
PAGE 77
Command Guide 4.2.43 erps <1-64> mep Command: erps <1-64> mep port0 sf aps port1 sf aps <1-64> ERPS group number Index of Port 0 SignalFail MEP Index of Port 0 APS MEP Index of Port 1 SignalFail MEP Index of Port 1 APS MEP Default: 0 Usage Guide: To configure ERPS Instance Data for specific ERPS profile. Example: To configure ERPS Instance Data(Port0: SF MEP = 2, APS MEP = 1.
PAGE 78
Command Guide 4.2.45 erps <1-64> rpl neighbor Command: erps <1-64> rpl neighbor { port0 | port1 } port0 ERPS Port 0 interface port1 ERPS Port 1 interface Default: N/A Usage Guide: To configure Ring Protection Link Neighbor Role for specific ERPS interface. Example: To configure Ring Protection Link Neighbor Role for specific ERPS interface.. Switch# configure terminal Switch (config)# erps 1 rpl neighbor port0 4.2.
PAGE 79
Command Guide 4.2.
PAGE 80
Command Guide Default: N/A Usage Guide: To configure topology change notification (TCN) propagation for the specific profile. Example: To configure topology change notification (TCN) propagation for the specific profile 1 Switch# configure terminal Switch (config)# erps 1 topology-change propagate 4.2.49 erps <1-64> topology-change propagate Command: erps <1-64> version 1 | 2 <1-64> ERPS group number version Version Default: V2 Usage Guide: To configure ERPS version number for the specific profile.
PAGE 81
Command Guide Default: V2 Usage Guide: To configure ERPS VLANs for the specific profile. Example: To configure ERPS VLANs(VLAN5 - VLAN8) for the specific profile 1. Switch# configure terminal Switch (config)# erps 1 vlan add 5-8 4.2.
PAGE 82
Command Guide Example: To configure Ethernet Virtual Circuits (EVC identifier: 1, EVC VLAN ID: 2, GigabitEthernet Port: 1/1, 1/2, Internal VLAN ID: 3, Disable learning, Policer ID: 4). Switch# configure terminal Switch (config)# evc 1 vid 2 interface GigabitEthernet 1/1-2 ivid 3 learning disable policer 4 4.2.
PAGE 83
Command Guide add Setup inner tag add properties.
PAGE 84
Command Guide disable No tag added when forwarding to UNI enable Add tag when forwarding to UNI pcp Setup added tag PCP Added tag PCP preserve Setup tag PCP/DEI preservation vid Setup added tag VLAN ID match Added tag VLAN ID Setup outer tag match properties policer Policer (ingress bandwith profile) Policer ID discard Map to policer discarding all frames evc Use policer setup for EVC none Map to policer allowing all frames poli
PAGE 85
Command Guide Switch# configure terminal Switch (config)# evc ece 1 direction both evc 2 frame-type ipv4 inner-tag add dei 1 pcp 4 preserve type s-custom-tag vid 5 interface GigabitEthernet 1/3 outer-tag add dei 0 mode enable pcp 2 vid 7 match dei any pcp any type c-tagged vid 6 policer 8 policy 9 pop 2 4.2.
PAGE 86
Command Guide direction ECE identifier Setup ECE direction both Bidirectional traffic flow nni-to-uni NNI-to-UNI traffic flow uni-to-nni UNI-to-NNI traffic flow evc EVC mapping EVC identifier none Map to no EVC ID frame-type Setup matched frame type any Match any frame type ipv4 Match IPv4 frames ipv6 Match IPv6 frames inner-tag Setup inner tag options add Setup inner tag add properties.
PAGE 87
Command Guide s-tagged Match S-tagged frames tagged Match tagged frames untagged Match untagged frames vid Setup matched VLAN ID Matched VLAN ID value/range any interface next Match any VLAN ID Setup UNI Setup the ECE ID of the next entry Select ECE ID of an existing entry last Make the ECE the last entry outer-tag add Setup outer tag options Setup outer tag add properties dei Setup added tag DEI mode Added tag DEI Setup NNI-to-UNI out
PAGE 88
Command Guide Usage Guide: To update EVC Control Entry for specific ECE profile. Example 1: To update “direction nni-to-uni” for ECE profile 1. Switch# configure terminal Switch (config)# evc ece 1 direction nni-to-uni 4.2.
PAGE 89
Command Guide Usage Guide: To configure a profile for EVC Policer (Ingress Bandwidth Profile) . Example: To configure EVC Policer (Ingress Bandwidth Profile) as tabled below. Switch# configure terminal Switch (config)# evc policer 1 enable cbs 20 cir 30 ebs 40 eir 50 mode aware rate-type data type mef 4.2.
PAGE 90
Command Guide Default: N/A Usage Guide: To update a profile for EVC Policer (Ingress Bandwidth Profile). Example: To update EVC Policer (Ingress Bandwidth Profile) with EIR 1000 for policer 1 Switch# configure terminal Switch (config)# evc policer update 1 eir 1000 4.2.
PAGE 91
Command Guide 4.2.57 exit Command: exit Default: N/A Usage Guide: To exit configure terminal mode. Example: To exit configure terminal mode. Switch# configure terminal Switch (config)# exit # 4.2.58 green-ethernet led interval Command: green-ethernet led interval <0~24> intensity <0-100> <0~24> Interval from 00.00 to 24.00 (00 is used to start at midnight, while 24 is used to stop at midnight). intensity <0-100> LEDs intensity.
PAGE 92
Command Guide Switch# configure terminal Switch (config)# green-ethernet led interval 8-13 intensity 80 4.2.59 green-ethernet led on-event Command: green-ethernet led on-event error | link-change <0-65535> error Set LEDs intensity to 100% if an error occurs. link-change Specifies how long to turn LEDs intensity into 100%, when a link changes state. <0-65535> Number of seconds to set LEDs intensity at 100% at link change.
PAGE 93
Command Guide Switch (config)# gvrp 4.2.61 gvrp max-vlans Command: gvrp max-vlans <1-4095> Default: 20 Usage Guide: To configure how many VLANs will be in GVRP. Example: To configure 200 VLANs in GVRP. Switch# configure terminal Switch (config)# gvrp max-vlans 200 4.2.62 gvrp time Command: gvrp time join-time leave-all-time leave-time join-time Set GARP protocol parameter JoinTime. See IEEE 802.1D-2004, clause 12.
PAGE 94
Command Guide Example: To configure Join-time, Leave-time, Leave all-time for GVRP as tabled below. Switch# configure terminal Switch (config)# gvrp time join-time 5 leave-all-time 1200 leave-time 150 4.2.63 help Command: help Default: N/A Usage Guide: To explain how to use commands. Example: To explain how to use commands. Switch# configure terminal Switch (config)# help Help may be requested at any point in a command by entering a question mark '?'.
PAGE 95
Command Guide 4.2.64 hostname Command: hostname < WORD > < WORD > This system's network name Default: N/A Usage Guide: To configure switch’s hostname. Example: To configure switch’s hostname with “planetbestswitch” Switch# configure terminal Switch (config)# hostname planetbestswitch planetbestswitch(config)# 4.2.
PAGE 96
Command Guide 4.2.65.1 access-list action permit Command: access-list action permit action Access list action Default: Permit Usage Guide: To configure Permit for the ACL action. Example: To configure Permit ACL action for the GigabitEthernet X/X. Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # access-list action permit 4.2.65.
PAGE 97
Command Guide 4.2.65.3 access-list logging Command: access-list logging logging Logging frame information. Note: The logging feature only works when the packet length is less than 1518 (without VLAN tags) and the System Log memory size and logging rate is limited. Default: Disable Usage Guide: To enable Logging function for the ACL. Example: To enable ACL Logging function for the GigabitEthernet X/X.
PAGE 98
Command Guide 4.2.65.5 access-list port-state Command: access-list port-state port-state Re-enable shutdown port that was shutdown by access-list module Default: Enable Usage Guide: To enable Port-state function for the ACL. Example: To configure ACL Port-state function for the GigabitEthernet X/X. Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # access-list port-state 4.2.65.
PAGE 99
Command Guide 4.2.65.7 access-list redirect interface Command: access-list redirect interface 10GigabitEthernet | GigabitEthernet redirect Redirect frame to specific port Default: Disable Usage Guide: To redirect frames to specific Port. Example: To redirect GigabitEthernet X/X frames to GigabitEthernet 1/2. Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # access-list redirect interface GigabitEthernet 1/2 4.2.65.
PAGE 100
Command Guide 4.2.65.9 aggregation group Command: aggregation group aggregation Create an aggregation group Create an aggregation group The aggregation group id Default: N/A Usage Guide: To configure aggregation group. Example: To configure aggregation group 7 for the GigabitEthernet X/X. Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # aggregation group 7 4.2.65.
PAGE 101
Command Guide 4.2.65.11 do Command: do < exec commands > do To run exec commands in config mode Default: N/A Usage Guide: To run exec commands in configure terminal mode Example: To run “show aaa” in configure terminal mode. Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # do show aaa console : local telnet ssh http : local : local : local 4.2.65.
PAGE 102
Command Guide 4.2.65.13 dot1x port-control Command: dot1x port-control auto | force-authorized | force-unauthorized | mac-based | multi | single dot1x IEEE Standard for port-based Network Access Control port-control Sets the port security state. auto Port-based 802.1X Authentication force-authorized Port access is allowed force-unauthorized Port access is not allowed mac-based Switch authenticates on behalf of the client multi Multiple Host 802.1X Authentication single Single Host 802.
PAGE 103
Command Guide Example: To enable RADIUS-assigned QoS for GigabitEthernet X/X. Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # dot1x radius-qos 4.2.65.15 dot1x radius-vlan Command: dot1x radius-vlan dot1x IEEE Standard for port-based Network Access Control radius-vlan Enables/disables per-port state of RADIUS-assigned VLAN. Default: Disable Usage Guide: To enable RADIUS-assigned VLAN for 802.
PAGE 104
Command Guide Example: To restart 802.1X authentication process for GigabitEthernet X/X. Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # dot1x re-authenticate 4.2.65.17 duplex Command: duplex auto | full | half duplex Interface duplex auto Auto negotiation of duplex mode. full Forced full duplex. half Forced half duplex. Default: Auto Usage Guide: To configure duplex mode for interface. Example: To configure auto duplex mode for GigabitEthernet X/X.
PAGE 105
Command Guide Usage Guide: To back to EXEC mode Example: To back to EXEC mode Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # end Switch# 4.2.65.19 evc dei Command: evc dei colored | fixed evc Ethernet Virtual Connections dei Setup DEI mode colored Allow policer to set DEI fixed Use classified DEI Default: Fixed Usage Guide: To configure EVC DEI mode Example: To configure EVC DEI mode (Colored) for GigabitEthernet X/X.
PAGE 106
Command Guide discard Discard L2CP frames Select BPDU addresses (0-15) and GARP addresses (16-31) Default: N/A Usage Guide: To configure policy ID of L2CP discard Example: To configure policy ID 1 of L2CP discard for GigabitEthernet X/X. Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # evc l2cp discard 1 4.2.65.
PAGE 107
Command Guide 4.2.65.22 evc l2cp peer(GG) Command: evc l2cp forward evc Ethernet Virtual Connections l2cp Setup L2CP forwarding peer Redirect L2CP frames to local protocol entity Select BPDU addresses (0-15) and GARP addresses (16-31) Default: N/A Usage Guide: To configure policy ID of L2CP peer Example: To configure policy 1 of L2CP peer for GigabitEthernet X/X.
PAGE 108
Command Guide Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # evc update dei colored 4.2.65.24 excessive-restart Command: excessive-restart excessive-restart Restart backoff algorithm after 16 collisions (No excessive-restart means discard frame after 16 collisions) Default: Discard Usage Guide: To enable Backoff Algorithm for the specific interface Example: To enable Backoff Algorithm for the GigabitEthernet X/X.
PAGE 109
Command Guide Example: To exit current mode. Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # exit Switch (config)# 4.2.65.26 flowcontrol Command: flowcontrol off | on flowcontrol Traffic flow control. off Disable flow control. on Enable flow control.
PAGE 110
Command Guide Usage Guide: To enable power saving for ports with no link partner Example: To enable power saving for ports with no link for GigabitEthernet X/X Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # green-ethernet energy-detect 4.2.65.28 green-ethernet short-reach(GG) Command: green-ethernet short-reach green-ethernet short-reach Green ethernet (Power reduction) Enable power saving for ports which is connect to link partner with short cable.
PAGE 111
Command Guide Usage Guide: To send GVRP Join-Request to specific interface Example: To send GVRP Join-Request(VLAN 1) to GigabitEthernet X/X Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # gvrp join-request vlan 1 4.2.65.
PAGE 112
Command Guide Default: Disable Usage Guide: To configure Check-VLAN mode into ARP inspection for specific interface Example: To configure Check-VLAN mode (Enabled) into ARP inspection for GigabitEthernet X/X Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # ip arp inspection check-vlan 4.2.65.
PAGE 113
Command Guide arp Address Resolution Protocol inspection ARP inspection trust ARP inspection trust config Default: Trusted Usage Guide: To configure Trusted into ARP inspection for specific interface Example: To configure Trusted into ARP inspection for GigabitEthernet X/X Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # ip arp inspection trust 4.2.65.
PAGE 114
Command Guide Default: N/A Usage Guide: To apply the IGMP Snooping filter ID for specific interface Example: To apply the IGMP Snooping filter ID 1 for GigabitEthernet X/X Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # ip igmp snooping filter 1 4.2.65.
PAGE 115
Command Guide Usage Guide: To limit maximum number of IGMP group for specific interface Example: To limit 5 groups of IGMP for GigabitEthernet X/X Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # ip igmp snooping max-groups 5 4.2.65.
PAGE 116
Command Guide Example: To enable IP Source Guard for GigabitEthernet X/X Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # ip verify source 4.2.65.
PAGE 117
Command Guide Usage Guide: To apply the MLD Snooping filter ID for specific interface Example: To apply the MLD Snooping filter ID 1 for GigabitEthernet X/X Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # ipv6 mld snooping filter 1 4.2.65.
PAGE 118
Command Guide Example: To limit 5 groups of MLD for GigabitEthernet X/X Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # ipv6 mld snooping max-groups 5 4.2.65.
PAGE 119
Command Guide Example: To enable LACP for GigabitEthernet X/X Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # lacp 4.2.65.
PAGE 120
Command Guide Usage Guide: To configure LACP port-priority for specific interface Example: To configure LACP port-priority (555) for GigabitEthernet X/X Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # lacp port-priority 555 4.2.65.
PAGE 121
Command Guide Default: Fast Usage Guide: To configure LACP timeout type for specific interface Example: To enable LACP timeout type (slow) for GigabitEthernet X/X Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # lacp timeout slow 4.2.65.
PAGE 122
Command Guide Default: N/A Usage Guide: To apply MED Media-VLAN policy of LLDP for specific interface Example: To apply MED Media-VLAN policy 2 of LLDPfor GigabitEthernet X/X Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # lldp med media-vlan policy-list 2 4.2.65.
PAGE 123
Command Guide 4.2.65.53 lldp receive Command: lldp receive lldp LLDP configurations receive Enable/Disable decoding of received LLDP frames. Default: Both (Tx +Rx) Usage Guide: To configure LLDP Rx only mode for specific interface Example: To configure LLDP Rx only mode for GigabitEthernet X/X Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # lldp receive 4.2.65.
PAGE 124
Command Guide 4.2.65.55 lldp tlv-select port-description Command: lldp tlv-select port-description lldp LLDP configurations tlv-select To transmit which optional TLVs. port-description Enable/Disable transmission of port description.
PAGE 125
Command Guide 4.2.65.57 lldp tlv-select system-description Command: lldp tlv-select system-description lldp LLDP configurations tlv-select To transmit which optional TLVs. system-description Enable/Disable transmission of system description.
PAGE 126
Command Guide 4.2.65.59 lldp transmit Command: lldp transmit lldp LLDP configurations transmit Enable/Disabled transmision of LLDP frames. Default: Both (Tx +Rx) Usage Guide: To configure LLDP Tx only mode for specific interface Example: To configure LLDP Tx only mode for GigabitEthernet X/X Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # lldp transmit 4.2.65.
PAGE 127
Command Guide 4.2.65.
PAGE 128
Command Guide 4.2.65.63 loop-protect tx-mode Command: loop-protect tx-mode loop-protect tx-mode Loop protection configuration Actively generate PDUs Default: Enabled Usage Guide: To enable tx-mode of Loop protection for specific interface Example: To enable tx-mode of Loop protection for GigabitEthernet X/X Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # loop-protect tx-mode 4.2.65.
PAGE 129
Command Guide Switch (config-if) # mac address-table learning 4.2.65.65 media-type Command: media-type dual | rj45 | sfp media-type Media type. dual Dual media interface (copper & fiber interface). rj45 rj45 interface (copper interface). sfp sfp interface (fiber interface).
PAGE 130
Command Guide Switch (config)# interface GigabitEthernet X/X Switch (config-if) # mtu 9000 4.2.65.
PAGE 131
Command Guide Example: To configure port role (source) of MVR profiles (111) for GigabitEthernet X/X Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # mvr name 111 type source 4.2.65.
PAGE 132
Command Guide Default: Disable Usage Guide: To enable SSM of SyncE for specific interface Example: To enable SSM of SyncE for GigabitEthernet X/X Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # network-clock synchronization ssm 4.2.65.71 no Command: no no Negate a command or set its defaults Default: N/A Usage Guide: To default the function for specific interface Example: To enable the function (network-clock synchronization ssm) for GigabitEthernet X/X.
PAGE 133
Command Guide Default is 56 (excluding MAC, IP and ICMP headers) Default: N/A Usage Guide: To run Ping function for specific interface Example: To run Ping function (IP address: 10.10.10.10 with size 88 bytes) for GigabitEthernet X/X. Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # ping ip 10.10.10.10 size 88 4.2.65.73 poe mode Command: poe mode { standard | plus } poe Power Over Ethernet. mode PoE mode.
PAGE 134
Command Guide 4.2.65.74 poe pdcheck IP Command: poe pdcheck IP poe Power Over Ethernet. pdcheck Allows user to enable or disable per port PD Alive Check function. IP To set PoE device IP address here for system making ping to the PoE device. Default: N/A Usage Guide: To configure Ping PD IP Address of PoE for specific interface Example: To configure Ping PD IP Address (10.101.10.10) of PoE for GigabitEthernet X/X.
PAGE 135
Command Guide Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # poe pdcheck action alarm 4.2.65.76 poe pdcheck enable Command: poe pdcheck enable poe Power Over Ethernet. pdcheck Allows user to enable or disable per port PD Alive Check function. enable PD alive check enable. Default: Disabled Usage Guide: To enable PD Ping Alive Check function of PoE for specific interface. Example: To enable PD Ping Alive Check function of PoE for GigabitEthernet X/X.
PAGE 136
Command Guide Usage Guide: To configure PD Ping Alive Check interval of PoE for specific interface. Example: To configure PD Ping Alive Check interval (100 seconds) of PoE for GigabitEthernet X/X. Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # poe pdcheck interval 100 4.2.65.78 poe pdcheck reboot-time Command: poe pdcheck reboot-time <30-180> poe Power Over Ethernet. pdcheck Allows user to enable or disable per port PD Alive Check function.
PAGE 137
Command Guide <1-5> retry-count <1-5> Default: 2 Usage Guide: To configure PD Ping Alive Check retry count of PoE for specific interface. Example: To configure PD Ping Alive Check retry count (5) of PoE for GigabitEthernet X/X. Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # poe pdcheck retry-count 5 4.2.65.80 poe power limit Command: poe power limit { } poe Power Over Ethernet.
PAGE 138
Command Guide priority Interface priority. critical Set priority to critical. high Set priority to high. low Set priority to low. Default: 2 Usage Guide: To configure interface priority of PoE for specific interface. Example: To configure interface priority (low) of PoE for GigabitEthernet X/X. Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # poe priority low 4.2.65.
PAGE 139
Command Guide 4.2.65.83 port-security Command: port-security port-security Enable/disable port security per interface. Default: Disabled Usage Guide: To enable Port-security for specific interface Example: To enable Port-security for GigabitEthernet X/X Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # port-security 4.2.65.
PAGE 140
Command Guide 4.2.65.85 port-security violation Command: port-security violation [protect | shutdown | trap | trap-shutdown] port-security violation Enable/disable port security per interface. The action involved with exceeding the limit.
PAGE 141
Command Guide Example: To configure protected mode (trap-shutdown) of Port-security for GigabitEthernet X/X Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # port-security violation trap-shutdown 4.2.65.87 pvlan Command: pvlan pvlan Private VLAN list of PVLANs. Range is from 1 to number of ports.
PAGE 142
Command Guide Example: To enable PVLAN isolation for GigabitEthernet X/X Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # pvlan isolation 4.2.65.
PAGE 143
Command Guide Usage Guide: To configure DEI of QoS for specific interface Example: To configure DEI (1) of QoS for GigabitEthernet X/X Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # qos dei 1 4.2.65.
PAGE 144
Command Guide Default: Disabled Usage Guide: To configure DSCP Classify of QoS for specific interface Example: To configure DSCP Classify (Any) of QoS for GigabitEthernet X/X Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # qos dscp-classify any 4.2.65.
PAGE 145
Command Guide dscp-translate DSCP ingress translation Default: Disabled Usage Guide: To configure DSCP ingress translation of QoS for specific interface Example: To configure DSCP ingress translation of QoS for GigabitEthernet X/X Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # qos dscp-translate 4.2.65.
PAGE 146
Command Guide Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # qos map cos-tag cos 1 dpl 1 pcp 6 dei 0 4.2.65.
PAGE 147
Command Guide 4.2.65.97 qos pcp Command: qos pcp qos Quality of Service pcp Priority Code Point configuration Specific Priority Code Point Default: 0 Usage Guide: To configure PCP of QoS for specific interface Example: To configure PCP (6) of QoS for GigabitEthernet X/X Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # qos pcp 6 4.2.65.
PAGE 148
Command Guide 4.2.65.
PAGE 149
Command Guide Example: To configure Egress Queue (4) Shapers Rate (9999 Kbps) of QoS for GigabitEthernet X/X Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # qos queue-shaper queue 4 9999 4.2.65.
PAGE 150
Command Guide Default: 500 Usage Guide: To configure Broadcast Frames Storm Control Rate of QoS for specific interface Example: To configure Broadcast Frames Storm Control Rate (999 fps) of QoS for GigabitEthernet X/X Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # qos storm broadcast 999 fps 4.2.65.
PAGE 151
Command Guide unknown Police unknown (flooded) frames fps Policer rate (default kbps) Rate is fps Default: 500 Usage Guide: To configure Unknown Frames Storm Control Rate of QoS for specific interface Example: To configure Unknown Frames Storm Control Rate (999 fps) of QoS for GigabitEthernet X/X Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # qos storm unicast 999 fps 4.2.65.
PAGE 152
Command Guide 4.2.65.106 qos tag-remark mapped Command: qos tag-remark mapped qos Quality of Service tag-remark Tag remarking configuration mapped Used mapped values (cos,dpl -> pcp,dei) Default: Classified Usage Guide: To enable Tag-remark mapped mode of QoS for specific interface Example: To enable Tag-remark mapped mode of QoS for GigabitEthernet X/X Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # qos tag-remark mapped 4.2.65.
PAGE 153
Command Guide 4.2.65.108 qos trust tag Command: qos trust tag qos Quality of Service trust Trust configuration tag VLAN tag Default: Disabled Usage Guide: To enable VLAN tag Classification of QoS for specific interface Example: To enable VLAN tag Classification of QoS for GigabitEthernet X/X Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # qos trust tag 4.2.65.
PAGE 154
Command Guide Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # rmon collection history 1 buckets 5 interval 3 4.2.65.
PAGE 155
Command Guide Default: No shutdown Usage Guide: To shut down specific interface Example: To shut down GigabitEthernet X/X Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # shutdown 4.2.65.
PAGE 156
Command Guide Default: Enabled Usage Guide: To enable Auto Edge of CIST Normal Port Configuration for specific interface Example: To enable Auto Edge of CIST Normal Port Configuration for GigabitEthernet X/X Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # spanning-tree auto-edge 4.2.65.
PAGE 157
Command Guide Default: Non-Edge Usage Guide: To enable edge port of CIST Normal Port Configuration for specific interface Example: To enable edge port of CIST Normal Port Configuration for GigabitEthernet X/X Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # spanning-tree edge 4.2.65.
PAGE 158
Command Guide 4.2.65.117 spanning-tree mst cost Command: spanning-tree mst cost | auto spanning-tree Spanning Tree protocol mst STP bridge instance instance cost 0-7 (CIST=0, MST2=1...
PAGE 159
Command Guide Example: To enable Path Cost (32) of CIST / MST Normal Port Configuration (CIST) for GigabitEthernet X/X Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # spanning-tree mst 0 port-priority 32 4.2.65.
PAGE 160
Command Guide Example: To enable Restrict topology change notifications of CIST Normal Port Configuration for GigabitEthernet X/X Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # spanning-tree restricted-tcn 4.2.65.121 speed Command: speed [10 | 100 | 1000 | 10g | auto] speed Configures interface speed. If you use 10, 100, or 1000 keywords with the auto keyword the port will only advertise the specified speeds.
PAGE 161
Command Guide vlan Set VLAN when interface is in access mode VLAN ID of the VLAN when this port is in access mode Default: 1 Usage Guide: To configure access VLAN ID for specific interface Example: To configure access VLAN ID (5) for GigabitEthernet X/X Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # switchport access vlan 5 4.2.65.
PAGE 162
Command Guide 4.2.65.124 switchport forbidden vlan remove Command: switchport forbidden vlan remove switchport Switching mode characteristics forbidden Adds or removes forbidden VLANs from the current list of forbidden VLANs vlan Add or modify VLAN entry in forbidden table. remove Remove from existing list.
PAGE 163
Command Guide Example: To configure acceptable-frame-type (tagged) of Hybrid VLAN for GigabitEthernet X/X Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # switchport hybrid acceptable-frame-type tagged 4.2.65.
PAGE 164
Command Guide switchport hybrid Change PVID for hybrid port egress-tag all Switching mode characteristics Egress VLAN tagging configuration Tag all frames none No egress tagging except-native Tag all frames except frames classified to native VLAN of the hybrid port Default: Untagged Port VLAN Usage Guide: To configure Egress Tagging VLAN mode for specific interface Example: To configure Egress Tagging VLAN mode (None) for GigabitEthernet X/X Switch# configure terminal Switch (config)# interface G
PAGE 165
Command Guide 4.2.65.
PAGE 166
Command Guide Example: To enable Port type (Unaware) in Hybrid VLAN mode for GigabitEthernet X/X Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # switchport hybrid port-type unaware 4.2.65.
PAGE 167
Command Guide ip-subnet id VCL IP Subnet-based VLAN configuration. id keyword <1-128> Unique VCE ID for each VCL entry (1-128) vlan Source IP address and mask (Format: xx.xx.xx.xx/mm.mm.mm.mm).
PAGE 168
Command Guide Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # switchport vlan mac 00:55:44:33:22:11 vlan 5 4.2.65.134 switchport vlan mapping Command: switchport vlan mapping switchport vlan Switching mode characteristics VLAN commands mapping Maps an interface to a VLAN translation group.
PAGE 169
Command Guide vlan Group Name (Range: 1 - 16 characters) vlan keyword VLAN ID required for the group to VLAN mapping (Range: 1-4095) Default: None Usage Guide: To configure VLAN protocol group for specific interface Example: To configure VLAN protocol group as tabled below for GigabitEthernet X/X Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # switchport vlan protocol group 8081 vlan 5 4.2.65.
PAGE 170
Command Guide 4.2.65.
PAGE 171
Command Guide Example: To enable Voice VLAN security for GigabitEthernet X/X Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # switchport voice vlan security 4.2.66 interface vlan Command: interface vlan vlan VLAN interface configurations List of VLAN interface numbers, 1~4095 Default: N/A Usage Guide: To enter the VLAN interface mode.
PAGE 172
Command Guide Switch# configure terminal Switch (config)# interface vlan X Switch (config-if-vlan)# do show aaa console : local telnet : local ssh : local http : local 4.2.66.2 end Command: end end Go back to EXEC mode Default: Auto Usage Guide: To back to EXEC mode Example: To back to EXEC mode Switch# configure terminal Switch (config)# interface vlan X Switch (config-if-vlan)# end Switch# 4.2.66.
PAGE 173
Command Guide Example: To exit current mode. Switch# configure terminal Switch (config)# interface vlan X Switch (config-if-vlan)# exit Switch (config)# 4.2.66.4 ip address Command: ip address ip Interface Internet Protocol config commands address Address configuraton IP address IP netmask Default: None Usage Guide: To configure IP address mode for specific VLAN Example: To configure IP address mode (192.168.1.
PAGE 174
Command Guide Default: None Usage Guide: To configure IP address mode for specific VLAN Example: To configure IP address mode (DHCP) for VLAN X Switch# configure terminal Switch (config)# interface vlan X Switch (config-if-vlan)# ip address dhcp 4.2.66.
PAGE 175
Command Guide server Enable DHCP server per VLAN Default: None Usage Guide: To enable IPv4 DHCP Server for specific VLAN Example: To enable IPv4 DHCP Server for VLAN X Switch# configure terminal Switch (config)# interface vlan X Switch (config-if-vlan)# ip dhcp server 4.2.66.
PAGE 176
Command Guide 4.2.66.
PAGE 177
Command Guide Usage Guide: To configure Last-member-query-interval of IGMP snooping for specific VLAN Example: To configure Last-member-query-interval (100 seconds) of IGMP snooping for VLAN X Switch# configure terminal Switch (config)# interface vlan X Switch (config-if-vlan)# ip igmp snooping last-member-query-interval 1000 4.2.66.
PAGE 178
Command Guide snooping Snooping IGMP querier IGMP Querier configuration address IGMP Querier address configuration A valid IPv4 unicast address Default: 0.0.0.0 Usage Guide: To configure Querier address of IGMP snooping for specific VLAN Example: To configure Querier address (192.168.1.15) of IGMP snooping for VLAN X Switch# configure terminal Switch (config)# interface vlan X Switch (config-if-vlan)# ip igmp snooping querier address 192.168.1.15 4.2.66.
PAGE 179
Command Guide 4.2.66.
PAGE 180
Command Guide Switch# configure terminal Switch (config)# interface vlan X Switch (config-if-vlan)# ip igmp snooping query-max-response-time 600 4.2.66.
PAGE 181
Command Guide Default: 1 Usage Guide: To configure Unsolicited-Report-Interval of IGMP snooping for specific VLAN Example: To configure Unsolicited-Report-Interval (99 seconds) of IGMP snooping for VLAN X Switch# configure terminal Switch (config)# interface vlan X Switch (config-if-vlan)# ip igmp snooping unsolicited-report-interval 99 4.2.66.
PAGE 182
Command Guide Default: Disabled Usage Guide: To enable MLD snooping for specific VLAN Example: To enable MLD snooping for VLAN X Switch# configure terminal Switch (config)# interface vlan X Switch (config-if-vlan)# ipv6 mld snooping 4.2.66.
PAGE 183
Command Guide 4.2.66.
PAGE 184
Command Guide Switch# configure terminal Switch (config)# interface vlan X Switch (config-if-vlan)# ipv6 mld snooping priority 5 4.2.66.
PAGE 185
Command Guide Default: 125 Usage Guide: To configure Querier-interval of MLD snooping for specific VLAN Example: To configure Querier-interval (600 seconds) of MLD snooping for VLAN X Switch# configure terminal Switch (config)# interface vlan X Switch (config-if-vlan)# ipv6 mld snooping query-interval 600 4.2.66.
PAGE 186
Command Guide mld Multicast Listener Discovery snooping Snooping MLD robustness-variable Robustness Variable Packet loss tolerance count from 1 to 255 Default: 2 Usage Guide: To configure Robustness Variable of MLD snooping for specific VLAN Example: To configure Robustness Variable (88) of MLD snooping for VLAN X Switch# configure terminal Switch (config)# interface vlan X Switch (config-if-vlan)# ipv6 mld snooping robustness-variable 88 4.2.66.
PAGE 187
Command Guide 4.2.66.28 no Command: no no Negate a command or set its defaults Default: N/A Usage Guide: To default the function for specific interface Example: To disable the function (ip address dhcp) for VLAN X Switch# configure terminal Switch (config)# interface vlan X Switch (config-if-vlan)# no ip address dhcp 4.2.
PAGE 188
Command Guide 4.2.
PAGE 189
Command Guide Default: N/A Usage Guide: To translate dynamic entries into static ARP inspection table. Example: To translate dynamic entries into static ARP inspection table. Switch# configure terminal Switch (config)# ip arp inspection translate ARP Inspection: Translate 1 dynamic entries into static entries. 4.2.
PAGE 190
Command Guide 4.2.71 ip arp inspection vlan Command: ip arp inspection vlan logging all | deny | permit ip Internet Protocol arp Address Resolution Protocol inspection ARP inspection vlan arp inspection vlan setting logging all arp inspection vlan list ARP inspection vlan logging mode config log all entries deny log denied entries permit log permitted entries Default: N/A Usage Guide: To configure VLAN mode of ARP inspection.
PAGE 191
Command Guide Usage Guide: To configure excluded IP range of DHCP Server. Example: To configure excluded IP range (192.168.0.100~192.168.0.101) of DHCP Server. Switch# configure terminal Switch (config)# ip dhcp excluded-address 192.168.0.100 192.168.0.101 4.2.73 ip dhcp pool Command: ip dhcp pool ip Internet Protocol dhcp Dynamic Host Configuration Protocol pool Configure DHCP address pools Pool name in 32 characters Default: N/A Usage Guide: To create a DHCP pool.
PAGE 192
Command Guide Default: None Usage Guide: To configure Broadcast IP address (DHCP option 28) of DHCP Server Example: To configure Broadcast IP address (192.168.0.66) of DHCP Server for pool “planetbestswitch” Switch# configure terminal Switch (config)# ip dhcp pool planetbestswitch Switch (config-dhcp-pool)# broadcast 192.168.0.66 4.2.73.
PAGE 193
Command Guide Default: None Usage Guide: To configure Bind IP to MAC of DHCP Server Example: To configure Bind IP to MAC (00:11:22:33:44:55) of DHCP Server for pool “planetbestswitch” Switch# configure terminal Switch (config)# ip dhcp pool planetbestswitch Switch (config-dhcp-pool)# client-identifier mac-address 00:11:22:33:44:55 4.2.73.
PAGE 194
Command Guide Usage Guide: To configure Default Gateway of DHCP Server Example: To configure Default Gateway (192.168.0.1) of DHCP Server for pool “planetbestswitch” Switch# configure terminal Switch (config)# ip dhcp pool planetbestswitch Switch (config-dhcp-pool)# default-router 192.168.0.1 4.2.73.6 dns-server Command: dns-server dns-server DNS servers Server's IP address Default: None Usage Guide: To configure DNS Server of DHCP Server Example: To configure DNS Server (168.95.1.
PAGE 195
Command Guide Example: To run “show aaa”. Switch# configure terminal Switch (config)# ip dhcp pool planetbestswitch Switch (config-dhcp-pool)# do show aaa console : local telnet ssh http : local : local : local 4.2.73.8 domain-name Command: domain-name domain-name Domain name Domain name Default: None Usage Guide: To configure Domain Name of DHCP Server Example: To configure Domain Name (planet.
PAGE 196
Command Guide Usage Guide: To back to EXEC mode Example: To back to EXEC mode Switch# configure terminal Switch (config)# ip dhcp pool planetbestswitch Switch (config-dhcp-pool)# end Switch# 4.2.73.10 exit Command: exit exit Exit from current mode Default: None Usage Guide: To exit current mode Example: To exit current mode. Switch# configure terminal Switch (config)# ip dhcp pool planetbestswitch Switch (config-dhcp-pool)# exit Switch (config)# 4.2.73.
PAGE 197
Command Guide Default: None Usage Guide: To configure MAC address of DHCP Server while the pool is in the host type. Example: To configure MAC address (00:11:22:33:44:55) of DHCP Server for pool “planetbestswitch” while the pool is in the host type. Switch# configure terminal Switch (config)# ip dhcp pool planetbestswitch Switch (config-dhcp-pool)# hardware-address 00:11:22:33:44:55 4.2.73.12 host Command: host host Client IP address and mask
PAGE 198
Command Guide <0-23> Hours <0-59> Minutes infinite Infinite lease Default: 1 day Usage Guide: To configure Lease Time of DHCP Server. Example: To configure Lease Time (119 minutes) of DHCP Server for pool “planetbestswitch”. Switch# configure terminal Switch (config)# ip dhcp pool planetbestswitch Switch (config-dhcp-pool)# lease 0 1 59 4.2.73.14 netbios-name-server Command: netbios-name-server netbios-name-server
PAGE 199
Command Guide b-node Broadcast node h-node Hybrid node m-node Mixed node p-node Peer-to-peer node Default: None Usage Guide: To configure NetBIOS node type of DHCP Server. Example: To configure NetBIOS node type (B-node) of DHCP Server for pool “planetbestswitch”. Switch# configure terminal Switch (config)# ip dhcp pool planetbestswitch Switch (config-dhcp-pool)# netbios-node-type b-node 4.2.73.
PAGE 200
Command Guide network Network number and mask Network number Network mask in dotted-decimal notation, excluding 255.255.255.255 Default: None Usage Guide: To configure Network IP address of DHCP Server. Example: To configure Network IP address (192.168.1.11/24) of DHCP Server for pool “planetbestswitch”. Switch# configure terminal Switch (config)# ip dhcp pool planetbestswitch Switch (config-dhcp-pool)# network 192.168.0.11 255.255.255.0 4.2.73.
PAGE 201
Command Guide nis-server Network information servers Server's IP address Default: None Usage Guide: To configure NIS Server of DHCP Server Example: To configure NIS Server (1.1.1.1) of DHCP Server for pool “planetbestswitch” Switch# configure terminal Switch (config)# ip dhcp pool planetbestswitch Switch (config-dhcp-pool)# nis-server 1.1.1.1 4.2.73.
PAGE 202
Command Guide Server's IP address Default: None Usage Guide: To configure NTP Server of DHCP Server Example: To configure NTP Server (1.1.1.1) of DHCP Server for pool “planetbestswitch” Switch# configure terminal Switch (config)# ip dhcp pool planetbestswitch Switch (config-dhcp-pool)# ntp-server 1.1.1.1 4.2.73.
PAGE 203
Command Guide 4.2.74 ip dns proxy Command: ip dns proxy ip Internet Protocol dns Domain Name System proxy DNS proxy service Default: Disabled Usage Guide: To enable DNS proxy. Example: To enable DNS proxy. Switch# configure terminal Switch (config)# ip dns proxy 4.2.
PAGE 204
Command Guide 4.2.76 ip http secure-redirect Command: ip http secure-redirect ip Internet Protocol http Hypertext Transfer Protocol secure-redirect Secure HTTP web redirection Default: Disabled Usage Guide: To redirect WebUI from HTTP to HTTPs Example: To redirect WebUI from HTTP to HTTPs Switch# configure terminal Switch (config)# ip http secure-redirect 4.2.
PAGE 205
Command Guide 4.2.78 ip igmp host-proxy Command: ip igmp host-proxy ip Internet Protocol igmp Internet Group Management Protocol host-proxy IGMP proxy configuration Default: Disabled Usage Guide: To enable IGMP Proxy Example: To enable IGMP Proxy. Switch# configure terminal Switch (config)# ip igmp host-proxy 4.2.
PAGE 206
Command Guide 4.2.80 ip igmp snooping Command: ip igmp snooping ip Internet Protocol igmp Internet Group Management Protocol snooping Snooping IGMP Default: Disabled Usage Guide: To enable IGMP Snooping. Example: To enable IGMP Snooping. Switch# configure terminal Switch (config)# ip igmp snooping 4.2.
PAGE 207
Command Guide Switch (config)# ip igmp snooping vlan 1 4.2.82 ip igmp ssm-range Command: ip igmp ssm-range ip Internet Protocol igmp Internet Group Management Protocol ssm-range IPv4 address range of Source Specific Multicast Valid IPv4 multicast address VLAN identifier(s): VID Prefix length ranges from 4 to 32 Default: 232.0.0.0/8 Usage Guide: To enable SSM Range of IGMP.
PAGE 208
Command Guide Example: To flood unregistered IPv4 multicast traffic. Switch# configure terminal Switch (config)# ip igmp unknown-flooding 4.2.84 ip name-server Command: ip name-server ip Internet Protocol name-server Domain Name System A valid IPv4 unicast address Default: Enabled Usage Guide: To configure DNS server IP address. Example: To configure DNS server IP address (8.8.8.8). Switch# configure terminal Switch (config)# ip name-server 8.8.8.8 4.2.
PAGE 209
Command Guide Switch# configure terminal Switch (config)# ip name-server 8.8.8.8 4.2.86 ip name-server dhcp interface vlan Command: ip name-server dhcp interface vlan ip Internet Protocol name-server dhcp vlan Domain Name System Dynamic Host Configuration Protocol VLAN Interface VLAN identifier(s): VID Default: None Usage Guide: To configure DNS IP address via specific VLAN DHCP Server. Example: To configure DNS IP address via specific VLAN 5 DHCP Server.
PAGE 210
Command Guide Example: To configure static route as below table. Switch# configure terminal Switch (config)# ip route 192.168.1.0 255.255.255.0 192.168.0.1 4.2.88 ip routing Command: ip routing ip Internet Protocol routing Enable routing for IPv4 and IPv6 Default: None Usage Guide: To enable IP routing Example: To enable IP routing Switch# configure terminal Switch (config)# ip routing 4.2.
PAGE 211
Command Guide Select an IP Address to configure Select a subnet mask to configure Default: None Usage Guide: To enable Static IP Source Guard Table for specific interface Example: To enable Static IP Source Guard Table as below table for GigabitEthernet 1/1 Switch# configure terminal Switch (config)# ip source binding interface GigabitEthernet 1/1 1 192.168.0.77 255.255.255.255 4.2.
PAGE 212
Command Guide 4.2.91 ip verify source Command: ip verify source ip Internet Protocol verify verify command source verify source Default: Disabled Usage Guide: To enable IP Source Guard Example: To enable IP Source Guard Switch# configure terminal Switch (config)# ip verify source 4.2.
PAGE 213
Command Guide 4.2.93 ipmc profile Command: ipmc profile ipmc IPv4/IPv6 multicast configuration profile IPMC profile configuration Default: Disabled Usage Guide: To enable IPMC profile Example: To enable IPMC profile Switch# configure terminal Switch (config)# ipmc profile 4.2.
PAGE 214
Command Guide 4.2.94.1 default range Command: default range default Set a command to its defaults range A range of IPv4/IPv6 multicast addresses for the profile Range entry name Default: None Usage Guide: To default IPMC Profile Rule for specific IPMC Profile Example: To default IPMC Profile Rule (Entry 1) for specific IPMC Profile (planet) Switch# configure terminal Switch (config)# ipmc profile planet Switch (config-ipmc-profile)# default range 1 4.2.94.
PAGE 215
Command Guide 4.2.94.3 do Command: do < exec commands > do To run exec commands in config mode Default: N/A Usage Guide: To run exec commands Example: To run “show aaa”. Switch# configure terminal Switch (config)# ipmc profile planet Switch (config-ipmc-profile)# do show aaa console : local telnet : local ssh : local http : local 4.2.94.
PAGE 216
Command Guide 4.2.94.5 exit Command: exit exit Exit from current mode Default: None Usage Guide: To exit current mode Example: To exit current mode. Switch# configure terminal Switch (config)# ipmc profile planet Switch (config-ipmc-profile)# exit Switch (config)# 4.2.94.6 no Command: no no Negate a command or set its defaults Default: N/A Usage Guide: To default the function. Example: To enable the function (description 999).
PAGE 217
Command Guide 4.2.94.
PAGE 218
Command Guide 4.2.96 ipv6 mld host-proxy leave-proxy Command: ipv6 mld host-proxy leave-proxy ipv6 IPv6 configuration commands mld Multicast Listener Discovery host-proxy MLD proxy configuration leave-proxy MLD proxy for leave configuration Default: Disabled Usage Guide: To enable MLD leave-proxy Example: To enable MLD leave-proxy. Switch# configure terminal Switch (config)# ipv6 mld host-proxy leave-proxy 4.2.
PAGE 219
Command Guide 4.2.98 ipv6 mld snooping vlan Command: ipv6 mld snooping vlan ipv6 IPv6 configuration commands mld Multicast Listener Discovery snooping vlan Snooping MLD MLD VLAN VLAN identifier(s): VID Default: Disabled Usage Guide: To enable MLD Snooping for specific VLAN. Example: To enable MLD Snooping for VLAN 1. Switch# configure terminal Switch (config)# ipv6 mld snooping vlan 1 4.2.
PAGE 220
Command Guide 4.2.100 ipv6 mld unknown-flooding Command: ipv6 mld unknown-flooding ipv6 IPv6 configuration commands mld Multicast Listener Discovery unknown-flooding Flooding unregistered IPv6 multicast traffic Default: Enabled Usage Guide: To flood unregistered IPv6 multicast traffic. Example: To flood unregistered IPv6 multicast traffic. Switch# configure terminal Switch (config)# ipv6 mld unknown-flooding 4.2.
PAGE 221
Command Guide Switch# configure terminal Switch (config)# ipv6 route 2001::7788/128 2002::1 Example 2: To configure static route as below table for IPv6. Switch# configure terminal Switch (config)# ipv6 route 2001::7788/128 interface vlan 1 fe80::1 4.2.102 lacp system-priority Command: lacp system-priority <1-65535> lacp LACP settings system-priority <1-65535> System priority Priority value, lower means higher priority Default: 32768 Usage Guide: To configure LACP system-priority.
PAGE 222
Command Guide 4.2.103 line Command: line { <0~16> | console 0 | vty <0~15> } line Configure a terminal line <0~16> List of line numbers console Console terminal line vty Virtual terminal Default: N/A Usage Guide: To enter line mode Example: To enter line mode (vty 1) Switch# configure terminal Switch (config)# line vty 1 Switch (config-line)# 4.2.103.1 do Command: do < exec commands > do To run exec commands. Default: N/A Usage Guide: To run exec commands. Example: To run “show aaa”.
PAGE 223
Command Guide telnet ssh http : local : local : local 4.2.103.2 editing Command: editing editing Enable command line editing Default: Enabled Usage Guide: To allow user editing command line. Example: To allow user editing command line. Switch# configure terminal Switch (config)# line vty 1 Switch (config-line)# editing 4.2.103.
PAGE 224
Command Guide Switch (config-line)#end Switch# 4.2.103.4 exec-banner Command: exec-banner exec-banner Enable the display of the EXEC banner Default: Enabled Usage Guide: To enable the display of the EXEC banner Example: To enable the display of the EXEC banner Switch# configure terminal Switch (config)# line vty 1 Switch (config-line)# exec-banner 4.2.103.
PAGE 225
Command Guide 4.2.103.6 exec-timeout Command: exec-timeout <0-1440> exec-timeout <0-1440> Set the EXEC timeout Timeout in minutes Default: N/A Usage Guide: To configure EXEC timeout Example: To configure EXEC timeout (10 minutes) Switch# configure terminal Switch (config)# line vty 1 Switch (config-line)# exec-timeout 10 4.2.103.7 exit Command: exit exit Exit from current mode Default: None Usage Guide: To exit current mode Example: To exit current mode.
PAGE 226
Command Guide 4.2.103.8 history size Command: history size <0-32> history size Control the command history function Set history buffer size <0-32> Number of history commands, 0 means disable Default: None Usage Guide: To exit current mode Example: To exit current mode. Switch# configure terminal Switch (config)# line vty 1 Switch (config-line)# history size 1 4.2.103.
PAGE 227
Command Guide 4.2.103.10 location Command: location location Enter terminal location description One text line describing the terminal's location Default: None Usage Guide: To configure description of location. Example: To configure description (taiwan) of location. Switch# configure terminal Switch (config)# line vty 1 Switch (config-line)# location taiwan 4.2.103.
PAGE 228
Command Guide 4.2.103.12 no Command: no no Negate a command or set its defaults Default: N/A Usage Guide: To default the function Example: To disable the function (motd-banner) for vty 1 Switch# configure terminal Switch (config)# line vty 1 Switch (config-line)# no motd-banner 4.2.103.
PAGE 229
Command Guide 4.2.103.14 width Command: width <0 or 40-512> width Set width of the display terminal <0 or 40-512> Number of characters on a screen line (0 for unlimited width) Default: 0 Usage Guide: To configure width of the display terminal. Example: To configure width (50) of the display terminal for vty 1. Switch# configure terminal Switch (config)# line vty 1 Switch (config-line)# width 50 4.2.104 lldp holdtime Command: lldp holdtime <2-10> lldp LLDP configurations.
PAGE 230
Command Guide 4.2.105 lldp med datum Command: lldp med datum nad83-mllw | nad83-navd88 | wgs84 lldp LLDP configurations. med Media Endpoint Discovery datum Datum (geodetic system) type nad83-mllw Mean lower low water datum 1983 nad83-navd88 North American vertical datum 1983 wgs84 World Geodetic System 1984 Default: WGS84 Usage Guide: To configure Datum type of LLDP Example: To configure Datum type (nad83-mllw) of LLDP Switch# configure terminal Switch (config)# lldp med datum nad83-mllw 4.2.
PAGE 231
Command Guide 4.2.107 lldp med location-tlv altitude Command: lldp med location-tlv altitude [floors ] | [meters ] lldp LLDP configurations. med Media Endpoint Discovery location-tlv altitude floors LLDP-MED Location Type Length Value parameter Altitude parameter Specify the altitude in floor. meters Altitude value. Specify the altitude in meters.
PAGE 232
Command Guide Switch# configure terminal Switch (config)# lldp med location-tlv elin-addr 911 4.2.109 lldp med location-tlv latitude Command: lldp med location-tlv latitude north | south lldp LLDP configurations. med Media Endpoint Discovery location-tlv LLDP-MED Location Type Length Value parameter latitude Latitude parameter north Setting latitude direction to north. south Setting latitude direction to south Latitude degrees (0.0000-90.
PAGE 233
Command Guide Default: North, 0 Usage Guide: To configure longitude direction of LLDP-MED Example: To configure longitude direction (east, 5) of LLDP-MED Switch# configure terminal Switch (config)# lldp med location-tlv longitude east 5 4.2.
PAGE 234
Command Guide Example: To configure media-VLAN-policy as below table of LLDP-MED Switch# configure terminal Switch (config)# lldp med media-vlan-policy 1 guest-voice tagged 1 dscp 45 l2-priority 5 4.2.112 lldp reinit Command: lldp reinit <1-10> lldp LLDP configurations. reinit LLDP tx reinitialization delay in seconds <1-10> 1-10 seconds.
PAGE 235
Command Guide 4.2.113 lldp timer Command: lldp timer <5-32768> lldp LLDP configurations. timer Sets LLDP TX interval (The time between each LLDP frame transmitted in seconds) <5-32768> 5-32768 seconds. Default: 30 Usage Guide: To configure Tx interval time of LLDP Example: To configure Tx interval time (555) of LLDP Switch# configure terminal Switch (config)# lldp timer 555 4.2.114 lldp transmission-delay Command: lldp transmission-delay <1-8192> lldp LLDP configurations.
PAGE 236
Command Guide 4.2.115 logging host Command: logging host | logging Syslog host host Domain name of the log server IP address of the log server Default: 0 Usage Guide: To configure address of log server Example: To configure address of log server Switch# configure terminal Switch (config)# logging host 192.168.5.5 4.2.
PAGE 237
Command Guide 4.2.117 logging on Command: logging on logging on Syslog Enable syslog server Default: Disabled Usage Guide: To enable log server Example: To enable log server Switch# configure terminal Switch (config)# logging on 4.2.
PAGE 238
Command Guide 4.2.119 loop-protect shutdown-time Command: loop-protect shutdown-time <0-604800> loop-protect Loop protection configuration shutdown-time Loop protection shutdown time interval <0-604800> Shutdown time in second Default: 180 Usage Guide: To configure shutdown time interval of Loop Protection Example: To configure shutdown time interval (888) of Loop Protection Switch# configure terminal Switch (config)# loop-protect shutdown-time 888 4.2.
PAGE 239
Command Guide 4.2.121 mac address-table aging-time Command: mac address-table aging-time <0,10-1000000> mac MAC table entries/configuration address-table MAC table entries/configuration <0,10-1000000> Aging time in seconds, 0 disables aging Default: 300 Usage Guide: To configure Aging Time of MAC Address Table Example: To configure Aging Time (888) of MAC Address Table Switch# configure terminal Switch (config)# mac address-table aging-time 888 4.2.
PAGE 240
Command Guide Example: To configure Static MAC Address Table as below table Switch# configure terminal Switch (config)# mac address-table static 00:11:22:33:44:55 vlan 1 interface GigabitEthernet 1/1 4.2.123 mep ais Command: mep ais [ fr1m | fr1s ] [ protect ] mep Maintenance Entity Point The MEP instance number. ais Alarm Indication Signal fr1m Frame rate is 1 f/min. fr1s Frame rate is 1 f/s. protect The AIS can be used for protection.
PAGE 241
Command Guide 4.2.124 mep aps Command: mep aps [ multi | uni ] { laps | { raps [ octet ] } } mep Maintenance Entity Point The MEP instance number. aps Automatic Protection Switching protocol laps Linear Automatic Protection Switching protocol. multi OAM PDU is transmitted with multicast MAC. Must me 'multi' in case of RAPS. uni OAM PDU is transmitted with unicast MAC. The MAC is taken from peer MEP MAC database. Only possible in case of LAPS.
PAGE 242
Command Guide fr10s Frame rate is 10 f/s. fr1m Frame rate is 1 f/min. fr1s Frame rate is 1 f/s. fr300s Frame rate is 300 f/s. fr6h Frame rate is 6 f/hour. fr6m Frame rate is 6 f/min. Default: Usage Guide: To configure CC of MEP Example: To configure CC of MEP 1 as below table Switch# configure terminal Switch (config)# mep 1 cc 2 fr10s 4.2.
PAGE 243
Command Guide Switch# configure terminal Switch (config)# mep 1 client domain evc 4.2.127 mep client flow Command: mep client flow level [ ais-prio [ | ais-highest ] ] [ lck-prio [ | lck-highest ] ] mep Maintenance Entity Point level The MEP instance number.
PAGE 244
Command Guide 4.2.128 mep dm Command: mep dm [ multi | { uni mep-id } ] [ single | dual ] [ rdtrp | flow ] interval last-n mep Maintenance Entity Point The MEP instance number. dm Delay Measurement Priority in case of tagged OAM. In the EVC domain this is the COS-ID dual Delay Measurement based on 1DM PDU transmission. flow The two way delay is calculated as round trip symmetrical flow delay.
PAGE 245
Command Guide 4.2.129 mep dm ns Command: mep dm ns mep Maintenance Entity Point The MEP instance number. dm Delay Measurement ns Nano Seconds Default: us Usage Guide: To configure Delay Measurement of MEP Example: To configure Delay Measurement unit (ns) of MEP 1 as below table. Switch# configure terminal Switch (config)# mep 1 dm ns 4.2.
PAGE 246
Command Guide Example: To reset Delay Measurement of MEP 1 while overflowing Switch# configure terminal Switch (config)# mep 1 dm overflow-reset 4.2.131 mep dm proprietary Command: mep dm proprietary mep Maintenance Entity Point dm The MEP instance number. Delay Measurement proprietary Proprietary Delay Measurement Default: Standard Usage Guide: To configure Tx mode (proprietary) of MEP.
PAGE 247
Command Guide Example: To configure Time Sync of MEP 1 Switch# configure terminal Switch (config)# mep 1 dm syncronized 4.2.133 mep down Command: mep [ mip ] down domain { port | evc | vlan } [ vid ] flow level interface mep Maintenance Entity Point mip This MEP instance is a half-MIP down The MEP instance number. This MEP is a Down-MEP domain The domain of the MEP evc This MEP is a EVC domain MEP.
PAGE 248
Command Guide 4.2.134 mep lb Command: mep lb [ dei ] [ multi | { uni { { mep-id } | { mac } } } ] count size interval mep Maintenance Entity Point lb The MEP instance number. Loop Back count Priority in case of tagged OAM. In the EVC domain this is the COS-ID. The number of LBM PDU to send in one loop test. The value 0 indicate infinite transmission (test behavior).
PAGE 249
Command Guide 4.2.135 mep lck Command: mep lck fr1m | fr1s mep Maintenance Entity Point lck fr1m fr1s The MEP instance number. Locked Signal Frame rate is 1 f/min. Frame rate is 1 f/s. Default: 1 frame/sec Usage Guide: To configure Locked Frame Rate of MEP. Example: To configure Locked Frame Rate (1 frame/sec) of MEP 2. Switch# configure terminal Switch (config)# mep 2 lck Switch (config)# mep 2 lck fr1s 4.2.
PAGE 250
Command Guide 4.2.137 mep lm Command: mep lm [ multi | uni ] [ single | dual ] [ fr10s | fr1s | fr6m | fr1m | fr6h ] [ flr ] mep Maintenance Entity Point lm The MEP instance number. Loss Measurement Priority in case of tagged OAM. In the EVC domain this is the COS-ID. fr10s Frame rate is 10 f/s. fr1m Frame rate is 1 f/min. fr1s Frame rate is 1 f/s. fr6h Frame rate is 6 f/hour. fr6m Frame rate is 6 f/min.
PAGE 251
Command Guide 4.2.138 mep lt Command: mep lt { { mep-id } | { mac } } ttl mep Maintenance Entity Point lt The MEP instance number. Link Trace mac Priority in case of tagged OAM. In the EVC domain this is the COS-ID. Link Trace target unicast MAC to be used in case of LT against MIP. mep-id Peer MEP-ID for Link Trace target unicast MAC. The MAC is taken from peer MEP MAC database.
PAGE 252
Command Guide itu The MEG-ID has ITU format (ICC - UMC). The meg-id max. is 13 characters. itu-cc The MEG-ID has ITU Country Code format (CC - ICC - UMC). The meg-id max. is 15 characters name Only relevant for IEEE. The MAID is with Maintenance Domain Name Maintenance Domain Name string. The max is 16 characters Default: Usage Guide: To configure MEG-ID of MEP.
PAGE 253
Command Guide 4.2.141 mep peer-mep-id Command: mep peer-mep-id [ mac ] mep Maintenance Entity Point The MEP instance number. peer-mep-id The peer MEP-ID The peer MEP-ID value The peer MAC. this will be overwritten by any learned MAC – through CCM reception. mac The peer MAC string Default: None Usage Guide: To configure Peer MEP-ID of MEP.
PAGE 254
Command Guide Example: To enable Performance Monitoring of MEP 1 Switch# configure terminal Switch (config)# mep 1 performance-monitoring 4.2.143 mep tst Command: mep tst [ dei ] mep-id [ sequence ] [ all-zero | all-one | one-zero ] rate size mep Maintenance Entity Point tst The MEP instance number. Test Signal dei Priority in case of tagged OAM. In the EVC domain this is the COS-ID.
PAGE 255
Command Guide Switch# configure terminal Switch (config)# mep 1 tst 3 dei mep-id 2 sequence one-zero rate 10 size 68 4.2.144 mep up Command: mep [mip] up domain { port | evc | vlan } [ vid ] flow level interface mep Maintenance Entity Point The MEP instance number. mip This MEP instance is a half-MIP up This MEP is a Up-MEP domain The domain of the MEP evc This MEP is a EVC domain MEP. port This MEP is a Port domain MEP.
PAGE 256
Command Guide 4.2.145 mep vid Command: mep vid mep Maintenance Entity Point The MEP instance number. vid The MEP VID The MEP VID value Default: 0 Usage Guide: To set VID of MEP. Example: To set VID (8) of MEP 1. Switch# configure terminal Switch (config)# mep 1 vid 8 4.2.146 mep voe Command: mep voe mep Maintenance Entity Point voe The MEP instance number.
PAGE 257
Command Guide 4.2.147 monitor destination Command: monitor destination interface 10GigabitEthernet | GigabitEthernet monitor Set monitor configuration destination The destination port. That is the port that trafficed should be mirrored to Default: Disabled Usage Guide: To configure Mirroring Port Example: To set Mirroring Port (GigabitEthernet 1/2) Switch# configure terminal Switch (config)# monitor destination interface GigabitEthernet 1/2 4.2.
PAGE 258
Command Guide 4.2.149 mvr Command: mvr mvr Multicast VLAN Registration configuration Default: Disabled Usage Guide: To enable MVR Example: To enable MVR Switch# configure terminal Switch (config)# mvr 4.2.
PAGE 259
Command Guide 4.2.
PAGE 260
Command Guide Example: To configure frame tagged (frame tagged) of MVR profile (123) Switch# configure terminal Switch (config)# mvr name 123 frame tagged 4.2.153 mvr name igmp-address Command: mvr name igmp-address mvr Multicast VLAN Registration configuration name MVR multicast name MVR multicast VLAN name igmp-address MVR address configuration used in IGMP A valid IPv4 unicast address Default: 0.0.0.
PAGE 261
Command Guide Default: 5 Usage Guide: To configure the Last Member Query Interval of MVR profile Example: To configure the Last Member Query Interval (50 seconds) of MVR profile (123) Switch# configure terminal Switch (config)# mvr name 123 last-member-query-interval 500 4.2.
PAGE 262
Command Guide MVR multicast VLAN list Default: None Usage Guide: To create a profile of MVR VLAN Example: To create a profile of MVR VLAN (5) Switch# configure terminal Switch (config)# mvr vlan 5 4.2.
PAGE 263
Command Guide mvr Multicast VLAN Registration configuration vlan MVR multicast vlan MVR multicast VLAN list frame MVR control frame in TX priority Interface CoS priority CoS priority ranges from 0 to 7 Default: 0 Usage Guide: To configure the frame priority of MVR VLAN Example: To configure the frame priority (5) of MVR VLAN (123) Switch# configure terminal Switch (config)# mvr vlan 123 frame priority 5 4.2.
PAGE 264
Command Guide 4.2.160 mvr vlan igmp-address Command: mvr vlan igmp-address mvr Multicast VLAN Registration configuration vlan MVR multicast vlan igmp-address MVR multicast VLAN list MVR address configuration used in IGMP A valid IPv4 unicast address Default: 0.0.0.0 Usage Guide: To configure the MVR address of MVR VLAN Example: To configure the MVR address (192.168.0.
PAGE 265
Command Guide Example: To configure the Last Member Query Interval (50 seconds) of MVR VLAN (123) Switch# configure terminal Switch (config)# mvr vlan 123 last-member-query-interval 500 4.2.
PAGE 266
Command Guide Default: None Usage Guide: To configure profile name of MVR VLAN Example: To configure profile name (6) of MVR VLAN (5) Switch# configure terminal Switch (config)# mvr vlan 5 name 6 4.2.164 network-clock clk-source aneg-mode Command: network-clock clk-source aneg-mode { master | slave | forced } network-clock network-clock clk-source clk-source - commands related to a specific clock source.
PAGE 267
Command Guide 4.2.165 no Command: no no Negate a command or set its defaults Default: N/A Usage Guide: To default the function Example: To disable the function (loop-protect) Switch# configure terminal Switch (config)# no loop-protect 4.2.166 ntp Command: ntp ntp Configure NTP Default: Disabled Usage Guide: To enable the NTP service Example: To enable the NTP service Switch# configure terminal Switch (config)# ntp 4.2.
PAGE 268
Command Guide ntp Configure NTP server Configure NTP server <1-5> index number domain name ipv4 address ipv6 address Default: None Usage Guide: To configure the IP addresses of NTP Server Example: To configure the IP address (9.9.9.9) of NTP Server for index 1 Switch# configure terminal Switch (config)# ntp server 1 ip-address 9.9.9.9 4.2.
PAGE 269
Command Guide 4.2.169 poe management mode Command: poe management mode allocation-consumption | { class-consumption | allocation-reserved-power class-reserved-power | | | lldp-consumption lldp-reserved-power } poe Power Over Ethernet management mode Use management mode to configure PoE power management method. mode allocation-consumption Max. port power determined by allocated, and power is managed according to power consumption.
PAGE 270
Command Guide Default: Enabled Usage Guide: To enable Sequential Power up Option. Example: To enable Sequential Power up Option. Switch# configure terminal Switch (config)# poe sequential enable 4.2.171 poe sequential interval Command: poe sequential interval <1-30> poe Power Over Ethernet sequential interval PoE sequential is to delay power feeding when the switch is completely booted.
PAGE 271
Command Guide priority Use priority command to configure sequential feeding power to PoE interfaces based on port PoE priority. Default: Port Usage Guide: To configure Sequential Power up Port Option. Example: To configure Sequential Power up Port Option (Priority). Switch# configure terminal Switch (config)# poe sequential rule priority 4.2.173 poe supply Command: poe supply <1-XXX> poe Power Over Ethernet supply Use poe supply to specify the maximum power the power supply can deliver.
PAGE 272
Command Guide Default: Enabled Usage Guide: To enable PoE Temperature Protection. Example: To enable PoE Temperature Protection. Switch# configure terminal Switch (config)# poe temperature-protection enable 4.2.175 poe temperature-threshold Command: poe temperature-threshold <0-100> poe Power Over Ethernet temperature-threshold <0-100> Set a lower high temperature threshold for the secondary temperature alarm in degrees C. Specifies the new threshold temperature.
PAGE 273
Command Guide Default: 85 Usage Guide: To configure PoE Usage Threshold. Example: To configure PoE Usage Threshold (90 %). Switch# configure terminal Switch (config)# poe usage-threshold 90 4.2.177 poe-time-range Command: poe-time-range {profile1 | profile2 | profile3 | profile4} poe-time-range Used to create PoE time-range for the switch and enter Power Time-range Create Configuration Mode.
PAGE 274
Command Guide Default: N/A Usage Guide: To run exec commands Example: To run “show aaa”. Switch# configure terminal Switch (config)# poe-time-range profile1 Switch (config-poe-time-range)#do show aaa console : local telnet : local ssh http : local : local 4.2.177.
PAGE 275
Command Guide 4.2.177.3 exit Command: exit exit Exit from current mode Default: None Usage Guide: To exit current mode Example: To exit current mode. Switch# configure terminal Switch (config)# poe-time-range profile1 Switch (config-poe-time-range)#exit Switch (config)# 4.2.177.4 no Command: no no Negate a command or set its defaults Default: N/A Usage Guide: To default the function. Example: To enable the function (description 999).
PAGE 276
Command Guide periodic { Mon | Tue | Wed | Thu | Fri | Sat | Sun } to [ reboot ] periodic Fri To create a periodic mode time-range for the PoE time-range of the switch. Periodic Mode, with Friday. Mon Periodic Mode, with Monday. Sat Periodic Mode, with Saturday. Sun Periodic Mode, with Sunday. Thu Periodic Mode, with Thursday. Tue Periodic Mode, with Tuesday. Wed Periodic Mode, with Wednesday.
PAGE 277
Command Guide Fri Periodic Mode, with Friday. Mon Periodic Mode, with Monday. Sat Periodic Mode, with Saturday. Sun Periodic Mode, with Sunday. Thu Periodic Mode, with Thursday. Tue Periodic Mode, with Tuesday. Wed Periodic Mode, with Wednesday. < reboot_h: 0-23> <0-23> reboot hour < reboot_m:0-59> <0-59> reboot minute Default: N/A Usage Guide: To configure the Power Over Ethernet Reboot Schedule for specific profile.
PAGE 278
Command Guide Example: To enable the Port Security Switch# configure terminal Switch (config)# port-security 4.2.179 port-security aging Command: port-security aging port-security aging Enable/disable port security globally Enable/disable port security aging Default: Disabled Usage Guide: To enable the Port Aging Example: To enable the Port Aging Switch# configure terminal Switch (config)# port-security port-security aging 4.2.
PAGE 279
Command Guide Example: To configure the Aging Period (159) of Port Security Switch# configure terminal Switch (config)# port-security aging time 159 4.2.
PAGE 280
Command Guide 4.2.
PAGE 281
Command Guide Example: To configure the DSCP Classification (QoS Class 3: DSCP CS1) Switch# configure terminal Switch (config)# qos map cos-dscp 3 dscp cs1 4.2.
PAGE 282
Command Guide Usage Guide: To enabled the DSCP Ingress Classification Example: To configure the DSCP Ingress Classification (DSCP 36) Switch# configure terminal Switch (config)# qos map dscp-classify af42 4.2.
PAGE 283
Command Guide va Voice Admit PHB(DSCP 44) cos Specify class of service dpl Specific class of service Specify drop precedence level Specific drop precedence level Default: 0 Usage Guide: To configure the DSCP-Based QoS Ingress Classification Example: To configure the DSCP-Based QoS Ingress Classification (DSCP: 44, QoS Class: 6, DPL: 2) Switch# configure terminal Switch (config)# qos map dscp-cos va cos 6 dpl 2 4.2.
PAGE 284
Command Guide be Default PHB(DSCP 0) for best effort traffic cs1 Class Selector PHB CS1 precedence 1(DSCP 8) cs2 Class Selector PHB CS2 precedence 2(DSCP 16) cs3 Class Selector PHB CS3 precedence 3(DSCP 24) cs4 Class Selector PHB CS4 precedence 4(DSCP 32) cs5 Class Selector PHB CS5 precedence 5(DSCP 40) cs6 Class Selector PHB CS6 precedence 6(DSCP 48) cs7 Class Selector PHB CS7 precedence 7(DSCP 56) ef Expedited Forwarding PHB(DSCP 46) va Voice Admit PHB(DSCP 44) Default: None Usage Guid
PAGE 285
Command Guide af32 Assured Forwarding PHB AF32(DSCP 28) af33 Assured Forwarding PHB AF33(DSCP 30) af41 Assured Forwarding PHB AF41(DSCP 34) af42 Assured Forwarding PHB AF42(DSCP 36) af43 Assured Forwarding PHB AF43(DSCP 38) be Default PHB(DSCP 0) for best effort traffic cs1 Class Selector PHB CS1 precedence 1(DSCP 8) cs2 Class Selector PHB CS2 precedence 2(DSCP 16) cs3 Class Selector PHB CS3 precedence 3(DSCP 24) cs4 Class Selector PHB CS4 precedence 4(DSCP 32) cs5 Class Selector PHB CS
PAGE 286
Command Guide af43 | cs1 | cs2 | cs3 | cs4 | cs5 | cs6 | cs7 | ef | va } | any } ] [ fragment { yes | no | any } ] [ sport { | any } ] [ dport { | any } ] } | { ipv6 [ proto { | tcp | udp | any } ] [ sip { | any } ] [ dip { | any } ] [ dscp { | { be | af11 | af12 | af13 | af21 | af22 | af23 | af31 | af32 | af33 | af41 | af42 | af43 | cs1 | cs2 | cs3 | cs4 | cs5 | cs6 | cs7 | ef | va } | any } ] [ sport { | any } ] [ dport { | any } ] } } ] [ action { [ cos
PAGE 287
Command Guide Switch# configure terminal Switch (config)# qos qce 1 interface GigabitEthernet 1/1-2 tag type tagged vid 5 pcp 3 dei 1 dmac unicast frame-type ipv4 proto udp dscp 19 frag no sport 55 action cos 0 dpl 1 dscp 4 4.2.
PAGE 288
Command Guide Default: None Usage Guide: To update the QCE Example: To update the QCE 1 (DMAC: Unicast, Action: Cos 0). Switch# configure terminal Switch (config)# qos qce update 1 dmac unicast action cos 0 4.2.189 qos qce refresh Command: qos qce refresh qos Quality of Service qce QoS Control Entry refresh Refresh QCE tables in hardware Default: None Usage Guide: To refresh the QCE Example: To refresh the QCE. Switch# configure terminal Switch (config)# qos qce refresh 4.2.
PAGE 289
Command Guide min-th Specific queue or range Specify minimum threshold mdp-1 Specific minimum threshold in percent Specify drop probability for drop precedence level 1 mdp-2 Specific drop probability in percent Specify drop probability for drop precedence level 2 mdp-3 Specific drop probability in percent Specify drop probability for drop precedence level 3 Specific drop probability in percent Default: Usage Guide: To
PAGE 290
Command Guide Default: None Usage Guide: To configure the NAS-Identifier Example: To configure the NAS-Identifier (planet) Switch# configure terminal Switch (config)# radius-server attribute 32 planet 4.2.192 radius-server attribute 4 Command: radius-server attribute 4 radius-server 4 Configure RADIUS NAS-IP-Address Default: None Usage Guide: To configure the NAS-IP-Address Example: To configure the NAS-IP-Address (7.7.7.
PAGE 291
Command Guide Usage Guide: To configure the NAS-IPv6-Address Example: To configure the NAS-IPv6-Address (2001::7788) Switch# configure terminal Switch (config)# radius-server attribute 95 2001::7788 4.2.
PAGE 292
Command Guide key UDP port number Server specific key (overrides default) retransmit The shared key Specify the number of retries to active server (overrides default) timeout Number of retries for a transaction Time to wait for this RADIUS server to reply (overrides default) Wait time in seconds Default: None Usage Guide: To configure the Host of Radius-Server Example: To configure the Host (below table) of Radius-Server
PAGE 293
Command Guide 4.2.197 radius-server retransmit Command: radius-server retransmit radius-server retransmit Configure RADIUS Specify the number of retries to active server Number of retries for a transaction Default: 3 Usage Guide: To configure the retransmitted time of Radius-Server Example: To configure the retransmitted time (5) of Radius-Server Switch# configure terminal Switch (config)# radius-server retransmit 5 4.2.
PAGE 294
Command Guide 4.2.
PAGE 295
Command Guide Default: None Usage Guide: To configure the Alarm of RMON Example: To configure the Alarm (below table) of RMON Switch# configure terminal Switch (config)# rmon alarm 1 .1.3.6.1.2.1.2.2.1.10.15 50 absolute rising-threshold 1000 1 falling-threshold 520 1 falling 4.2.
PAGE 296
Command Guide 4.2.201 sflow agent-ip Command: sflow agent-ip { ipv4 | ipv6 } sflow Statistics flow agent-ip The agent IP address used as agent-address in UDP datagrams. Defaults to IPv4 loopback address. Default: None Usage Guide: To configure the agent IP address of sFlow Example: To configure the agent IP address (10.10.10.10) of sFlow Switch# configure terminal Switch (config)# sflow agent-ip ipv4 10.10.10.10 4.2.
PAGE 297
Command Guide 4.2.203 sflow collector-port Command: sflow collector-port sflow Statistics flow collector-port Collector UDP port Port number Default: None Usage Guide: To configure the Collector port number of sFlow Example: To configure the Collector port number (555) of sFlow Switch# configure terminal Switch (config)# sflow collector-port 555 4.2.
PAGE 298
Command Guide 4.2.205 sflow timeout Command: sflow timeout sflow Statistics flow timeout Receiver timeout measured in seconds. The switch decrements the timeout once per second, and as long as it is non-zero, the receiver receives samples. Once the timeout reaches 0, the receiver and all its configuration is reset to defaults.
PAGE 299
Command Guide 4.2.207 snmp-server Command: snmp-server snmp-server Set SNMP server's configurations Default: Enabled Usage Guide: To enable the SNMP Service Example: To enable the SNMP Service Switch# configure terminal Switch (config)# snmp-server 4.2.
PAGE 300
Command Guide Default: None Usage Guide: To configure the Access of SNMP Example: To configure the Access (below table) of SNMP Switch# configure terminal Switch (config)# snmp-server access default_rw_group model v2c level priv read default_view write default_view 4.2.
PAGE 301
Command Guide Switch# configure terminal Switch (config)# snmp-server community v3 public 192.168.0.15 255.255.255.0 4.2.
PAGE 302
Command Guide Example: To configure the Engine ID (1234567890) of SNMP Switch# configure terminal Switch (config)# snmp-server engine-id local 1234567890 4.2.
PAGE 303
Command Guide Example: To run “show aaa”. Switch# configure terminal Switch (config)# snmp-server host planet Switch (config-snmps-host)#do show aaa console : local telnet : local ssh http : local : local 4.2.212.2 end Command: end end Go back to EXEC mode Default: Auto Usage Guide: To back to EXEC mode Example: To back to EXEC mode Switch# configure terminal Switch (config)# snmp-server host planet Switch (config-snmps-host)#end Switch# 4.2.212.
PAGE 304
Command Guide Default: None Usage Guide: To exit current mode Example: To exit current mode. Switch# configure terminal Switch (config)# snmp-server host planet Switch (config-snmps-host)#exit Switch (config)# 4.2.212.
PAGE 305
Command Guide 4.2.212.5 no Command: no no Negate a command or set its defaults Default: N/A Usage Guide: To default the function Example: To disable the function (host planet.com 66 informs) Switch# configure terminal Switch (config)# snmp-server host planet Switch (config-snmps-host)# no ip address dhcp 4.2.212.
PAGE 306
Command Guide Switch# configure terminal Switch (config)# snmp-server host planet Switch (config-snmps-host)# informs retries 2 timeout 55 4.2.212.7 shutdown Command: shutdown shutdown Disable the trap configuration Default: Disabled Usage Guide: To disable Trap mode of SNMP Example: To disable Trap mode of SNMP Switch# configure terminal Switch (config)# snmp-server host planet Switch (config-snmps-host)# shutdown 4.2.212.
PAGE 307
Command Guide Default: Disabled Usage Guide: To configure Trap event of SNMP Example: To configure Trap event (STP, RMON) of SNMP Switch# configure terminal Switch (config)# snmp-server host planet Switch (config-snmps-host)# traps switch rmon stp 4.2.212.
PAGE 308
Command Guide 4.2.213 spanning-tree aggregation Command: spanning-tree aggregation spanning-tree aggregation Spanning Tree protocol Aggregation mode Default: None Usage Guide: To enter aggregation mode of STP Example: To enter aggregation mode of STP Switch# configure terminal Switch (config)# spanning-tree aggregation Switch (config-stp-aggr)# 4.2.213.1 do Command: do < exec commands > do To run exec commands. Default: N/A Usage Guide: To run exec commands. Example: To run “show aaa”.
PAGE 309
Command Guide 4.2.213.2 end Command: end end Go back to EXEC mode Default: Auto Usage Guide: To back to EXEC mode Example: To back to EXEC mode Switch# configure terminal Switch (config)# spanning-tree aggregation Switch (config-stp-aggr)#end Switch# 4.2.213.3 exit Command: exit exit Exit from current mode Default: None Usage Guide: To exit current mode Example: To exit current mode.
PAGE 310
Command Guide 4.2.213.4 no Command: no no Negate a command or set its defaults Default: N/A Usage Guide: To default the function Example: To disable the function (spanning-tree auto-edge) Switch# configure terminal Switch (config)# snmp-server host planet Switch (config-snmps-host)# no spanning-tree auto-edge 4.2.213.
PAGE 311
Command Guide 4.2.213.6 spanning-tree bpdu-guard Command: spanning-tree bpdu-guard spanning-tree bpdu-guard Spanning Tree protocol Enable/disable BPDU guard Default: Disabled Usage Guide: To enable the BPDU Guard of CIST Aggregated Port Example: To enable the BPDU Guard of CIST Aggregated Port Switch# configure terminal Switch (config)# snmp-server host planet Switch (config-snmps-host)# spanning-tree bpdu-guard 4.2.213.
PAGE 312
Command Guide 4.2.213.
PAGE 313
Command Guide Switch# configure terminal Switch (config)# snmp-server host planet Switch (config-snmps-host)# spanning-tree mst 2 cost 321 4.2.213.10 spanning-tree mst port-priority Command: spanning-tree mst port-priority spanning-tree Spanning Tree protocol mst STP bridge instance port-priority instance 0-7 (CIST=0, MST1=1...
PAGE 314
Command Guide Example: To enable the Restricted Role of CIST Switch# configure terminal Switch (config)# snmp-server host planet Switch (config-snmps-host)# spanning-tree restricted-role 4.2.213.
PAGE 315
Command Guide Usage Guide: To configure the VLAN Translation Example: To enable the VLAN Translation (below table) Switch# configure terminal Switch (config)# switchport vlan mapping 1 3 5 4.2.
PAGE 316
Command Guide port TCP port for TACACS+ server timeout TCP port number Time to wait for this TACACS+ server to reply (overrides default) Wait time in seconds The shared key Default: None Usage Guide: To configure the Host of TACACS+ Server Example: To enable the Host (below table) of TACACS+ Server Switch# configure terminal Switch (config)# tacacs-server host planet.com port 55 timeout 6 key 7788 4.2.
PAGE 317
Command Guide 4.2.218 transport email from Command: transport email from subject transport Enable or disable transport email function. email Enable or disable transport email function. from sender's email address <mail_addr> subject mail address subject/title of the email <title> email title Default: N/A Usage Guide: To configure SMTP sender's email address and title of the email Example: To configure SMTP sender's email address (sys@planet.com.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/igs-5225-16t4s/igs-5225-series-user-manual-catalan-english-french-dutch/page-318.html>PAGE 318</a></h6><p>Command Guide Example: To configure SMTP Server address (mail.planet.com.tw) and port number (123) Switch# configure terminal Switch (config)# transport email smtp-server mail.planet.com.tw port 123 4.2.220 transport email to Command: transport email to <1 | 2> <mail_addr> transport email to Enable or disable transport email function. Enable or disable transport email function.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/igs-5225-16t4s/igs-5225-series-user-manual-catalan-english-french-dutch/page-319.html>PAGE 319</a></h6><p>Command Guide Example: To enable the UPnP service Switch# configure terminal Switch (config)# upnp 4.2.222 upnp advertising-duration Command: upnp advertising-duration <100-86400> upnp Set UPnP's configurations advertising-duration <100-86400> Set advertising duration advertising duration Default: 100 Usage Guide: To configure the Advertising Duration of UPnP Example: To configure the Advertising Duration (123) of UPnP Switch# configure terminal Switch (config)# upnp advertising-duration 123 4.2.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/igs-5225-16t4s/igs-5225-series-user-manual-catalan-english-french-dutch/page-320.html>PAGE 320</a></h6><p>Command Guide Example: To configure the TTL (8) of UPnP Switch# configure terminal Switch (config)# upnp ttl 8 4.2.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/igs-5225-16t4s/igs-5225-series-user-manual-catalan-english-french-dutch/page-321.html>PAGE 321</a></h6><p>Command Guide 4.2.225 vlan Command: vlan <vlist> vlan VLAN commands <vlan_list> VLAN IDs 1~4095 Default: None Usage Guide: To create the VLAN Profiles Example: To create the VLAN Profiles (VLAN 5) Switch# configure terminal Switch (config)# vlan 5 Switch (config-vlan)# 4.2.225.1 do Command: do < exec commands > do To run exec commands. Default: N/A Usage Guide: To run exec commands. Example: To run “show aaa”.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/igs-5225-16t4s/igs-5225-series-user-manual-catalan-english-french-dutch/page-322.html>PAGE 322</a></h6><p>Command Guide 4.2.225.2 end Command: end end Go back to EXEC mode Default: Auto Usage Guide: To back to EXEC mode Example: To back to EXEC mode Switch# configure terminal Switch (config)# vlan 5 Switch (config-vlan)#end Switch# 4.2.225.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/igs-5225-16t4s/igs-5225-series-user-manual-catalan-english-french-dutch/page-323.html>PAGE 323</a></h6><p>Command Guide 4.2.225.4 name Command: name <vlan_name> name ASCII name of the VLAN <vword32> The ASCII name for the VLAN Default: None Usage Guide: To configure description of VLAN Example: To configure description (FAE) of VLAN Switch# configure terminal Switch (config)# vlan 5 Switch (config-vlan)# name FAE 4.2.225.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/igs-5225-16t4s/igs-5225-series-user-manual-catalan-english-french-dutch/page-324.html>PAGE 324</a></h6><p>Command Guide 4.2.226 vlan ethertype s-custom-port Command: vlan ethertype s-custom-port <etype> vlan VLAN commands ethertype Ether type for Custom S-ports s-custom-port <etype> Custom S-ports configuration Ethertype (Range: 0x0600-0xffff) Default: 0x88A8 Usage Guide: To create the Ethernet type of Custom S-ports Example: To create the Ethernet type (0x88A9) of Custom S-ports Switch# configure terminal Switch (config)# vlan ethertype s-custom-port 0x88a9 4.2.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/igs-5225-16t4s/igs-5225-series-user-manual-catalan-english-french-dutch/page-325.html>PAGE 325</a></h6><p>Command Guide snap-8021h group SNAP OUI is 8021h Protocol-based VLAN group commands <grp_id> Group Name (Range: 1 - 16 characters) Default: None Usage Guide: To configure the Protocol-based VLAN Example: To configure the Protocol-based VLAN (below table) Switch# configure terminal Switch (config)# vlan protocol llc 0x55 0x66 group 3 4.2.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/igs-5225-16t4s/igs-5225-series-user-manual-catalan-english-french-dutch/page-326.html>PAGE 326</a></h6><p>Command Guide 4.2.229 voice vlan aging-time Command: voice vlan aging-time <aging_time> voice vlan Voice appliance attributes Vlan for voice traffic aging-time Set secure learning aging time <agingtime : 10-10000000> Aging time, 10-10000000 seconds Default: 86400 Usage Guide: To configure the Aging Time of Voice VLAN Example: To configure the Aging Time of Voice VLAN Switch# configure terminal Switch (config)# voice vlan aging-time 8888 4.2.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/igs-5225-16t4s/igs-5225-series-user-manual-catalan-english-french-dutch/page-327.html>PAGE 327</a></h6><p>Command Guide 4.2.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/igs-5225-16t4s/igs-5225-series-user-manual-catalan-english-french-dutch/page-328.html>PAGE 328</a></h6><p>Command Guide Example: To configure the VID (66 ) of Voice VLAN Switch# configure terminal Switch (config)# voice vlan vid 66 4.2.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/igs-5225-16t4s/igs-5225-series-user-manual-catalan-english-french-dutch/page-329.html>PAGE 329</a></h6><p>Command Guide 4.3 copy 4.3.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/igs-5225-16t4s/igs-5225-series-user-manual-catalan-english-french-dutch/page-330.html>PAGE 330</a></h6><p>Command Guide Example: To configure Description (1233) of Debug Prompt Switch # debug prompt 1233 1233# 4.5 delete 4.5.1 delete Command: delete <path> delete Delete one file in flash: file system <path : word> Name of file to delete Default: None Usage Guide: To delete Configuration File of Flash Example: To delete Configuration File (222) of Flash Switch # copy running-config flash:222 Building configuration...</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/igs-5225-16t4s/igs-5225-series-user-manual-catalan-english-french-dutch/page-331.html>PAGE 331</a></h6><p>Command Guide rw 1970-01-01 07:26:26 1833 startup-config 2 files, 2481 bytes total. 4.6 dir 4.6.1 dir Command: dir dir Directory of all files in flash: file system Default: None Usage Guide: To list directory of file system Example: To list directory of file system Switch # dir Directory of flash: r- 1970-01-01 00:00:00 648 default-config rw 1970-01-01 07:26:26 1833 startup-config 2 files, 2481 bytes total. 4.7 disable 4.7.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/igs-5225-16t4s/igs-5225-series-user-manual-catalan-english-french-dutch/page-332.html>PAGE 332</a></h6><p>Command Guide Usage Guide: To exit enable mode Example: To exit enable mode Switch # disable Switch > 4.8 do 4.8.1 do Command: do < exec commands > do To run exec commands. Default: N/A Usage Guide: To run exec commands. Example: To run “show aaa”.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/igs-5225-16t4s/igs-5225-series-user-manual-catalan-english-french-dutch/page-333.html>PAGE 333</a></h6><p>Command Guide 4.9 dot1x 4.9.1 dot1x initialize Command: dot1x initialize [ interface ( <port_type> [ <plist> ] ) ] dot1x IEEE Standard for port-based Network Access Control initialize Force re-authentication immediately Default: N/A Usage Guide: To re-authenticate specific interface immediately. Example: To re-authenticate specific interface (GigabitEthernet 1/1) immediately. Switch# dot1x initialize interface GigabitEthernet 1/1 4.10 enable 4.10.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/igs-5225-16t4s/igs-5225-series-user-manual-catalan-english-french-dutch/page-334.html>PAGE 334</a></h6><p>Command Guide 4.11 erps 4.11.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/igs-5225-16t4s/igs-5225-series-user-manual-catalan-english-french-dutch/page-335.html>PAGE 335</a></h6><p>Command Guide 4.12 exit 4.12.1 exit Command: exit exit Exit from EXEC mode Default: None Usage Guide: To exit EXEC mode Example: To exit EXEC mode Switch # disable Switch > exit Press ENTER to get started 4.13 firmware 4.13.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/igs-5225-16t4s/igs-5225-series-user-manual-catalan-english-french-dutch/page-336.html>PAGE 336</a></h6><p>Command Guide Example: To swap Active and Alternate firmware image Switch # firmware swap 4.13.2 firmware upgrade Command: firmware upgrade <tftpserver_path_file> firmware Firmware upgrade/swap upgrade Firmware upgrade <tftpserver_path_file : word> TFTP Server IP address, path and file name for the server containing the new image. Default: None Usage Guide: To upgrade firmware via TFTP Server Example: To upgrade firmware via TFTP Server (File: tftp://192.168.0.11/switch.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/igs-5225-16t4s/igs-5225-series-user-manual-catalan-english-french-dutch/page-337.html>PAGE 337</a></h6><p>Command Guide Default: None Usage Guide: To do DHCP renew for specific VLAN Example: To do DHCP renew for specific VLAN (6) Switch # ip dhcp retry interface vlan 6 4.15 logout 4.15.1 logout Command: logout logout Exit from EXEC mode Default: None Usage Guide: To exit EXEC mode Example: To exit EXEC mode Switch # logout Press ENTER to get started 4.16 more 4.16.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/igs-5225-16t4s/igs-5225-series-user-manual-catalan-english-french-dutch/page-338.html>PAGE 338</a></h6><p>Command Guide Default: None Usage Guide: To view the file Example: To view the file (222) Switch # copy running-config flash:222 Building configuration... % Saving 2038 bytes to flash:222 Switch # more flash:222 hostname Switch username admin privilege 15 password none ! vlan 1 ! vlan 5 ! ! ! 4.17 no 4.17.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/igs-5225-16t4s/igs-5225-series-user-manual-catalan-english-french-dutch/page-339.html>PAGE 339</a></h6><p>Command Guide Example: To disable the function (erps 1 command force port0) Switch# no erps 1 command force port0 4.18 ping 4.18.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/igs-5225-16t4s/igs-5225-series-user-manual-catalan-english-french-dutch/page-340.html>PAGE 340</a></h6><p>Command Guide 4.18.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/igs-5225-16t4s/igs-5225-series-user-manual-catalan-english-french-dutch/page-341.html>PAGE 341</a></h6><p>Command Guide 4.19 reload 4.19.1 reload cold Command: reload cold reload Reload system cold Reload cold. Default: N/A Usage Guide: To restart the device. Example: To restart the device. Switch# reload cold 4.19.2 reload defaults Command: reload defaults [ keep-ip ] reload Reload system defaults keep-ip Reload defaults without rebooting. Attempt to keep VLAN1 IP setup. Default: N/A Usage Guide: To store the device factory default settings. Example: To store the device factory default settings.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/igs-5225-16t4s/igs-5225-series-user-manual-catalan-english-french-dutch/page-342.html>PAGE 342</a></h6><p>Command Guide 4.20 send 4.20.1 send Command: send { * | console 0 | vty <vty_list> } <message> reload Reload system * All tty lines console vty Primary terminal line Virtual terminal Default: N/A Usage Guide: To send message for command line user. Example: To send message ( hi, I will upgrade the firmware, OK? ) for command line user (All). Switch # send * 1 Enter TEXT message. End with the character '1'.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/igs-5225-16t4s/igs-5225-series-user-manual-catalan-english-french-dutch/page-343.html>PAGE 343</a></h6><p>Command Guide 4.21 show 4.21.1 show aaa Command: show aaa show Show running system information aaa Login methods Default: N/A Usage Guide: To display the AAA services. Example: To display the AAA services Switch # show aaa console : local telnet ssh : local : local http : local 4.21.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/igs-5225-16t4s/igs-5225-series-user-manual-catalan-english-french-dutch/page-344.html>PAGE 344</a></h6><p>Command Guide Switch # show access management statistics Access Management Statistics: ----------------------------HTTP Receive: 0 Allow: 0 Discard: 0 HTTPS Receive: 0 Allow: 0 Discard: 0 SNMP Receive: 0 Allow: 0 Discard: 0 TELNET Receive: 0 Allow: 0 Discard: 0 SSH Receive: 0 Allow: 0 Discard: 0 4.21.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/igs-5225-16t4s/igs-5225-series-user-manual-catalan-english-french-dutch/page-345.html>PAGE 345</a></h6><p>Command Guide Switch access-list rate limiter ID 6 is 1 pps Switch access-list rate limiter ID 7 is 1 pps Switch access-list rate limiter ID 8 is 1 pps Switch access-list rate limiter ID 9 is 1 pps Switch access-list rate limiter ID 10 is 1 pps Switch access-list rate limiter ID 11 is 1 pps Switch access-list rate limiter ID 12 is 1 pps Switch access-list rate limiter ID 13 is 1 pps Switch access-list rate limiter ID 14 is 1 pps Switch access-list rate limiter ID 15 is 1 pps Switch access-list rate limiter</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/igs-5225-16t4s/igs-5225-series-user-manual-catalan-english-french-dutch/page-346.html>PAGE 346</a></h6><p>Command Guide Usage Guide: To display the ACL Statistics, Rate Limiter List, ACE Statistics. Example: To display the ACL Statistics, Rate Limiter List, ACE Statistics for interface GigabitEthernet 1/1.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/igs-5225-16t4s/igs-5225-series-user-manual-catalan-english-french-dutch/page-347.html>PAGE 347</a></h6><p>Command Guide 4.21.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/igs-5225-16t4s/igs-5225-series-user-manual-catalan-english-french-dutch/page-348.html>PAGE 348</a></h6><p>Command Guide User ID ---- -- Frame ----- Action Rate L. CPU Counter Conflict ------ -------- ------ ------- -------- DHCP 1 UDP Deny Disabled Yes 0 No DHCP 2 UDP Deny Disabled Yes 0 No PTP 1 EType Deny Disabled Yes 0 No PTP 2 EType Deny Disabled Yes 0 No Switch 1 access-list ace number: 4 4.21.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/igs-5225-16t4s/igs-5225-series-user-manual-catalan-english-french-dutch/page-349.html>PAGE 349</a></h6><p>Command Guide Default: N/A Usage Guide: To display the Aggregation mode status. Example: To display the Aggregation mode status. Switch # show aggregation mode Aggregation Mode: SMAC : Enabled DMAC : Disabled IP : Enabled Port : Enabled 4.21.8 show clock Command: show clock show Show running system information clock Configure time-of-day clock Default: N/A Usage Guide: To display the system time. Example: To display the system time.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/igs-5225-16t4s/igs-5225-series-user-manual-catalan-english-french-dutch/page-350.html>PAGE 350</a></h6><p>Command Guide 4.21.9 show clock detail Command: show clock detail show Show running system information clock Configure time-of-day clock detail Display detailed information Default: N/A Usage Guide: To display the detailed system time. Example: To display the detailed system time. Switch # show clock detail System Time : 1970-01-01T00:29:25+00:00 Timezone : Timezone Offset : 0 ( 0 minutes) Timezone Acronym : Daylight Saving Time Mode : Disabled.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/igs-5225-16t4s/igs-5225-series-user-manual-catalan-english-french-dutch/page-351.html>PAGE 351</a></h6><p>Command Guide 4.21.10 show dot1x statistics Command: show dot1x statistics show Show running system information dot1x IEEE Standard for port-based Network Access Control statistics all Shows statistics for either eapol or radius Show all dot1x statistics eapol Show EAPOL statistics radius Show Backend Server statistics interface Interface Default: N/A Usage Guide: To display the IEEE 802.1X statistics. Example: To display the All of IEEE 802.1X statistics for interface GigabitEthernet 1/1.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/igs-5225-16t4s/igs-5225-series-user-manual-catalan-english-french-dutch/page-352.html>PAGE 352</a></h6><p>Command Guide 4.21.11 show dot1x status Command: show dot1x status [ interface ( <port_type> [ <v_port_type_list> ] ) ] [ brief ] show Show running system information dot1x IEEE Standard for port-based Network Access Control status Shows dot1x status, such as admin state, port state and last source. interface Interface brief Show status in a brief format Default: N/A Usage Guide: To display the IEEE 802.1X status. Example: To display the All of IEEE 802.1X status for brief.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/igs-5225-16t4s/igs-5225-series-user-manual-catalan-english-french-dutch/page-353.html>PAGE 353</a></h6><p>Command Guide 4.21.12 show eps Command: show eps [ <inst> ] [ detail ] show Show running system information eps Ethernet Protection Switching <inst : range_list> detail The range of EPS instances Show detailed state including configuration information Default: N/A Usage Guide: To display the EPS instance information. Example: To display the EPS instance 1 detailed information.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/igs-5225-16t4s/igs-5225-series-user-manual-catalan-english-french-dutch/page-354.html>PAGE 354</a></h6><p>Command Guide 4.21.13 show erps Command: show erps [ <groups> ] [ detail | statistics ] show Show running system information erps Ethernet Ring Protection Switching <groups> Zero or more ERPS group numbers detail Show detailed information statistics Show statistics Default: N/A Usage Guide: To display the ERPS group information. Example: To display the ERPS group 1 detailed information.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/igs-5225-16t4s/igs-5225-series-user-manual-catalan-english-french-dutch/page-355.html>PAGE 355</a></h6><p>Command Guide Port 1 Block Status R-APS Transmission :BLOCKED :STOPPED R-APS Port 0 Reception :NONE R-APS Port 1 Reception :NONE FOP Alarm :OFF 4.21.14 show evc Command: show evc { [ <evc_id> | all ] } [ ece [ <ece_id> ] ] show Show running system information evc Ethernet Virtual Connections <evcid : 1-4096> EVC identifier all Process all EVCs ece EVC Control Entry <eceid : 1-4096> ECE idenfifier Default: N/A Usage Guide: To display the EVC status.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/igs-5225-16t4s/igs-5225-series-user-manual-catalan-english-french-dutch/page-356.html>PAGE 356</a></h6><p>Command Guide 4.21.15 show evc statistics Command: show green-ethernet [ interface ( <port_type> [ <port_list> ] ) ] show Show running system information green-ethernet Green ethernet (Power reduction) Default: N/A Usage Guide: To display the EVC statistics. Example: To display the EVC Red Frames statistics for all. Switch # show evc statistics all red EVC ID ------ Interface ----------------------- Rx Red Frames -------------------- 1 GigabitEthernet 1/1 0 1 GigabitEthernet 1/2 0 4.21.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/igs-5225-16t4s/igs-5225-series-user-manual-catalan-english-french-dutch/page-357.html>PAGE 357</a></h6><p>Command Guide 4.21.17 show green-ethernet energy-detect Command: show green-ethernet energy-detect [ interface ( <port_type> [ <port_list> ] ) ] show Show running system information green-ethernet energy-detect interface Green ethernet (Power reduction) Shows green ethernet energy-detect status for a specific port or ports. Shows green ethernet status for a specific port or ports. Default: N/A Usage Guide: To display the energy-detect of Green Ethernet.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/igs-5225-16t4s/igs-5225-series-user-manual-catalan-english-french-dutch/page-358.html>PAGE 358</a></h6><p>Command Guide 4.21.19 show history Command: show history show Show running system information history Display the session command history Default: N/A Usage Guide: To display the command history. Example: To display the command history.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/igs-5225-16t4s/igs-5225-series-user-manual-catalan-english-french-dutch/page-359.html>PAGE 359</a></h6><p>Command Guide Example: To display the SFP Transceiver information for interface GigabitEthernet 1/1. Switch # show interface GigabitEthernet 1/1 capabilities GigabitEthernet 1/1 Capabilities: SFP Type: None SFP Vendor name: SFP Vendor PN: SFP Vendor revision: 4.21.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/igs-5225-16t4s/igs-5225-series-user-manual-catalan-english-french-dutch/page-360.html>PAGE 360</a></h6><p>Command Guide GigabitEthernet 1/1 0 0 4.21.22 show interface <port_type> <port_type_list> status Command: show interface <port_type> <port_type_list> status show Show running system information interface Interface status and configuration status Display status Default: N/A Usage Guide: To display the port status. Example: To display the port status for interface GigabitEthernet 1/1.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/igs-5225-16t4s/igs-5225-series-user-manual-catalan-english-french-dutch/page-361.html>PAGE 361</a></h6><p>Command Guide Example: To display the VLAN mode for interface GigabitEthernet 1/1.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/igs-5225-16t4s/igs-5225-series-user-manual-catalan-english-french-dutch/page-362.html>PAGE 362</a></h6><p>Command Guide GigabitEthernet 1/1 Pair C Length OK 3 OK 3 Pair D Length ------ ------ ------ OK 3 OK ------3 4.21.25 show interface <port_type> <port_type_list> veriphy Command: show interface <port_type> <port_type_list> veriphy show Show running system information interface veriphy Interface status and configuration Run cable diagnostics and show result. Default: N/A Usage Guide: To display the result of Cable Diagnostics.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/igs-5225-16t4s/igs-5225-series-user-manual-catalan-english-french-dutch/page-363.html>PAGE 363</a></h6><p>Command Guide interface vlan Interface status and configuration VLAN status Default: N/A Usage Guide: To display the MAC address and IP address of specific VLAN. Example: To display the MAC address and IP address for all VLANs. Switch # show interface vlan VLAN1 LINK: 00-30-4F-00-99-00 Mtu:1500 <up broadcast running multicast> IPv4: 192.168.0.100/24 192.168.0.255 IPv6: fe80:2::201:c1ff:fe00:9900/64 <anycast tentative autoconf> 4.21.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/igs-5225-16t4s/igs-5225-series-user-manual-catalan-english-french-dutch/page-364.html>PAGE 364</a></h6><p>Command Guide 4.21.28 show ip arp inspection Command: show ip arp inspection show ip arp Show running system information Internet Protocol Address Resolution Protocol inspection ARP inspection Default: N/A Usage Guide: To display the ARP Inspection Configuration. Example: To display the ARP Inspection Configuration.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/igs-5225-16t4s/igs-5225-series-user-manual-catalan-english-french-dutch/page-365.html>PAGE 365</a></h6><p>Command Guide Example: To display the ARP Inspection Configuration. Switch # show ip arp inspection ARP Inspection Mode : disabled Port Port Mode Check VLAN Log Type ---- --------- ---------- -------- GigabitEthernet 1/1 disabled disabled NONE GigabitEthernet 1/2 disabled disabled NONE 4.21.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/igs-5225-16t4s/igs-5225-series-user-manual-catalan-english-french-dutch/page-366.html>PAGE 366</a></h6><p>Command Guide 4.21.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/igs-5225-16t4s/igs-5225-series-user-manual-catalan-english-french-dutch/page-367.html>PAGE 367</a></h6><p>Command Guide Rx Release: 0 Tx Release: 0 Rx Inform: 0 Tx Inform: 0 Rx Lease Query: 0 Tx Lease Query: 0 Rx Lease Unassigned: 0 Tx Lease Unassigned: 0 Rx Lease Unknown: 0 Tx Lease Unknown: 0 Rx Lease Active: 0 Tx Lease Active: 0 Rx Lease Active: 0 Tx Lease Active: 0 Rx Discarded checksum error: 0 4.21.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/igs-5225-16t4s/igs-5225-series-user-manual-catalan-english-french-dutch/page-368.html>PAGE 368</a></h6><p>Command Guide 4.21.33 show ip dhcp pool Command: show ip dhcp pool [ <pool_name> ] show ip Show running system information Internet Protocol dhcp Dynamic Host Configuration Protocol pool DHCP pools information Default: N/A Usage Guide: To display the DHCP pools information. Example: To display the DHCP pools information. Switch # show ip dhcp pool Pool Name: test ---------------------------------------------Type is network IP is 192.168.1.100 Subnet mask is 255.255.255.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/igs-5225-16t4s/igs-5225-series-user-manual-catalan-english-french-dutch/page-369.html>PAGE 369</a></h6><p>Command Guide 4.21.34 show ip dhcp relay Command: show ip dhcp relay [ statistics ] show Show running system information ip Internet Protocol dhcp Dynamic Host Configuration Protocol relay DHCP relay agent configuration statistics Traffic statistics Default: N/A Usage Guide: To display the DHCP relay information. Example: To display the DHCP relay information. Switch # show ip dhcp relay Switch DHCP relay mode is enabled Switch DHCP relay server address is 192.168.0.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/igs-5225-16t4s/igs-5225-series-user-manual-catalan-english-french-dutch/page-370.html>PAGE 370</a></h6><p>Command Guide Switch # show ip dhcp server DHCP server is globally disabled. All VLANs are disabled. 4.21.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/igs-5225-16t4s/igs-5225-series-user-manual-catalan-english-french-dutch/page-371.html>PAGE 371</a></h6><p>Command Guide 4.21.37 show ip dhcp server declined-ip (GG) Command: show ip dhcp server declined-ip show ip Show running system information Internet Protocol dhcp Dynamic Host Configuration Protocol server DHCP server information declined-ip Declined IP address Default: N/A Usage Guide: To display the DHCP Decline information. Example: To display the DHCP Decline information. Switch # show ip dhcp server declined-ip 4.21.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/igs-5225-16t4s/igs-5225-series-user-manual-catalan-english-french-dutch/page-372.html>PAGE 372</a></h6><p>Command Guide Database Counters ========================= POOL 2 Excluded IP 1 Declined IP 0 ========================= Binding Counters ========================= Automatic Manual Expired 0 0 0 ========================= Message Received Counters ========================= DISCOVER 0 REQUEST 0 DECLINE 0 RELEASE 0 INFORM 0 ========================= Message Sent Counters ========================= OFFER 0 ACK 0 NAK 0 ========================= 4.21.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/igs-5225-16t4s/igs-5225-series-user-manual-catalan-english-french-dutch/page-373.html>PAGE 373</a></h6><p>Command Guide Default: N/A Usage Guide: To display the DHCP Snooping configuration. Example: To display the DHCP Snooping configuration for GigabitEthernet 1/1. Switch # show ip dhcp snooping interface GigabitEthernet 1/1 GigabitEthernet 1/1 untrusted 4.21.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/igs-5225-16t4s/igs-5225-series-user-manual-catalan-english-french-dutch/page-374.html>PAGE 374</a></h6><p>Command Guide 4.21.41 show ip http server secure status Command: show ip http server secure status show ip Show running system information Internet Protocol http Hypertext Transfer Protocol server HTTP web server secure Secure status Status Default: N/A Usage Guide: To display the DHCP Snooping table. Example: To display the DHCP Snooping table. Switch # show ip http server secure status Switch secure HTTP web server is disabled Switch secure HTTP web redirection is disabled 4.21.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/igs-5225-16t4s/igs-5225-series-user-manual-catalan-english-french-dutch/page-375.html>PAGE 375</a></h6><p>Command Guide Usage Guide: To display the IGMP Snooping information. Example: To display the IGMP Snooping information (Detail). Switch # show ip igmp snooping detail IGMP Snooping is disabled to stop snooping IGMP control plane. Multicast streams destined to unregistered IGMP groups will be flooding. 4.21.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/igs-5225-16t4s/igs-5225-series-user-manual-catalan-english-french-dutch/page-376.html>PAGE 376</a></h6><p>Command Guide 4.21.44 show ip interface brief Command: show ip interface brief show Show running system information ip Internet Protocol interface brief IP interface status and configuration Brief IP interface status Default: N/A Usage Guide: To display the IP interface status. Example: To display the IP interface status. Switch # show ip interface brief Vlan Address Method Status ---- -------------------- -------- -----1 192.168.0.100/24 Manual UP 4.21.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/igs-5225-16t4s/igs-5225-series-user-manual-catalan-english-french-dutch/page-377.html>PAGE 377</a></h6><p>Command Guide 4.21.46 show ip route Command: show ip route show ip Show running system information Internet Protocol route Display the current ip routing table Default: N/A Usage Guide: To display the IP Routing table. Example: To display the IP Routing table. Switch # show ip route 11.11.11.0/24 via 192.168.0.14 <up gateway hw_rt> 127.0.0.1/32 via 127.0.0.1 <up host> 192.168.0.0/24 via VLAN1 <up hw_rt> 224.0.0.0/4 via 127.0.0.1 <up> 4.21.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/igs-5225-16t4s/igs-5225-series-user-manual-catalan-english-french-dutch/page-378.html>PAGE 378</a></h6><p>Command Guide Example: To display the Static IP Source Guard Table. Switch # show ip source binding interface GigabitEthernet 1/1 Type Port ---- ---- Static VLAN IP Address GigabitEthernet 1/1 ---1 ---------192.168.0.22 4.21.48 show ip ssh Command: show ip ssh show ip Show running system information Internet Protocol ssh Secure Shell Default: N/A Usage Guide: To display the SSH Management status. Example: To display the SSH Management status. Switch # show ip ssh Switch SSH is enabled 4.21.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/igs-5225-16t4s/igs-5225-series-user-manual-catalan-english-french-dutch/page-379.html>PAGE 379</a></h6><p>Command Guide Usage Guide: To display the IP statistics. Example: To display the IP statistics.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/igs-5225-16t4s/igs-5225-series-user-manual-catalan-english-french-dutch/page-380.html>PAGE 380</a></h6><p>Command Guide Rcvd: 2618 Messages, 0 Error Sent: 2618 Messages, 0 Error ICMP message statistics: IPv4 ICMP Message: Echo Reply Rcvd: 0 Packet Sent: 2618 Packets IPv4 ICMP Message: Echo Rcvd: 2618 Packets Sent: 0 Packet 4.21.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/igs-5225-16t4s/igs-5225-series-user-manual-catalan-english-french-dutch/page-381.html>PAGE 381</a></h6><p>Command Guide 4.21.51 show ipmc profile Command: show ipmc profile [ <profile_name> ] [ detail ] show Show running system information ipmc IPv4/IPv6 multicast configuration profile IPMC profile configuration <profilename : word16> detail Profile name Detail information of a profile Default: N/A Usage Guide: To display the IP Multicast Profile. Example: To display the IP Multicast Profile. Switch # show ipmc profile IPMC Profile is now enabled to start filtering.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/igs-5225-16t4s/igs-5225-series-user-manual-catalan-english-french-dutch/page-382.html>PAGE 382</a></h6><p>Command Guide Example: To display the IP Multicast Range. Switch # show ipmc range Range Name :1 Start Address: 224.24.24.24 End Address : 224.24.24.25 4.21.53 show ipv6 interface Command: show ipv6 interface [ vlan <vlan_list> { brief | statistics } ] show Show running system information ipv6 vlan IPv6 configuration commands VLAN of IPv6 interface brief Brief summary of IPv6 status and configuration statistics Traffic statistics Default: N/A Usage Guide: To display the IPv6 configuration.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/igs-5225-16t4s/igs-5225-series-user-manual-catalan-english-french-dutch/page-383.html>PAGE 383</a></h6><p>Command Guide 3 local destination, 0 forwarding 0 header error, 0 address error, 0 unknown protocol 0 no route, 0 truncated, 0 discarded Sent: 17 total in 1104 bytes 17 generated, 0 forwarded 0 discarded Frags: 0 reassemble (0 reassembled, 0 couldn't reassemble) 0 fragment (0 fragmented, 0 couldn't fragment) 0 fragment created Mcast: 3 received in 168 bytes 17 sent in 1104 bytes Bcast: 0 received, 0 sent 4.21.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/igs-5225-16t4s/igs-5225-series-user-manual-catalan-english-french-dutch/page-384.html>PAGE 384</a></h6><p>Command Guide Multicast streams destined to unregistered MLD groups will be flooding. 4.21.55 show ipv6 mld snooping mrouter Command: show ip igmp snooping mrouter [ detail ] show Show running system information ipv6 IPv6 configuration commands mld Multicast Listener Discovery snooping mrouter Snooping MLD Multicast router port status in MLD detail Detail running information/statistics of MLD snooping Default: N/A Usage Guide: To display the MLD Router Port information.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/igs-5225-16t4s/igs-5225-series-user-manual-catalan-english-french-dutch/page-385.html>PAGE 385</a></h6><p>Command Guide Default: N/A Usage Guide: To display the IPv6 neighbor information. Example: To display the IPv6 neighbor information. Switch # show ipv6 neighbor 2001::7766 via VLAN1: 00-30-4F-00-99-00 Permanent/REACHABLE fe80::201:c1ff:fe00:9900 via VLAN1: 00-30-4F-00-99-00 Permanent/REACHABLE 4.21.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/igs-5225-16t4s/igs-5225-series-user-manual-catalan-english-french-dutch/page-386.html>PAGE 386</a></h6><p>Command Guide 4.21.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/igs-5225-16t4s/igs-5225-series-user-manual-catalan-english-french-dutch/page-387.html>PAGE 387</a></h6><p>Command Guide IP interface statistics: IPv6 Statistics on Interface VLAN: 1 Rcvd: 12 total in 1032 bytes 3 local destination, 0 forwarding 0 header error, 0 address error, 0 unknown protocol 0 no route, 0 truncated, 9 discarded Sent: 17 total in 1104 bytes 17 generated, 0 forwarded 0 discarded Frags: 0 reassemble (0 reassembled, 0 couldn't reassemble) 0 fragment (0 fragmented, 0 couldn't fragment) 0 fragment created Mcast: 12 received in 1032 bytes 17 sent in 1104 bytes Bcast: 0 received, 0 sent IPv6 IC</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/igs-5225-16t4s/igs-5225-series-user-manual-catalan-english-french-dutch/page-388.html>PAGE 388</a></h6><p>Command Guide 4.21.59 show lacp Command: show lacp { internal | statistics | system-id | neighbour } show Show running system information lacp LACP configuration/status internal Internal LACP configuration neighbour statistics Neighbour LACP status Internal LACP statistics system-id LACP system id Default: N/A Usage Guide: To display the LACP mode information. Example: To display the LACP mode information.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/igs-5225-16t4s/igs-5225-series-user-manual-catalan-english-french-dutch/page-389.html>PAGE 389</a></h6><p>Command Guide Switch # show line alive Line is con 0. * You are at this line now. Alive from Console. Default privileged level is 2. Command line editing is enabled Display EXEC banner is enabled. Display Day banner is enabled. Terminal width is 80. length is 24. history size is 32. exec-timeout is 10 min 0 second. Current session privilege is 15. Elapsed time is 0 day 0 hour 17 min 20 sec. Idle time is 0 day 0 hour 0 min 0 sec. 4.21.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/igs-5225-16t4s/igs-5225-series-user-manual-catalan-english-french-dutch/page-390.html>PAGE 390</a></h6><p>Command Guide 4.21.62 show lldp med remote-device Command: show lldp med remote-device [ interface ( <port_type> [ <port_list> ] ) ] show Show running system information lldp Display LLDP neighbors information med Display LLDP-MED neighbors information remote-device interface Display remote device LLDP-MED neighbors information Interface to display Default: N/A Usage Guide: To display the LLDP-MED entries information. Example: To display the LLDP-MED entries information.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/igs-5225-16t4s/igs-5225-series-user-manual-catalan-english-french-dutch/page-391.html>PAGE 391</a></h6><p>Command Guide 4.21.64 show lldp statistics Command: show lldp statistics [ interface ( <port_type> [ <port_type_list> ] ) ] show Show running system information lldp Display LLDP neighbors information statistics Display LLDP statistics information interface Interface to display Default: N/A Usage Guide: To display the LLDP statistics information. Example: To display the LLDP statistics information for GigabitEthernet 1/1.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/igs-5225-16t4s/igs-5225-series-user-manual-catalan-english-french-dutch/page-392.html>PAGE 392</a></h6><p>Command Guide Usage Guide: To display the Syslog information. Example: To display the Syslog information with Log ID 235861. Switch # show logging 235861 Switch : 1 ID : 235861 Level : Warning Time : 1970-01-01T13:33:57+00:00 Message: Loop Detected: Port 5 shut down 4.21.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/igs-5225-16t4s/igs-5225-series-user-manual-catalan-english-french-dutch/page-393.html>PAGE 393</a></h6><p>Command Guide Transmit mode is enabled. No loop. The number of loops is 12390. Time of last loop is at 1970-01-01T14:58:28+00:00 Status is down. 4.21.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/igs-5225-16t4s/igs-5225-series-user-manual-catalan-english-french-dutch/page-394.html>PAGE 394</a></h6><p>Command Guide 4.21.68 show mep Command: show mep [ <instance> ] [ peer | cc | lm | dm | lt | lb | tst | aps | client | ais | lck ] [ detail ] show Show running system information mep Maintenance Entity Point <instance> The range of MEP instances ais Show AIS state aps Show APS state cc Show CC state client Show Client state detail Show detailed state including configuration information.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/igs-5225-16t4s/igs-5225-series-user-manual-catalan-english-french-dutch/page-395.html>PAGE 395</a></h6><p>Command Guide 4.21.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/igs-5225-16t4s/igs-5225-series-user-manual-catalan-english-french-dutch/page-396.html>PAGE 396</a></h6><p>Command Guide 4.21.70 show network-clock Command: show network-clock show Show running system information network-clock Show selector state Default: N/A Usage Guide: To display the SyncE information. Example: To display the SyncE information. Switch # show network-clock Selector State is: Free Run Alarm State is: Clk: 1 2 LOCS: FALSE FALSE SSM: FALSE FALSE WTR: FALSE FALSE LOL: DHOLD: FALSE TRUE SSM State is: Interface GigabitEthernet 1/1 Tx SSM QL_NONE Rx SSM Mode QL_LINK Master 4.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/igs-5225-16t4s/igs-5225-series-user-manual-catalan-english-french-dutch/page-397.html>PAGE 397</a></h6><p>Command Guide Default: N/A Usage Guide: To display the NTP Server information. Example: To display the NTP Server information. Switch # show ntp status NTP Mode : enabled Idx --1 Server IP host address (a.b.c.d) or a host name string -----------------------------------------------------192.168.0.44 2 3 4 5 4.21.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/igs-5225-16t4s/igs-5225-series-user-manual-catalan-english-french-dutch/page-398.html>PAGE 398</a></h6><p>Command Guide 4.21.73 show platform phy failover Command: show platform phy failover show Show running system information platform phy Platform specific information PHYs' information failover Failover status Default: N/A Usage Guide: To display the PHY failover status. Example: To display the PHY failover status. Switch # show platform phy failover Port Active Channel Broadcast ------ ------- --------- ---- After reset ------------ 4.21.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/igs-5225-16t4s/igs-5225-series-user-manual-catalan-english-french-dutch/page-399.html>PAGE 399</a></h6><p>Command Guide Example: To display the PHY ID for GigabitEthernet 1/1. Switch # show platform phy id interface GigabitEthernet 1/1 Port Channel ---- API Base ------- 1 0 -------0 (1g) Phy Id Phy Rev. ------8634 -----0 4.21.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/igs-5225-16t4s/igs-5225-series-user-manual-catalan-english-french-dutch/page-400.html>PAGE 400</a></h6><p>Command Guide port Show MAC Addresses learned by Port Security interface Search by port Default: N/A Usage Guide: To display the MAC Addresses of Port Security. Example: To display the MAC Addresses of Port Security. Switch # show port-security port interface GigabitEthernet 1/1 GigabitEthernet 1/1 ------------------MAC Address VID State ----------------- ---- ---------- Added ------------------------- Age/Hold Time ------------- <none> 4.21.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/igs-5225-16t4s/igs-5225-series-user-manual-catalan-english-french-dutch/page-401.html>PAGE 401</a></h6><p>Command Guide Interface Users State MAC Cnt ----------------------- ----- ------------- ------- GigabitEthernet 1/1 ---- No users 0 4.21.78 show privilege Command: show privilege show Show running system information privilege Display command privilege Default: N/A Usage Guide: To display the Privilege information. Example: To display the Privilege information. Switch # show privilege 4.21.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/igs-5225-16t4s/igs-5225-series-user-manual-catalan-english-french-dutch/page-402.html>PAGE 402</a></h6><p>Command Guide 1 GigabitEthernet 1/1, GigabitEthernet 1/2, GigabitEthernet 1/3, 4.21.80 show pvlan isolation Command: show pvlan isolation [ interface ( <port_type> [ <port_list> ] ) ] show Show running system information pvlan PVLAN configuration isolation show isolation configuration interface Search by port Default: N/A Usage Guide: To display the port isolation configuration. Example: To display the port isolation configuration.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/igs-5225-16t4s/igs-5225-series-user-manual-catalan-english-french-dutch/page-403.html>PAGE 403</a></h6><p>Command Guide dscp-classify dscp-cos Map for dscp classify enable Map for dscp to cos dscp-egress-translation Map for dscp egress translation dscp-ingress-translation Map for dscp ingress translation qce QoS Control Entry <qce> QCE ID wred Weighted Random Early Discard Default: N/A Usage Guide: To display the QoS configuration. Example: To display the QoS configuration for GigabitEthernet 1/1.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/igs-5225-16t4s/igs-5225-series-user-manual-catalan-english-french-dutch/page-404.html>PAGE 404</a></h6><p>Command Guide qos queue-policer queue 2 mode: disabled, rate: 500 kbps qos queue-policer queue 3 mode: disabled, rate: 500 kbps qos queue-policer queue 4 mode: disabled, rate: 500 kbps qos queue-policer queue 5 mode: disabled, rate: 500 kbps qos queue-policer queue 6 mode: disabled, rate: 500 kbps qos queue-policer queue 7 mode: disabled, rate: 500 kbps qos shaper mode: disabled, rate: 500 kbps qos queue-shaper queue 0 mode: disabled, rate: 500 kbps, excess: disabled qos queue-shaper queue 1 mode: disabled,</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/igs-5225-16t4s/igs-5225-series-user-manual-catalan-english-french-dutch/page-405.html>PAGE 405</a></h6><p>Command Guide 4.21.82 show radius-server Command: show radius-server [ statistics ] show Show running system information radius-server statistics RADIUS configuration RADIUS statistics Default: N/A Usage Guide: To display the RADIUS Server configuration. Example: To display the RADIUS Server configuration.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/igs-5225-16t4s/igs-5225-series-user-manual-catalan-english-french-dutch/page-406.html>PAGE 406</a></h6><p>Command Guide Switch # show rmon alarm 1 Alarm ID : 1 ---------------Interval : 30 Variable : .1.3.6.1.2.1.2.2.1.20.1 SampleType Value : deltaValue :0 Startup : risingOrFallingAlarm RisingThrld :2 FallingThrld :1 RisingEventIndex : 2 FallingEventIndex : 1 4.21.84 show rmon event Command: show rmon event [ <id_list> ] show Show running system information rmon RMON statistics event Display the RMON event table Default: N/A Usage Guide: To display the RMON Event configuration.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/igs-5225-16t4s/igs-5225-series-user-manual-catalan-english-french-dutch/page-407.html>PAGE 407</a></h6><p>Command Guide 4.21.85 show rmon history Command: show rmon history [ <id_list> ] show Show running system information rmon RMON statistics history Display the RMON history table Default: N/A Usage Guide: To display the RMON History configuration. Example: To display the RMON History ID 1 configuration. Switch # show rmon history 1 History ID : 1 -----------------Data Source : .1.3.6.1.2.1.2.2.1.1.5 Data Bucket Request : 50 Data Bucket Granted : 50 Data Interval : 1800 4.21.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/igs-5225-16t4s/igs-5225-series-user-manual-catalan-english-french-dutch/page-408.html>PAGE 408</a></h6><p>Command Guide Switch # show rmon statistics 1 Statistics ID : 1 --------------------Data Source : .1.3.6.1.2.1.2.2.1.1.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/igs-5225-16t4s/igs-5225-series-user-manual-catalan-english-french-dutch/page-409.html>PAGE 409</a></h6><p>Command Guide 'port' 'port-security' 'ptp' 'pvlan' 'qos' 'rmon' 'snmp' 'source-guard' 'ssh' 'upnp' 'user' 'vlan' 'voice-vlan' 'web-privilege-group-level' all-defaults Include most/all default values interface Show specific interface(s) vlan VLAN line Show line settings console vty Console VTY Default: N/A Usage Guide: To display the running-config. Example 1: To display the running-config. Switch # show running-config Building configuration...</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/igs-5225-16t4s/igs-5225-series-user-manual-catalan-english-french-dutch/page-410.html>PAGE 410</a></h6><p>Command Guide 4.21.88 show snmp Command: show snmp show Show running system information snmp Display SNMP configurations Default: N/A Usage Guide: To display the SNMP information. Example: To display the SNMP information Switch # show snmp SNMP Configuration SNMP Mode : enabled SNMP Version : 2c Read Community : public Write Community : private Trap Mode : disabled Trap Version :1 SNMPv3 Communities Table: Community Source IP : public : 0.0.0.0 Source Mask : 0.0.0.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/igs-5225-16t4s/igs-5225-series-user-manual-catalan-english-french-dutch/page-411.html>PAGE 411</a></h6><p>Command Guide SNMPv3 Groups Table; Security Model : v1 Security Name : public Group Name : default_ro_group Security Model : v1 Security Name : private Group Name : default_rw_group Security Model : v2c Security Name : public Group Name : default_ro_group Security Model : v2c Security Name : private Group Name : default_rw_group Security Model : v3 Security Name : default_user Group Name : default_rw_group SNMPv3 Accesses Table: Group Name : default_ro_group Security Model Security Le</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/igs-5225-16t4s/igs-5225-series-user-manual-catalan-english-french-dutch/page-412.html>PAGE 412</a></h6><p>Command Guide 4.21.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/igs-5225-16t4s/igs-5225-series-user-manual-catalan-english-french-dutch/page-413.html>PAGE 413</a></h6><p>Command Guide 4.21.90 show snmp community v3 Command: show snmp community v3 [ <community> ] show Show running system information snmp Display SNMP configurations community v3 Community SNMPv3 <community : word127> Specify community name Default: N/A Usage Guide: To display the SNMPv3 Community information. Example: To display the SNMPv3 Community information Switch # show snmp community v3 Community Source IP : public : 0.0.0.0 Source Mask : 0.0.0.0 Community Source IP : private : 0.0.0.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/igs-5225-16t4s/igs-5225-series-user-manual-catalan-english-french-dutch/page-414.html>PAGE 414</a></h6><p>Command Guide Default: N/A Usage Guide: To display the SNMP Host information. Example: To display the SNMP Host information Switch # show snmp host Trap Global Mode: Disabled 4.21.92 show snmp mib context Command: show snmp mib context show Show running system information snmp Display SNMP configurations mib MIB(Management Information Base) context MIB context Default: N/A Usage Guide: To display the SNMP MIB contexts. Example: To display the SNMP MIB contexts.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/igs-5225-16t4s/igs-5225-series-user-manual-catalan-english-french-dutch/page-415.html>PAGE 415</a></h6><p>Command Guide - ieee8021MstpMib (.1.3.111.2.802.1.1.6) IEEE8021-PAE-MIB : - ieee8021paeMIB (.1.0.8802.1.1.1.1) IEEE8023-LAG-MIB : - lagMIBObjects (.1.2.840.10006.300.43.1) IF-MIB : - ifMIB (.1.3.6.1.2.1.31) IP-FORWARD-MIB : - ipForward (.1.3.6.1.2.1.4.24) IP-MIB : - ipv4InterfaceTable (.1.3.6.1.2.1.4.28) - ipv6InterfaceTable (.1.3.6.1.2.1.4.30) - ipTrafficStats (.1.3.6.1.2.1.4.31) - ipAddressTable (.1.3.6.1.2.1.4.34) - ipNetToPhysicalTable (.1.3.6.1.2.1.4.35) - ipv6ScopeZoneIndexTable (.1.3.6.1.2.1.4.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/igs-5225-16t4s/igs-5225-series-user-manual-catalan-english-french-dutch/page-416.html>PAGE 416</a></h6><p>Command Guide - snmp (.1.3.6.1.2.1.5) - tcp (.1.3.6.1.2.1.6) - udp (.1.3.6.1.2.1.7) RMON-MIB : - statistics (.1.3.6.1.2.1.16.1) - history (.1.3.6.1.2.1.16.2) - alarm (.1.3.6.1.2.1.16.3) - event (.1.3.6.1.2.1.16.9) SMON-MIB : - switchRMON (.1.3.6.1.2.1.16.22) SNMP-FRAMEWORK-MIB : - snmpEngine (.1.3.6.1.6.3.10.2.1) SNMP-MPD-MIB : - dot1dTpHCPortTable (.1.3.6.1.2.1.17.4.5) - snmpMPDStats (.1.3.6.1.6.3.11.2.1) SNMP-USER-BASED-SM-MIB : - usmStats (.1.3.6.1.6.3.15.1.1) - usmUserTable (.1.3.6.1.6.3.15.1.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/igs-5225-16t4s/igs-5225-series-user-manual-catalan-english-french-dutch/page-417.html>PAGE 417</a></h6><p>Command Guide Example: To display the SNMP MIB ifIndex contexts.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/igs-5225-16t4s/igs-5225-series-user-manual-catalan-english-french-dutch/page-418.html>PAGE 418</a></h6><p>Command Guide 4.21.94 show snmp security-to-group Command: show snmp security-to-group [ { v1 | v2c | v3 } <security_name> ] show Show running system information snmp Display SNMP configurations security-to-group security-to-group configuration v1 v1 security model v2c v2c security model v3 v3 security model <securityname : word32> security group name Default: N/A Usage Guide: To display the SNMP Group information. Example: To display the SNMP Group information.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/igs-5225-16t4s/igs-5225-series-user-manual-catalan-english-french-dutch/page-419.html>PAGE 419</a></h6><p>Command Guide 4.21.95 show snmp user Command: show snmp user [ <username> <engineid> ] show Show running system information snmp Display SNMP configurations user User <username : word32> <engiedid : word10-32> Security user name Security Engine ID Default: N/A Usage Guide: To display the SNMP User information. Example: To display the SNMP User information.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/igs-5225-16t4s/igs-5225-series-user-manual-catalan-english-french-dutch/page-420.html>PAGE 420</a></h6><p>Command Guide Example: To display the SNMP viewer information. Switch # show snmp view View Name : default_view OID Subtree : .1 View Type : included 4.21.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/igs-5225-16t4s/igs-5225-series-user-manual-catalan-english-french-dutch/page-421.html>PAGE 421</a></h6><p>Command Guide Int. PathCost: 0 Max Hops : 20 TC Flag : Steady TC Count :0 TC Last :- Port Port Role --------- -------------- State ---------- --- Pri -------- PathCost ---- --- Edge ------------- 4.21.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/igs-5225-16t4s/igs-5225-series-user-manual-catalan-english-french-dutch/page-422.html>PAGE 422</a></h6><p>Command Guide 4.21.99 show tacacs-server Command: show tacacs-server show Show running system information tacacs-server TACACS+ configuration Default: N/A Usage Guide: To display the TACACS+ Server configuration. Example: To display the TACACS+ Server configuration. Switch # show tacacs-server Global TACACS+ Server Timeout : 5 seconds Global TACACS+ Server Deadtime : 0 minutes Global TACACS+ Server Key : No hosts configured! 4.21.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/igs-5225-16t4s/igs-5225-series-user-manual-catalan-english-french-dutch/page-423.html>PAGE 423</a></h6><p>Command Guide Alive from Console. Default privileged level is 2. Command line editing is enabled Display EXEC banner is enabled. Display Day banner is enabled. Terminal width is 80. length is 24. history size is 32. exec-timeout is 10 min 0 second. Current session privilege is 15. Elapsed time is 0 day 1 hour 12 min 15 sec. Idle time is 0 day 0 hour 0 min 0 sec. 4.21.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/igs-5225-16t4s/igs-5225-series-user-manual-catalan-english-french-dutch/page-424.html>PAGE 424</a></h6><p>Command Guide 4.21.102 show users Command: show users [ myself ] show Show running system information users Display information about terminal lines myself Display information about mine Default: N/A Usage Guide: To display the user status. Example: To display the user status for all. Switch # show users Line is con 0. * You are at this line now. Connection is from Console. User name is admin. Privilege is 15. Elapsed time is 0 day 1 hour 20 min 49 sec. Idle time is 0 day 0 hour 0 min 0 sec.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/igs-5225-16t4s/igs-5225-series-user-manual-catalan-english-french-dutch/page-425.html>PAGE 425</a></h6><p>Command Guide 4.21.103 show version Command: show version show Show running system information version System hardware and software status Default: N/A Usage Guide: To display the software and system information. Example: To display the software and system information.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/igs-5225-16t4s/igs-5225-series-user-manual-catalan-english-french-dutch/page-426.html>PAGE 426</a></h6><p>Command Guide 4.21.104 show vlan Command: show vlan [ id <vlan_list> | name <name> | brief ] show Show running system information vlan VLAN status id VLAN status by VLAN id name VLAN status by VLAN name brief VLAN summary information Default: N/A Usage Guide: To display the VLAN information. Example: To display the VLAN information. Switch # show vlan VLAN ---1 Name -------------------------------- Interfaces ---------- default Gi 1/1-25 10G 1/1-4 4.21.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/igs-5225-16t4s/igs-5225-series-user-manual-catalan-english-french-dutch/page-427.html>PAGE 427</a></h6><p>Command Guide Switch # show vlan ip-subnet VCE ID ------ IP Address --------------- 1 Mask Length ----------- 192.168.78.0 ---- VID Interfaces ---------- 24 5 GigabitEthernet 1/1 4.21.106 show vlan mac Command: show vlan mac [ address <mac_addr> ] show Show running system information vlan VLAN status mac Show VLAN MAC entries address Show a specific MAC entry Default: N/A Usage Guide: To display the MAC-based VLAN information. Example: To display the MAC-based VLAN information.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/igs-5225-16t4s/igs-5225-series-user-manual-catalan-english-french-dutch/page-428.html>PAGE 428</a></h6><p>Command Guide at Ether Type is AppleTalk ip Ether Type is IP ipx Ether Type is IPX llc LLC-based VLAN status <dsap> DSAP (Range: 0x00 - 0xFF) <ssap> SSAP (Range: 0x00 - 0xFF) snap SNAP-based VLAN status <oui> SNAP OUI (Range 0x000000 - 0XFFFFFF) rfc-1042 SNAP OUI is rfc-1042 snap-8021h <pid> SNAP OUI is 8021h PID (Range: 0x0 - 0xFFFF) Default: N/A Usage Guide: To display the Protocol-based VLAN information. Example: To display the Protocol-based VLAN information.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/igs-5225-16t4s/igs-5225-series-user-manual-catalan-english-french-dutch/page-429.html>PAGE 429</a></h6><p>Command Guide oui OUI configuration <oui> OUI value Default: N/A Usage Guide: To display the Voice VLAN information. Example: To display the Voice VLAN information for GigabitEthernet 1/1 Switch # show voice vlan interface GigabitEthernet 1/1 GigabitEthernet 1/1 : --------------------GigabitEthernet 1/1 switchport voice vlan mode is auto GigabitEthernet 1/1 switchport voice security is disabled GigabitEthernet 1/1 switchport voice discovery protocol is oui 4.21.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/igs-5225-16t4s/igs-5225-series-user-manual-catalan-english-french-dutch/page-430.html>PAGE 430</a></h6><p>Command Guide Switch # show web privilege group level Group Name Privilege Level CRO CRW SRO SRW Aggregation 6 10 5 Debug 15 15 15 DHCP 5 10 5 10 Dhcp_Client 5 10 5 10 Diagnostics 5 10 5 10 EPS 5 10 5 10 ERPS 5 10 5 10 ETH_LINK_OAM 5 10 5 10 EVC 5 10 5 10 Green_Ethernet 5 10 5 10 IP2 5 10 5 10 IPMC_Snooping 5 10 5 10 LACP 5 10 5 10 LLDP 5 10 5 10 Loop_Protect 5 10 5 10 MAC_Table 5 10 5 10 Maintenance 15 15 15 MEP 5 10 5</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/igs-5225-16t4s/igs-5225-series-user-manual-catalan-english-french-dutch/page-431.html>PAGE 431</a></h6><p>Command Guide 4.22 terminal 4.22.1 terminal editing Command: terminal editing terminal editing Set terminal line parameters Enable command line editing Default: Enabled Usage Guide: To enable editing mode for current terminal session. Example: To enable editing mode for current terminal session. Switch # terminal editing 4.22.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/igs-5225-16t4s/igs-5225-series-user-manual-catalan-english-french-dutch/page-432.html>PAGE 432</a></h6><p>Command Guide 4.22.3 terminal history size Command: terminal history size <history_size> terminal Set terminal line parameters history Control the command history function size Set history buffer size <history_size> Number of history commands, 0 means disable Default: N/A Usage Guide: To configure history buffer side for current terminal session. Example: To configure history buffer side with 20 lines for current terminal session. Switch # terminal history size 20 4.22.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/igs-5225-16t4s/igs-5225-series-user-manual-catalan-english-french-dutch/page-433.html>PAGE 433</a></h6><p>Command Guide 4.22.5 terminal width Command: terminal width <lines> terminal width Set terminal line parameters Set width of the display terminal <lines:0 or 40-512> Number of characters on a screen line (0 for unlimited width) Default: N/A Usage Guide: To configure width of command display for current terminal session. Example: To configure width of command display with 40 characters per line for current terminal session.</p></li></ul></nav></div></section></section></main><footer class=page-footer><div class="container flex-column py-3 py-sm-4"><div class="row mb-1 mb-sm-2 mb-md-5"><a href=/ class="brand offset-sm-0 col-sm-4 col-md-3 col-lg-2 offset-2 col-8 text-center text-md-start"><img class=logo-small src=/assets/img/brand-large.png alt=Manualshelf></a></div><div class=row><dl class="text-center text-sm-start col-sm-3"><dt class=fw-bold>Who We Are</dt><dd><a class=text-decoration-none href=/about>About Us</a></dd><dd><a class=text-decoration-none href=/company>Company</a></dd><dd><a class=text-decoration-none href=/careers>Careers</a></dd><dd><a class=text-decoration-none href=/terms>Terms & Privacy</a></dd></dl><dl class="text-center text-sm-start col-sm-3"><dt class=fw-bold>Resources</dt><dd><a class=text-decoration-none href=/brands>List of Manufacturers</a></dd><dd><a href=/ class=text-decoration-none>Support</a></dd><dd><a class=text-decoration-none href=/press>For the Press</a></dd><dd><a class=text-decoration-none href=/press#assets>Media assets</a></dd><dd><a class=text-decoration-none href=/faq>FAQ</a></dd></dl><dl class="text-center text-sm-start col-sm-3"><dt class=fw-bold>Get in touch</dt><dd><a class=text-decoration-none href=#>Blog</a></dd><dd><a class=text-decoration-none href=#>Email</a></dd><dd><a class=text-decoration-none href=/dmca>DMCA</a></dd></dl></div><div class=row><div class="text-center text-sm-start col-sm-4 pe-sm-0"><a href=https://www.facebook.com/pages/ManualShelf/1488826334681423 class="fs-5 text-center d-inline-block social rounded-2 align-middle text-decoration-none me-2"><i class="fab fa-facebook-f"></i></a><a href=https://www.twitter.com/ManualShelf class="fs-5 text-center d-inline-block social rounded-2 align-middle text-decoration-none me-2"><i class="fab fa-twitter"></i></a><a href=https://plus.google.com/+ManualShelf class="fs-5 text-center d-inline-block social rounded-2 align-middle text-decoration-none me-2"><i class="fab fa-google-plus-g"></i></a><a href=http://www.pinterest.com/ManualShelf class="fs-5 text-center d-inline-block social rounded-2 align-middle text-decoration-none"><i class="fab fa-pinterest-p"></i></a></div><div class="col col-sm-8 d-flex flex-column align-items-center flex-sm-row flex-wrap flex-sm-nowrap justify-content-center justify-content-sm-end"><div class="copy w-auto d-flex align-items-center justify-content-center justify-content-sm-end mt-2 mt-sm-0 me-2">ManualShelf © 2013-2025</div><select class="form-select form-select-sm w-auto mt-2 mt-sm-0"><option value=usa>USA</option></select><div></div></div><div id=pixel><script> googletag.cmd.push(function() { googletag.display('pixel'); }); </script></div></footer><script src=/assets/js/jquery-3.3.1.min.js></script><script src=/assets/js/bootstrap.bundle.min.js></script><script src=/assets/js/jquery.autocomplete.min.js></script><script type=text/javascript> $.extend({ redirectPost: function(location, args) { var form = ''; $.each(args, function(key, value) { form += '<input type="hidden" name="' + key + '" value="' + value + '">'; }); form = '<form id="s1" action="' + location + '" method="POST">' + form + '</form>'; $(document.body).append(form); $("#s1").submit(); } }); $(document).ready(function(){ $("#query").autocomplete({ minChars: 3, groupBy: 'type', paramName: 'q', dataType: 'json', serviceUrl: '/autocomplete', noCache: true, showNoSuggestionNotice: true, noSuggestionNotice: 'Zarro results found', onSelect: function (suggestion) { $.redirectPost(suggestion.data.url, {highlight: encodeURIComponent(JSON.stringify(suggestion.data.hls))}); } }); var toc = $('.toc-selector'); if (toc.length) { var slideParams = { duration: 800, easing: 'linear' }; toc.click(function() { $(this).toggleClass('open'); var section = $('.toc-content'); var isCollapsed = section.attr('data-collapsed') === 'true'; if (isCollapsed) { section.slideDown(slideParams) section.attr('data-collapsed', 'false') } else { section.slideUp(slideParams); section.attr('data-collapsed', 'true') } }); } }); var lastSmall = $(window).width() < 576; $(window).resize(function() { var newSmall = $(window).width() < 576; if (lastSmall != newSmall) { lastSmall = newSmall; window.location.href = window.location.href; } }); </script></body></html>