Industrial 4-Port 10/100/1000Base-T + 2-Slot 100/1000Base-X SFP Ethernet Switch IGS-620TF User's Manual
Trademarks Copyright © PLANET Technology Corp. 2013. Contents are subject to revision without prior notice. PLANET is a registered trademark of PLANET Technology Corp. other trademarks belong to their respective owners.
CE Mark Warning This is a Class A product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. WEEE Warning To avoid the potential effects on the environment and human health as a result of the presence of hazardous substances in electrical and electronic equipment, end users of electrical and electronic equipment should understand the meaning of the crossed-out wheeled bin symbol.
Table Of Contents 1. Introduction............................................................................... 5 1.1 Package Contents................................................................ 5 1.2 How to Use This Manual....................................................... 5 1.3 Product Features.................................................................. 6 1.4 Product Specifications.......................................................... 8 1.5 Physical Dimensions...........................
1. Introduction 1.1 Package Contents Check the contents of your package for the following parts: ll Industrial Gigabit Ethernet Switch x 1 ll User's Manual x 1 ll DIN Rail Kit x 1 ll Wall Mount Kit x 1 If any of these are missing or damaged, please contact your dealer immediately; if possible, retain the carton including the original packing material, and use them again to repack the product in case there is a need to return it to us for repair.
Chapter 6 Cable Connection Parameters The chapter contains the cable connection parameters of the Industrial Gigabit Ethernet Switch. Appendix A This chapter contains cable information of the Industrial Gigabit Ethernet Switch. 1.3 Product Features Physical Port 4-Port 10/100/1000Base-T RJ-45 with auto MDI / MDI-X function 2 SFP interfaces, 100/1000Base-X dual mode (DIP switch control) Layer 2 Features IEEE 802.3 / 802.3u / 802.3ab / 802.
DIN Rail and Wall Mount Design Redundant Power Design - 12 to 48V DC, redundant power with polarity reverse protect function - AC 24V power adapter acceptable Supports EFT protection for 6000 VDC for power line Supports 6000 VDC Ethernet ESD protection -40 to 75 degrees C operating temperature Fiber Port Redundancy Link status auto-detect and redundant on Dual ports with the same connector type Only when Primary-Port is active, the Backup-Port is blocked.
1.4 Product Specifications Model IGS-620TF Hardware Specification 10/100/1000Base-T Ports 4 SFP Interfaces 2 1000Base-SX/LX/BX SFP interfaces (Port-5 and Port-6) Compatible with 100Base-FX SFP Dimensions (W x D x H) 135 x 87 x 32mm Weight 503g Power Requirements DC 12~48V, Redundant power with polarity reverses protection function. AC 24V Power Adapter Power Consumption / Dissipation 7.
Network Cables 10/100/1000Base-T : Cat. 3, 4, 5, 5e, 6 UTP cable (100meters, max.) EIA/TIA-568 100-ohm STP (100meters, max.) 1000Base-SX : 50/125μm or 62.5/125μm multi-mode fiber optic cable, up to 550m (vary on SFP module) 1000Base-LX : 9/125μm single-mode fiber optic cable, up to 10/20/30/40/50/70/120 kilometers (vary on SFP module) 100Base-FX : 50/125μm or 62.
1.
2. Installation This section describes the functionalities of the Industrial Gigabit Ethernet Switch’s components and guides how to install it on the desktop. Basic knowledge of networking is assumed. Please read this chapter completely before continuing. 2.1 Product Description Flexibility and Network Distance Extension Solution The IGS-620TF Industrial Gigabit Ethernet Switch is equipped with four 10/100/1000Base-T auto-negotiation ports and two 100/1000X SFP slots.
traffic control cabinets. It also possesses an integrated power supply source with wide range of voltages (12 to 48V DC or 24V AC) for worldwide high availability applications requiring dual or backup power inputs. Being able to operate under the temperature range from -40 to 75 degrees C, the IGS-620TF can be placed in almost any difficult environment. The compact, IP-30 standard metal case of IGS-620TF allows either DIN rail or wall mounting for efficient use of cabinet space.
2.1.1 Switch Front Panel Figure 2-1 shows a front panel of Industrial Gigabit Ethernet Switch.
2.1.2 LED Indicators System LED Color Function P1 Green Lit: indicate power 1 has power. P2 Green Lit: indicate power 2 has power. FAULT Green Lit: indicate either power 1 or power 2 has no power. Per 10/100/1000T Ports LED Color 100 LNK/ACT 1000 LNK/ACT Function Orange Lit: indicate the link through that port is successfully established at 100Mbps or 10Mbps. Blink: indicate that the Switch is actively sending or receiving data over that port.
2.1.3 Switch Upper Panel The upper panel of the Industrial Gigabit Ethernet Switch consists of one terminal block connector within two DC power inputs, and also provides 3 DIP Switches for 100/1000X fiber support on two SFP slots and fiber redundant function. Figure 2-2 shows the upper panel of the Industrial Gigabit Ethernet Switch.
2.1.4 Wiring the Power Inputs The 6-contact terminal block connector on the top panel of Industrial Gigabit Ethernet Switch is used for two DC redundant power inputs. Please follow the steps below to insert the power wire. 1000X Switch 100FX 3 Redundant 2 Mode 1 Port 6 1 2 3 4 5 6 Port 6 OFF 1000X ON 100FX Input DC 12~48V, AC 24V Fiber Mode Insert positive / negative DC power wires into the contacts 1 and 2 for POWER 1, or 5 and 6 for POWER 2.
2.1.5 Wiring the Fault Alarm Contact The fault alarm contacts are in the middle of the terminal block connector as the picture shows below. Inserting the wires, the Industrial Gigabit Ethernet Switch will detect the fault status of the power failure and then forms an open circuit. The following illustration shows an application example for wiring the fault alarm contacts.
The Industrial Gigabit Ethernet Switch has two SFP interfaces that support 100/1000 dual speed mode (Optional Multi-mode / Singlemode 100Base-FX / 1000Base-SX/LX SFP module) through DIP switch setting. Cabling Each 10/100/1000Base-T port uses RJ-45 sockets -- similar to phone jacks -- for connection of unshielded twisted-pair cable (UTP). The IEEE 802.3 / 802.3u / 802.3ab Fast / Gigabit Ethernet standard requires Category 5 UTP for 100Mbps 100Base-TX. 10Base-T networks can use Cat.
MGB / MFB Series Transceiver Figure 2-3: Plug-in the SFP Transceiver Approved PLANET SFP Transceivers PLANET Industrial Gigabit Ethernet Switch supports 100/1000 dual mode with both Single mode and Multi-mode SFP transceivers.
MGB-LB40 SFP-Port 1000Base-LX (WDM, TX:1550nm) mini-GBIC module - 40km MGB-TSX SFP-Port 1000Base-SX mini-GBIC module - 550m (-40~75°C) MGB-TLX SFP-Port 1000Base-LX mini-GBIC module - 10km (-40~75°C) MGB-TL30 SFP-Port 1000Base-LX mini-GBIC module - 30km (-40~75°C) MGB-TL70 SFP-Port 1000Base-LX mini-GBIC module - 70km (-40~75°C) Fast Ethernet SFP Transceiver Modules MFB-FX SFP-Port 100Base-FX Transceiver (1310nm) - 2km MFB-F20 SFP-Port 100Base-FX Transceiver (1310nm) - 20km MFB-F40 SFP-Port 100
1. Set the DIP Switch of SFP Port 1 or Port 2 to the “OFF” position with fiber speed 1000Base-X. ON OFF Port 5 (DIP 1) 100FX 1000X Port 6 (DIP 2) 100FX 1000X 2. Make sure both sides of the SFP transceiver are with the same media type, for example: 1000Base-SX to 1000Base-SX, 1000Base-LX to 1000Base-LX. 3. Check whether the fiber-optic cable type matches with the SFP transceiver model.
2. Make sure both sides of the SFP transceiver are with the same media type or WDM pair, for example, 100Base-FX to 100Base-FX, 100Base-BX20-U to 100Base-BX20-D. 3. Check whether the fiber-optic cable type matches with the SFP transceiver model. To connect to MFB-FX SFP transceiver, use the multi-mode fiber cable, with one side being the male duplex LC connector type.
Note Never pull out the module without pulling the lever or the push bolts on the module. Directly pulling out the module with violence could damage the module and the SFP module slot of the Industrial Gigabit Ethernet Switch. 2.1.7 Redundancy Overview The Industrial Gigabit Ethernet Switch provides rapid fiber redundancy of link for highly critical Ethernet applications. The redundant-mode supports auto-recover function.
2.2 Mounting Installation This section describes how to install the Industrial Gigabit Ethernet Switch and make connections to it. Please read the following topics and perform the procedures in the order being presented. Note In the installation steps below, this Manual uses IGS801(PLANET 8 Port Industrial Gigabit Switch) as the example. However, the steps for PLANET Industrial Switch & Industrial Media Converter are similar. 2.2.
1 2 Step 2: Lightly insert the DIN-Rail into the track. Step 3: Make sure the DIN-Rail is tightly secured on the track. Step 4: Please refer to the following procedures to remove the Industrial Gigabit Ethernet Switch from the track.
1 2 Step 5: Lightly pull out the bottom of the DIN-Rail from the track to remove. 2.2.2 Wall Mount Plate Mounting To install the Industrial Gigabit Ethernet Switch on the wall, please follow the instructions described below. Step 1: Remove the DIN-Rail from the Industrial Gigabit Ethernet Switch; loose the screws to remove the DIN-Rail. Step 2: Place the wall mount plate on the rear panel of the Industrial Gigabit Ethernet Switch.
3. Applications In this paragraph, we will describe how to install the Industrial Gigabit Ethernet Switch.
Harsh Climate Weather Station IP Camera Desert IP Camera IP Camera IGS-620TF 120km IP Camera 1000 IGS-620TF 30km 1000 Fiber Switch 70km Data Center 30km 1000 1000 IGS-620TF 1000 IP Camera IP Camera 30km IGS-620TF 30km 120km 1000 1000 IGT-1205AT Winter Season of Country 30km 1000 IGT-1205AT Steel Factory IGS-620TF 100Base-TX UTP 1000 28 1000Base-SX/LX Fiber-optic
Installation Steps Step 1: Unpack the Industrial Gigabit Ethernet Switch. Step 2: Check whether the DIN-Rail is screwed on the Industrial Gigabit Ethernet Switch. (Please refer to DIN-Rail Mounting section for DIN-Rail installation if the DIN-Rail is not screwed on the Industrial switch). If you want to wall mount the Industrial Gigabit Ethernet Switch, then please refer to the Wall Mount Plate Mounting section for wall mount plate installation.
4. Switch Operation 4.1 Address Table The Industrial Gigabit Ethernet Switch is implemented with an address table. This address table is composed of many entries. Each entry is used to store the address information of some node in network, including MAC address, port no, etc. This information comes from the learning process of Industrial Gigabit Ethernet Switch. 4.
checking before transmission. Therefore, no error packets will occur. It is the best choice when a network needs efficiency and stability. The Industrial Gigabit Ethernet Switch scans the destination address from the packet-header, searches the routing table provided for the incoming port and forwards the packet, only if required. The fast forwarding makes the switch attractive for connecting servers directly to the network, thereby increasing throughput and availability.
5. Troubleshooting This chapter contains information to help you solve issues. If the Industrial Gigabit Ethernet Switch is not functioning properly, make sure the Industrial Gigabit Ethernet Switch was set up according to instructions in this manual. The per port LED is not lit Solution: Check the cable connection of the Industrial Gigabit Ethernet Switch. Performance is bad Solution: Check the speed duplex mode of the partner device.
6. Cable Connection Parameters The wiring details are as below: 100FX Fiber Optical Cables: Standard Fiber Type Cable Specification 100Base-FX (1300nm) Multi-mode 50/125μm or 62.5/125μm 100Base-FX (1310nm) Multi-mode 50/125μm or 62.5/125μm Single-mode 9/125μm 100Base-BX-U (TX : 1310/RX : 1550) 100Base-BX-D (TX : 1550/RX : 1310) Single-mode 9/125μm 1000X Fiber Optical Cables: Standard Fiber Type Cable Specification 1000Base-SX (850nm) Multi-mode 50/125μm or 62.
APPENDIX A: Networking Connection A.
A.2 RJ-45 Cable Pin Assignments The standard RJ-45 receptacle/connector There are 8 wires on a standard UTP/STP cable and each wire is colorcoded.
EC Declaration of Conformity For the following equipment: *Type of Product : *Model Number : * Produced by: Manufacturer Name Manufacturer Address Industrial 4-Port 10/100/1000T + 2 100/1000Base-X SFP Ethernet Switch (-40~75 degrees C) IGS-620TF : Planet Technology Corp. : 10F., No.96, Minquan Rd., Xindian Dist., New Taipei City 231, Taiwan (R.O.C.
