User's Manual
- 9 -
- 10 -
- 11 -
- 12 - - 13 - - 14 -
2. Tighten the wire-clamp screws for preventing the wires from
loosening.
1 2
Power
+ -
Note
1. The wire gauge for the terminal block should be in
the range between 12 and 24 AWG.
2. The DC power input range is 9V ~ 48V DC or 24V
AC.
4.3 SideWall-mountPlateMounting
Caution
You must use the screws supplied with the wall-
mounting brackets. Damage caused to the parts by
using incorrect screws would invalidate your warranty.
4.4 GroundingtheDevice
User MUST complete grounding wired with the device; otherwise,
a sudden lightning could cause fatal damage to the device. EMD
(Lightning) DAMAGE IS NOT CONVERED UNDER WARRANTY.
V+
PWR
DC Input: 9-48V
, 0.5A max.
AC Input: 24V
, 0.2A max.
1 2
Earth Ground
4.HardwareInstallation
This section describes the functionalities of the Industrial Media
Converter’s components and guides you to installing it on the DIN
rail and wall. Please read this chapter completely before continuing.
Note
This following pictures guide you to installing the
device, and the device is not IGT-815AT.
4.1 DIN-railMountingInstallation
2
1
4.2 Wall-mountPlateMounting
5.FiberandCopperInstallation
The IGT-815AT is exible enough to extend the distance from
220m to 120km. It depends on the 1000BASE-X or 100BASE-FX
SFP transceivers. The SFP transceivers are hot-pluggable and
hot-swappable. You can plug in and out the transceiver to/from
any SFP port without having to power down the Industrial Media
Converter.
DC
Power Line (DC)
1000BASE-SX/LX Fiber-optic
1000
1000BASE-T UTP
550m / 20km 100m
DC 9~48V
IGT-815AT
DC
Data
Power
Data
IP Camera
Monitoring
Center
1000
Fiber Switch
6.LinkFaultPassthrough
The LFP function includes Link Loss Carry Forward (LLCF), Link
Loss Return (LLR) and the DIP switch design. LLCF and LLR can
immediately alert administrators about the issue of the link media
and provide ecient solution to monitor the network. The DIP
switch provides the disabling or enabling of the LFP function.
IP Camera
LFP
Enabled
LFP
Enabled
Copper Cable Copper Cable
Monitoring Center
IP Camera
Fiber Cable
LFP
Enabled
LFP
Enabled
Copper Cable
Copper Cable
Monitoring Center
Copper Link Broken
1
Copper
Link Down
5
LFP disconnects
Fiber Link
2
LFP disconnects
Copper Link
4
Fiber Link Down
3
1000
1000
Fiber Cable
Remote Link
Broken
Remote Link
Normal
1000BASE-SX/LX Fiber-optic
1000
1000BASE-T UTP
Note
LFP function is turned off by default. This feature
can also be turned on via the DIP switch. If you are
not familiar with the network installation and for
diagnostic purpose (i.e. check which end is broken),
you can turn it on. Otherwise, please keep it in the
default position.
CustomerSupport
Thank you for purchasing PLANET products. You can browse our
online FAQ resource on PLANET web site rst to check if it could
solve your issue. If you need more support information, please
contact PLANET switch support team.
PLANET online FAQs:
http://www.planet.com.tw/en/support/faq.php
Switch support team mail address:
support_switch@planet.com.tw
Copyright © PLANET Technology Corp. 2021.
Contents are subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp.
All other trademarks belong to their respective owners.