000BASE-X to 10/100/1000BASE-T 802.
Table of Contents 1. Introduction............................................................................... 5 1.1 Package Contents................................................................ 5 1.2 How to Use This Manual....................................................... 5 1.3 Product Features.................................................................. 6 1.4 Product Specifications.......................................................... 8 1.5 Physical Dimensions...........................
Trademarks Copyright © PLANET Technology Corp. 2018. Contents are subject to revision without prior notice. PLANET is a registered trademark of PLANET Technology Corp. All other trademarks belong to their respective owners. Disclaimer PLANET Technology does not warrant that the hardware will work properly in all environments and applications, and makes no warranty and representation, either implied or expressed, with respect to the quality, performance, merchantability, or fitness for a particular purpose.
communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. CE Mark Warning This is a Class A product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.
1. Introduction 1.1 Package Contents Check the contents of your package for the following parts: uuIndustrial 802.3at PoE Media Converter x 1 uuUser’s Manual x 1 uuDIN-rail Kit x 1 uuWall Mounting Kit x 1 uuRJ45 Dust Cap x 1 uuSFP Dust Cap x 1 If any of these are missing or damaged, please contact your dealer immediately, if possible, retain the carton including the original packing material, and use them again to repack the product in case there is a need to return it to us for repair.
Chapter 5 Cable Connection Parameters The chapter explains the cable connection parameters of the Industrial 802.3at PoE Media Converter. Appendix A This chapter contains cable information of the Industrial 802.3at PoE Media Converter. 1.3 Product Features Physical Port 1-port 10/100/1000BASE-T RJ45 with IEEE 802.3af/802.
Hardware LED Indicators –System: Power 1, Power 2 and Fault LED –Fiber port: LNK/ACT –10/100/1000BASE-T port: LNK/ACT, 1000, PoE-in-use DIP switch: LFP (Link Fault Passthrough) mode selection Industrial Case and Installation IP30 metal case DIN-rail and wall-mount design 12 ~ 48V DC/24V AC redundant power with polarity reverse protect function and connective removable terminal block for master and slave power Supports 6000 VDC Ethernet ESD protection -40 to 75 degrees C operating temper
1.4 Product Specifications Product IGTP-802T IGTP-802TS IGTP-805AT Ethernet Interface Copper 10/100/1000BASE-T Ethernet TP interface. Maximum 100m distance. Auto-negotiation, auto MDI/MDI-X with PoE injector function 1000BASE-X Fiber-optic Connector Type SC SC Fiber Cable Multi-mode: 50/125µm or 62.5/125µm optic fiber Single-mode: 9/125µm optic fiber Fiber Cable Distance 220m & 550m 10km Fiber Optical Frequency 850nm 1310nm Launch Power Max. -4dBm Min. -9.5dBm Max. -3dBm Min. -9.
Hardware Specifications Speed Twisted-pair: 10/20Mbps for half/full duplex 100/200Mbps for half/full duplex 1000/2000Mbps for full duplex Fiber Optic: 200Mbps / 2000Mbps for full duplex Flow Control Back pressure for half duplex mode IEEE 802.
Alarm Provides one relay output for power failure Alarm relay current carry ability: 1A @ DC 24V Cables 10/100/1000BASE-T: 2-pair UTP Cat. 3, 4, 5, 5e, 6 (maximum 100 meters) EIA / TIA-568 100-ohm STP (maximum 100 meters) 100BASE-FX/1000BASE-SX/LX: Multi-mode: 50/125μm or 62.
1.5 Physical Dimensions IGTP-80xT Industrial 802.3at PoE (W x D x H): 135 x 87 x 32 mm Media Converter dimensions IGTP-802T/IGTP-802TS: 163.00 40.00 28.00 18.00 Mounting Kit 28.00 48.80 DIN-Rail Kit Mounting Kit 28.00 28.00 Rear View 107.00 Top View 87.80 IGTP-802T Ethernet+DC LNK/ ACT 1000 PoEin-Use ON OFF LFP 10/100/1000T TX RX LNK/ ACT Bottom View Input DC12~48V, AC 24V 10.90 1000BASE-SX/LX Fault 15.20 P1 PWR2 V2+ V2- 30.00 Fault Front View V1+ V1- PWR1 135.
PWR1 PWR2 V2+ V2- Front View Fault Input DC12~48V, AC 24V 12 V1+ V1- Bottom View Top View Rear View Side View Dimensions ( unit = mm ) Mounting Kit DIN-Rail Kit Mounting Kit IGTP-805AT: 163.
2. Installation This product provides three different running speeds – 10Mbps, 100Mbps and 1000Mbps in the same Industrial 802.3at PoE Media Converter and automatically distinguishes the speed of incoming connection; this section describes the functionalities of IGTP-80xT’s components and guides how to install it on the DIN Rail Basic knowledge of networking is assumed. Please read this chapter completely before continuing. 2.
With the long fiber distance support, the IGTP-80xT still sustains the transmission performance as high as 1000Mbps. It works in the highperformance Store and Forward mechanism, and also can prevent packet loss with IEEE 802.3x flow control and the LFP (Link Fault Passthrough) function in the DIP switch design. Furthermore, it can immediately alarm the administrators the issue from the link media and provide efficient solution to monitor the network power usage. Complying with the IEEE 802.
2.1.1 Product Overview The Front Panel of the Industrial 802.3at PoE Media Converter consists of one 1000BASE-SX/1000BASE-LX/100/1000BASE-X mini-GBIC SFP port and one Auto-sensing 10/100/1000Mbps Ethernet RJ45 Port. Figure 2-1 & 2-2 shows a front panel of Industrial 802.3at PoE Media Converter. 2.1.2 Converter Front Panel Figure 2-1 & 2-2 shows the front panel of Industrial 802.3at PoE Media Converter.
2.1.3 LED Indicators System: LED Color Function P1 Green Lit: indicates power 1 has power. P2 Green Lit: indicates power 2 has power. FAULT Green Lit: indicates either power 1 or power 2 has no power. Gigabit Fiber Interface LED Fiber LNK/ ACT Color Green Function Lit: indicates that the Fiber Optical Port is successfully connecting to the network at 1000Mbps (IGTP-802T/IGTP-802TS), at 100Mbps/1000Mbps (IGTP-805AT). Blinks: indicates the fiber optical port is receiving or sending data.
2.1.4 Converter Upper Panel The upper panel of the Industrial 802.3at PoE Media Converter consists of one terminal block connector within two DC power inputs. Figure 2-3 shows the upper panel of the Industrial 802.3at PoE Media Converter. 1 2 3 4 5 6 V1+ V1PWR1 V2+ V2PWR2 Fault Input DC12~48V, AC 24V Figure 2-3: Industrial 802.3at PoE Media Converter Upper Panel 2.1.5 Wiring the Power Inputs The 6-contact terminal block connector on the top panel of Industrial 802.
2. Tighten the wire-clamp screws for preventing the wires from loosening. 1 2 Power 1 + - 3 Fault 4 5 6 Power 2 + - 1. The wire gauge for the terminal block should be in the range between 12 and 24 AWG. Note 2. The DC power input range is 12V ~ 48V DC and supports 24V AC. 3. Please just use one power input when using 24V AC. 2.1.6 Wiring the Fault Alarm Contact The fault alarm contacts are in the middle of the terminal block connector as the picture shows below.
1. The wire gauge for the terminal block should be in the range of 12 ~ 24 AWG. Note 2. Alarm relay circuit accepts up to 30V, max. 3A currents. Fault Alarm Contacts Fault The Fault Alarm Contacts are energized (CLOSE) for normal operation and will OPEN when failure occurs 2.2 Mounting Installation This section describes how to install the Industrial 802.3at PoE Media Converter and make connections to it. Please read the following topics and perform the procedures in the order being presented.
2.2.1 DIN-rail Mounting The DIN-rail bracket is screwed on the Industrial Equipment when out of factory. Please refer to the following figures to screw the DIN-rail bracket on the Industrial Equipment. To hang the Industrial Equipment, follow the steps below: Step 1: Screw the DIN-rail bracket on the Industrial 802.3at PoE Media Converter. 1 2 Step 2: Lightly push forward the lower part of the DIN-rail bracket into the track.
Step 3: Check whether the DIN-rail bracket is tightly on the track. Step 4: Please refer to the following procedure to remove the Industrial 802.3at PoE Media Converter from the track. 1 2 Step 5: Lightly pull out the lower part of the DIN-rail bracket to remove it from the track.
2.2.2 Wall-mount Plate Mounting To install the Industrial 802.3at PoE Media Converter on the wall, please follow the instructions described below. Step 1: Remove the DIN-rail bracket from the Industrial 802.3at PoE Media Converter; loosen the screws to remove the DIN-rail bracket. Step 2: Place the wall-mount plate on the rear panel of the Industrial 802.3at PoE Media Converter. Step 3: Use the screws to screw the wall-mount plate on the Industrial 802.3at PoE Media Converter.
2.2.3 Fiber Installation IGTP-802T/IGTP-802TS 1000BASE-X Installation: To install an Industrial 802.3at PoE Media Converter stand-alone, on a Track or wall mount, simply complete the following steps: Step 1: Turn off the DC power of the device/station in a network to which IGTP-802T/IGTP-802TS will be attached. Step 2: Ensure that there is no activity in the network. Step 3: Attach fiber cable from the Industrial 802.3at PoE Media Converter to the fiber network. TX, RX must be paired at both ends.
IGTP-805AT 100/1000BASE-X Installation: The IGTP-805AT is flexible enough to extend the distance from 220m to 120km. It depends on the 100M/1000M mini GBIC modules. The SFP transceivers are hot-plug and hot-swappable. You can plug in and out the transceiver to/from any SFP port without having to power down the Industrial 802.3at PoE Media Converter. To install IGTP-805AT with 100BASE-FX, 1000BASE-SX/LX SFP, simply complete the following steps: Step 1: Slot in the 100BASE-FX, 1000BASE-SX/LX SFP.
The following list the available Modules for IGTP-805AT. Gigabit Ethernet Transceiver (1000BASE-X SFP) Model Speed (Mbps) Connector Interface Fiber Mode Distance Wavelength (nm) Operating Temp.
Gigabit Ethernet Transceiver (1000BASE-BX, Single Fiber Bi-directional SFP) Model Speed Connector Fiber Wavelength Wavelength Operating Distance (Mbps) Interface Mode (TX) (RX) Temp.
Fast Ethernet Transceiver (100BASE-BX, Single Fiber Bi-directional SFP) Model Speed Connector Fiber Wavelength Wavelength Operating Distance (Mbps) Interface Mode (TX) (RX) Temp. 100 WDM (LC) Single 20km Mode 1310nm 1550nm 1550nm 1310nm MFB-TFA20 100 MFB-TFB20 WDM (LC) Single 20km Mode 1310nm 1550nm 1550nm 1310nm MFB-TFA40 100 MFB-TFB40 WDM (LC) Single 40km Mode 1310nm 1550nm 1550nm 1310nm MFB-FA20 MFB-FB20 0 ~ 60 degrees C -40 ~ 75 degrees C -40 ~ 75 degrees C 2.2.4 802.
3. Link Passthrough Function The LFP function includes the Link Fault Passthrough function (LLCF/ LLR) and the DIP Switch design. LLCF/LLR can immediately alarm administrators the issue of the link media and provide efficient solution to monitor the net. The DIP Switch provides disable or enable the LFP function. LLCF (Link Loss Carry Forward) means when a device is connected to the converter and the TP line loses the link, the converter’s fiber will disconnect the transmission link.
If the connection breaks, the IGTP-80xT whose link is lost forwards to the switch/hub which generates a trap to the management station. The administrator can then determine the source of the issue. Management Station Switch/Hub w/SNMP Media Converter Media Converter LFP ON TP LED lit = established link Note Switch/Hub w/SNMP Management Station LFP ON Broken Fiber Cable TP LED unlit = no link The converter is shipped with the default LFP (LLCF/ LLR) function disabled.
Management Station Switch/Hub w/SNMP Media Converter Media Converter LFP ON Switch/Hub Station LFP OFF Fiber Cable LED lit = established link LED unlit = no link If one of the optical conductors is bad (as shown in the diagram box below), the converter with LLR enabled will return a no-link condition to its link partner.
4. Troubleshooting This chapter contains information to help you solve issues. If the IGTP-80xT is not functioning properly, make sure the IGTP-80xT was set up according to instructions in this manual. The Power LED is not lit Solution: Check the power cable connection between power adapter and IGTP-80xT. Why did connecting the IGTP-80xT to device with 1000BASELX/SX interface and the 1000BASE-LX/SX fiber fail? Solution: Please check if the fiber connection between two devices is correct.
5. Cable Connection Parameter The wiring details are shown below: 100FX Fiber Optical Cables: Standard Fiber Type Cable Specification 100BASE-FX (1300nm) Multi-mode 50/125μm or 62.5/125μm Multi-mode 50/125μm or 62.5/125μm 100BASE-FX (1310nm) Single-mode 9/125μm 100BASE-BX-U (TX: 1310nm/RX: 1550nm) Single-mode 9/125μm 100BASE-BX-D (TX: 1550nm/RX: 1310nm) 1000X Fiber Optical Cables: Standard Fiber Type Cable Specification 1000BASE-SX (850nm) Multi-mode 50/125μm or 62.
Appendix A: Networking Connection A.
A.2 RJ45 Cable Pin Assignments The standard RJ45 receptacle/connector There are 8 wires on a standard UTP/STP cable and each wire is colorcoded.
EC Declaration of Conformity For the following equipment: *Type of Product : 1000BASE-SX/LX to 10/100/1000BASE-T 802.3at PoE Industrial media converter *Model Number : IGTP-805AT、IGTP-802T、IGTP-802TS * Produced by: Manufacturer‘s Name : Planet Technology Corp. Manufacturer‘s Address : 10F., No.96, Minquan Rd., Xindian Dist., New Taipei City 231, Taiwan, R.O.C.
