User's Manual

- 9 -
- 10 -
- 11 -
- 12 - - 13 - - 14 -
4.HardwareInstallation
This section describes the functionalities of the Industrial PoE+
Media Converter’s components and guides you to installing it on
the DIN rail and wall. Please read this chapter completely before
continuing.
Note
This following pictures guide you to installing the
device, and the device is not IGTP-815AT.
4.1 DIN-railMountingInstallation
2
1
4.4 GroundingtheDevice
User MUST complete grounding wired with the device; otherwise,
a sudden lightning could cause fatal damage to the device. EMD
(Lightning) DAMAGE IS NOT CONVERED UNDER WARRANTY.
V+
PWR
DC Input:
48-56V
, 0.9A max.
1 2
Earth Ground
4.2 Wall-mountPlateMounting
4.3 SideWall-mountPlateMounting
Caution
You must use the screws supplied with the wall-
mounting brackets. Damage caused to the parts by
using incorrect screws would invalidate your warranty.
5.FiberandPoEInstallation
The IGTP-815AT is exible enough to extend the distance from
220m to 120km. It depends on the 1000BASE-X or 100BASE-FX
SFP transceivers. The SFP transceivers are hot-pluggable and
hot-swappable. You can plug in and out the transceiver to/from any
SFP port without having to power down the Industrial 802.3at PoE+
Media Converter.
If there is any IEEE 802.3at/802.3af devices needed to power on,
the IGTP-815AT can provide you a way to supply power for this
Ethernet device conveniently and easily.
The IGTP-815AT needs DC 48-56V input and it injects the DC
power into the pin of the twisted pair cable (Pins 1, 2, 3 and 6).
DC
Power Line (DC)
1000BASE-SX/LX Fiber-optic
1000
PoE
1000BASE-T UTP with PoE
550m / 20km 100m
DC 48~56V
IGTP-815AT
DC
Power
Data
Power
Data
PoE
IP Camera
PoE
Monitoring
Center
1000
Fiber Switch
6.LinkFaultPassthrough
The LFP function includes Link Loss Carry Forward (LLCF), Link
Loss Return (LLR) and the DIP switch design. LLCF and LLR can
immediately alert administrators about the issue of the link media
and provide ecient solution to monitor the network. The DIP
switch provides the disabling or enabling of the LFP function.
PoE
IP Camera
LFP
Enabled
LFP
Enabled
Copper Cable
PoE
Copper Cable
Monitoring Center
PoE
IP Camera
Fiber Cable
LFP
Enabled
LFP
Enabled
Copper Cable
PoE PoE
Copper Cable
Monitoring Center
Copper Link Broken
1
Copper
Link Down
5
LFP disconnects
Fiber Link
2
LFP disconnects
Copper Link
4
Fiber Link Down
3
1000
1000
Fiber Cable
Remote Link
Broken
Remote Link
Normal
Note
LFP function is turned off by default. This feature
can also be turned on via the DIP switch. If you are
not familiar with the network installation and for
diagnostic purpose (i.e. check which end is broken),
you can turn it on. Otherwise, please keep it in the
default position.
CustomerSupport
Thank you for purchasing PLANET products. You can browse our
online FAQ resource on PLANET web site rst to check if it could
solve your issue. If you need more support information, please
contact PLANET switch support team.
PLANET online FAQs:
http://www.planet.com.tw/en/support/faq.php
Switch support team mail address:
[e-mail]
Copyright © PLANET Technology Corp. 2021
Contents are subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp.
All other trademarks belong to their respective owners.