Internet Telephony PBX System IPX-1900 User’s manual Version 1.0.
Copyright Copyright (C) 2008 PLANET Technology Corp. All rights reserved. The products and programs described in this User’s Manual are licensed products of PLANET Technology, This User’s Manual contains proprietary information protected by copyright, and this User’s Manual and all accompanying hardware, software, and documentation are copyrighted.
Revision User’s Manual for PLANET Internet Telephony PBX System: Model: IPX-1900 Rev: 1.0 (June, 2008) Part No. EM-IPX1900 Series V1.
Table of Contents Chapter 1 ................................................................................................ 6 Introduction............................................................................................ 6 Overview............................................................................................................................6 Package Content ...............................................................................................................
Chapter 5 Management ....................................................................... 57 Admin Account ...............................................................................................................57 Date & Time .............................................................................................................58 Ping Test ...................................................................................................................59 Save & Restore .....................
Chapter 1 Introduction 1 Overview PLANET IPX-1900 IP PBX telephony systems are designed and optimized for the small business in daily communications. The IPX-1900 are able to accept 300 user registrations, and easy to install and manage a fully working system with the convenience and cost advantages.
IP PBX Features • PBX Features Automated Attendant (AA) Interactive Voice Responses (IVR) Voicemail support (VM) Call Detailed Record (CDR) User Management via Web Browsers Display 300 Registered User’s Status: Unregistered / Registered / On-Call Multiple Service Providers Lines / SIP Accounts (30) Simultaneous Trunk Links: 30 concurrent trunk calls SIP Trunk / Gateway Trunk / FXO Trunk Management Two-stage / One-stage call to Trunk by Trunk Group Configuration Build in 2 / 4 FXO PSTN trunk (Modular) By ad
Front Panel Indicators Figure 1-1. Front Panel of IPX-1900 Front Panel LED PWR SYS LAN WAN FXO/FXS Port State Descriptions On PBX Power ON Off PBX Power OFF On System is booting Flashing System is ready On LAN is connected successfully Flashing Data is transmitting Off Ethernet not connected to PC On PBX network connection established Flashing Data traffic on cable network Off Waiting for network connection On Port is busy Flashing Ring indication.
The 3 WAN WAN port supports auto negotiating Fast Ethernet 10/100Base-TX networks. This port allows your IP PBX to be connected to an Internet Access device, e.g. router, cable modem, ADSL modem, through a CAT.5 twisted pair Ethernet cable. 4 LAN The LAN port allows your PC or Switch/Hub to be connected to the IP PBX through a CAT.5 twisted pair Ethernet cable. 2 external slosts with compliance FXO/FXS module. FXO module is connects to PBX or CO line with RJ-11(Write) analog line.
Chapter 2 Preparations & Installation 2 Physical Installation Requirement This chapter illustrates basic installation of IP PBX • Network cables. Use standard 10/100Base-TX network (UTP) cables with RJ45 connectors. • TCP/IP protocol must be installed on all PCs.
ÍNote In order to connect machine for administration, please locate your PC in the same network segment (192.168.0.x) of IP PBX. If you’re not familiar with TCP/IP, please refer to related chapter on user’s manual CD or consult your network administrator for proper network configurations. Network Interface quick configurations Wizard is a tool to quickly setup IP PBX. After pass the authentication, please click for quick IPX PBX setup. For most users, Internet access is the primary application.
¾ Step2. NAT Setting LAN IP Setting Private IP address for connecting to a local private network. LAN IP Address (Default: 192.168.0.1) Subnet mask for the local private network (Default: Subnet Mask 255.255.255.0) Enable to open LAN port DHCP server DHCP Server Assigned DHCP IP Address DHCP IP Lease Time DHCP server range from start IP to end IP Client to ask DHCP server refresh time, range from 60 to 86400 seconds Table 2-2. LAN IP description of IP PBX Figure 2-3. Wizard-NAT settings ¾ Step4.
Figure 2-4. Wizard-IP PBX settings Service Provider: Caller ID Service provider name Username Input Provider name Password Input Provider password Host Input Providers server address Port Providers server port Table 2-3. Service provider description User Extensions: User Extension Password Caller Id Input Extension number Input Extension password Input Extension caller id Table 2-4.
Figure 2-5. Wizard-Rebooting ÍNote Please consult your ISP personnel to obtain proper PPPoE/IP address related information, and input carefully. If Internet connection cannot be established, please check the physical connection or contact the ISP service staff for support information. RS-232 Console Port Configuration RS-232 port (DB-9pin Female connector), Configure the COM Port Properties as following: Bits per second: 57600, Flow control: None 1. Connect Gateway RS-232 port to PC COM Port. 2.
4. Create new connection. Select “COM” port that connect PC to gateway Figure 2-7. Hyper Terminal Screen 5. Make connection(Bits Pre second:57600 Flow contact: None) 6. Input “Enter” and Show Welcome display. 7. Login, input the Password to login.(Password as the same as Access, default is admin) 8.
Chapter 3 IP PBX Setup SIP Basic Setting 3 SIP (Session Initiation Protocol) is a request-response protocol, dealing with requests from clients and responses from servers. Participants are identified by SIP URLs. Requests can be sent through any transport protocol. SIP determines the end system to be used for the session, the communication media and media parameters, and the called party's desire to engage in the communication.
Max Registration Time Min Registration Time Maximum duration of incoming registration/subscriptions we allow. Default 3600 seconds. Minimum duration of registrations/subscriptions. Default 60 seconds Default Incoming/Outgoing Default duration (in seconds) of incoming / outgoing registration. Registration Time Min RoundtripTime Minimum roundtrip time for messages to monitored hosts, Defaults (T1 Time) to 200 ms Language Set default language for all users.
Register TimeOut Register Attempts Retry registration calls at every 'x' seconds (default 20). Number of registration attempts before we give up; 0 = continue forever. Table 3-2. Outbound DIP registration description ¾ NAT Support The externip, externhost and localnet settings are used if you use IP PBX behind a NAT device to communicate with services on the outside. Figure 3-4. NAT support settings Extern IP Address that we're going to put in outbound SIP messages if we're behind a NAT.
User Extensions Setup ¾ Extension List Figure 3-5. User extension settings Advance Click to edit an extension other setting. Delete Click to delete an extension. Table 3-5. User extension description ¾ Advance Setup Figure 3-6.
User Extension Input Extension number Password Input Extension password Caller Id Input Extension caller id Table 3-5. Extension advance description - Call group / Pickup group select : Call Group An Extension can set single/multiple call group(s) 1-10 id Pickup Group An Extension can set single/multiple Pickup group(s) 1-10 id Table 3-6. Call / Pickup group description - Call forward option : DND(Forward to Voice mail) Enable / Disable forward to voice mail.
Figure 3-7. Server Providers Setting ¾ Add New Service Providers Step 1. Press “Add” button to add an new service provider information. Figure 3-8. Add new service providers Step 2. Fill in the required information in Service Provider Advance Setup page. Figure 3-9. Service provider advance setup Caller id The caller ID will be sent between the callee and caller and will be displayed on SIP device LCD panel for identification.
Registrar Server Port Port number of SIP Register Server. Assigns a value from 1024 to 65535, the common default SIP port is 5060. Outbound Proxy server’s IP address / Domain name. Assign a Outbound Proxy Address server’s IP / Domain name which is in charge of call-out service. Outbound Proxy Port Port number of Outbound Proxy Server. Assign a number from 1024 to 65535, the common default SIP port setting is 5060.
Press “Advance” to Edit an FXO Prot as below Figure 3-11. FXO Trunk list Figure 3-12. FXO Advance setting Port Num Caller id Analog Port Number (System Define) The caller ID will be sent between the callee and caller and will be displayed on SIP device LCD panel for identification. Any calls originating from the registered ITSP to IP PBX will go into the DID auto-attendant or direct to the selected user or hunting group. Table 3-13.
Trunk Management – Gateway Trunk Gateway Trunk Setting allows IP PBX makes VoIP calls to external Gateway by peer-to-peer mode. If the FXO ports of external Gateway have connected with PSTN lines, the user can make outgoing PSTN calls via external Gateway by this function. Figure 3-13. Gateway Trunk setting IP Destination IP Address is the IP address of the destination Gateway that owns this phone number. Port Port is port of the destination Gateway use. (Default is 5060) Table 3-11.
¾ Add New Trunk Group Step 1. Press “Add” button to add an new Group Name information. Figure 3-17. Add an new Group Name Step 2. Fill in the required information in Trunk Group Setup page. Figure 3-18. Trunk Group Setup Group Name Number All Trunk Trunk Group The Trunk Group name If the leading digits are match with this number, IP PBX will delete this number and send out the following digits. It will show all the available SIP Trunks and Gateway Trunks for selection.
One-Stage Call: 1. If user dials 81123456, this call will hunt SIP_Trunk_1 and send 123456 to call out. 2. If user dials 82234567, this call will hunt SIP_Trunk_2 and send 234567 to call out. 3. If user dials 0345678, this call will hunt FXO_Gateway and send 345678 to call out. Two-Stage Call: 1. If user dials 81 and hear the dial tone, then dial 123456. This call will hunt SIP_Trunk_1 and send 123456 to call out. 2. If user dials 82 and hear the dial tone, then dial 234567.
¾ Scenario Sample Example I: Phone Pattern Figure 3-21. Dialing Rules list - 1 1. 1N (N: single digit from 2~9, excl. 0 and 1) In this example, when the caller (User/IP-Phone) dial the number range from “12 to 19” , iPBX / WiPBX will send the call to SIP Proxy Server 2. 2Z (Z: single digit from 1~9, excl. 0) In this example, when the caller (User/IP-Phone) dial the number range from “21 to 29” , iPBX / WiPBX will send the call to SIP Proxy Server 3.
2. When User / IP-Phone call “0943123123”, iPBX will automatically dial “0943123123” to SIP Proxy Server. 3. When User / IP-Phone call “43123123”, iPBX will automatically dial “0943123123” to SIP Proxy Server. How to setting call out by SIP trunk / FXO (PSTN)trunk / Gateway trunk ? Step 1. Create SIP Trunk or Gateway Trunk 1.1 For example create 4 SIP Trunk accounts to register ITSP. Figure 3-23. SIP provider list 1.2 For example create 4 Gateway Trunk IP Address and Port Figure 3-24.
Figure 3-25 IP PBX Trunk group - 1 2.
Step 3.
¾ Sample: Figure 3-29. Auto-attendant sample Attendant Message The Attendant Message on the IPBX systems, it is can auto-answer attendant message setting on the attendant time, IPBX message can play voice to SIP Trunk and Gateway's FXO, and FXS port. Figure 3-30. Auto-attendant message Attendant Message Advance Setting : Figure 3-31.
G.11( .gsm ) You can upload gsm format voice file to IPBX. Associate a dial number with a call group voice Service Number instruction to instruct incoming calls Specificity the call group hunting. Ext/Hunt Group Table 3-14. Attendant Messages setup description Attendant Time Defined Attendant Time on the IPBX systems, it is can answer attendant message to match on the attendant time. Figure 3-32. Auto-attendant time list Attendant Time Advance Setting : Figure 3-33.
Day Setting Defined Start Day / End Day. Time Setting Defined Start Time / End Time. Month Setting: Defined Start Month / End Month . Date Setting Defined Start Date / End Date. Message Select play voice message. Defined the Auto Attendant Service Method. Auto Attendant Service Method a). Always play attendant messages b). Always goto EXT/HuntGroup c). User try error goto EXT/HuntGroup Table 3-15.
Upload Voice File This page allows transfer music on hold file or PBX Voice Files from your PC to IPBX. Figure 3-35. On-hold voice uploads Click Browse and select your file, then click upload to finish. Figure 3-36. Answer extension voice upload Answer extension Call from registered IP-Phone to record the voice menu. Sound File Select G.711 Voice file, then click play to your registered device. Table 3-18.
Extension to Dial for Parking Calls Set an extension number to dial when need to park the call. Default number is 700. What extension to park calls on Set the Extension range for call parking retrieving. (Example: '701-720'). Number of seconds a call can be Set allowed parking time for the parking call. Default is parked for Pickup Extension 30/sec. Set up a number for IP Phone to retrieve back the call. Default is *8. Timeout for answer on attended Set a timeout value for answer the transferred call.
¾ Transfer Feature Figure 3-39. Transfer feature settings Attendant Transfer Blind Transfer Transfer Digit time out When you attendant transfer fail, you can definition other transfer number Blind Transfer , When Ex: Ext 100 call Ext 200, Ext 200 blind transfer to Ext 300 , Ignore the Ext.300 status, the Ext.200 will immediately on-hook Set (Attendant/blind) transfer digit time out sec Table 3-22 Transfer feature description ¾ Pickup Key Figure 3-25.
¾ SMTP Setting SMTP is a relatively simple, text-based protocol, where one or more recipients of a message are specified. Input the valid account number, the extension setting voice mail will be been in used. Figure 3-41. SMTP settings SMTP server IP / Address Input server IP / Address SMTP Authentication user name Input SMTP Authentication user name SMTP Authentication password Input SMTP Authentication password From Email Input your Email, if server to check your email address. Table 3-24.
Figure 3-43. Hunt Group list Figure 3-42. Hunt Group more information ¾ Add New Hunt Group Step 1. Press “Add” button to add a new Group Name information. Figure 3-43. Add an new Group Name Step 2. Fill in the required information in Hunt Group Setup page. Figure 3-44. Hunt Group setup Group Name Input your group name There are 3 modes available: Round Robin / Ring All / Random Mode. 1. Round Robin: Take turns ringing each available Hunt Mode Extension / Users 2.
A, when the caller dial “20”, all extensions under Group A will ring). Default incoming call dial number is empty. Ring (Group/Extension) Setup a timeframe to control the call group hunting timeout. Timeout Default setting is 30 sec. Table 3-25. Hunt Group description ¾ To add extension/users to Ring group Step 1.Select your extension Figure 3-45. Add Extension/User Step 2. Press to add extension/users to ring group. Figure 3-46.
Chapter 4 Network Setup WAN & LAN Setup 4 WAN (Wide Area Network) is a network connection connecting one or more LANs together over some distance. For example, the means of connecting two office buildings separated by several kilometers would be referred to as a WAN connection. The size of a WAN and the number of distinct LANs connected to a WAN is not limited by any definition. Therefore, the Internet may be called a WAN.
¾ Static IP If you are a leased line user with a fixed IP address, enter in the IP address, subnet mask, gateway address, and DNS (domain name server) address(es) provided to you by your ISP. Each IP address entered in the fields must be in the appropriate IP form, which are four IP octets separated by a dot (x.x.x.x). The Router will not accept the IP address if it is not in this format. Example: 168.95.1.2 Figure 4-2. WAN-Static IP settings IP Address Check with your ISP provider.
Figure 4-3. WAN-DHCP settings ¾ PPPoE Point-to-Point Protocol over Ethernet (PPPoE). Some ISPs provide DSL-based services and use PPPoE to establish communication link with end-users. If you are connected to the Internet through a DSL line, check with your ISP to see if they use PPPoE. If they do, you need to make sure the following items, PPPoE User name: Enter username provided by your ISP. PPPoE Password: Enter password provided by your ISP. Figure 4-4.
called www.IP-PBX.com. When we need to find the host name from an IP address we send a request to the host using its IP address. The host will respond with its host name. ¾ WAN Port MAC The MAC (Media Access Control) Address field is required by some Internet Service Providers (ISP). The default MAC address is set to the MAC address of the WAN interface in the device. It is only necessary to fill the field if required by your ISP.
Figure 4-6. MTU and MRU settings ÍNote For Static IP, both MTU and MRU are set to 1500 bytes as default value. For DHCP, both MTU and MRU are set to 1500 bytes as default value. For PPPoE, both MTU and MRU are set to 1492 bytes as default value. ¾ DNS Server DNS stands for Domain Name System. Every Internet host must have a unique IP address; also they may have a user-friendly, easy to remember name such as www.ippbx.com. The DNS server converts the user-friendly name into its equivalent IP address.
¾ LAN Setting These are the IP settings of the LAN (Local Area Network) interface for the device. These settings may be referred to as "private settings". You may change the LAN IP address if needed. The LAN IP address is private to your internal network and cannot be seen on the Internet. The default IP address is 192.168.0.1 with a subnet mask of 255.255.255.0. LAN is a network of computers or other devices that are in relatively close range of each other.
Expired Time of the DHCP lease for each client computer. DHCP Server is a useful tool that automates the assignment of IP addresses to numbers of computers in your network. The server maintains a pool of IP addresses that you use to create scopes. (A DHCP scope is a collection of IP addresses and TCP/IP configuration parameters that are available for DHCP clients to lease.
Static Route Static routes are special routes that the network administrator manually enters into the router configuration for local network management. You could build an entire network based on static routes. The problem with doing this is that when a network failure occurs, the static route will not change without you performing the change. This could be IP-PBX if the failure occurs when the administrator is not available.
Figure 4-13. NAT settings ¾ NAT Setting Figure 4-14. NAT settings Network Address Translation Enable/Disable NAT. IPsec (Internet Protocol Security) is a framework for a set of protocols for IPSec Pass Through security at the network or packet processing layer of network communication. Enable/Disable this framework verification.
L2TP (The Layer 2 Tunnel Protocol) is an emerging Internet Engineering Task Force (IETF) standard that combines the best features of two existing tunneling protocols: Cisco's Layer 2 Forwarding (L2F) and L2TP Pass Through Microsoft's Point-to-Point Tunneling Protocol (PPTP). L2TP is an extension to the Point-to-Point Protocol (PPP), which is an important component for VPNs. VPNs allow users and telecommuters to connect to their corporate intranets or extranets. Enable/Disable this function.
Figure 4-15. Virtual server mapping settings Enable Enable/Disable the virtual server mapping, default setting is Disable. The port number on the WAN side that will be used to access the WAN Port virtual service. Enter the WAN Port number, e.g. enter 80 to represent the Web (http server), or enter 25 to represent SMTP (email server). Note: You can specify maximum 32 WAN Ports. Protocol The protocol used for the virtual service. Select a protocol type is TCP or UDP.
Trigger Type This is the protocol used to trigger the special application. This is the port number on the WAN side that will be used to access Public Port the application. You may define a single port or a range of ports. You can use a comma to add multiple ports or port ranges. Public Type This is the protocol used for the special application. Action Insert a new Port Trigger or update a specified Port Trigger. Table 4-8.
Block Day Time Wan IP Port Block time setting. Select Always or By Schedule. Block Day setting, select a All / Mon-Sat./ Mon-Fri./Mon./ Tues./ Wed./Thu./Fri./Sat./Sun. Block Time setting, select time range is 00:00 to 23:59. Table 4-9. Packet filter-WAN description ¾ LAN LAN Enable/Disable Internet to LAN filter function, default setting is Enable. A prohibitive rule set should only allow the necessary Internet/DMZ services to LAN (Local Area Network) clients.
Figure 4-18. URL filter settings Enable/Disable the URL filter function, default setting is Enable Disable. Enable/Disable Block URL to the Clinet IP, default setting is Enable Disable This is the Clinet IP is LAN address. Example: Client IP 192.168.0.100 URL Filter String This is the filter URL. Example: “http://www.yahoo.com/” Table 4-12.
UPnP UPnP provides support for communication between control points and devices. The network media, the TCP/IP protocol suite and HTTP provide basic network connectivity and addressing needed. On top of these open, standard, Internet based protocols, UPnP defines a set of HTTP servers to handle discovery, description, control, events, and presentation. Figure 4-20. UPnP settings UPNP Internet Gate Enable/Disable UPNP Service to working, default Device setting is Disable. Table 4-18.
Figure 4-21. DDNS settings Enable DDNS Server Type Enable/Disable the DDNS service, default setting is Disable. The IP-PBX support two types of DDNS, DynDns.org or No-IP.com DDNS Username The username which you register in DynDns.org or No-IP.com website. DDNS Password Confirmed Password Hostname to register The password which you register in DynDns.org or No-IP.com website. Confirm the password which you typing. The hostname which you register in DynDns.org or No-IP.com website Table 4-14.
. Figure 4-22. SNMP settings Enable Enable/Disable the SNMP service, default setting is Disable. (Support SNMP version 1 or SNMP version 2c). SNMP Read Community SNMP Read Community string so that EPICenter can retrieve information.(default :public) Specifies the name of the SNMP write community to which SNMP Write Community the printer device that this actual destination represents belongs.(Default:private) SNMP Trap Host Defines an SNMP trap host to which AppCelera will send trap messages.
Chapter 5 Management Admin Account 5 The administrator account can access the management interface through the web browser. Figure 5-1. Management settings Assign a name to represent the administrator account. Maximum 16 Administrator Name characters. Legal characters can be the upper letter “A” to “Z”, lower letter “a” to “z”, digit number “0” to “9” and an underscore sign¡ ”_”. Assign an administrator password.
ÍNote z z The administrator name and password are case-sensitive and the “blank” character is an illegal character Only the administrator account has the ability to change account password. Date & Time ¾ Manual Time Setting Figure 5-2. Date/Time-Manual time settings Manual Time Setting Set up the time manually. Table 5-2. Date/Time-Manual time description ¾ NTP Time Server Figure 5-3.
Time Zone Choose your time zone, Default is (GMT+8:00) Beijing, Singapore, Taipei. Enable / Disable. Default is Disabling, time during which clocks Daylight Saving are set one hour ahead of local standard time; widely adopted during summer to provide extra daylight in the evenings. NTP Update Interval Default is 24 hours; This is used to select the frequency of. NTP updates. NTP Server 1 Default is “pool.ntp.org”, NTP Server address. NTP Server 2 Default is empty. Table 5-3.
Factory Default This function is used to restore all the parameters back to factory default setting. You can use the Save/Restore Setting to check the factory default configuration, after you click on the Set button. Figure 5-6. Factory default settings Firmware Update You can upgrade the firmware of the device using this tool. Make sure that the firmware you want to use is saved on the local hard drive of your computer.
Chapter 6 Information System Information 6 System Information page indicates the current setup-status of the device, it includes LAN, WAN, (Status and MAC Address), Host Name / System Date time / Machines Life time and system firmware information. The information and options on this page will vary according to your WAN setting (Static IP, DHCP, or PPPoE). -If your WAN connection is set up for Dynamic IP address, the page will display “Release” and “Renew” buttons.
PBX Extension Status This page displays the information of Extension/Users Registration status. Figure 6-2. Extension Status SIP device is connected to IPPBX Register OK The connection from/to the other end of SIP device is Talk on the telephone established. Register Unknown Sip device is not connected to IPPBX Table 6-1. Extension Status description PBX Trunk Status This page displays the information of Service Provider Registration status. Figure 6-3.
Call Detail Record Call Detail Record (CDR) contains the call history of the extensions when calls was made or received. Recorded information include: Source Number, Destination Number, Start Time, Answer Time, End Time, Duration Time and Status. Figure 6-4.
Appendix A How to use Call Parking function The followings are the Call Park function settings, and all of VoIP devices (ATA, GW and IP Phone) were registered with Wi-Fi IP PBX. ¾ Extension to Dial for Parking Calls: 700 ¾ Extensions to park calls on :701-720 Figure A-1. Call Parking sample scenario 1. Ext.100 and Ext.300 are talking. 2. Ext.300 press Transfer button and dial “700#” to carry out the Call Parking function, and the voice guide will tell Ext.
Appendix B How to use Call Pick-up function The followings are the Call Pickup function settings, and all of VoIP devices (ATA, GW and IP Phone) were registered with IP PBX. ¾ Pickup Extension: *8 Figure B-1. Call Pickup sample scenario 1. Ext.300 call to Ext.100, and Ext.100 is ringing. 2. Ext.200 dial “*8#” to pickup the call for Ext.100, and Ext.200 is talking with Ext.300.
Appendix C Record Sound Sample This sample for how to record sound, as gsm format file for ipbx series use. A) Visit to www.nch.com.au sound home-page, to download Wavepad v3.05 (for windows) sound tools install your pc. B) In this screen, create a new file, Input 8000Hz and select mono (Single) channel then press ok to finish. C) Press F5 Select your recording sound device and record channel or recording volume level.
D) Press Start recording E) Save the current file as WAV or gsm format to finish. ¾ Convert Wav to G729 format Example A) Visit to www.voiceage.com home-page, to download Open G729 encoder sound tools uncompress to your pc. B) Convert WAV format file to g729 format file.
Appendix D Record Voice Guide Process IPX-1900 provides Record Voice Menu by Phone function. Please register your VoIP devices to Wi-Fi IP PBX at first, and then check the Record voice code from “IP PBX Setup -> record Voice Menu” page. Figure C-1. Record voice menu settings VoIP devices dial *9 to entry the Record Voice Menu, then refer to the following record processes to record the Voice Menu. Figure C-2.
Appendix E Voice Communication Samples The chapter shows you the concept and command to help you configure your IP PBX System through sample configuration. And provide several ways to make calls to desired destination in IP PBX. In this section, we’ll lead you step by step to establish your first voice communication via web browsers operations. IP Phone register to IPX-1900 In the following samples, we’ll introduce IP Phone register to IP PBX applications.
STEP 2: Click the “Add” button to create extension account ext.100 and ext.101. Figure D-4. Add extension setting of IP PBX STEP 3: Please log in VIP-254T_B and browser to “SIP setting Æ Domain Service” configuration menu. Insert the account/password information then save and reboot machine. The sample configuration screen is shown below: Data match with Figure D-3. IP PBX’s extension settings The IP address of IP PBX Figure D-5.
STEP 5: After both of devices have registered to IP PBX successfully, it could browse to “Information -> PBX Extension Status” page to show the registration status: Figure D-8. Extension status ¾ Test the Scenario: 1. VIP-254T_B pick up the telephone 2. Dial the number: 100 shall be able to connect to the VIP-254T_A 3. Then the VIP-254_A should ring.
¾ Machine Configuration: STEP 1: Please refer to the first sample and let VIP-154T and VIP-192 register to IP PBX. STEP 2: Please log in IP PBX via web browser and browse to “IP PBX Setup Æ User Extensions Setup” configuration menu to add four accounts for VIP-480FO using. Figure D-10. Add accounts for VIP-480FO STEP 3: Browse to “IP PBX Setup Æ Attendant Extension” configuration menu.
STEP 4: Browse to “IP PBX Setup Æ Trunk Management Æ Gateway Trunk” configuration menu. Fill in the IP address of VIP-480FO for connecting with VIP-480FO by peer-to-peer mode, and press the “Insert” button for activate the configuration. Figure D-12. Add a Gateway trunk for connecting with VIP-480FO STEP 5: Browse to “IP PBX Setup Æ Trunk Management Æ Trunk Group” configuration menu. Add a Trunk Group for making off-Net calls via VIP-480FO. Figure D-13.
Figure D-15. Set up the Hunting Member of FXO ports Figure D-16. Set up the Proxy Server IP address for register to IPX-1900 STEP 7: Browse to “Dialing Plan” configuration menu. Add an Incoming Dial Plan (no.1x) for redirect the PSTN outgoing calls to FXO ports. Figure D-17. Add an incoming dial plan STEP 8: Browse to “Port Status” configuration menu. Fill in the auto attendant number 555 to all of ports.
Figure D-18. Hot Line to auto-attendant of IPX-1900 STEP 8: After all of devices have registered to IP PBX successfully, the Extension Status page will show the registration status: Figure D-19. Extension status page with Phone and Gateway registered ¾ Test the Scenario: 1. VIP-154T pick up the telephone 2. Dial the number: 0 will hear the dial tone, and dial the number: 12345678. This call will hunt the FXO port of VIP-480FO and shall be able connect to the User A. 3.
IP Phone make external SIP Proxy calls via SIP Trunk In the following samples, we’ll introduce VIP-154T and VIP-192 makes SIP Proxy calls via SIP Trunk applications. Figure D-20. Installation example with FWD SIP Prxoy ¾ Machine Configuration: STEP 1: Please refer to the first sample and let VIP-254T and VIP-255PT register to IP PBX. STEP 2: Browse to “IP PBX Setup Æ Trunk Management Æ SIP Trunk” configuration menu. Add a new Service Provider account for registering to FWD SIP Proxy. Figure D-21.
STEP 3: Browse to “IP PBX Setup Æ Trunk Management Æ Trunk Group” configuration menu. Add a Trunk Group for making external SIP Proxy calls. Figure D-22. Add Trunk Group number STEP 4: After the SIP Trunk has registered to FWD SIP Proxy successfully, the Service Provider Status page will show the registration status: Figure D-23. Service Provider status page ¾ Test the Scenario: 1. VIP-154T pick up the telephone 2. Dial the number: 9 will hear the dial tone, and dial the number: 25003999.
Appendix F IPX-1900 Series Specifications Product Internet Telephony PBX System Model IPX-1900 Hardware LAN WAN Standards and Protocol 1 RJ-45 (10/100Base-TX, Auto-Sensing/Switching) 1 RJ-45 (10/100Base-TX, Auto-Sensing/Switching) Call control SIP 2.0 (RFC3261) , SDP (RFC 2327), Symmetric RTP Registration Max. 300 nodes / SIP IP phones/ ATA / FXO gateways Calls Max. 60 concurrent calls Voice CODEC Support G.723, G.726, G.729, G.
Internet Sharing Protocol TCP/IP, UDP/RTP/RTCP, HTTP, ICMP, ARP, NAT, DHCP, PPPoE, DNS NAT/Bridge mode, DHCP server, Static Route, DMZ, Virtual Server, Port Advanced Function Trigger, Packet / URL Filter, UPnP, DDNS, SNMP, Ping test Network and Configuration Connection Type Static IP, PPPoE, DHCP Management HTTP Web Browser System: 1, PWR WAN: 1, LNK/ACT LED Indications LAN: 4, LNK/ACT Line: 4, In-Use/Ringing Environment Dimension (W x D x H) 340 x 159 x 40 mm Operating Temperature 0~40 degree C, 0~90%
Appendix G IPX-1900 Module Card Specifications IPX-19FO Card Technical Specifications Signaling Loop Start / DTMF No. of channels 2 Interface Connectors 2 RJ-11 2-pin modular jacks AC Impedance Selection 600 Ω /900 Ω / Global Impedance / Sixteen Impedance for selection. Receive Frequency Response Low –3 dBFS Corner, FILT = 0 , 5 Hz Return Loss digital gain/attenuation adjustment Tranhybrid Balance Low –3 dBFS Corner, FILT = 1, 200 Hz ≥ 25 dB , 300–3.4 kHz, all ac terminations –16.5 to 13.
FXO Port Pin Assignments The FXO Telephony Interface has 2 RJ-11C/W modular jacks. The following diagram and table show the assignments of the pin for the R-J11 port. RJ-11pin Signal 1 2 Tip 3 Ring 1 2 3 4 4 FXS Port Pin Assignments The FXS Telephony Interface has 4 RJ-11C/W modular jacks. The following diagram and table show the assignments of the pin for the RJ-11 port.
EC Declaration of Conformity For the following equipment: *Type of Product *Model Number : Internet Telephony PBX system : IPX-1900 * Produced by: Manufacturer‘s Name : Manufacturer‘s Address: Planet Technology Corp. 11F, No 96, Min Chuan Road Hsin Tien, Taipei, Taiwan, R. O.C. is herewith confirmed to comply with the requirements set out in the Council Directive on the Approximation of the Laws of the Member States relating to 1999/5/EC R&TTE.