User's Manual

- 10 - - 12 - - 13 - - 14 -
- 9 - - 11 -
Step 2: Refer to the picture below to screw the four screws on the wall.
140.00mm
129.00mm
60.00mmØ4.50mm
Ø7.00mm
Step 3: Use a screwdriver to screw them into the wall.
3.4 Grounding the Device
Users MUST complete grounding wired with the device; otherwise, a
sudden lightning could cause fatal damage to the device.
Earth Ground
4.ProductSpecications
Product IPOE-175S
Hardware Specications
Interface
Input Port
1 x 10/100/1000BASE-T Ethernet with
IEEE 802.3bt PoE++
“PoE + Data” in RJ45 port
Output Port
1 x 10/100/1000BASE-T
“Data” out RJ45 port
Output Power
Terminal Block
1 x 2-pin terminal block “DC” out port
Data Rate 10/100/1000Mbps
LED Indicator
PWR (Green)
DC Ready x 1 (Green)
Input Voltage 44~56V DC
Power Requirement
4-pair 802.3at PoE+ and 802.3bt PoE++:
52~56V DC
802.3at PoE+: 48~56V DC
Power Consumption
Ethernet full loading without DC output:
Full loading with maximum 12V DC, 5A
output: 70watts
ESD Protection
Air 8KV DC
Contact 6KV DC
Surge Protection 6KV
Enclosure IP67-rated and IK10 aluminum case
Installation Wall-mount ear
Standards Conformance
Regulatory Compliance FCC Part 15 Class A, CE
Stability Testing
IEC 60068-2-32 (Free fall)
IEC 60068-2-27 (Shock)
IEC 60068-2-6 (Vibration)
Standards Conformances
IEEE 802.3 10BASE-T Ethernet
IEEE 802.3u 100BASE-TX Fast Ethernet
IEEE 802.3ab 1000BASE-T Gigabit
Ethernet
IEEE 802.3af Power over Ethernet
IEEE 802.3at Power over Ethernet Plus
IEEE 802.3bt Power over Ethernet Plus
Plus
Environment
Operating Temperature -40 ~ 75 degrees C
Storage Temperature -40 ~ 85 degrees C
Humidity 5 ~ 95% (non-condensing)
Note
The PoE power output ability will depend on the distance.
5. Customer Support
Thank you for purchasing PLANET products. You can browse our online
FAQ resource and user’s manual on PLANET web site rst to check if it
could solve your issue. If you need more support information, please
contact PLANET support team.
PLANET online FAQs:
https://www.planet.com.tw/en/support/faq
Support team mail address:
[e-mail]
Copyright © PLANET Technology Corp. 2022.
Contents are subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp.
All other trademarks belong to their respective owners.
Note
EMD (Lightning) DAMAGE IS NOT CONVERED UNDER
WARRANTY.
3.5 Connecting IPOE-175S to PSE
Power
DC12V
DC
DC
Power Line (DC)
1000BASE-T UTP
PoE
1000BASE-T UTP with PoE
IPOE-175S
802.3bt PoE
++
PSE
PoE
Power
Data
Data
100m
802.3bt PoE
++
10/100/1000BASE-T
Non-PoE Device
Step 1: Connect attached “Power cable with 2-pin terminal block”
to the “DC Out” port of IPOE-175S Splitter.
Step 2: Connect the other end of DC power wires to remote device.
Tighten the wire-clamp screws for preventing the wires from
loosening.
Step 3: Connect the Cat5e/6 cable to “PoE In” port from an 802.3bt
PoE++ switch/injector to the IPOE-175S Splitter.
Step 4: Connect the Cat5e/6 cable from “Data” port of the IPOE-175S
to remote device.
Step 5: Power on the 802.3bt PoE++ switch/injector.
Step 6: Once the “DC Ready” LED indicator is steadily lit steadily, it
shows it is providing 12V DC power.
Dimensions (W x D x H)
150 x 43.8 x 72.94 mm
169.85 x 43.8 x 72.94 mm, with cable
gland
Weight 424g
MTBF >100,000 hours
Network Cable
10BASE-T: UTP category 3, 5 cable
(≤100m)
100BASE-TX: UTP category 5, 5e cable
(≤100m)
1000BASE-T: UTP category 5e, 6 cable
(≤100m)
Power over Ethernet
PoE Standard
IEEE 802.3bt PoE++ type 3 PD
Backward compatible with IEEE 802.3at
PoE+
PoE Power Supply Type
802.3bt PoE++/PoH (Power over HDBaseT)
802.3at PoE+ End-span/Mid-span
PoE Power Output DC 12V, 5A (60W, full load)
Power Pin Assignment
1/2 (-); 3/6 (+), 4/5 (+), 7/8 (-) or
1/2 (+); 3/6 (-), 4/5 (+), 7/8 (-)