PLANET Fiber Transceiver MFB-Series/MGB-Series/MTB-Series User’s Manual
Trademarks Copyright © PLANET Technology Corp. 2016 Contents are subject to revision without prior notice. PLANET is a registered trademark of PLANET Technology Corp. All other trademarks belong to their respective owners. Disclaimer PLANET Technology does not warrant that the hardware will work properly in all environments and applications, and makes no warranty and representation, either implied or expressed, with respect to the quality, performance, merchantability, or fitness for a particular purpose.
information in this User’s Manual, and reserves the right to make improvements to this User’s Manual and/or to the products described in this User’s Manual, at any time without notice. If you find information in this manual that is incorrect, misleading, or incomplete, we would appreciate your comments and suggestions. FCC Warning This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.
CE Mark Warning This is a Class A product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. WEEE Warning To avoid the potential effects on the environment and human health as a result of the presence of hazardous substances in electrical and electronic equipment, end users of electrical and electronic equipment should understand the meaning of the crossed-out wheeled bin symbol.
Table of Contents 1. Overview.....................................................................................................................................................6 2. Checklist......................................................................................................................................................7 3. Introduction and Model List........................................................................................................................
1. Overview Thank you for purchasing PLANET SFP/SFP+/XFP Mini-GBIC Transceiver which includes the Ethernet module of the MFB/MGB and MTB families. The MFB family’s Fast Ethernet SFP module can be installed into PLANET Switch products with 100BASE-FX SFP interface. The distance can be extended from 2km (Multi-mode, LC) to up to 120km (Single-mode, LC). The MGB family’s Gigabit Ethernet SFP module can be installed into PLANET Switch products with 1000BASE-SX/LX SFP interface.
2. Checklist Your SFP/SFP+/XFP Package should contain the following items: zz The SFP/SFP+/XFP Transceiver Module x 1 zz The User’s Manual x 1 If any item is missing or damaged, please consult the dealer from whom you purchased your SFP/ SFP+/XFP Mini-GBIC Ethernet transceiver module.
3. Introduction and Model List 3-1 The MFB-Series Mini-GBIC Transceiver Module List Fast Ethernet Transceiver (100BASE-X SFP) Model Speed (Mbps) Connector Interface Fiber Mode Distance Wavelength (nm) Operating Temp.
Fast Ethernet Transceiver (100BASE-BX, Single Fiber Bi-directional SFP) Model Speed (Mbps) Connector Interface Fiber Mode Distance Wavelength (TX) Wavelength (RX) Operating Temp.
1. When shorter-distance single mode fiber cables are used, you might need to insert an in-line optical attenuator in the link to avoid overloading the receiver. Follow the I-TUT G652 document to imitate the fiber cable length. 2. The attenuation coefficient mentioned in the following chapters is for reference only. Attenuation coefficient Wavelength region Typical link value 1260nm-1360nm 0.5 dB/km 1530nm-1565nm 0.
SFP Model MFB-F20 MFB-TF20 MFB-F40 MFB-F60 MFB-F120 10 < n < 20 2 dB 4-6 dB 8-10 dB 25-27 dB 20 < n < 40 -- 2-4 dB 6-8 dB 23-25 dB 40 < n < 60 -- -- 2-4 dB 18-20 dB Physical Fiber Cable Length “n” km SFP Model MFB-TFA10 MFB-TFB10 MFB-FA20 / MFB-FB20 MFB-TFA20 / MFB-TFB20 MFB-TFA40 MFB-TFB40 10 < n < 20 -- 2 dB 4-6 dB 20 < n < 40 -- -- 2-4 dB 40 < n < 60 -- -- -- Physical Fiber Cable Length “n” km - 11 -
3-2 The MGB-Series Mini-GBIC Transceiver Module List Gigabit Ethernet Transceiver (1000BASE-X SFP) Model Speed (Mbps) Connector Interface Fiber Mode Distance Wavelength (nm) Operating Temp.
MGB-L70 1000 LC Single Mode 70km 1550nm 0 ~ 60 ºC MGB-L120 1000 LC Single Mode 120km 1550nm 0 ~ 60 ºC MGB-TSX 1000 LC Multi-Mode 550m 850nm -40 ~ 75 ºC MGB-TLX 1000 LC Single Mode 10km 1310nm -40 ~ 75 ºC MGB-TL30 1000 LC Single Mode 30km 1310nm -40 ~ 75 ºC MGB-TL70 1000 LC Single Mode 70km 1550nm -40 ~ 75 ºC Gigabit Ethernet Transceiver (1000BASE-BX, Single Fiber Bi-directional SFP) Model Speed (Mbps) Connector Interface Fiber Mode Distance Wavelength (TX) Wav
MGB-LB10 1000 WDM (LC) Single Mode 10km 1550nm 1310nm 0 ~ 60 ºC MGB-LA20 1000 WDM (LC) Single Mode 20km 1310nm 1550nm 0 ~ 60 ºC MGB-LB20 1000 WDM (LC) Single Mode 20km 1550nm 1310nm 0 ~ 60 ºC MGB-LA40 1000 WDM (LC) Single Mode 40km 1310nm 1550nm 0 ~ 60 ºC MGB-LB40 1000 WDM (LC) Single Mode 40km 1550nm 1310nm 0 ~ 60 ºC MGB-LA60 1000 WDM (LC) Single Mode 60km 1310nm 1550nm 0 ~ 60 ºC MGB-LB60 1000 WDM (LC) Single Mode 60km 1550nm 1310nm 0 ~ 60 ºC MGB-TLA1
MGB-TLA40 1000 WDM (LC) Single Mode 40km 1310nm 1550nm -40 ~ 75 ºC MGB-TLB40 1000 WDM (LC) Single Mode 40km 1550nm 1310nm -40 ~ 75 ºC MGB-TLA60 1000 WDM (LC) Single Mode 60km 1310nm 1550nm -40 ~ 75 ºC MGB-TLB60 1000 WDM (LC) Single Mode 60km 1550nm 1310nm -40 ~ 75 ºC Physical Fiber Cable Length “n” km SFP Model MGB-LX MGB-L30 MGB-L40 MGB-L70 MGB-L120 10 < n < 20 -- 2-4 dB 5-7 dB 13-15 dB 25-27 dB 20 < n < 40 -- 2 dB 3-5 dB 10-12 dB 23-25 dB 40 < n < 60 --
Physical Fiber Cable Length “n” km SFP Model MGB-TLX MGB-TL30 MGB-TL70 10 < n < 20 -- 2-4 dB 13-15 dB 20 < n < 40 -- 2 dB 10-12 dB 40 < n < 60 -- -- 5-7 dB SFP Model MGB-LA10 MGB-LB10 MGB-TLA10 MGB-TLB10 MGB-LA20 MGB-LB20 MGB-TLA20 MGB-TLB20 MGB-LA40 MGB-LB40 MGB-TLA40 MGB-TLB40 MGB-LA60 MGB-LB60 MGB-TLA60 MGB-TLB60 10 < n < 20 -- 2 dB 4-6 dB 8-10 dB 20 < n < 40 -- -- 2-4 dB 6-8 dB 40 < n < 60 -- -- -- 2-4 dB Physical Fiber Cable Length “n” km - 16 -
3-3 The MTB-Series Mini-GBIC Transceiver Module List 10Gbps XFP (10G Ethernet/10GBASE) Model Speed (Mbps) Connector Interface Fiber Mode Distance Wavelength (nm) Operating Temp. MTB-XSR 10G LC Multi-Mode Up to 300m 850nm 0 ~ 60 ºC MTB-XLR 10G LC Single Mode 10km 1310nm 0 ~ 60 ºC Fiber Mode Distance Wavelength (nm) Operating Temp.
MTB-TSR 10G LC Multi-Mode Up to 300m 850nm -40 ~ 75 ºC MTB-TLR 10G LC Single Mode 10km 1310nm -40 ~ 75 ºC 10Gigabit Ethernet Transceiver (10GBASE-BX, Single Fiber Bi-directional SFP) Speed (Mbps) Connector Interface Fiber Mode Distance Wavelength (TX) Wavelength (RX) Operating Temp.
MTB-LA60 MTB-LB60 10G WDM (LC) Single Mode 60km 1270nm 1330nm 0 ~ 60 ºC 10G WDM (LC) Single Mode 60km 1330nm 1270nm 0 ~ 60 ºC SFP Model MTB-LA20 MTB-LB20 MTB-LA40 MTB-LB40 MTB-LA60 MTB-LB60 10 < n < 20 2 dB 4-6 dB 8-10 dB 20 < n < 40 -- 2-4 dB 6-8 dB 40 < n < 60 -- -- 2-4 dB Physical Fiber Cable Length “n” km - 19 -
4. Installing SFP/SFP+/XFP Transceiver Module 4-1 Install the SFP/SFP+ Mini-GBIC Transceiver Module Please follow these steps to install the SFP/SFP+ Mini-GBIC module: 1. Power on the Switch and place the Switch on a flat surface. Install the new SFP/SFP+ Mini-GBIC module by inserting it into the slot and sliding it in until it stops (See Figure 1). Press it firmly until you hear the module snap into place. Never force, twist or bend the SFP/SFP+ Mini-GBIC module.
4-2 Install the 10GBASE-LR/SR XFP Fiber Optic Module MTB-XSR/MTB-XLR The 10GBASE-LR/SR Fiber Optic module can be installed into Planet products with 10G XFP interface. Please refer to the following steps to install the 10GBASE-LR/SR Fiber Optic module: 1. Install the XGS3-M24GX or XGS3-S4XG module into the XGS3-42000R; its 10G XFP slot supports hot swappable feature. 2. Power on the XGS3-42000R L3 Switch and place the Switch on a flat surface.
4-3 Remove the SFP/SFP+/XFP Transceiver Module 1. 2. 3. 4. Make sure there is no network activity by consulting or checking with the network administrator. Remove the Fiber Optic Cable gently. Turn the handle of the SFP/SFP+/XFP Transceiver module to the horizontal level. Pull out the SFP/SFP+/XFP Transceiver module gently through the handle. XG S3-XFP 1-Po rt 10G Warning XFP Mod ule Never pull out the SFP/SFP+/XFP Transceiver module without pulling the handle or the push bolts on the module.
Appendix A A.1 Fiber Optic Cable Connection Parameters The wiring details are shown below: Fiber Optic Patch Cables: Standard Fiber Type Cable Specifications 100BASE-FX Multi-mode 50/125μm or 62.5/125μm 100BASE-FX Single mode 9/125μm 1000BASE-SX Multi-mode 50/125μm or 62.5/125μm 1000BASE-LX Single mode 9/125μm 1000BASE-BX Single mode 9/125μm 10GBASE-SR Multi-mode 50/125μm or 62.
Safety Notice Fiber-optic SFP modules are equipped with a Class 1 laser, which emits invisible radiation. Read the following safety warning carefully. Note Class 1 Laser Product Complies with FDA Regulation 21 CFR 1040.10 and 1040.11 Class 1 radiation is present when the device or system is powered up. Warning Only trained and qualified personnel should be allowed to install or replace these modules.
