User's Manual

ManualsBrandsPLANET Technology ManualsBroadband CommunicationL3 14-Port 100/1G SFP with 4 shared 10/100/1000T + 10-Port 1G/2.5G SFP + 4-Port 10G SFP+ Metro Ethernet Switch

Table Of Contents

Command Guide

-1-

Summary of content (433 pages)

PAGE 1
Command Guide -1-
PAGE 2
Command Guide Contents Chapter 1 COMMAND LINE INTERFACE ........................................................ 20 1.1 Accessing the CLI ....................................................................................................... 20 1.2 Command Line Modes................................................................................................ 20 1.3 Requirements .............................................................................................................. 21 1.
PAGE 3
Command Guide 4.1.19 clear ip igmp snooping statistics ........................................................................................................................38 4.1.20 clear ip igmp snooping vlan ...............................................................................................................................38 4.1.21 clear ip statistics icmp icmp-msg .......................................................................................................................39 4.1.
PAGE 4
Command Guide 4.2.4 aaa authentication login http local .......................................................................................................................55 4.2.5 aaa authentication login http radius .....................................................................................................................56 4.2.6 aaa authentication login http tacacs ....................................................................................................................56 4.2.
PAGE 5
Command Guide 4.2.45 erps <1-64> rpl neighbor ...................................................................................................................................79 4.2.46 erps <1-64> rpl owner .......................................................................................................................................79 4.2.47 erps <1-64> sub ..............................................................................................................................................
PAGE 6
Command Guide 4.2.65.21 evc l2cp forward(GG) ..........................................................................................................................106 4.2.65.22 evc l2cp peer(GG) ...............................................................................................................................107 4.2.65.23 evc update dei .....................................................................................................................................108 4.2.65.
PAGE 7
Command Guide 4.2.65.62 loop-protect tx-mode ...........................................................................................................................127 4.2.65.63 loop-protect tx-mode ...........................................................................................................................128 4.2.65.64 mac address-table learning .................................................................................................................128 4.2.65.65 media-type........
PAGE 8
Command Guide 4.2.65.103 qos storm unicast ..............................................................................................................................150 4.2.65.104 qos storm unknown ...........................................................................................................................151 4.2.65.105 qos tag-remark ..................................................................................................................................152 4.2.65.
PAGE 9
Command Guide 4.2.66.5 ip address dhcp .....................................................................................................................................174 4.2.66.6 ip address dhcp fallback ........................................................................................................................174 4.2.66.7 ip dhcp server ........................................................................................................................................175 4.2.66.
PAGE 10
Command Guide 4.2.73.11 hardware-address ................................................................................................................................197 4.2.73.12 host .....................................................................................................................................................197 4.2.73.13 lease....................................................................................................................................................198 4.2.
PAGE 11
Command Guide 4.2.96 ipv6 mld host-proxy leave-proxy ......................................................................................................................218 4.2.97 ipv6 mld snooping............................................................................................................................................218 4.2.98 ipv6 mld snooping vlan ....................................................................................................................................219 4.
PAGE 12
Command Guide 4.2.123 mep ais .......................................................................................................................................240 4.2.124 mep aps ......................................................................................................................................241 4.2.125 mep cc ........................................................................................................................................
PAGE 13
Command Guide 4.2.164 network-clock clk-source aneg-mode .......................................................................................266 4.2.165 no ..................................................................................................................................................................267 4.2.166 ntp .................................................................................................................................................................
PAGE 14
Command Guide 4.2.199 rmon alarm ....................................................................................................................................................294 4.2.200 rmon event ....................................................................................................................................................295 4.2.201 sflow agent-ip .....................................................................................................................................
PAGE 15
Command Guide 4.2.219 transport email smtp-server ...........................................................................................................................318 4.2.220 transport email to ...........................................................................................................................................319 4.2.221 upnp ........................................................................................................................................................
PAGE 16
Command Guide 4.11.1 erps ..................................................................................................................................................................334 4.12 exit............................................................................................................................ 335 4.12.1 exit ...................................................................................................................................................................
PAGE 17
Command Guide 4.21.14 show evc .......................................................................................................................................................355 4.21.15 show evc statistics .........................................................................................................................................356 4.21.16 show green-ethernet..................................................................................................................................
PAGE 18
Command Guide 4.21.55 show ipv6 mld snooping mrouter ...................................................................................................................384 4.21.56 show ipv6 neighbor........................................................................................................................................384 4.21.57 show ipv6 route .............................................................................................................................................385 4.21.
PAGE 19
Command Guide 4.21.96 show snmp view ............................................................................................................................................419 4.21.97 show spanning-tree .......................................................................................................................................420 4.21.98 show switchport forbidden .............................................................................................................................421 4.
PAGE 20
Command Guide Chapter 1 COMMAND LINE INTERFACE 1.1 Accessing the CLI When accessing the management interface for the switch over a direct connection to the server’s console port, or via a Telnet connection, the switch can be managed by entering command keywords and parameters at the prompt. Using the switch's command-line interface (CLI) is very similar to entering commands on a UNIX system. This chapter describes how to use the Command Line Interface (CLI). 1.
PAGE 21
Command Guide The CLI provides the following modes:  User Mode When the operator logs into the CLI, the User Mode is the initial mode. The User Mode contains a limited set of commands. The command prompt shown at this level is: Command Prompt: switch>  Privileged Mode To have access to the full suite of commands, the operator must enter the Privileged Mode. The Privileged Mode requires password authentication.
PAGE 22
Command Guide 1.4 Command Support As shown in the following table, some command groups or commands are supported on particular switch models. E.R.P.
PAGE 23
Command Guide IGSW-24040T(v3) - - ■ ■ ■ IGS-5225-16T4S - - ■ ■ ■ ■ - ■ ■ ■ IGS-604HPT-RJ - ■ ■ - ■ IGS-604HPT-M12 - ■ ■ - ■ IGS-5226-4P2T - ■ ■ - ■ IGS-5225-20T4C2X ■ = Supported, - = Not supported -23-
PAGE 24
Command Guide Chapter 2 CONSOLE CLI MANAGEMENT 2.1 Terminal Setup To configure the system, connect a serial cable to a COM port on a PC or notebook computer and to RJ45 type of serial (console) port of the Industrial Managed Switch. Figure 2-1 Industrial Managed Switch Console Connectivity The console port of the Industrial Managed Switch is an RJ45 type, RS-232 serial port connector. It is an interface for connecting a terminal directly.
PAGE 25
Command Guide Figure 2-3 Hyper Terminal COM Port Configuration You can change these settings, if desired, after you log on. This management method is often preferred because you can remain connected and monitor the system during system reboots. Also, certain error messages are sent to the serial port, regardless of the interface through which the associated action was initiated. A Macintosh or PC attachment can use any terminal-emulation program for connecting to the terminal serial port.
PAGE 26
Command Guide 2.2 Logon to the Console Once the terminal is connected to the device, power on the Industrial Managed Switch, and the terminal will display “running testing procedures”. Then, the following message asks to log-in user name and password. The factory default user name and password are shown as follows and the login screen in Figure 3-1 appears.
PAGE 27
Command Guide To check the current IP address or modify a new IP address for the Switch, please use the procedures as follows:  Show the current IP Address 1. At the “#” prompt, enter “show ip interface brief”. 2. The screen displays the current IP address and subnet mask as shown in Figure 3-2. Figure 3-2: IP Information Screen  Configuring IP Address 3. At the “#” prompt, enter the following command and press as shown in Figure 3-3.
PAGE 28
Command Guide Figure 3-3: Configuring IP Address Screen 4.  Repeat step 1 to check if the IP address has changed. Storing current switch configuration 5. At the “#” prompt, enter the following command and press . # copy running-config startup-config Figure 3-4: Saving Current Configuration Command Screen If the IP is successfully configured, the Industrial Managed Switch will apply the new IP address setting immediately.
PAGE 29
Command Guide Chapter 3 TELNET CLI MANAGEMENT 3.1 Telnet Login The Industrial Managed Switch also supports telnet for remote management. The switch asks for user name and password for remote login when using telnet; please use “admin” for both username and password. Default IP address: 192.168.0.
PAGE 30
Command Guide Chapter 4 Commands for CLI Configuration 4.1 clear 4.1.1 clear access management statistics Command: clear access management statistics Default: N/A Usage Guide: To clear the access management statistics. Example: To clear the Switch’s access management statistics. Switch# clear access management statistics 4.1.2 clear access-list ace statistics Command: clear access-list ace statistics Default: N/A Usage Guide: To clear the Access list entry statistics.
PAGE 31
Command Guide 4.1.3 clear dot1x statistics interface Command: clear dot1x statistics interface GigabitEthernet | 10GigabitEthernet Default: N/A Usage Guide: To clear the dot1x statistics. Example: To clear the Switch’s GigabitEthernet 1/25 dot1x statistics. Switch# clear dot1x statistics interface GigabitEthernet 1/25 4.1.4 clear eps Command: clear eps The EPS instance number. Default: N/A Usage Guide: To clear the EPS instance number. 4.1.
PAGE 32
Command Guide Example: To clear the Switch’s ERPS group 1 statistics. Switch# # clear erps 1 statistics 4.1.6 clear erps statistics Command: clear erps statistics Default: N/A Usage Guide: To clear the ERPS statistics. Example: To clear the Switch’s ERPS statistics. Switch# clear erps statistics 4.1.7 clear evc statistics Command: clear evc statistics Default: N/A Usage Guide: To clear the Ethernet Virtual Connections statistics. Example: To clear the Switch’s Ethernet Virtual Connections statistics.
PAGE 33
Command Guide 4.1.8 clear ip arp Command: clear ip arp Default: N/A Usage Guide: To clear the ARP cache. Example: To clear the Switch’s ARP cache. Switch# clear ip arp 4.1.9 clear ip dhcp detailed statistics all Command: clear ip dhcp detailed statistics all Default: N/A Usage Guide: To clear the DHCP detailed statistics for all. Example: To clear the Switch’s DHCP detailed statistics for all.
PAGE 34
Command Guide 4.1.10 clear ip dhcp detailed statistics client Command: clear ip dhcp detailed statistics client Default: N/A Usage Guide: To clear the DHCP client statistics. Example: To clear the Switch’s DHCP client statistics. Switch# clear ip dhcp detailed statistics client 4.1.11 clear ip dhcp detailed statistics helper Command: clear ip dhcp detailed statistics helper Default: N/A Usage Guide: To clear the DHCP normal L2 or L3 forward statistics.
PAGE 35
Command Guide 4.1.12 clear ip dhcp detailed statistics server Command: clear ip dhcp detailed statistics server Default: N/A Usage Guide: To clear the DHCP server statistics. Example: To clear the Switch’s DHCP server statistics. Switch# clear ip dhcp detailed statistics server 4.1.13 clear ip dhcp detailed statistics snooping Command: clear ip dhcp detailed statistics snooping Default: N/A Usage Guide: To clear the DHCP snooping statistics.
PAGE 36
Command Guide 4.1.14 clear ip dhcp relay statistics Command: clear ip dhcp relay statistics Default: N/A Usage Guide: To clear the DHCP relay statistics. Example: To clear the Switch’s DHCP relay statistics. Switch# clear ip dhcp relay statistics 4.1.15 clear ip dhcp server binding Command: clear ip dhcp server binding A.B.C.D Default: N/A Usage Guide: To clear the DHCP server binding cache. Example: To clear the Switch’s DHCP server(192.168.0.100) binding cache.
PAGE 37
Command Guide Usage Guide: To clear the DHCP automatic bindings cache. Example: To clear the Switch’s DHCP automatic bindings cache. Switch# clear ip dhcp server binding automatic 4.1.17 clear ip dhcp server binding expired Command: clear ip dhcp server binding expired Default: N/A Usage Guide: To clear the DHCP expired bindings for free. Example: To clear the Switch’s DHCP expired bindings for free. Switch# clear ip dhcp server binding expired 4.1.
PAGE 38
Command Guide 4.1.19 clear ip igmp snooping statistics Command: clear ip igmp snooping statistics Default: N/A Usage Guide: To clear the IGMP snooping statistics. Example: To clear the Switch’s IGMP snooping statistics. Switch# clear ip igmp snooping statistics 4.1.20 clear ip igmp snooping vlan Command: clear ip igmp snooping vlan < vlan_list> statistics VLAN identifier(s): VID Default: N/A Usage Guide: To clear the IGMP snooping vlan < vlan_list> statistics.
PAGE 39
Command Guide 4.1.21 clear ip statistics icmp icmp-msg Command: clear ip statistics icmp icmp-msg ICMP message type ranges from 0 to 255 Default: N/A Usage Guide: To clear the IPv4 ICMP traffic for designated message type. Example: To clear the Switch’s IPv4 ICMP traffic for designated message type 0. Switch# clear ip statistics icmp icmp-msg 0 4.1.
PAGE 40
Command Guide 4.1.23 clear ip statistics system icmp icmp-msg Command: clear ip statistics system icmp icmp-msg ICMP message type ranges from 0 to 255 Default: N/A Usage Guide: To clear the IPv4 ICMP statistics for specific ICMP message type. Example: To clear the Switch’s IPv4 ICMP statistics for specific ICMP message type 0. Switch# clear ip statistics system icmp icmp-msg 0 4.1.
PAGE 41
Command Guide 4.1.25 clear ipv6 mld snooping statistics Command: clear ipv6 mld snooping statistics Default: N/A Usage Guide: To clear the ipv6 mld snooping statistics. Example: To clear the Switch’s ipv6 mld snooping statistics. Switch# clear ipv6 mld snooping statistics 4.1.26 clear ipv6 mld snooping vlan Command: clear ipv6 mld snooping vlan statistics VLAN identifier(s): VID Default: N/A Usage Guide: To clear the ipv6 mld snooping statistics for specific VLAN.
PAGE 42
Command Guide 4.1.27 clear ipv6 neighbors Command: clear ipv6 neighbors Default: N/A Usage Guide: To clear the ipv6 neighbors. Example: To clear the Switch’s ipv6 neighbors. Switch# clear ipv6 neighbors 4.1.28 clear ipv6 statistics icmp icmp-msg Command: clear ipv6 statistics icmp icmp-msg ICMP message type ranges from 0 to 255 Default: N/A Usage Guide: To clear the IPv6 ICMP traffic for designated message type.
PAGE 43
Command Guide 4.1.29 clear ipv6 statistics icmp interface vlan Command: clear ipv6 statistics icmp interface vlan VLAN identifier(s): VID Default: N/A Usage Guide: To clear the IPv6 interface/ICMP statistics for specific VLAN. Example: To clear the Switch’s IPv6 interface/ICMP statistics for specific VLAN 1. Switch# clear ipv6 statistics icmp interface vlan 1 4.1.
PAGE 44
Command Guide 4.1.31 clear ipv6 statistics system icmp interface vlan Command: clear ipv6 statistics system icmp interface vlan VLAN identifier(s): VID Default: N/A Usage Guide: To clear the IPv6 ICMP interface statistics for specific VLAN. Example: To clear the Switch’s IPv6 ICMP interface statistics for specific VLAN 1. Switch# clear ipv6 statistics system icmp interface vlan 1 4.1.
PAGE 45
Command Guide 4.1.33 clear lldp statistics Command: clear lldp statistics Default: N/A Usage Guide: To clear the lldp statistics. Example: To clear the Switch’s lldp statistics. Switch# clear lldp statistics 4.1.34 clear logging error info Command: clear logging error info Default: N/A Usage Guide: To clear the logging error info. Example: To clear the Switch’s logging error info. Switch# clear logging error info 4.1.
PAGE 46
Command Guide Usage Guide: To clear the logging error warning. Example: To clear the Switch’s logging error warning. Switch# clear logging error warning 4.1.36 clear logging info error Command: clear logging info error Default: N/A Usage Guide: To clear the logging info error. Example: To clear the Switch’s logging info error. Switch# clear logging info error 4.1.37 clear logging info warning Command: clear logging info warning Default: N/A Usage Guide: To clear the logging info warning.
PAGE 47
Command Guide 4.1.38 clear logging warning error Command: clear logging warning error Default: N/A Usage Guide: To clear the logging warning error. Example: To clear the Switch’s logging warning error. Switch# clear logging warning error 4.1.39 clear logging warning info Command: clear logging warning info Default: N/A Usage Guide: To clear the logging warning info. Example: To clear the Switch’s logging warning info. Switch# clear logging warning info 4.1.
PAGE 48
Command Guide Usage Guide: To clear the mac address-table. Example: To clear the Switch’s mac address-table. Switch# clear mac address-table 4.1.41 clear mep Command: clear mep The MEP instance. Default: N/A Usage Guide: To clear the MEP instance profiles. 4.1.42 clear mvr name Command: clear mvr name MVR multicast VLAN name Default: N/A Usage Guide: To clear the mvr name profiles.
PAGE 49
Command Guide 4.1.43 clear mvr statistics Command: clear mvr statistics Default: N/A Usage Guide: To clear the mvr statistics. Example: To clear the Switch’s mvr statistics. Switch# clear mvr statistics 4.1.44 clear mvr vlan Command: clear mvr vlan statistics MVR multicast VLAN list Default: N/A Usage Guide: To clear the mvr vlan statistics for specific VLAN. Example: To clear the Switch’s mvr vlan statistics for specific VLAN 1. Switch# clear mvr vlan 1 statistics 4.1.
PAGE 50
Command Guide Usage Guide: To clear the ERPS WTR timer for a specific profile. Example: To clear the Switch’s ERPS WTR timer for a specific profile 1. Switch# clear network-clock clk-source 1 4.1.46 clear spanning-tree detected-protocols interface * Command: clear spanning-tree detected-protocols interface * Default: N/A Usage Guide: To clear the spanning-tree detected-protocols for all. Example: To clear the Switch’s spanning-tree detected-protocols for all.
PAGE 51
Command Guide 4.1.48 clear spanning-tree detected-protocols interface GigabitEthernet Command: clear spanning-tree detected-protocols interface GigabitEthernet Port list in X/X-XX Default: N/A Usage Guide: To clear the spanning-tree detected-protocols for specific GigabitEthernet port. Example: To clear the Switch’s spanning-tree detected-protocols for specific GigabitEthernet 1/1. Switch# clear spanning-tree detected-protocols interface GigabitEthernet 1/1 4.1.
PAGE 52
Command Guide 4.1.50 clear spanning-tree statistics interface * Command: clear spanning-tree statistics interface * Default: N/A Usage Guide: To clear the spanning-tree statistics for all. Example: To clear the Switch’s spanning-tree statistics for all. Switch# clear spanning-tree statistics interface * 4.1.
PAGE 53
Command Guide Usage Guide: To clear the spanning-tree statistics for specific 10GigabitEthernet port. Example: To clear the Switch’s spanning-tree statistics for specific 10GigabitEthernet 1/1. Switch# clear spanning-tree statistics interface 10GigabitEthernet 1/1 4.1.53 clear statistics * Command: clear statistics * Default: N/A Usage Guide: To clear the statistics for all. Example: To clear the Switch’s statistics for all. Switch# clear statistics * 4.1.
PAGE 54
Command Guide 4.1.55 clear statistics 10GigabitEthernet Command: clear statistics 10GigabitEthernet Port list in X/X-XX Default: N/A Usage Guide: To clear the statistics for specific 10GigabitEthernet port. Example: To clear the Switch’s statistics for specific 10GigabitEthernet 1/1. Switch# clear statistics 10GigabitEthernet 1/1 4.2 configure terminal 4.2.
PAGE 55
Command Guide 4.2.2 aaa authentication login console radius Command: aaa authentication login console radius Default: console : local Usage Guide: To authenticate the radius account via console only. Example: To authenticate the local and radius account via console. Switch# configure terminal Switch (config)# aaa authentication login console local radius 4.2.
PAGE 56
Command Guide Usage Guide: To authenticate the local account via http only. Example: To authenticate the local account via http. Switch# configure terminal Switch (config)# aaa authentication login http local 4.2.5 aaa authentication login http radius Command: aaa authentication login http radius Default: http : local Usage Guide: To authenticate the radius account via http only. Example: To authenticate the local and radius account via http.
PAGE 57
Command Guide Switch# configure terminal Switch (config)# aaa authentication login http local radius tacacs 4.2.7 aaa authentication login ssh local Command: aaa authentication login ssh local Default: ssh : local Usage Guide: To authenticate the local account via ssh only. Example: To authenticate the local account via ssh. Switch# configure terminal Switch (config)# aaa authentication login ssh local 4.2.
PAGE 58
Command Guide 4.2.9 aaa authentication login ssh tacacs Command: aaa authentication login ssh tacacs Default: ssh : local Usage Guide: To authenticate the tacacs account via ssh only. Example: To authenticate the local and radius and tacacs account via console. Switch# configure terminal Switch (config)# aaa authentication login ssh local radius tacacs 4.2.
PAGE 59
Command Guide 4.2.11 aaa authentication login telnet radius Command: aaa authentication login telnet radius Default: telnet : local Usage Guide: To authenticate the radius account via telnet only. Example: To authenticate the local and radius account via telnet. Switch# configure terminal Switch (config)# aaa authentication login telnet local radius 4.2.
PAGE 60
Command Guide 4.2.
PAGE 61
Command Guide action Access list action dmac-type The type of destination MAC address frametype Frame type ingress Ingress logging Logging frame information. Note: The logging feature only works when the packet length is less than 1518 (without VLAN tags) and the System Log memory size and logging rate are limited. next Insert the current ACE before the next ACE ID policy Policy rate-limiter Rate limiter redirect Redirect frame to specific port shutdown Shutdown incoming port.
PAGE 62
Command Guide interface 10GigabitEthernet | GigabitEthernet } | tag-priority {0-1, 0-3, 2-3, 4-5, 4-7, 6-7, , any} | vid {, any} ACE ID action Access list action dmac-type The type of destination MAC address frametype Frame type ingress Ingress logging Logging frame information. Note: The logging feature only works when the packet length is less than 1518 (without VLAN tags) and the System Log memory size and logging rate are limited.
PAGE 63
Command Guide 4.2.16 access-list rate-limiter Command: access-list rate-limiter pps Rate limiter ID Rate value Default: 0 Usage Guide: To set pps rate for specific rate-limiter ID. Example: To set pps rate(10000 pps) for specific rate-limiter ID 1. Switch# configure terminal Switch (config)# access-list rate-limiter 1 pps 10000 4.2.
PAGE 64
Command Guide 4.2.18 aggregation mode Command: aggregation mode dmac | ip | port | smac dmac Destination MAC affects the distribution ip IP address affects the distribution port IP port affects the distribution smac Source MAC affects the distribution Default: SMAC : Enabled DMAC : Disabled IP : Enabled Port : Enabled Usage Guide: To configure static aggregation mode type.
PAGE 65
Command Guide Usage Guide: To configure static aggregation mode type. Example: To configure static aggregation mode type with Destination MAC affects the distribution and Source MAC affects the distribution only. Switch# configure terminal Switch (config)# access-list rate-limiter pps 100 4.2.20 banner Command: banner c banner-text c, where 'c' is a delimiting character Default: N/A Usage Guide: To configure banner-text. Example: To configure banner-text with word “ddddd”.
PAGE 66
Command Guide 4.2.21 banner exec Command: banner login c banner-text c, where 'c' is a delimiting character Default: N/A Usage Guide: To configure login banner-text. Example: To configure login banner-text with word “wwwwwwwwww”. Switch# configure terminal Switch (config)# banner exec 1 Enter TEXT message. End with the character '1'. gggggg 1 Telnet 192.168.0.100: Username: admin Password: gggggg # 4.2.
PAGE 67
Command Guide Example: To configure login banner-text with word “wwwwwwwwww”. Switch# configure terminal Switch (config)# banner login 1 Enter TEXT message. End with the character '1'. wwwwwwwwww 1 Console: Press ENTER to get started wwwwwwwwww Username: admin Password: 4.2.23 banner motd Command: banner motd c banner-text c, where 'c' is a delimiting character Default: N/A Usage Guide: To configure motd banner-text. Example: To configure motd banner-text with word “ffffff”.
PAGE 68
Command Guide Console: ffffff Press ENTER to get started Username: 4.2.24 clock summer-time Command: clock summer-time date Default: N/A Usage Guide: To set daylight saving. Example: To set daylight saving (Started time: Feb, 3. 2013 8:8AM, End time: Dec, 31. 2013 8:8AM, Offset time: 60 minutes).
PAGE 69
Command Guide Example: To set time zone (GMT -15) with profile 1. Switch# configure terminal Switch (config)# clock timezone 1 -15 4.2.26 default access-list rate-limiter Command: default access-list rate-limiter Rate limiter ID Default: 0 Usage Guide: To default the Rate limiter. Example: To default the Rate limiter ID 1. Switch# configure terminal Switch (config)# default access-list rate-limiter 1 4.2.
PAGE 70
Command Guide 4.2.28 dot1x authentication timer re-authenticate Command: dot1x authentication timer re-authenticate <1-3600> Default: Re-authenticated Period: 3600 Usage Guide: To set the Re-authenticated Period for Network Access Server. Example: To set the Re-authenticated Period (777 seconds). Switch# configure terminal Switch (config)# dot1x authentication timer re-authenticate 777 4.2.
PAGE 71
Command Guide <1-4095> Guest VLAN ID used when entering the Guest VLAN. Default: 1 Usage Guide: To set the value of guest-vlan for Network Access Server Example: To set the value of guest-vlan(2) for Network Access Server Switch# configure terminal Switch (config)# dot1x guest-vlan 2 4.2.31 dot1x guest-vlan supplicant Command: dot1x guest-vlan supplicant supplicant The switch remembers if an EAPOL frame has been received on the port for the life-time of the port.
PAGE 72
Command Guide Default: 2 Usage Guide: To define 802.1X re-authentication frequency for Network Access Server Example: To define 802.1X re-authentication frequency with 78 times for Network Access Server Switch# configure terminal Switch (config)# dot1x max-reauth-req 78 4.2.33 dot1x system-auth-control Command: dot1x system-auth-control Default: Disable Usage Guide: To enable 802.1X service for Network Access Server Example: To enable 802.
PAGE 73
Command Guide Switch# configure terminal Switch (config)# dot1x timeout quiet-period 12 4.2.35 dot1x timeout tx-period Command: dot1x timeout tx-period <1-65535> tx-period The time between EAPOL retransmissions. Default: 30 Usage Guide: To configure 802.1X EPOAL timeout for Network Access Server Example: To configure 802.1X EPOAL timeout (45 seconds) for Network Access Server Switch# configure terminal Switch (config)# dot1x timeout tx-period 45 4.2.
PAGE 74
Command Guide Switch# configure terminal Switch (config)# enable password admin Press ENTER to get started Username: Password: > enable Password: ***** # 4.2.37 enable password level Command: enable password level <1-15> <1-15> Level number The UNENCRYPTED (cleartext) password.
PAGE 75
Command Guide 4.2.38 enable secret Command: enable secret 0 | 5 level <1-15> 0 Specifies an UNENCRYPTED password will follow 5 Specifies an ENCRYPTED secret will follow <1-15> Level number The UNENCRYPTED (cleartext) / ENCRYPTED(MD5) password.
PAGE 76
Command Guide 4.2.39 end Command: end Default: N/A Usage Guide: To level the configure terminal mode Example: To level the configure terminal mode Switch# configure terminal Switch (config)# end # 4.2.40 erps <1-64> guard Command: erps <1-64> guard <10-2000> <1-64> ERPS group number <10-2000> Guard time in ms Default: 500 Usage Guide: To configure the Guard Time for ERPS.
PAGE 77
Command Guide 4.2.41 erps <1-64> holdoff Command: erps <1-64> holdoff < 0-10000> <1-64> ERPS group number < 0-10000> Holdoff time in ms Default: 0 Usage Guide: To configure the Hold Off Time for ERPS Example: To configure the Hold Off Time (178 ms) for ERPS(Profile 1) Switch# configure terminal Switch (config)# erps 1 holdoff 900 4.2.
PAGE 78
Command Guide 4.2.43 erps <1-64> mep Command: erps <1-64> mep port0 sf aps port1 sf aps <1-64> ERPS group number Index of Port 0 SignalFail MEP Index of Port 0 APS MEP Index of Port 1 SignalFail MEP Index of Port 1 APS MEP Default: 0 Usage Guide: To configure ERPS Instance Data for specific ERPS profile. Example: To configure ERPS Instance Data(Port0: SF MEP = 2, APS MEP = 1.
PAGE 79
Command Guide 4.2.45 erps <1-64> rpl neighbor Command: erps <1-64> rpl neighbor { port0 | port1 } port0 ERPS Port 0 interface port1 ERPS Port 1 interface Default: N/A Usage Guide: To configure Ring Protection Link Neighbor Role for specific ERPS interface. Example: To configure Ring Protection Link Neighbor Role for specific ERPS interface.. Switch# configure terminal Switch (config)# erps 1 rpl neighbor port0 4.2.
PAGE 80
Command Guide 4.2.
PAGE 81
Command Guide Default: N/A Usage Guide: To configure topology change notification (TCN) propagation for the specific profile. Example: To configure topology change notification (TCN) propagation for the specific profile 1 Switch# configure terminal Switch (config)# erps 1 topology-change propagate 4.2.49 erps <1-64> topology-change propagate Command: erps <1-64> version 1 | 2 <1-64> ERPS group number version Version Default: V2 Usage Guide: To configure ERPS version number for the specific profile.
PAGE 82
Command Guide Default: V2 Usage Guide: To configure ERPS VLANs for the specific profile. Example: To configure ERPS VLANs(VLAN5 - VLAN8) for the specific profile 1. Switch# configure terminal Switch (config)# erps 1 vlan add 5-8 4.2.
PAGE 83
Command Guide Switch# configure terminal Switch (config)# evc 1 vid 2 interface GigabitEthernet 1/1-2 ivid 3 learning disable policer 4 4.2.
PAGE 84
Command Guide Added tag PCP preserve Setup tag PCP/DEI preservation type Setup added tag type c-tag Add C-tag none No tag added s-custom-tag Add custom S-tag s-tag Add S-tag vid Setup added tag VLAN ID match Added tag VLAN ID Setup inner tag match properties dei Setup matched DEI Matched DEI any Match any DEI pcp Setup matched PCP Matched PCP value/range any type Match any PCP Setup matched tag type any Matc
PAGE 85
Command Guide preserve Setup tag PCP/DEI preservation vid Setup added tag VLAN ID match Added tag VLAN ID Setup outer tag match properties policer Policer (ingress bandwidth profile) Policer ID discard Map to policer discarding all frames evc Use policer setup for EVC none Map to policer allowing all frames policy Setup ACL policy pop ACL policy Setup tag popping Number of tags popped Default: N/A Usage Guide: To
PAGE 86
Command Guide Switch# configure terminal Switch (config)# evc ece 1 direction both evc 2 frame-type ipv4 inner-tag add dei 1 pcp 4 preserve type s-custom-tag vid 5 interface GigabitEthernet 1/3 outer-tag add dei 0 mode enable pcp 2 vid 7 match dei any pcp any type c-tagged vid 6 policer 8 policy 9 pop 2 4.2.
PAGE 87
Command Guide dei Setup added tag DEI pcp Added tag DEI Setup added tag PCP Added tag PCP preserve Setup tag PCP/DEI preservation type Setup added tag type c-tag Add C-tag none No tag added s-custom-tag Add custom S-tag s-tag Add S-tag vid Setup added tag VLAN ID match Added tag VLAN ID Setup inner tag match properties dei Setup matched DEI Matched DEI any Match any DEI pcp Setup matched PCP
PAGE 88
Command Guide disable No tag added when forwarding to UNI enable Add tag when forwarding to UNI pcp Setup added tag PCP Added tag PCP preserve Setup tag PCP/DEI preservation vid Setup added tag VLAN ID match Added tag VLAN ID Setup outer tag match properties policer Policer (ingress bandwidth profile) Policer ID discard Map to policer discarding all frames evc Use policer setup for EVC none Map to policer allowing all frames pol
PAGE 89
Command Guide cir Setup CIR Committed Information Rate [kbps] disable Disable policer ebs Setup EBS for MEF policer eir Setup EIR for MEF policer enable Setup policer mode aware Color-aware mode blind Color-blind mode coupled Coupling mode rate-type line Excess Information Rate [kbps] Enable policer mode data Excess Burst Size [bytes] Setup rate type Data rate policing Line rate policing type Setup policer type mef MEF ingr
PAGE 90
Command Guide cbs Setup CBS cir Committed Burst Size [bytes] Setup CIR Committed Information Rate [kbps] disable Disable policer ebs Setup EBS for MEF policer eir Setup EIR for MEF policer enable Setup policer mode aware Color-aware mode blind Color-blind mode coupled Coupling mode rate-type line Excess Information Rate [kbps] Enable policer mode data Excess Burst Size [bytes] Setup rate type Data rate polic
PAGE 91
Command Guide ivid EVC VLAN ID Setup internal EVC VLAN ID Internal VLAN ID interface Setup NNI learning Setup learning policer Policer (ingress bandwidth profile) discard none Policer ID List of VLANs Map to policer discarding all frames Map to policer allowing all frames Default: 0 Usage Guide: To update an ID for Ethernet Virtual Circuits (EVC).
PAGE 92
Command Guide 4.2.58 green-ethernet led interval Command: green-ethernet led interval <0~24> intensity <0-100> <0~24> Interval from 00.00 to 24.00 (00 is used to start at midnight, while 24 is used to stop at midnight). intensity <0-100> LEDs intensity. Intensity from 0% (LEDs OFF) to 100% Default: N/A Usage Guide: To configure LED Power reduction for interval time. Example: To configure LED Power reduction as tabled below.
PAGE 93
Command Guide Switch# configure terminal Switch (config)# green-ethernet led on-event error link-change 55 4.2.60 gvrp Command: gvrp Default: Disable Usage Guide: To enable GVRP. Example: To enable GVRP. Switch# configure terminal Switch (config)# gvrp 4.2.61 gvrp max-vlans Command: gvrp max-vlans <1-4095> Default: 20 Usage Guide: To configure how many VLANs will be in GVRP. Example: To configure 200 VLANs in GVRP.
PAGE 94
Command Guide 4.2.62 gvrp time Command: gvrp time join-time leave-all-time leave-time join-time Set GARP protocol parameter JoinTime. See IEEE 802.1D-2004, clause 12.11 leave-all-time join-time in units of centi seconds. Range is 1-20. Default is 20. Set GARP protocol parameter LeaveAllTime. See IEEE 802.1D-2004, clause 12.
PAGE 95
Command Guide Usage Guide: To explain how to use commands. Example: To explain how to use commands. Switch# configure terminal Switch (config)# help Help may be requested at any point in a command by entering a question mark '?'. If nothing matches, the help list will be empty and you must back up until entering a '?' showing the available options. Two styles of help are provided: 1. Full help is available when you are ready to enter a command argument (e.g.
PAGE 96
Command Guide 4.2.65 interface * | 10GigabitEthernet | GigabitEthernet Command: interface * | 10GigabitEthernet | GigabitEthernet * All switches or All ports GigabitEthernet 1 Gigabit Ethernet Port 10GigabitEthernet 10 Gigabit Ethernet Port Default: N/A Usage Guide: To enter the interface mode. Example: To enter the interface 10GigabitEthernet 1/2 Switch# configure terminal Switch (config)# interface 10GigabitEthernet 1/2 Switch (config-if) # 4.2.65.
PAGE 97
Command Guide 4.2.65.2 access-list action deny Command: access-list action deny action Access list action Default: Deny Usage Guide: To configure Deny for the ACL action. Example: To configure Deny ACL action for the GigabitEthernet X/X. Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # access-list action deny 4.2.65.3 access-list logging Command: access-list logging logging Logging frame information.
PAGE 98
Command Guide 4.2.65.4 access-list policy Command: access-list policy policy Policy Policy ID Default: Policy ID: 0 Usage Guide: To configure Policy ID for the ACL. Example: To configure ACL Policy ID 1 for the GigabitEthernet X/X. Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # access-list policy 1 4.2.65.
PAGE 99
Command Guide 4.2.65.6 access-list rate-limiter Command: access-list rate-limiter rate-limiter Rate limiter Rate limiter ID Default: Disable Usage Guide: To apply Rate Limiter ID for the ACL. Example: To apply ACL Rate Limiter ID 1 for the GigabitEthernet X/X. Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # access-list rate-limiter 1 4.2.65.
PAGE 100
Command Guide 4.2.65.8 access-list shutdown Command: access-list shutdown shutdown Shut down incoming port. The shutdown feature only works when the packet length is less than 1518 (without VLAN tags). Default: Disable Usage Guide: To enable Shutdown function for the ACL. Example: To enable ACL Shutdown function for the GigabitEthernet X/X. Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # access-list shutdown 4.2.65.
PAGE 101
Command Guide 4.2.65.10 description Command: description description Port description specifies a comment or a description of the port to assist the user. (Length: 1-12 characters) Default: N/A Usage Guide: To configure port description. Example: To configure port description (IPTV_Port) for the GigabitEthernet X/X. Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # description IPTV_Port 4.2.65.
PAGE 102
Command Guide 4.2.65.12 dot1x guest-vlan Command: dot1x guest-vlan dot1x IEEE Standard for port-based Network Access Control guest-vlan Enables/disables guest VLAN Default: Disable Usage Guide: To enable Guest VLAN Example: To enable Guest VLAN for GigabitEthernet X/X. Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # dot1x guest-vlan 4.2.65.
PAGE 103
Command Guide Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # dot1x port-control auto 4.2.65.14 dot1x radius-qos Command: dot1x radius-qos dot1x IEEE Standard for port-based Network Access Control radius-qos Enables/disables per-port state of RADIUS-assigned QoS. Default: Disable Usage Guide: To enable RADIUS-assigned QoS for 802.1X Example: To enable RADIUS-assigned QoS for GigabitEthernet X/X.
PAGE 104
Command Guide Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # dot1x radius-vlan 4.2.65.16 dot1x re-authenticate Command: dot1x re-authenticate dot1x IEEE Standard for port-based Network Access Control re-authenticate Refresh (restart) 802.1X authentication process. Default: N/A Usage Guide: To restart 802.1X authentication process. Example: To restart 802.1X authentication process for GigabitEthernet X/X.
PAGE 105
Command Guide Example: To configure auto duplex mode for GigabitEthernet X/X. Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # duplex auto 4.2.65.18 end Command: end end Go back to EXEC mode Default: Auto Usage Guide: To back to EXEC mode Example: To back to EXEC mode Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # end Switch# 4.2.65.
PAGE 106
Command Guide Usage Guide: To configure EVC DEI mode Example: To configure EVC DEI mode (Colored) for GigabitEthernet X/X. Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # evc dei colored 4.2.65.
PAGE 107
Command Guide Select BPDU addresses (0-15) and GARP addresses (16-31) Default: N/A Usage Guide: To configure policy ID of L2CP forward Example: To configure policy 1 for L2CP forward for GigabitEthernet X/X Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # evc l2cp forward 1 4.2.65.
PAGE 108
Command Guide 4.2.65.23 evc update dei Command: evc update dei colored | fixed evc Ethernet Virtual Connections update Update existing entry dei Setup DEI mode colored Allow policer to set DEI fixed Use classified DEI Default: Fixed Usage Guide: To update EVC DEI mode Example: To update EVC DEI mode (Colored) for GigabitEthernet X/X. Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # evc update dei colored 4.2.65.
PAGE 109
Command Guide 4.2.65.25 exit Command: exit exit Exit from current mode Default: None Usage Guide: To exit current mode Example: To exit current mode. Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # exit Switch (config)# 4.2.65.26 flow control Command: flowcontrol off | on flowcontrol Traffic flow control. off Disable flow control. on Enable flow control.
PAGE 110
Command Guide 4.2.65.27 green-ethernet energy-detect(GG) Command: green-ethernet energy-detect green-ethernet Green ethernet (Power reduction) energy-detect Enable power saving for ports with no link partner. Default: N/A Usage Guide: To enable power saving for ports with no link partner Example: To enable power saving for ports with no link for GigabitEthernet X/X Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # green-ethernet energy-detect 4.2.65.
PAGE 111
Command Guide 4.2.65.29 gvrp join-request vlan(GG) Command: gvrp join-request vlan gvrp Enable GVRP on port(s) join-request Emit a Join-Request for test purpose Default: N/A Usage Guide: To send GVRP Join-Request to specific interface Example: To send GVRP Join-Request(VLAN 1) to GigabitEthernet X/X Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # gvrp join-request vlan 1 4.2.65.
PAGE 112
Command Guide 4.2.65.
PAGE 113
Command Guide Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # ip arp inspection logging all 4.2.65.
PAGE 114
Command Guide Switch (config)# interface GigabitEthernet X/X Switch (config-if) # ip dhcp snooping trust 4.2.65.
PAGE 115
Command Guide 4.2.65.37 ip igmp snooping max-groups Command: ip igmp snooping max-groups max-groups IGMP group throttling configuration Maximum number of IGMP group registration Default: Unlimited Usage Guide: To limit maximum number of IGMP group for specific interface Example: To limit 5 groups of IGMP for GigabitEthernet X/X Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # ip igmp snooping max-groups 5 4.2.65.
PAGE 116
Command Guide 4.2.65.39 ip verify source Command: ip verify source Default: Disabled Usage Guide: To enable IP Source Guard for specific interface Example: To enable IP Source Guard for GigabitEthernet X/X Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # ip verify source 4.2.65.
PAGE 117
Command Guide 4.2.65.41 ipv6 mld snooping filter Command: ipv6 mld snooping filter filter Access control on MLD multicast group registration Profile name in 16 words Default: N/A Usage Guide: To apply the MLD Snooping filter ID for specific interface Example: To apply the MLD Snooping filter ID 1 for GigabitEthernet X/X Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # ipv6 mld snooping filter 1 4.2.65.
PAGE 118
Command Guide 4.2.65.43 ipv6 mld snooping max-groups Command: ipv6 mld snooping max-groups max-groups IGMP group throttling configuration Maximum number of IGMP group registration Default: Unlimited Usage Guide: To limit maximum number of MLD group for specific interface Example: To limit 5 groups of MLD for GigabitEthernet X/X Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # ipv6 mld snooping max-groups 5 4.2.65.
PAGE 119
Command Guide 4.2.65.45 lacp Command: lacp lacp Enable LACP on this interface Default: Disabled Usage Guide: To enable LACP for specific interface Example: To enable LACP for GigabitEthernet X/X Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # lacp 4.2.65.
PAGE 120
Command Guide 4.2.65.47 lacp port-priority Command: lacp port-priority <1-65535> lacp Enable LACP on this interface port-priority LACP priority of the port <1-65535> Priority value, lower means higher priority Default: 32768 Usage Guide: To configure LACP port-priority for specific interface Example: To configure LACP port-priority (555) for GigabitEthernet X/X Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # lacp port-priority 555 4.2.65.
PAGE 121
Command Guide 4.2.65.
PAGE 122
Command Guide 4.2.65.
PAGE 123
Command Guide Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # lldp med transmit-tlv capabilities location 4.2.65.53 lldp receive Command: lldp receive lldp LLDP configurations receive Enable/Disable decoding of received LLDP frames.
PAGE 124
Command Guide Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # lldp tlv-select management-address 4.2.65.55 lldp tlv-select port-description Command: lldp tlv-select port-description lldp LLDP configurations tlv-select To transmit which optional TLVs. port-description Enable/Disable transmission of port description.
PAGE 125
Command Guide Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # lldp tlv-select system-capabilities 4.2.65.57 lldp tlv-select system-description Command: lldp tlv-select system-description lldp LLDP configurations tlv-select To transmit which optional TLVs. system-description Enable/Disable transmission of system description.
PAGE 126
Command Guide Example: To enable system-name of LLDP TLV for GigabitEthernet X/X Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # lldp tlv-select system-name 4.2.65.59 lldp transmit Command: lldp transmit lldp LLDP configurations transmit Enable/Disabled transmission of LLDP frames.
PAGE 127
Command Guide Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # loop-protect 4.2.65.
PAGE 128
Command Guide Example: To enable tx-mode of Loop protection for GigabitEthernet X/X Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # loop-protect tx-mode 4.2.65.
PAGE 129
Command Guide Usage Guide: To enable learning of MAC address table for specific interface Example: To enable learning of MAC address table for GigabitEthernet X/X Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # mac address-table learning 4.2.65.65 media-type Command: media-type dual | rj45 | sfp media-type Media type. dual Dual media interface (copper & fiber interface). rj45 rj45 interface (copper interface). sfp sfp interface (fiber interface).
PAGE 130
Command Guide Usage Guide: To configure MTU sizes for specific interface Example: To configure MTU sizes (9000) for GigabitEthernet X/X Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # mtu 9000 4.2.65.
PAGE 131
Command Guide Default: Inactive Usage Guide: To configure port role of specific MVR profile for specific interface Example: To configure port role (source) of MVR profiles (111) for GigabitEthernet X/X Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # mvr name 111 type source 4.2.65.
PAGE 132
Command Guide 4.2.65.70 network-clock synchronization ssm Command: network-clock synchronization ssm network-clock synchronization ssm network-clock SSM enable/disable. SSM enable/disable. Default: Disable Usage Guide: To enable SSM of SyncE for specific interface Example: To enable SSM of SyncE for GigabitEthernet X/X Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # network-clock synchronization ssm 4.2.65.
PAGE 133
Command Guide 4.2.65.72 ping ip Command: ping ip size ping The ping command allows you to test connectivity to a network host from the appliance ip ip size IP address size Default is 56 (excluding MAC, IP and ICMP headers) Default: N/A Usage Guide: To run Ping function for specific interface Example: To run Ping function (IP address: 10.10.10.10 with size 88 bytes) for GigabitEthernet X/X.
PAGE 134
Command Guide Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # poe mode plus 4.2.65.74 poe pdcheck IP Command: poe pdcheck IP poe Power Over Ethernet. pdcheck Allows user to enable or disable per port PD Alive Check function. IP To set PoE device IP address here for system making ping to the PoE device.
PAGE 135
Command Guide Default: N/A Usage Guide: To configure PD Ping Alive Check Action of PoE for specific interface Example: To configure PD Ping Alive Check Action (Alarm) of PoE for GigabitEthernet X/X. Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # poe pdcheck action alarm 4.2.65.76 poe pdcheck enable Command: poe pdcheck enable poe Power Over Ethernet. pdcheck Allows user to enable or disable per port PD Alive Check function. enable PD alive check enable.
PAGE 136
Command Guide 4.2.65.77 poe pdcheck interval Command: poe pdcheck interval <10-300> poe Power Over Ethernet. pdcheck Allows user to enable or disable per port PD Alive Check function. interval set how long system should be issue a ping request to PD for detecting whether PD is alive or dead. <10-300> interval <10~300> Default: 30 Usage Guide: To configure PD Ping Alive Check interval of PoE for specific interface.
PAGE 137
Command Guide Switch (config)# interface GigabitEthernet X/X Switch (config-if) # poe pdcheck reboot-time 100 4.2.65.79 poe pdcheck retry-count Command: poe pdcheck retry-count <1-5> poe Power Over Ethernet. pdcheck Allows user to enable or disable per port PD Alive Check function. retry-count set how many times system retry ping to PD. <1-5> retry-count <1-5> Default: 2 Usage Guide: To configure PD Ping Alive Check retry count of PoE for specific interface.
PAGE 138
Command Guide Example: To configure maximum power (29 watts) of PoE for GigabitEthernet X/X. Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # poe power limit 29 4.2.65.81 poe priority Command: poe priority { low | high | critical } poe Power Over Ethernet. priority Interface priority. critical Set priority to critical. high Set priority to high. low Set priority to low.
PAGE 139
Command Guide Default: Profile 1 Usage Guide: To configure time-range profile of PoE for specific interface. Example: To configure time-range profile (Profile 3) of PoE for GigabitEthernet X/X. Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # poe time-range profile3 4.2.65.83 port-security Command: port-security port-security Enable/disable port security per interface.
PAGE 140
Command Guide Default: None Usage Guide: To configure number of Port-security addresses for specific interface Example: To configure 100 Port-security addresses for GigabitEthernet X/X Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # port-security maximum 100 4.2.65.85 port-security violation Command: port-security violation [protect | shutdown | trap | trap-shutdown] port-security violation Enable/disable port security per interface.
PAGE 141
Command Guide 4.2.65.86 port-security violation Command: port-security violation [protect | shutdown | trap | trap-shutdown] port-security violation Enable/disable port security per interface. The action involved with exceeding the limit.
PAGE 142
Command Guide Switch (config)# interface GigabitEthernet X/X Switch (config-if) # pvlan 5 4.2.65.88 pvlan isolation Command: pvlan isolation pvlan Private VLAN isolation Port isolation Default: None Usage Guide: To enable PVLAN isolation for specific interface Example: To enable PVLAN isolation for GigabitEthernet X/X Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # pvlan isolation 4.2.65.
PAGE 143
Command Guide Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # qos cos 4 4.2.65.
PAGE 144
Command Guide Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # qos dpl 1 4.2.65.
PAGE 145
Command Guide Usage Guide: To configure DSCP egress remarking of QoS for specific interface Example: To configure DSCP egress remarking (Remap) of QoS for GigabitEthernet X/X Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # qos dscp-remark remap 4.2.65.
PAGE 146
Command Guide dpl Specify drop precedence level pcp Specific drop precedence level or range Specify PCP (Priority Code Point) dei Specific PCP Specify DEI (Drop Eligible Indicator) Specific DEI Default: Disabled Usage Guide: To configure (QoS class, DP level) to (PCP, DEI) Mapping of QoS for specific interface Example: To configure (QoS class, DP level) to (PCP, DEI) Mapping of QoS as below table for GigabitEthernet X/X Switch# configure terminal Switch (confi
PAGE 147
Command Guide Usage Guide: To configure (PCP, DEI) to (QoS class, DP level) Mapping of QoS for specific interface Example: To configure (PCP, DEI) to (QoS class, DP level) Mapping of QoS as below table for GigabitEthernet X/X Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # qos map tag-cos pcp 4 dei 0 cos 5 dpl 1 4.2.65.
PAGE 148
Command Guide 4.2.65.98 qos policer Command: qos policer qos Quality of Service policer Policer configuration Policer rate (default kbps) Default: 0 Usage Guide: To configure Ingress Port Policers Rate of QoS for specific interface Example: To configure Ingress Port Policers Rate (9999 Kbps) of QoS for GigabitEthernet X/X Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # qos policer 9999 4.2.65.
PAGE 149
Command Guide Switch (config)# interface GigabitEthernet X/X Switch (config-if) # qos queue-policer queue 4 9999 4.2.65.
PAGE 150
Command Guide Example: To configure Egress Port (4) Shapers Rate (9999 Kbps) of QoS for GigabitEthernet X/X Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # qos queue-shaper queue 4 9999 4.2.65.
PAGE 151
Command Guide Default: 500 Usage Guide: To configure Unicast Frames Storm Control Rate of QoS for specific interface Example: To configure Unicast Frames Storm Control Rate (999 Kbps) of QoS for GigabitEthernet X/X Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # qos storm unicast 999 4.2.65.
PAGE 152
Command Guide 4.2.65.
PAGE 153
Command Guide Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # qos tag-remark mapped 4.2.65.
PAGE 154
Command Guide Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # qos trust tag 4.2.65.109 rmon collection history Command: rmon collection history <1-65535> buckets <1-65535> interval <1-3600> rmon Configure Remote Monitoring on an interface collection Configure Remote Monitoring Collection on an interface history Configure history buckets interval Requested buckets of intervals. Default is 50 buckets Interval to sample data for each bucket.
PAGE 155
Command Guide 4.2.65.
PAGE 156
Command Guide 4.2.65.112 spanning-tree Command: spanning-tree spanning-tree Spanning Tree protocol Default: Disabled Usage Guide: To enable STP for specific interface Example: To enable STP for GigabitEthernet X/X Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # spanning-tree 4.2.65.
PAGE 157
Command Guide 4.2.65.114 spanning-tree bpdu-guard Command: spanning-tree bpdu-guard spanning-tree Spanning Tree protocol auto-edge Auto detects edge status Default: Disabled Usage Guide: To enable BPDU Guard of CIST Normal Port Configuration for specific interface Example: To enable BPDU Guard of CIST Normal Port Configuration for GigabitEthernet X/X Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # spanning-tree bpdu-guard 4.2.65.
PAGE 158
Command Guide 4.2.65.
PAGE 159
Command Guide Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # spanning-tree mst 0 cost 100 4.2.65.118 spanning-tree mst cost Command: spanning-tree mst port-priority spanning-tree Spanning Tree protocol mst STP bridge instance instance port-priority 0-7 (CIST=0, MST2=1...
PAGE 160
Command Guide Default: Disabled Usage Guide: To enable Restricted-role of CIST Normal Port Configuration for specific interface Example: To enable Restricted-role of CIST Normal Port Configuration for GigabitEthernet X/X Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # spanning-tree restricted-role 4.2.65.
PAGE 161
Command Guide 10 10Mbps 100 100Mbps 1000 1Gbps 10g 10Gbps auto Auto negotiation Default: Auto Usage Guide: To configure line speed for specific interface Example: To configure line speed (1Gbps) for GigabitEthernet X/X Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # speed 1000 4.2.65.
PAGE 162
Command Guide 4.2.65.123 switchport forbidden vlan add Command: switchport forbidden vlan add switchport Switching mode characteristics forbidden Adds or removes forbidden VLANs from the current list of forbidden VLANs vlan Add or modify VLAN entry in forbidden table. add Add to existing list.
PAGE 163
Command Guide Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # switchport forbidden vlan remove 5 4.2.65.125 switchport hybrid acceptable-frame-type Command: switchport hybrid acceptable-frame-type all | tagged | untagged switchport Switching mode characteristics hybrid Change PVID for hybrid port acceptable-frame-type all Set acceptable frame type on a port.
PAGE 164
Command Guide add Add VLANs to the current list all All VLANs except All VLANs except the following none No VLANs remove Remove VLANs from the current list Default: All Usage Guide: To configure VLAN list of Hybrid VLAN for specific interface Example: To configure VLAN list (None) of Hybrid VLAN for GigabitEthernet X/X Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # switchport hybrid allowed vlan none 4.2.65.
PAGE 165
Command Guide 4.2.65.
PAGE 166
Command Guide 4.2.65.130 switchport hybrid port-type Command: switchport hybrid port-type c-port | s-custom-port | s-port | unaware switchport Switching mode characteristics hybrid Change PVID for hybrid port port-type Set port type c-port Customer port s-custom-port Custom Provider port s-port Provider port unaware Port in not aware of VLAN tags.
PAGE 167
Command Guide To configure VLAN mode for specific interface Example: To configure VLAN mode (trunk) for GigabitEthernet X/X Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # switchport mode trunk 4.2.65.132 switchport vlan ip-subnet Command: switchport vlan ip-subnet id <1-128> vlan switchport Switching mode characteristics vlan VLAN commands ip-subnet VCL IP Subnet-based VLAN configuration.
PAGE 168
Command Guide 4.2.65.
PAGE 169
Command Guide Example: To configure Group mapping (Group 25) for GigabitEthernet X/X Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # switchport vlan mapping 25 4.2.65.
PAGE 170
Command Guide switchport voice Switching mode characteristics Voice appliance attributes vlan Vlan for voice traffic discovery-protocol both Set Voice VLAN port discovery protocol Detect telephony device by OUI address and LLDP lldp Detect telephony device by LLDP oui Detect telephony device by OUI address Default: OUI Usage Guide: To configure Discovery-protocol in the Voice VLAN for specific interface Example: To configure Discovery-protocol (LLDP) in the Voice VLAN for GigabitEthernet X/X Swi
PAGE 171
Command Guide Switch (config)# interface GigabitEthernet X/X Switch (config-if) # switchport voice vlan mode auto 4.2.65.
PAGE 172
Command Guide Switch# configure terminal Switch (config)# interface vlan 1 Switch (config-if-vlan)# 4.2.66.1 do Command: do < exec commands > do To run exec commands in config mode Default: N/A Usage Guide: To run exec commands in configure terminal mode Example: To run “show aaa” in configure terminal mode. Switch# configure terminal Switch (config)# interface vlan X Switch (config-if-vlan)# do show aaa console : local telnet ssh http : local : local : local 4.2.66.
PAGE 173
Command Guide Switch# configure terminal Switch (config)# interface vlan X Switch (config-if-vlan)# end Switch# 4.2.66.3 exit Command: exit exit Exit from current mode Default: None Usage Guide: To exit current mode Example: To exit current mode. Switch# configure terminal Switch (config)# interface vlan X Switch (config-if-vlan)# exit Switch (config)# 4.2.66.
PAGE 174
Command Guide Example: To configure IP address mode (192.168.1.10/24) for VLAN X Switch# configure terminal Switch (config)# interface vlan X Switch (config-if-vlan)# ip address 192.168.1.10 255.255.255.0 4.2.66.
PAGE 175
Command Guide To configure DHCP fallback IP address for specific VLAN Example: To configure DHCP fallback IP address (192.168.1.10/24) for VLAN X Switch# configure terminal Switch (config)# interface vlan X Switch (config-if-vlan)# ip address dhcp fallback 192.168.1.10 255.255.255.0 4.2.66.
PAGE 176
Command Guide Default: Disabled Usage Guide: To enable IGMP snooping for specific VLAN Example: To enable IGMP snooping for VLAN X Switch# configure terminal Switch (config)# interface vlan X Switch (config-if-vlan)# ip igmp snooping 4.2.66.
PAGE 177
Command Guide 4.2.66.
PAGE 178
Command Guide Switch# configure terminal Switch (config)# interface vlan X Switch (config-if-vlan)# ip igmp snooping priority 5 4.2.66.12 ip igmp snooping querier address Command: ip igmp snooping querier address ip Interface Internet Protocol config commands igmp Internet Group Management Protocol snooping Snooping IGMP querier IGMP Querier configuration address IGMP Querier address configuration A valid IPv4 unicast address Default: 0.0.0.
PAGE 179
Command Guide Default: Enabled Usage Guide: To enable Querier-election of IGMP snooping for specific VLAN Example: To enable Querier-election of IGMP snooping for VLAN X Switch# configure terminal Switch (config)# interface vlan X Switch (config-if-vlan)# ip igmp snooping querier election 4.2.66.
PAGE 180
Command Guide 4.2.66.
PAGE 181
Command Guide Switch# configure terminal Switch (config)# interface vlan X Switch (config-if-vlan)# ip igmp snooping robustness-variable 88 4.2.66.
PAGE 182
Command Guide Example: To configure IPv6 address (2001::7788/64) for VLAN X Switch# configure terminal Switch (config)# interface vlan X Switch (config-if-vlan)# ipv6 address 2001::7788/64 4.2.66.
PAGE 183
Command Guide Default: Auto Usage Guide: To configure MLD snooping version for specific VLAN Example: To configure MLD snooping V2 for VLAN X Switch# configure terminal Switch (config)# interface vlan X Switch (config-if-vlan)# ipv6 mld snooping compatibility v2 4.2.66.
PAGE 184
Command Guide ipv6 IPv6 configuration commands mld Multicast Listener Discovery snooping Snooping MLD priority Interface CoS priority CoS priority ranges from 0 to 7 Default: 0 Usage Guide: To configure CoS priority of MLD snooping for specific VLAN Example: To configure CoS priority (5) of MLD snooping for VLAN X Switch# configure terminal Switch (config)# interface vlan X Switch (config-if-vlan)# ipv6 mld snooping priority 5 4.2.66.
PAGE 185
Command Guide 4.2.66.
PAGE 186
Command Guide Switch# configure terminal Switch (config)# interface vlan X Switch (config-if-vlan)# ipv6 mld snooping query-max-response-time 600 4.2.66.
PAGE 187
Command Guide Usage Guide: To configure Unsolicited-Report-Interval of MLD snooping for specific VLAN Example: To configure Unsolicited-Report-Interval (99 seconds) of MLD snooping for VLAN X Switch# configure terminal Switch (config)# interface vlan X Switch (config-if-vlan)# ipv6 mld snooping unsolicited-report-interval 99 4.2.66.
PAGE 188
Command Guide Example: To enable ARP inspection Switch# configure terminal Switch (config)# ip arp inspection 4.2.
PAGE 189
Command Guide 4.2.69 ip arp inspection translate Command: ip arp inspection translate ip Internet Protocol arp Address Resolution Protocol inspection translate ARP inspection arp inspection translate all entries Default: N/A Usage Guide: To translate dynamic entries into static ARP inspection table. Example: To translate dynamic entries into static ARP inspection table.
PAGE 190
Command Guide Usage Guide: To translate dynamic entries into static ARP inspection table for specific interface. Example: To translate below dynamic entries into static ARP inspection table for GigabitEthernet 1/1. Switch# configure terminal Switch (config)# ip arp inspection translate interface GigabitEthernet 1/1 1 00:11:22:33:44:55 192.168.0.18 4.2.
PAGE 191
Command Guide 4.2.72 ip dhcp excluded-address Command: ip dhcp excluded-address ip Internet Protocol dhcp Dynamic Host Configuration Protocol excluded-address Prevent DHCP from assigning certain addresses Low IP address Default: N/A Usage Guide: To configure excluded IP range of DHCP Server. Example: To configure excluded IP range (192.168.0.100~192.168.0.101) of DHCP Server. Switch# configure terminal Switch (config)# ip dhcp excluded-address 192.168.0.100 192.168.0.101 4.2.
PAGE 192
Command Guide 4.2.73.1 broadcast Command: broadcast broadcast Broadcast address in use on the client's subnet Broadcast IP address Default: None Usage Guide: To configure Broadcast IP address (DHCP option 28) of DHCP Server Example: To configure Broadcast IP address (192.168.0.66) of DHCP Server for pool “planetbestswitch” Switch# configure terminal Switch (config)# ip dhcp pool planetbestswitch Switch (config-dhcp-pool)# broadcast 192.168.0.66 4.2.73.
PAGE 193
Command Guide 4.2.73.
PAGE 194
Command Guide 4.2.73.5 default-router Command: default-router default-router Default routers Router's IP address Default: None Usage Guide: To configure Default Gateway of DHCP Server Example: To configure Default Gateway (192.168.0.1) of DHCP Server for pool “planetbestswitch” Switch# configure terminal Switch (config)# ip dhcp pool planetbestswitch Switch (config-dhcp-pool)# default-router 192.168.0.1 4.2.73.6 dns-server Command: dns-server dns-server DNS servers
PAGE 195
Command Guide 4.2.73.7 do Command: do < exec commands > do To run exec commands in config mode Default: N/A Usage Guide: To run exec commands Example: To run “show aaa”. Switch# configure terminal Switch (config)# ip dhcp pool planetbestswitch Switch (config-dhcp-pool)# do show aaa console : local telnet ssh http : local : local : local 4.2.73.
PAGE 196
Command Guide 4.2.73.9 end Command: end end Go back to EXEC mode Default: Auto Usage Guide: To back to EXEC mode Example: To back to EXEC mode Switch# configure terminal Switch (config)# ip dhcp pool planetbestswitch Switch (config-dhcp-pool)# end Switch# 4.2.73.10 exit Command: exit exit Exit from current mode Default: None Usage Guide: To exit current mode Example: To exit current mode.
PAGE 197
Command Guide 4.2.73.11 hardware-address Command: hardware-address hardware-address Client hardware address Client MAC address Default: None Usage Guide: To configure MAC address of DHCP Server while the pool is in the host type. Example: To configure MAC address (00:11:22:33:44:55) of DHCP Server for pool “planetbestswitch” while the pool is in the host type.
PAGE 198
Command Guide 4.2.73.13 lease Command: lease <0-365> <0-23> <0-59> | infinite lease Address lease time <0-365> Days <0-23> Hours <0-59> Minutes infinite Infinite lease Default: 1 day Usage Guide: To configure Lease Time of DHCP Server. Example: To configure Lease Time (119 minutes) of DHCP Server for pool “planetbestswitch”. Switch# configure terminal Switch (config)# ip dhcp pool planetbestswitch Switch (config-dhcp-pool)# lease 0 1 59 4.2.73.
PAGE 199
Command Guide 4.2.73.15 netbios-node-type Command: netbios-node-type b-node | h-node | m-node | p-node netbios-node-type NetBIOS node type b-node Broadcast node h-node Hybrid node m-node Mixed node p-node Peer-to-peer node Default: None Usage Guide: To configure NetBIOS node type of DHCP Server. Example: To configure NetBIOS node type (B-node) of DHCP Server for pool “planetbestswitch”.
PAGE 200
Command Guide 4.2.73.17 network Command: network network Network number and mask Network number Network mask in dotted-decimal notation, excluding 255.255.255.255 Default: None Usage Guide: To configure Network IP address of DHCP Server. Example: To configure Network IP address (192.168.1.11/24) of DHCP Server for pool “planetbestswitch”.
PAGE 201
Command Guide 4.2.73.19 nis-server Command: nis-server nis-server Network information servers Server's IP address Default: None Usage Guide: To configure NIS Server of DHCP Server Example: To configure NIS Server (1.1.1.1) of DHCP Server for pool “planetbestswitch” Switch# configure terminal Switch (config)# ip dhcp pool planetbestswitch Switch (config-dhcp-pool)# nis-server 1.1.1.1 4.2.73.
PAGE 202
Command Guide 4.2.73.21 ntp-server Command: ntp-server ntp-server NTP servers Server's IP address Default: None Usage Guide: To configure NTP Server of DHCP Server Example: To configure NTP Server (1.1.1.1) of DHCP Server for pool “planetbestswitch” Switch# configure terminal Switch (config)# ip dhcp pool planetbestswitch Switch (config-dhcp-pool)# ntp-server 1.1.1.1 4.2.73.
PAGE 203
Command Guide Switch# configure terminal Switch (config)# ip dhcp pool planetbestswitch Switch (config-dhcp-pool)# vendor class-identifier "0x8" specific-info 0x8 4.2.74 ip dns proxy Command: ip dns proxy ip Internet Protocol dns Domain Name System proxy DNS proxy service Default: Disabled Usage Guide: To enable DNS proxy. Example: To enable DNS proxy. Switch# configure terminal Switch (config)# ip dns proxy 4.2.
PAGE 204
Command Guide Example: To configure IP address (1.1.1.1) of DHCP. Switch# configure terminal Switch (config)# ip helper-address 1.1.1.1 4.2.76 ip http secure-redirect Command: ip http secure-redirect ip Internet Protocol http Hypertext Transfer Protocol secure-redirect Secure HTTP web redirection Default: Disabled Usage Guide: To redirect WebUI from HTTP to HTTPs Example: To redirect WebUI from HTTP to HTTPs Switch# configure terminal Switch (config)# ip http secure-redirect 4.2.
PAGE 205
Command Guide Usage Guide: To enable HTTPs WebUI. Example: To enable HTTPs WebUI. Switch# configure terminal Switch (config)# ip http secure-server 4.2.78 ip igmp host-proxy Command: ip igmp host-proxy ip Internet Protocol igmp Internet Group Management Protocol host-proxy IGMP proxy configuration Default: Disabled Usage Guide: To enable IGMP Proxy Example: To enable IGMP Proxy. Switch# configure terminal Switch (config)# ip igmp host-proxy 4.2.
PAGE 206
Command Guide Default: Disabled Usage Guide: To enable IGMP leave-proxy Example: To enable IGMP leave-proxy. Switch# configure terminal Switch (config)# ip igmp host-proxy leave-proxy 4.2.80 ip igmp snooping Command: ip igmp snooping ip Internet Protocol igmp Internet Group Management Protocol snooping Snooping IGMP Default: Disabled Usage Guide: To enable IGMP Snooping. Example: To enable IGMP Snooping. Switch# configure terminal Switch (config)# ip igmp snooping 4.2.
PAGE 207
Command Guide Default: Disabled Usage Guide: To enable IGMP Snooping for specific VLAN. Example: To enable IGMP Snooping for VLAN 1. Switch# configure terminal Switch (config)# ip igmp snooping vlan 1 4.2.
PAGE 208
Command Guide 4.2.83 ip igmp unknown-flooding Command: ip igmp unknown-flooding ip Internet Protocol igmp Internet Group Management Protocol unknown-flooding Flooding unregistered IPv4 multicast traffic Default: Enabled Usage Guide: To flood unregistered IPv4 multicast traffic. Example: To flood unregistered IPv4 multicast traffic. Switch# configure terminal Switch (config)# ip igmp unknown-flooding 4.2.
PAGE 209
Command Guide 4.2.85 ip name-server dhcp Command: ip name-server dhcp ip Internet Protocol name-server dhcp Domain Name System Dynamic Host Configuration Protocol Default: None Usage Guide: To configure DNS IP address via DHCP Server. Example: To configure DNS IP address via DHCP Server. Switch# configure terminal Switch (config)# ip name-server 8.8.8.8 4.2.
PAGE 210
Command Guide 4.2.87 ip route Command: ip route ip Internet Protocol route Add IP route Network Netmask Gateway Default: None Usage Guide: To configure static route Example: To configure static route as below table. Switch# configure terminal Switch (config)# ip route 192.168.1.0 255.255.255.0 192.168.0.1 4.2.
PAGE 211
Command Guide Switch# configure terminal Switch (config)# ip routing 4.2.
PAGE 212
Command Guide To enable SSH service Example: To enable SSH service Switch# configure terminal Switch (config)# ip ssh 4.2.91 ip verify source Command: ip verify source ip Internet Protocol verify verify command source verify source Default: Disabled Usage Guide: To enable IP Source Guard Example: To enable IP Source Guard Switch# configure terminal Switch (config)# ip verify source 4.2.
PAGE 213
Command Guide Usage Guide: To translate dynamic entries to IP Source Guard table Example: To translate dynamic entries to IP Source Guard table Switch# configure terminal Switch (config)# ip verify source translate 4.2.93 ipmc profile Command: ipmc profile ipmc IPv4/IPv6 multicast configuration profile IPMC profile configuration Default: Disabled Usage Guide: To enable IPMC profile Example: To enable IPMC profile Switch# configure terminal Switch (config)# ipmc profile 4.2.
PAGE 214
Command Guide Usage Guide: To enter IPMC profile mode Example: To enter IPMC profile mode (planet) Switch# configure terminal Switch (config)# ipmc profile planet Switch (config-ipmc-profile)# 4.2.94.
PAGE 215
Command Guide Default: None Usage Guide: To configure description for specific IPMC Profile Example: To configure description (999) for specific IPMC Profile (planet) Switch# configure terminal Switch (config)# ipmc profile planet Switch (config-ipmc-profile)# description 999 4.2.94.3 do Command: do < exec commands > do To run exec commands in config mode Default: N/A Usage Guide: To run exec commands Example: To run “show aaa”.
PAGE 216
Command Guide Default: Auto Usage Guide: To back to EXEC mode Example: To back to EXEC mode Switch# configure terminal Switch (config)# ipmc profile planet Switch (config-ipmc-profile)#end Switch# 4.2.94.5 exit Command: exit exit Exit from current mode Default: None Usage Guide: To exit current mode Example: To exit current mode. Switch# configure terminal Switch (config)# ipmc profile planet Switch (config-ipmc-profile)# exit Switch (config)# 4.2.94.
PAGE 217
Command Guide Default: N/A Usage Guide: To default the function. Example: To enable the function (description 999). Switch# configure terminal Switch (config)# ipmc profile planet Switch (config-ipmc-profile)# no description 999 4.2.94.
PAGE 218
Command Guide mld Multicast Listener Discovery host-proxy MLD proxy configuration Default: Disabled Usage Guide: To enable MLD Proxy Example: To enable MLD Proxy. Switch# configure terminal Switch (config)# ipv6 mld host-proxy 4.2.
PAGE 219
Command Guide snooping Snooping MLD Default: Disabled Usage Guide: To enable MLD Snooping. Example: To enable MLD Snooping. Switch# configure terminal Switch (config)# ipv6 mld snooping 4.2.98 ipv6 mld snooping vlan Command: ipv6 mld snooping vlan ipv6 IPv6 configuration commands mld Multicast Listener Discovery snooping vlan Snooping MLD MLD VLAN VLAN identifier(s): VID Default: Disabled Usage Guide: To enable MLD Snooping for specific VLAN.
PAGE 220
Command Guide ipv6 IPv6 configuration commands mld Multicast Listener Discovery ssm-range IPv6 address range of Source Specific Multicast Valid IPv6 multicast address Prefix length ranges from 8 to 128 Default: ff3e:: /96 Usage Guide: To enable SSM Range of MLD. Example: To enable SSM Range (ff3e::7788/128) of MLD. Switch# configure terminal Switch (config)# ipv6 mld ssm-range ff3e::7788 128 4.2.
PAGE 221
Command Guide 4.2.
PAGE 222
Command Guide 4.2.102 lacp system-priority Command: lacp system-priority <1-65535> lacp LACP settings system-priority <1-65535> System priority Priority value, lower means higher priority Default: 32768 Usage Guide: To configure LACP system-priority. Example: To configure LACP system-priority (99). Switch# configure terminal Switch (config)# lacp system-priority 99 4.2.
PAGE 223
Command Guide 4.2.103.1 do Command: do < exec commands > do To run exec commands. Default: N/A Usage Guide: To run exec commands. Example: To run “show aaa”. Switch# configure terminal Switch (config)# line vty 1 Switch (config-line)# do show aaa console : local telnet ssh http : local : local : local 4.2.103.2 editing Command: editing editing Enable command line editing Default: Enabled Usage Guide: To allow user editing command line. Example: To allow user editing command line.
PAGE 224
Command Guide 4.2.103.3 end Command: end end Go back to EXEC mode Default: None Usage Guide: To back to EXEC mode Example: To back to EXEC mode Switch# configure terminal Switch (config)# line vty 1 Switch (config-line)#end Switch# 4.2.103.
PAGE 225
Command Guide 4.2.103.5 exec-timeout Command: exec-timeout <0-1440> exec-timeout <0-1440> Set the EXEC timeout Timeout in minutes Default: N/A Usage Guide: To configure EXEC timeout Example: To configure EXEC timeout (10 minutes) Switch# configure terminal Switch (config)# line vty 1 Switch (config-line)# exec-timeout 10 4.2.103.
PAGE 226
Command Guide 4.2.103.7 exit Command: exit exit Exit from current mode Default: None Usage Guide: To exit current mode Example: To exit current mode. Switch# configure terminal Switch (config)# line vty 1 Switch (config-line)# exit Switch (config)# 4.2.103.
PAGE 227
Command Guide 4.2.103.9 length Command: length <0 or 3-512> length Set number of lines on a screen <0 or 3-512> Number of lines on screen (0 for no pausing) Default: None Usage Guide: To configure displayed lines on a screen. Example: To configure displayed lines on a screen. Switch# configure terminal Switch (config)# line vty 1 Switch (config-line)# length 10 4.2.103.
PAGE 228
Command Guide 4.2.103.11 motd-banner Command: motd-banner motd-banner Enable the display of the MOTD banner Default: Enabled Usage Guide: To enable MOTD banner. Example: To enable MOTD banner.. Switch# configure terminal Switch (config)# line vty 1 Switch (config-line)# motd-banner 4.2.103.
PAGE 229
Command Guide 4.2.103.13 privilege level Command: privilege level <0-15> privilege level Change privilege level for line Assign default privilege level for line <0-15> Default privilege level for line Default: 15 Usage Guide: To configure privilege level Example: To configure privilege level (5) for vty 1. Switch# configure terminal Switch (config)# line vty 1 Switch (config-line)# privilege level 5 4.2.103.
PAGE 230
Command Guide 4.2.104 lldp holdtime Command: lldp holdtime <2-10> lldp LLDP configurations. holdtime Sets LLDP hold time (The neighbor switch will discarded the LLDP information after "hold time" multiplied with "timer" seconds ). <2-10> 2-10 seconds Default: 4 Usage Guide: To enable LLDP hold time Example: To enable LLDP hold time (5) Switch# configure terminal Switch (config)# lldp holdtime 5 4.2.
PAGE 231
Command Guide Switch# configure terminal Switch (config)# lldp med datum nad83-mllw 4.2.106 lldp med fast Command: lldp med fast <1-10> lldp LLDP configurations. med Media Endpoint Discovery fast Number of times to repeat LLDP frame transmission at fast start. Default: 4 Usage Guide: To configure frame transmission time of LLDP Example: To configure frame transmission time (6) of LLDP Switch# configure terminal Switch (config)# lldp med fast 6 4.2.
PAGE 232
Command Guide Switch# configure terminal Switch (config)# lldp med location-tlv altitude floors 5 4.2.108 lldp med location-tlv elin-addr Command: lldp med location-tlv elin-addr lldp LLDP configurations. med Media Endpoint Discovery location-tlv elin-addr LLDP-MED Location Type Length Value parameter Emergency Location Identification Number, (e.g. E911 and others), such as defined by TIA or NENA.
PAGE 233
Command Guide Default: North, 0 Usage Guide: To configure latitude direction of LLDP-MED Example: To configure latitude direction (south, 5) of LLDP-MED Switch# configure terminal Switch (config)# lldp med location-tlv latitude south 5 4.2.110 lldp med location-tlv longitude Command: lldp med location-tlv longitude east | west lldp LLDP configurations.
PAGE 234
Command Guide lldp LLDP configurations. med Media Endpoint Discovery media-vlan-policy Use the media-vlan-policy to create a policy, which can be assigned to an interface. Policy id for the policy which is created. guest-voice Create a guest voice policy. guest-voice-signaling Create a guest voice signaling policy. softphone-voice Create a softphone voice policy. streaming-video Create a streaming video policy. video-conferencing Create a video conferencing policy.
PAGE 235
Command Guide <1-10> 1-10 seconds. Default: 2 Usage Guide: To configure Tx re-initialization delay time of LLDP Example: To configure Tx re-initialization delay time (5) of LLDP Switch# configure terminal Switch (config)# lldp reinit 5 4.2.113 lldp timer Command: lldp timer <5-32768> lldp LLDP configurations. timer Sets LLDP TX interval (The time between each LLDP frame transmitted in seconds) <5-32768> 5-32768 seconds.
PAGE 236
Command Guide transmission-delay Sets LLDP transmission-delay. LLDP transmission delay (the amount of time that the transmission of LLDP frames will delayed after LLDP configuration has changed) in seconds.) <1-8192> 1-8192 seconds. Default: 2 Usage Guide: To configure Tx transmission-delay time of LLDP Example: To configure Tx transmission-delay time (88) of LLDP Switch# configure terminal Switch (config)# lldp transmission-delay 88 4.2.
PAGE 237
Command Guide level level error Error info Information warning Warning Default: Info Usage Guide: To configure level of log server Example: To configure level of log server Switch# configure terminal Switch (config)# logging level error 4.2.117 logging on Command: logging on logging on Syslog Enable syslog server Default: Disabled Usage Guide: To enable log server Example: To enable log server Switch# configure terminal Switch (config)# logging on 4.2.
PAGE 238
Command Guide Default: Disabled Usage Guide: To enable Loop Protection Example: To enable Loop Protection Switch# configure terminal Switch (config)# loop-protect 4.2.
PAGE 239
Command Guide Default: 5 Usage Guide: To configure Transmission Time of Loop Protection Example: To configure Transmission Time (8) of Loop Protection Switch# configure terminal Switch (config)# loop-protect transmit-time 8 4.2.
PAGE 240
Command Guide vlan 48 bit MAC address: xx:xx:xx:xx:xx:xx VLAN keyword VLAN IDs 1-4095 interface * Select an interface to configure All switches or All ports GigabitEthernet 1 Gigabit Ethernet Port 10GigabitEthernet 10 Gigabit Ethernet Port Default: 300 Usage Guide: To configure Static MAC Address Table Example: To configure Static MAC Address Table as below table Switch# configure terminal Switch (config)# mac address-table static 00:11:22:33:44:55 vlan 1 interface GigabitEt
PAGE 241
Command Guide Switch# configure terminal Switch (config)# mep 1 ais fr1s 4.2.124 mep aps Command: mep aps [ multi | uni ] { laps | { raps [ octet ] } } mep Maintenance Entity Point The MEP instance number. aps Automatic Protection Switching protocol laps Linear Automatic Protection Switching protocol. multi OAM PDU is transmitted with multicast MAC. Must me 'multi' in case of RAPS. uni OAM PDU is transmitted with unicast MAC.
PAGE 242
Command Guide 4.2.125 mep cc Command: mep cc fr100s | fr10s | fr1m | fr1s | fr300s | fr6h | fr6m mep Maintenance Entity Point The MEP instance number. cc Continuity Check Priority in case of tagged OAM. In the EVC domain this is the COS-ID. fr100s Frame rate is 100 f/s. fr10s Frame rate is 10 f/s. fr1m Frame rate is 1 f/min. fr1s Frame rate is 1 f/s. fr300s Frame rate is 300 f/s. fr6h Frame rate is 6 f/hour.
PAGE 243
Command Guide vlan Vlan Domain Default: EVC Usage Guide: To configure Client Domain of MEP Example: To configure Client Domain (EVC) of MEP 1 Switch# configure terminal Switch (config)# mep 1 client domain evc 4.2.127 mep client flow Command: mep client flow level [ ais-prio [ | ais-highest ] ] [ lck-prio [ | lck-highest ] ] mep Maintenance Entity Point level The MEP instance number.
PAGE 244
Command Guide Switch# configure terminal Switch (config)# mep 1 client flow 5 level 4 ais-prio ais-highest lck-prio 3 4.2.128 mep dm Command: mep dm [ multi | { uni mep-id } ] [ single | dual ] [ rdtrp | flow ] interval last-n mep Maintenance Entity Point The MEP instance number. dm Delay Measurement Priority in case of tagged OAM.
PAGE 245
Command Guide Switch# configure terminal Switch (config)# mep 1 dm 5 rdtrp interval 10 last-n 10 4.2.129 mep dm ns Command: mep dm ns mep Maintenance Entity Point The MEP instance number. dm Delay Measurement ns Nano Seconds Default: us Usage Guide: To configure Delay Measurement of MEP Example: To configure Delay Measurement unit (ns) of MEP 1 as below table. Switch# configure terminal Switch (config)# mep 1 dm ns 4.2.
PAGE 246
Command Guide Default: Keep Usage Guide: To reset Delay Measurement of MEP while overflowing Example: To reset Delay Measurement of MEP 1 while overflowing Switch# configure terminal Switch (config)# mep 1 dm overflow-reset 4.2.131 mep dm proprietary Command: mep dm proprietary mep Maintenance Entity Point dm The MEP instance number. Delay Measurement proprietary Proprietary Delay Measurement Default: Standard Usage Guide: To configure Tx mode (proprietary) of MEP.
PAGE 247
Command Guide Default: Enabled Usage Guide: To configure Time Sync of MEP. Example: To configure Time Sync of MEP 1 Switch# configure terminal Switch (config)# mep 1 dm synchronized 4.2.133 mep down Command: mep [ mip ] down domain { port | evc | vlan } [ vid ] flow level interface mep Maintenance Entity Point mip This MEP instance is a half-MIP down The MEP instance number.
PAGE 248
Command Guide Switch# configure terminal Switch (config)# mep 1 down domain port flow 1 level 0 interface GigabitEthernet 1/1 4.2.134 mep lb Command: mep lb [ dei ] [ multi | { uni { { mep-id } | { mac } } } ] count size interval mep Maintenance Entity Point lb The MEP instance number. Loop Back count Priority in case of tagged OAM. In the EVC domain this is the COS-ID.
PAGE 249
Command Guide Switch# configure terminal Switch (config)# mep 2 lb 1 dei count 10 size 64 interval 100 4.2.135 mep lck Command: mep lck fr1m | fr1s mep Maintenance Entity Point lck fr1m fr1s The MEP instance number. Locked Signal Frame rate is 1 f/min. Frame rate is 1 f/s. Default: 1 frame/sec Usage Guide: To configure Locked Frame Rate of MEP. Example: To configure Locked Frame Rate (1 frame/sec) of MEP 2.
PAGE 250
Command Guide Usage Guide: To configure MEG level of MEP. Example: To configure MEG level (2) of MEP 2. Switch# configure terminal Switch (config)# mep 2 level 2 4.2.137 mep lm Command: mep lm [ multi | uni ] [ single | dual ] [ fr10s | fr1s | fr6m | fr1m | fr6h ] [ flr ] mep Maintenance Entity Point lm The MEP instance number. Loss Measurement Priority in case of tagged OAM. In the EVC domain this is the COS-ID.
PAGE 251
Command Guide Switch# configure terminal Switch (config)# mep 2 lm 5 uni flr 4 4.2.138 mep lt Command: mep lt { { mep-id } | { mac } } ttl mep Maintenance Entity Point lt The MEP instance number. Link Trace mac Priority in case of tagged OAM. In the EVC domain this is the COS-ID. Link Trace target unicast MAC to be used in case of LT against MIP. mep-id Peer MEP-ID for Link Trace target unicast MAC.
PAGE 252
Command Guide 4.2.139 mep meg-id Command: mep meg-id { itu | itu-cc | { ieee [ name ] } } mep Maintenance Entity Point meg-id The MEP instance number. The ITU/IEEE MEG-ID The MEG-ID string. This is either the ITU MEG-ID or the IEEE Short MA, depending on the selected MEG-ID format. The ITU max. is 13 characters. The ITU-CC max. is 15 characters. The IEEE max. is 16 characters..
PAGE 253
Command Guide The MEP-ID value. Default: None Usage Guide: To configure MEP-ID of MEP. Example: To configure MEP-ID (5) of MEP 1. Switch# configure terminal Switch (config)# mep 1 mep-id 5 4.2.141 mep peer-mep-id Command: mep peer-mep-id [ mac ] mep Maintenance Entity Point The MEP instance number. peer-mep-id The peer MEP-ID The peer MEP-ID value mac The peer MAC.
PAGE 254
Command Guide 4.2.142 mep performance-monitoring Command: mep performance-monitoring mep Maintenance Entity Point The MEP instance number. performance-monitoring Performance monitoring Data Set collection (MEF35) Default: Disabled Usage Guide: To enable Performance Monitoring of MEP. Example: To enable Performance Monitoring of MEP 1 Switch# configure terminal Switch (config)# mep 1 performance-monitoring 4.2.
PAGE 255
Command Guide size The TST frame size. This is entered as the wanted size (in bytes) of a un-tagged frame containing TST OAM PDU - including CRC (four bytes). Example when 'Size' = 64 => Un-tagged frame size = DMAC(6) + SMAC(6) + TYPE(2) + TST PDU LENGTH(46) + CRC(4) = 64 Frame size value Default: Usage Guide: To enable Test Signal of MEP.
PAGE 256
Command Guide Default: None Usage Guide: To configure Up-MEP of MEP. Example: To configure Up-MEP of MEP 2 as below table Switch# configure terminal Switch (config)# mep 2 up domain port vid 1 flow 1 level 2 interface GigabitEthernet 1/1 4.2.145 mep vid Command: mep vid mep Maintenance Entity Point The MEP instance number. vid The MEP VID The MEP VID value Default: 0 Usage Guide: To set VID of MEP. Example: To set VID (8) of MEP 1.
PAGE 257
Command Guide voe The MEP instance number. MEP is VOE based Default: 0 Usage Guide: To set VOE of MEP. Example: To set VOE (8) of MEP 1 Switch# configure terminal Switch (config)# mep 1 voe 4.2.147 monitor destination Command: monitor destination interface 10GigabitEthernet | GigabitEthernet monitor Set monitor configuration destination The destination port.
PAGE 258
Command Guide source The source port(s). That is the ports to be mirrored to the destination port. Default: Disabled Usage Guide: To configure Mirrored Port Example: To set Mirrored Port (GigabitEthernet 1/1, Tx + Rx) Switch# configure terminal Switch (config)# monitor source interface GigabitEthernet 1/1 both 4.2.149 mvr Command: mvr mvr Multicast VLAN Registration configuration Default: Disabled Usage Guide: To enable MVR Example: To enable MVR Switch# configure terminal Switch (config)# mvr 4.2.
PAGE 259
Command Guide Profile name Default: None Usage Guide: To configure channel interface of MVR profile Example: To configure channel interface (1) of MVR profile (123) Switch# configure terminal Switch (config)# mvr name 123 channel 1 4.2.
PAGE 260
Command Guide mvr name frame tagged mvr Multicast VLAN Registration configuration name MVR multicast name MVR multicast VLAN name frame MVR control frame in TX tagged Tagged IGMP/MLD frames will be sent Default: None Usage Guide: To configure frame tagged of MVR profile Example: To configure frame tagged (frame tagged) of MVR profile (123) Switch# configure terminal Switch (config)# mvr name 123 frame tagged 4.2.
PAGE 261
Command Guide 4.2.
PAGE 262
Command Guide Switch# configure terminal Switch (config)# mvr name 123 mode compatible 4.2.156 mvr vlan Command: mvr vlan mvr Multicast VLAN Registration configuration vlan MVR multicast vlan MVR multicast VLAN list Default: None Usage Guide: To create a profile of MVR VLAN Example: To create a profile of MVR VLAN (5) Switch# configure terminal Switch (config)# mvr vlan 5 4.2.
PAGE 263
Command Guide Example: To configure the channel (1) of MVR VLAN (5) Switch# configure terminal Switch (config)# mvr vlan 5 channel 1 4.2.
PAGE 264
Command Guide Default: Enabled Usage Guide: To enable the IGMP/MLD frame tagged of MVR VLAN Example: To enable the IGMP/MLD frame tagged of MVR VLAN (123) Switch# configure terminal Switch (config)# mvr vlan 123 tagged 4.2.
PAGE 265
Command Guide MVR multicast VLAN list last-member-query-interval Last Member Query Interval in tenths of seconds 0 - 31744 tenths of seconds Default: 5 Usage Guide: To configure the Last Member Query Interval of MVR VLAN Example: To configure the Last Member Query Interval (50 seconds) of MVR VLAN (123) Switch# configure terminal Switch (config)# mvr vlan 123 last-member-query-interval 500 4.2.
PAGE 266
Command Guide 4.2.163 mvr vlan name Command: mvr vlan name mvr Multicast VLAN Registration configuration vlan MVR multicast vlan name MVR multicast VLAN list MVR multicast name Default: None Usage Guide: To configure profile name of MVR VLAN Example: To configure profile name (6) of MVR VLAN (5) Switch# configure terminal Switch (config)# mvr vlan 5 name 6 4.2.
PAGE 267
Command Guide Switch# configure terminal Switch (config)# network-clock clk-source 1 aneg-mode slave 4.2.165 no Command: no no Negate a command or set its defaults Default: N/A Usage Guide: To default the function Example: To disable the function (loop-protect) Switch# configure terminal Switch (config)# no loop-protect 4.2.
PAGE 268
Command Guide 4.2.167 ntp server Command: ntp server <1-5> ip-address { | | } ntp Configure NTP server Configure NTP server <1-5> index number domain name ipv4 address ipv6 address Default: None Usage Guide: To configure the IP addresses of NTP Server Example: To configure the IP address (9.9.9.9) of NTP Server for index 1 Switch# configure terminal Switch (config)# ntp server 1 ip-address 9.9.9.9 4.2.
PAGE 269
Command Guide Switch# configure terminal Switch (config)# poe admin-mode enable 4.2.169 poe management mode Command: poe management mode allocation-consumption | { class-consumption | allocation-reserved-power class-reserved-power | | | lldp-consumption lldp-reserved-power } poe Power Over Ethernet management mode Use management mode to configure PoE power management method. mode allocation-consumption Max.
PAGE 270
Command Guide sequential enable PoE sequential is to delay power feeding when the switch is completely booted. poe sequential enable Default: Enabled Usage Guide: To enable Sequential Power up Option. Example: To enable Sequential Power up Option. Switch# configure terminal Switch (config)# poe sequential enable 4.2.
PAGE 271
Command Guide poe Power Over Ethernet sequential rule port PoE sequential is to delay power feeding when the switch is completely booted. System sequential feeding power the PoE interfaces based port number. priority Use priority command to configure sequential feeding power to PoE interfaces based on port PoE priority. Default: Port Usage Guide: To configure Sequential Power up Port Option. Example: To configure Sequential Power up Port Option (Priority).
PAGE 272
Command Guide temperature-protection enable Configure PoE over temperature protection to enable or disable. poe temperature-protection enable Default: Enabled Usage Guide: To enable PoE Temperature Protection. Example: To enable PoE Temperature Protection. Switch# configure terminal Switch (config)# poe temperature-protection enable 4.2.
PAGE 273
Command Guide usage-threshold The poe usage-threshold command sets a percentage threshold above which the system sends a log or SNMP trap.<1-99>: The -threshold percentage configured with this command. <1-99> The usage-threshold percentage configured with this command. Default: 85 Usage Guide: To configure PoE Usage Threshold. Example: To configure PoE Usage Threshold (90 %). Switch# configure terminal Switch (config)# poe usage-threshold 90 4.2.
PAGE 274
Command Guide 4.2.177.1 do Command: do < exec commands > do To run exec commands Default: N/A Usage Guide: To run exec commands Example: To run “show aaa”. Switch# configure terminal Switch (config)# poe-time-range profile1 Switch (config-poe-time-range)#do show aaa console : local telnet : local ssh http : local : local 4.2.177.
PAGE 275
Command Guide 4.2.177.3 exit Command: exit exit Exit from current mode Default: None Usage Guide: To exit current mode Example: To exit current mode. Switch# configure terminal Switch (config)# poe-time-range profile1 Switch (config-poe-time-range)#exit Switch (config)# 4.2.177.4 no Command: no no Negate a command or set its defaults Default: N/A Usage Guide: To default the function. Example: To enable the function (description 999).
PAGE 276
Command Guide periodic { Mon | Tue | Wed | Thu | Fri | Sat | Sun } to [ reboot ] periodic Fri To create a periodic mode time-range for the PoE time-range of the switch. Periodic Mode, with Friday. Mon Periodic Mode, with Monday. Sat Periodic Mode, with Saturday. Sun Periodic Mode, with Sunday. Thu Periodic Mode, with Thursday. Tue Periodic Mode, with Tuesday. Wed Periodic Mode, with Wednesday.
PAGE 277
Command Guide 4.2.177.6 reboot-only Command: reboot-only { Mon | Tue | Wed | Thu | Fri | Sat | Sun } reboot-only Fri To create a periodic mode time-range for the PoE time-range of the switch. Periodic Mode, with Friday. Mon Periodic Mode, with Monday. Sat Periodic Mode, with Saturday. Sun Periodic Mode, with Sunday. Thu Periodic Mode, with Thursday. Tue Periodic Mode, with Tuesday. Wed Periodic Mode, with Wednesday.
PAGE 278
Command Guide Usage Guide: To enable the Port Security Example: To enable the Port Security Switch# configure terminal Switch (config)# port-security 4.2.179 port-security aging Command: port-security aging port-security aging Enable/disable port security globally Enable/disable port security aging Default: Disabled Usage Guide: To enable the Port Aging Example: To enable the Port Aging Switch# configure terminal Switch (config)# port-security port-security aging 4.2.
PAGE 279
Command Guide Default: 3600 Usage Guide: To configure the Aging Period of Port Security Example: To configure the Aging Period (159) of Port Security Switch# configure terminal Switch (config)# port-security aging time 159 4.2.
PAGE 280
Command Guide Switch# configure terminal Switch (config)# privilege dhcp-pool level 12 host 4.2.
PAGE 281
Command Guide Default: 0 Usage Guide: To configure the DSCP Classification Example: To configure the DSCP Classification (QoS Class 3: DSCP CS1) Switch# configure terminal Switch (config)# qos map cos-dscp 3 dscp cs1 4.2.
PAGE 282
Command Guide va Voice Admit PHB(DSCP 44) Default: Disabled Usage Guide: To enabled the DSCP Ingress Classification Example: To configure the DSCP Ingress Classification (DSCP 36) Switch# configure terminal Switch (config)# qos map dscp-classify af42 4.2.
PAGE 283
Command Guide cs5 Class Selector PHB CS5 precedence 5(DSCP 40) cs6 Class Selector PHB CS6 precedence 6(DSCP 48) cs7 Class Selector PHB CS7 precedence 7(DSCP 56) ef Expedited Forwarding PHB(DSCP 46) va Voice Admit PHB(DSCP 44) cos Specify class of service dpl Specific class of service Specify drop precedence level Specific drop precedence level Default: 0 Usage Guide: To configure the DSCP-Based QoS Ingress Classification Example: To configure the DSCP-Based QoS Ingres
PAGE 284
Command Guide af33 Assured Forwarding PHB AF33(DSCP 30) af41 Assured Forwarding PHB AF41(DSCP 34) af42 Assured Forwarding PHB AF42(DSCP 36) af43 Assured Forwarding PHB AF43(DSCP 38) be Default PHB(DSCP 0) for best effort traffic cs1 Class Selector PHB CS1 precedence 1(DSCP 8) cs2 Class Selector PHB CS2 precedence 2(DSCP 16) cs3 Class Selector PHB CS3 precedence 3(DSCP 24) cs4 Class Selector PHB CS4 precedence 4(DSCP 32) cs5 Class Selector PHB CS5 precedence 5(DSCP 40) cs6 Class Selector
PAGE 285
Command Guide af21 Assured Forwarding PHB AF21(DSCP 18) af22 Assured Forwarding PHB AF22(DSCP 20) af23 Assured Forwarding PHB AF23(DSCP 22) af31 Assured Forwarding PHB AF31(DSCP 26) af32 Assured Forwarding PHB AF32(DSCP 28) af33 Assured Forwarding PHB AF33(DSCP 30) af41 Assured Forwarding PHB AF41(DSCP 34) af42 Assured Forwarding PHB AF42(DSCP 36) af43 Assured Forwarding PHB AF43(DSCP 38) be Default PHB(DSCP 0) for best effort traffic cs1 Class Selector PHB CS1 precedence 1(DSCP 8) cs2
PAGE 286
Command Guide [ { | any } ] } | { llc [ dsap { | any } ] [ ssap { | any } ] [ control { | any } ] } | { snap [ { | any } ] } | { ipv4 [ proto { | tcp | udp | any } ] [ sip { | any } ] [ dip { | any } ] [ dscp { | { be | af11 | af12 | af13 | af21 | af22 | af23 | af31 | af32 | af33 | af41 | af42 | af43 | cs1 | cs2 | cs3 | cs4 | cs5 | cs6 | cs7 | ef | va } | any } ] [ fragment { yes | no | any } ] [ sport { | any } ]
PAGE 287
Command Guide Switch# configure terminal Switch (config)# qos qce 1 interface GigabitEthernet 1/1-2 tag type tagged vid 5 pcp 3 dei 1 dmac unicast frame-type ipv4 proto udp dscp 19 frag no sport 55 action cos 0 dpl 1 dscp 4 4.2.
PAGE 288
Command Guide [ pcp-dei { | default } ] [ dscp { | { be | af11 | af12 | af13 | af21 | af22 | af23 | af31 | af32 | af33 | af41 | af42 | af43 | cs1 | cs2 | cs3 | cs4 | cs5 | cs6 | cs7 | ef | va } | default } ] [ policy { | default } ] } ] qos Quality of Service qce QoS Control Entry update Update an existing QCE action Setup action dmac Setup matched DMAC frame-type interface Setup matched frame type Interfaces last Place QCE at the end
PAGE 289
Command Guide To refresh the QCE. Switch# configure terminal Switch (config)# qos qce refresh 4.2.
PAGE 290
Command Guide Switch# configure terminal Switch (config)# qos wred queue 1 min-th 2 mdp-1 3 mdp-2 4 mdp-3 5 4.2.191 radius-server attribute 32 Command: radius-server attribute 32 radius-server 32 Configure RADIUS NAS-Identifier Default: None Usage Guide: To configure the NAS-Identifier Example: To configure the NAS-Identifier (planet) Switch# configure terminal Switch (config)# radius-server attribute 32 planet 4.2.
PAGE 291
Command Guide Usage Guide: To configure the NAS-IP-Address Example: To configure the NAS-IP-Address (7.7.7.7) Switch# configure terminal Switch (config)# radius-server attribute 4 7.7.7.7 4.2.
PAGE 292
Command Guide Usage Guide: To configure the Deadtime of Radius-Server Example: To configure the Deadtime (15) of Radius-Server Switch# configure terminal Switch (config)# radius-server deadtime 15 4.2.
PAGE 293
Command Guide 4.2.196 radius-server key Command: radius-server key radius-server key Configure RADIUS Set RADIUS encryption key The shared key Default: None Usage Guide: To configure the Key of Radius-Server Example: To configure the Key (123456789) of Radius-Server Switch# configure terminal Switch (config)# radius radius-server key 123456789 4.2.
PAGE 294
Command Guide 4.2.198 radius-server timeout Command: radius-server timeout radius-server timeout Configure RADIUS Time to wait for a RADIUS server to reply Wait time in seconds Default: 5 Usage Guide: To configure the timeout of Radius-Server Example: To configure the timeout (10) of Radius-Server Switch# configure terminal Switch (config)# radius-server timeout 10 4.2.
PAGE 295
Command Guide ifOutDiscards The number of outbound packets that are discarded event the packets is normal ifOutErrors The number of outbound packets that could not be transmitted because of errors ifOutNUcastPkts ifOutOctets The number of broad-cast and multi-cast packets that request to transmit The number of octets transmitted out of the interface, including framing characters ifIndex absolute Sample interval Test each sample directly delta Test delta between sa
PAGE 296
Command Guide Event description log Generate RMON log when the event fires trap Generate SNMP trap when the event fires SNMP community string Default: None Usage Guide: To configure the Event of RMON Example: To configure the Event (below table) of RMON Switch# configure terminal Switch (config)# rmon event 1 log trap planet description error 4.2.
PAGE 297
Command Guide 4.2.202 sflow collector-address Command: sflow collector-address sflow Statistics flow collector-address Collector address IPv4 address or IPv6 address or hostname identifying the collector receiver Default: None Usage Guide: To configure the Collector address of sFlow Example: To configure the Collector address (10.10.10.10) of sFlow Switch# configure terminal Switch (config)# sflow collector-address 10.10.10.10 4.2.
PAGE 298
Command Guide 4.2.204 sflow max-datagram-size Command: sflow max-datagram-size sflow Statistics flow max-datagram-size Maximum datagram size bytes Default: None Usage Guide: To configure the Collector Maximum datagram size of sFlow Example: To configure the Collector Maximum datagram size (555 bytes) of sFlow Switch# configure terminal Switch (config)# sflow max-datagram-size 555 4.2.
PAGE 299
Command Guide 4.2.206 sfp temperature-threshold Command: sfp temperature-threshold <0-100> sfp temperature-threshold Set a lower high temperature threshold for the secondary temperature alarm in degrees C. <0-100> Specifies the new threshold temperature. Default: None Usage Guide: To configure the SFP temperature-threshold of sFlow Example: To configure the SFP temperature-threshold (55 degrees C) of sFlow Switch# configure terminal Switch (config)# sfp temperature-threshold 55 4.2.
PAGE 300
Command Guide 4.2.
PAGE 301
Command Guide 4.2.
PAGE 302
Command Guide Default: None Usage Guide: To configure the sysContact string of SNMP Example: To configure the sysContact string (Server123) of SNMP Switch# configure terminal Switch (config)# snmp-server contact Server123 4.2.
PAGE 303
Command Guide Default: None Usage Guide: To enter the SNMP host mode Example: To enter the SNMP host mode (planet) Switch# configure terminal Switch (config)# snmp-server host planet Switch (config-snmps-host)# 4.2.212.1 do Command: do < exec commands > do To run exec commands. Default: N/A Usage Guide: To run exec commands. Example: To run “show aaa”.
PAGE 304
Command Guide Default: Auto Usage Guide: To back to EXEC mode Example: To back to EXEC mode Switch# configure terminal Switch (config)# snmp-server host planet Switch (config-snmps-host)#end Switch# 4.2.212.3 exit Command: exit exit Exit from current mode Default: None Usage Guide: To exit current mode Example: To exit current mode. Switch# configure terminal Switch (config)# snmp-server host planet Switch (config-snmps-host)#exit Switch (config)# 4.2.212.
PAGE 305
Command Guide host host configuration hostname of SNMP trap host IP address of SNMP trap host IP address of SNMP trap host informs traps UDP port of the trap messages Send Inform messages to this host Send Trap messages to this host Default: None Usage Guide: To configure Trap Host of SNMP Example: To configure Trap Host (below table) of SNMP Switch# configure terminal Switch (config)# snmp-server host planet Switch (config-snmps-host)# ho
PAGE 306
Command Guide 4.2.212.
PAGE 307
Command Guide To disable Trap mode of SNMP Switch# configure terminal Switch (config)# snmp-server host planet Switch (config-snmps-host)# shutdown 4.2.212.
PAGE 308
Command Guide 4.2.212.
PAGE 309
Command Guide Example: To enter aggregation mode of STP Switch# configure terminal Switch (config)# spanning-tree aggregation Switch (config-stp-aggr)# 4.2.213.1 do Command: do < exec commands > do To run exec commands. Default: N/A Usage Guide: To run exec commands. Example: To run “show aaa”. Switch# configure terminal Switch (config)# spanning-tree aggregation Switch (config-stp-aggr)#do show aaa console : local telnet ssh http : local : local : local 4.2.213.
PAGE 310
Command Guide Example: To back to EXEC mode Switch# configure terminal Switch (config)# spanning-tree aggregation Switch (config-stp-aggr)#end Switch# 4.2.213.3 exit Command: exit exit Exit from current mode Default: None Usage Guide: To exit current mode Example: To exit current mode. Switch# configure terminal Switch (config)# spanning-tree aggregation Switch (config-stp-aggr)#exit Switch (config)# 4.2.213.
PAGE 311
Command Guide Example: To disable the function (spanning-tree auto-edge) Switch# configure terminal Switch (config)# snmp-server host planet Switch (config-snmps-host)# no spanning-tree auto-edge 4.2.213.
PAGE 312
Command Guide Example: To enable the BPDU Guard of CIST Aggregated Port Switch# configure terminal Switch (config)# snmp-server host planet Switch (config-snmps-host)# spanning-tree bpdu-guard 4.2.213.
PAGE 313
Command Guide Usage Guide: To configure the Point to Point mode (Shared) of CIST Aggregated Port Example: To configure the Point to Point mode (Shared) of CIST Aggregated Port Switch# configure terminal Switch (config)# snmp-server host planet Switch (config-snmps-host)# spanning-tree link-type shared 4.2.213.
PAGE 314
Command Guide mst STP bridge instance port-priority instance 0-7 (CIST=0, MST1=1...) STP priority of this port Range (lower higher priority) Default: Auto Usage Guide: To configure the Port Priority of MSTI Port Example: To configure the Port Priority (96) of MSTI Port (MST 2) Switch# configure terminal Switch (config)# snmp-server host planet Switch (config-snmps-host)# spanning-tree mst 2 port-priority 96 4.2.213.
PAGE 315
Command Guide 4.2.213.12 spanning-tree restricted-tcn Command: spanning-tree restricted-tcn spanning-tree Spanning Tree protocol restricted-tcn Restrict topology change notifications Default: Disabled Usage Guide: To enable the Restricted TCN of CIST Example: To enable the Restricted TCN of CIST Switch# configure terminal (config)# spanning-tree aggregation (config-stp-aggr)# spanning-tree restricted-tcn 4.2.
PAGE 316
Command Guide Switch# configure terminal Switch (config)# switchport vlan mapping 1 3 5 4.2.215 tacacs-server deadtime Command: tacacs-server deadtime tacacs-server deadtime Configure TACACS+ Time to stop using a TACACS+ server that doesn't respond Time in minutes Default: 0 Usage Guide: To configure the Deadtime of TACACS+ Server Example: To enable the Deadtime (6) of TACACS+ Server Switch# configure terminal Switch (config)# tacacs-server deadtime 6 4.2.
PAGE 317
Command Guide Usage Guide: To configure the Host of TACACS+ Server Example: To enable the Host (below table) of TACACS+ Server Switch# configure terminal Switch (config)# tacacs-server host planet.com port 55 timeout 6 key 7788 4.2.217 transport email authentication Command: transport email authentication username password transport email Enable or disable transport email function. Enable or disable transport email function.
PAGE 318
Command Guide subject mail address subject/title of the email email title Default: N/A Usage Guide: To configure SMTP sender's email address and title of the email Example: To configure SMTP sender's email address (sys@planet.com.tw) and title of the email (syserror) Switch# configure terminal Switch (config)# transport email from sys@planet.com.tw subject syserror 4.2.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/mgsw-28240f/user-s-manual-catalan-english-french-dutch/page-319.html>PAGE 319</a></h6><p>Command Guide 4.2.220 transport email to Command: transport email to <1 | 2> <mail_addr> transport email to Enable or disable transport email function. Enable or disable transport email function. receiver's email <1|2> 1: mail address 1 <mail_addr> 2: mail address 2 mail address Default: N/A Usage Guide: To configure SMTP destination mail address. Example: To configure SMTP destination mail address 1 (ss@planet.com.tw). Switch# configure terminal Switch (config)# transport email to 1 ss@planet.com.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/mgsw-28240f/user-s-manual-catalan-english-french-dutch/page-320.html>PAGE 320</a></h6><p>Command Guide 4.2.222 upnp advertising-duration Command: upnp advertising-duration <100-86400> upnp Set UPnP's configurations advertising-duration <100-86400> Set advertising duration advertising duration Default: 100 Usage Guide: To configure the Advertising Duration of UPnP Example: To configure the Advertising Duration (123) of UPnP Switch# configure terminal Switch (config)# upnp advertising-duration 123 4.2.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/mgsw-28240f/user-s-manual-catalan-english-french-dutch/page-321.html>PAGE 321</a></h6><p>Command Guide 4.2.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/mgsw-28240f/user-s-manual-catalan-english-french-dutch/page-322.html>PAGE 322</a></h6><p>Command Guide Default: None Usage Guide: To create the VLAN Profiles Example: To create the VLAN Profiles (VLAN 5) Switch# configure terminal Switch (config)# vlan 5 Switch (config-vlan)# 4.2.225.1 do Command: do < exec commands > do To run exec commands. Default: N/A Usage Guide: To run exec commands. Example: To run “show aaa”. Switch# configure terminal Switch (config)# vlan 5 Switch (config-vlan)#do show aaa console : local telnet ssh http : local : local : local 4.2.225.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/mgsw-28240f/user-s-manual-catalan-english-french-dutch/page-323.html>PAGE 323</a></h6><p>Command Guide Default: Auto Usage Guide: To back to EXEC mode Example: To back to EXEC mode Switch# configure terminal Switch (config)# vlan 5 Switch (config-vlan)#end Switch# 4.2.225.3 exit Command: exit exit Exit from current mode Default: None Usage Guide: To exit current mode Example: To exit current mode Switch# configure terminal Switch (config)# vlan 5 Switch (config-vlan)# exit Switch (config)# 4.2.225.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/mgsw-28240f/user-s-manual-catalan-english-french-dutch/page-324.html>PAGE 324</a></h6><p>Command Guide Default: None Usage Guide: To configure description of VLAN Example: To configure description (FAE) of VLAN Switch# configure terminal Switch (config)# vlan 5 Switch (config-vlan)# name FAE 4.2.225.5 no Command: no no Negate a command or set its defaults Default: N/A Usage Guide: To default the function Example: To disable the function (name FAE) Switch# configure terminal Switch (config)# vlan 5 Switch (config-vlan)# no name FAE 4.2.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/mgsw-28240f/user-s-manual-catalan-english-french-dutch/page-325.html>PAGE 325</a></h6><p>Command Guide <etype> Ethertype (Range: 0x0600-0xffff) Default: 0x88A8 Usage Guide: To create the Ethernet type of Custom S-ports Example: To create the Ethernet type (0x88A9) of Custom S-ports Switch# configure terminal Switch (config)# vlan ethertype s-custom-port 0x88a9 4.2.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/mgsw-28240f/user-s-manual-catalan-english-french-dutch/page-326.html>PAGE 326</a></h6><p>Command Guide Example: To configure the Protocol-based VLAN (below table) Switch# configure terminal Switch (config)# vlan protocol llc 0x55 0x66 group 3 4.2.228 voice vlan Command: voice vlan voice Voice appliance attributes vlan Vlan for voice traffic Default: Disabled Usage Guide: To enable the Voice VLAN service Example: To enable the Voice VLAN service Switch# configure terminal Switch (config)# voice vlan 4.2.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/mgsw-28240f/user-s-manual-catalan-english-french-dutch/page-327.html>PAGE 327</a></h6><p>Command Guide Usage Guide: To configure the Aging Time of Voice VLAN Example: To configure the Aging Time of Voice VLAN Switch# configure terminal Switch (config)# voice vlan aging-time 8888 4.2.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/mgsw-28240f/user-s-manual-catalan-english-french-dutch/page-328.html>PAGE 328</a></h6><p>Command Guide Default: None Usage Guide: To configure the OUI of Voice VLAN Example: To configure the OUI (OUI: 00:45:89, Description: qwe ) of Voice VLAN Switch# configure terminal Switch (config)# voice vlan oui 00:45:89 description qwe 4.2.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/mgsw-28240f/user-s-manual-catalan-english-french-dutch/page-329.html>PAGE 329</a></h6><p>Command Guide group Web privilege group <vlan_id> VLAN ID, 1-4095 <group_name> Valid words are 'Aggregation' 'DHCP' 'Debug' 'Dhcp_Client' 'Diagnostics' 'EPS' 'ERPS' 'ETH_LINK_OAM' 'EVC' 'Green_Ethernet' 'IP2' 'IPMC_Snooping' 'LACP' 'LLDP' 'Loop_Protect' 'MAC_Table' 'MEP' 'MVR' 'Maintenance' 'Mirroring' 'NTP' 'POE' 'PTP' 'Ports' 'Private_VLANs' 'QoS' 'RPC' 'Security' 'Spanning_Tree' 'System' 'Timer' 'UPnP' 'VCL' 'VLAN_Translation' 'VLANs' 'Voice_VLAN' 'XXRP' 'ZL_3034X_API' level Web privilege group le</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/mgsw-28240f/user-s-manual-catalan-english-french-dutch/page-330.html>PAGE 330</a></h6><p>Command Guide Default: None Usage Guide: To copy configuration from source to destination Example: To copy configuration from source (running-config) to destination (startup-config) Switch# copy running-config startup-config 4.4 debug 4.4.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/mgsw-28240f/user-s-manual-catalan-english-french-dutch/page-331.html>PAGE 331</a></h6><p>Command Guide delete Delete one file in flash: file system <path : word> Name of file to delete Default: None Usage Guide: To delete Configuration File of Flash Example: To delete Configuration File (222) of Flash Switch # copy running-config flash:222 Building configuration... % Saving 1833 bytes to flash:222 Switch # dir Directory of flash: r- 1970-01-01 00:00:00 648 default-config rw 1970-01-01 07:26:26 1833 startup-config rw 1970-01-01 00:18:40 1833 222 3 files, 4314 bytes total.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/mgsw-28240f/user-s-manual-catalan-english-french-dutch/page-332.html>PAGE 332</a></h6><p>Command Guide Default: None Usage Guide: To list directory of file system Example: To list directory of file system Switch # dir Directory of flash: r- 1970-01-01 00:00:00 648 default-config rw 1970-01-01 07:26:26 1833 startup-config 2 files, 2481 bytes total. 4.7 disable 4.7.1 disable Command: disable disable Turn off privileged commands Default: None Usage Guide: To exit enable mode Example: To exit enable mode Switch # disable Switch > 4.8 do 4.8.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/mgsw-28240f/user-s-manual-catalan-english-french-dutch/page-333.html>PAGE 333</a></h6><p>Command Guide do < exec commands > do To run exec commands. Default: N/A Usage Guide: To run exec commands. Example: To run “show aaa”. Switch# do show aaa console : local telnet ssh : local : local http : local 4.9 dot1x 4.9.1 dot1x initialize Command: dot1x initialize [ interface ( <port_type> [ <plist> ] ) ] dot1x IEEE Standard for port-based Network Access Control initialize Force re-authentication immediately Default: N/A Usage Guide: To re-authenticate specific interface immediately.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/mgsw-28240f/user-s-manual-catalan-english-french-dutch/page-334.html>PAGE 334</a></h6><p>Command Guide 4.10 enable 4.10.1 enable Command: enable enable Turn on privileged commands Default: None Usage Guide: To enter enable mode Example: To enter enable mode Switch > enable Switch # 4.11 erps 4.11.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/mgsw-28240f/user-s-manual-catalan-english-french-dutch/page-335.html>PAGE 335</a></h6><p>Command Guide Example: To configure Instance Command (below table) of Group (1) Switch # erps 1 command force port0 4.12 exit 4.12.1 exit Command: exit exit Exit from EXEC mode Default: None Usage Guide: To exit EXEC mode Example: To exit EXEC mode Switch # disable Switch > exit Press ENTER to get started 4.13 firmware 4.13.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/mgsw-28240f/user-s-manual-catalan-english-french-dutch/page-336.html>PAGE 336</a></h6><p>Command Guide Default: None Usage Guide: To swap Active and Alternate firmware image Example: To swap Active and Alternate firmware image Switch # firmware swap 4.13.2 firmware upgrade Command: firmware upgrade <tftpserver_path_file> firmware Firmware upgrade/swap upgrade Firmware upgrade <tftpserver_path_file : word> TFTP Server IP address, path and file name for the server containing the new image.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/mgsw-28240f/user-s-manual-catalan-english-french-dutch/page-337.html>PAGE 337</a></h6><p>Command Guide dhcp Dhcp commands retry Restart the DHCP query process interface vlan Interface Vlan interface <vlan_id> Vlan ID Default: None Usage Guide: To do DHCP renew for specific VLAN Example: To do DHCP renew for specific VLAN (6) Switch # ip dhcp retry interface vlan 6 4.15 logout 4.15.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/mgsw-28240f/user-s-manual-catalan-english-french-dutch/page-338.html>PAGE 338</a></h6><p>Command Guide 4.16 more 4.16.1 more Command: more <path> more Display file <path> File in FLASH or on TFTP server Default: None Usage Guide: To view the file Example: To view the file (222) Switch # copy running-config flash:222 Building configuration... % Saving 2038 bytes to flash:222 Switch # more flash:222 hostname Switch username admin privilege 15 password none ! vlan 1 ! vlan 5 ! ! ! 4.17 no 4.17.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/mgsw-28240f/user-s-manual-catalan-english-french-dutch/page-339.html>PAGE 339</a></h6><p>Command Guide no no Negate a command or set its defaults Default: N/A Usage Guide: To default the function Example: To disable the function (erps 1 command force port0) Switch# no erps 1 command force port0 4.18 ping 4.18.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/mgsw-28240f/user-s-manual-catalan-english-french-dutch/page-340.html>PAGE 340</a></h6><p>Command Guide 64 bytes from 192.168.0.78: icmp_seq=1, time=0ms 64 bytes from 192.168.0.78: icmp_seq=2, time=0ms 64 bytes from 192.168.0.78: icmp_seq=3, time=0ms 64 bytes from 192.168.0.78: icmp_seq=4, time=0ms Sent 5 packets, received 5 OK, 0 bad 4.18.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/mgsw-28240f/user-s-manual-catalan-english-french-dutch/page-341.html>PAGE 341</a></h6><p>Command Guide 4.19 reload 4.19.1 reload cold Command: reload cold reload Reload system cold Reload cold. Default: N/A Usage Guide: To restart the device. Example: To restart the device. Switch# reload cold 4.19.2 reload defaults Command: reload defaults [ keep-ip ] reload Reload system defaults keep-ip Reload defaults without rebooting. Attempt to keep VLAN1 IP setup. Default: N/A Usage Guide: To store the device factory default settings. Example: To store the device factory default settings.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/mgsw-28240f/user-s-manual-catalan-english-french-dutch/page-342.html>PAGE 342</a></h6><p>Command Guide 4.20 send 4.20.1 send Command: send { * | console 0 | vty <vty_list> } <message> reload Reload system * All tty lines console vty Primary terminal line Virtual terminal Default: N/A Usage Guide: To send message for command line user. Example: To send message ( hi, I will upgrade the firmware, OK? ) for command line user (All). Switch # send * 1 Enter TEXT message. End with the character '1'.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/mgsw-28240f/user-s-manual-catalan-english-french-dutch/page-343.html>PAGE 343</a></h6><p>Command Guide 4.21 show 4.21.1 show aaa Command: show aaa show Show running system information aaa Login methods Default: N/A Usage Guide: To display the AAA services. Example: To display the AAA services Switch # show aaa console : local telnet ssh : local : local http : local 4.21.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/mgsw-28240f/user-s-manual-catalan-english-french-dutch/page-344.html>PAGE 344</a></h6><p>Command Guide Switch # show access management statistics Access Management Statistics: ----------------------------HTTP Receive: 0 Allow: 0 Discard: 0 HTTPS Receive: 0 Allow: 0 Discard: 0 SNMP Receive: 0 Allow: 0 Discard: 0 TELNET Receive: 0 Allow: 0 Discard: 0 SSH Receive: 0 Allow: 0 Discard: 0 4.21.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/mgsw-28240f/user-s-manual-catalan-english-french-dutch/page-345.html>PAGE 345</a></h6><p>Command Guide Switch access-list rate limiter ID 6 is 1 pps Switch access-list rate limiter ID 7 is 1 pps Switch access-list rate limiter ID 8 is 1 pps Switch access-list rate limiter ID 9 is 1 pps Switch access-list rate limiter ID 10 is 1 pps Switch access-list rate limiter ID 11 is 1 pps Switch access-list rate limiter ID 12 is 1 pps Switch access-list rate limiter ID 13 is 1 pps Switch access-list rate limiter ID 14 is 1 pps Switch access-list rate limiter ID 15 is 1 pps Switch access-list rate limiter</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/mgsw-28240f/user-s-manual-catalan-english-french-dutch/page-346.html>PAGE 346</a></h6><p>Command Guide Usage Guide: To display the ACL Statistics, Rate Limiter List, ACE Statistics. Example: To display the ACL Statistics, Rate Limiter List, ACE Statistics for interface GigabitEthernet 1/1.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/mgsw-28240f/user-s-manual-catalan-english-french-dutch/page-347.html>PAGE 347</a></h6><p>Command Guide 4.21.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/mgsw-28240f/user-s-manual-catalan-english-french-dutch/page-348.html>PAGE 348</a></h6><p>Command Guide User ID ---- -- Frame ----- Action Rate L. CPU Counter Conflict ------ -------- ------ ------- -------- DHCP 1 UDP Deny Disabled Yes 0 No DHCP 2 UDP Deny Disabled Yes 0 No PTP 1 EType Deny Disabled Yes 0 No PTP 2 EType Deny Disabled Yes 0 No Switch 1 access-list ace number: 4 4.21.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/mgsw-28240f/user-s-manual-catalan-english-french-dutch/page-349.html>PAGE 349</a></h6><p>Command Guide Default: N/A Usage Guide: To display the Aggregation mode status. Example: To display the Aggregation mode status. Switch # show aggregation mode Aggregation Mode: SMAC : Enabled DMAC : Disabled IP : Enabled Port : Enabled 4.21.8 show clock Command: show clock show Show running system information clock Configure time-of-day clock Default: N/A Usage Guide: To display the system time. Example: To display the system time.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/mgsw-28240f/user-s-manual-catalan-english-french-dutch/page-350.html>PAGE 350</a></h6><p>Command Guide 4.21.9 show clock detail Command: show clock detail show Show running system information clock Configure time-of-day clock detail Display detailed information Default: N/A Usage Guide: To display the detailed system time. Example: To display the detailed system time. Switch # show clock detail System Time : 1970-01-01T00:29:25+00:00 Timezone : Timezone Offset : 0 ( 0 minutes) Timezone Acronym : Daylight Saving Time Mode : Disabled.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/mgsw-28240f/user-s-manual-catalan-english-french-dutch/page-351.html>PAGE 351</a></h6><p>Command Guide 4.21.10 show dot1x statistics Command: show dot1x statistics show Show running system information dot1x IEEE Standard for port-based Network Access Control statistics all Shows statistics for either eapol or radius Show all dot1x statistics eapol Show EAPOL statistics radius Show Backend Server statistics interface Interface Default: N/A Usage Guide: To display the IEEE 802.1X statistics. Example: To display the All of IEEE 802.1X statistics for interface GigabitEthernet 1/1.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/mgsw-28240f/user-s-manual-catalan-english-french-dutch/page-352.html>PAGE 352</a></h6><p>Command Guide 4.21.11 show dot1x status Command: show dot1x status [ interface ( <port_type> [ <v_port_type_list> ] ) ] [ brief ] show Show running system information dot1x IEEE Standard for port-based Network Access Control status Shows dot1x status, such as admin state, port state and last source. interface Interface brief Show status in a brief format Default: N/A Usage Guide: To display the IEEE 802.1X status. Example: To display the All of IEEE 802.1X status for brief.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/mgsw-28240f/user-s-manual-catalan-english-french-dutch/page-353.html>PAGE 353</a></h6><p>Command Guide 4.21.12 show eps Command: show eps [ <inst> ] [ detail ] show Show running system information eps Ethernet Protection Switching <inst : range_list> detail The range of EPS instances Show detailed state including configuration information Default: N/A Usage Guide: To display the EPS instance information. Example: To display the EPS instance 1 detailed information.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/mgsw-28240f/user-s-manual-catalan-english-french-dutch/page-354.html>PAGE 354</a></h6><p>Command Guide 4.21.13 show erps Command: show erps [ <groups> ] [ detail | statistics ] show Show running system information erps Ethernet Ring Protection Switching <groups> Zero or more ERPS group numbers detail Show detailed information statistics Show statistics Default: N/A Usage Guide: To display the ERPS group information. Example: To display the ERPS group 1 detailed information.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/mgsw-28240f/user-s-manual-catalan-english-french-dutch/page-355.html>PAGE 355</a></h6><p>Command Guide Port 1 Block Status R-APS Transmission :BLOCKED :STOPPED R-APS Port 0 Reception :NONE R-APS Port 1 Reception :NONE FOP Alarm :OFF 4.21.14 show evc Command: show evc { [ <evc_id> | all ] } [ ece [ <ece_id> ] ] show Show running system information evc Ethernet Virtual Connections <evcid : 1-4096> EVC identifier all Process all EVCs ece EVC Control Entry <eceid : 1-4096> ECE identifier Default: N/A Usage Guide: To display the EVC status.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/mgsw-28240f/user-s-manual-catalan-english-french-dutch/page-356.html>PAGE 356</a></h6><p>Command Guide 4.21.15 show evc statistics Command: show green-ethernet [ interface ( <port_type> [ <port_list> ] ) ] show Show running system information green-ethernet Green ethernet (Power reduction) Default: N/A Usage Guide: To display the EVC statistics. Example: To display the EVC Red Frames statistics for all. Switch # show evc statistics all red EVC ID ------ Interface ----------------------- Rx Red Frames -------------------- 1 GigabitEthernet 1/1 0 1 GigabitEthernet 1/2 0 4.21.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/mgsw-28240f/user-s-manual-catalan-english-french-dutch/page-357.html>PAGE 357</a></h6><p>Command Guide 4.21.17 show green-ethernet energy-detect Command: show green-ethernet energy-detect [ interface ( <port_type> [ <port_list> ] ) ] show Show running system information green-ethernet energy-detect interface Green ethernet (Power reduction) Shows green ethernet energy-detect status for a specific port or ports. Shows green ethernet status for a specific port or ports. Default: N/A Usage Guide: To display the energy-detect of Green Ethernet.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/mgsw-28240f/user-s-manual-catalan-english-french-dutch/page-358.html>PAGE 358</a></h6><p>Command Guide 4.21.19 show history Command: show history show Show running system information history Display the session command history Default: N/A Usage Guide: To display the command history. Example: To display the command history.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/mgsw-28240f/user-s-manual-catalan-english-french-dutch/page-359.html>PAGE 359</a></h6><p>Command Guide Example: To display the SFP Transceiver information for interface GigabitEthernet 1/1. Switch # show interface GigabitEthernet 1/1 capabilities GigabitEthernet 1/1 Capabilities: SFP Type: None SFP Vendor name: SFP Vendor PN: SFP Vendor revision: 4.21.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/mgsw-28240f/user-s-manual-catalan-english-french-dutch/page-360.html>PAGE 360</a></h6><p>Command Guide 4.21.22 show interface <port_type> <port_type_list> status Command: show interface <port_type> <port_type_list> status show Show running system information interface Interface status and configuration status Display status Default: N/A Usage Guide: To display the port status. Example: To display the port status for interface GigabitEthernet 1/1.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/mgsw-28240f/user-s-manual-catalan-english-french-dutch/page-361.html>PAGE 361</a></h6><p>Command Guide Switch # show interface GigabitEthernet 1/1 switchport Name: GigabitEthernet 1/1 Administrative mode: access Access Mode VLAN: 1 Trunk Native Mode VLAN: 1 Administrative Native VLAN tagging: disabled Allowed VLANs: 1-4095 Hybrid port configuration ------------------------Port Type: C-Port Acceptable Frame Type: All Ingress filter: Disabled Egress tagging: All except-native Hybrid Native Mode VLAN: 1 Hybrid VLANs Enabled: 1-4095 4.21.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/mgsw-28240f/user-s-manual-catalan-english-french-dutch/page-362.html>PAGE 362</a></h6><p>Command Guide ------ ------ ------ OK 3 OK ------3 4.21.25 show interface <port_type> <port_type_list> veriphy Command: show interface <port_type> <port_type_list> veriphy show Show running system information interface Interface status and configuration veriphy Run cable diagnostics and show result. Default: N/A Usage Guide: To display the result of Cable Diagnostics. Example: To display the result of Cable Diagnostics for interface GigabitEthernet 1/1.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/mgsw-28240f/user-s-manual-catalan-english-french-dutch/page-363.html>PAGE 363</a></h6><p>Command Guide Default: N/A Usage Guide: To display the MAC address and IP address of specific VLAN. Example: To display the MAC address and IP address for all VLANs. Switch # show interface vlan VLAN1 LINK: 00-30-4F-00-99-00 Mtu:1500 <up broadcast running multicast> IPv4: 192.168.0.100/24 192.168.0.255 IPv6: fe80:2::201:c1ff:fe00:9900/64 <anycast tentative autoconf> 4.21.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/mgsw-28240f/user-s-manual-catalan-english-french-dutch/page-364.html>PAGE 364</a></h6><p>Command Guide 4.21.28 show ip arp inspection Command: show ip arp inspection show ip arp Show running system information Internet Protocol Address Resolution Protocol inspection ARP inspection Default: N/A Usage Guide: To display the ARP Inspection Configuration. Example: To display the ARP Inspection Configuration.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/mgsw-28240f/user-s-manual-catalan-english-french-dutch/page-365.html>PAGE 365</a></h6><p>Command Guide Example: To display the ARP Inspection Configuration. Switch # show ip arp inspection ARP Inspection Mode : disabled Port Port Mode Check VLAN Log Type ---- --------- ---------- -------- GigabitEthernet 1/1 disabled disabled NONE GigabitEthernet 1/2 disabled disabled NONE 4.21.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/mgsw-28240f/user-s-manual-catalan-english-french-dutch/page-366.html>PAGE 366</a></h6><p>Command Guide 4.21.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/mgsw-28240f/user-s-manual-catalan-english-french-dutch/page-367.html>PAGE 367</a></h6><p>Command Guide Rx Release: 0 Tx Release: 0 Rx Inform: 0 Tx Inform: 0 Rx Lease Query: 0 Tx Lease Query: 0 Rx Lease Unassigned: 0 Tx Lease Unassigned: 0 Rx Lease Unknown: 0 Tx Lease Unknown: 0 Rx Lease Active: 0 Tx Lease Active: 0 Rx Lease Active: 0 Tx Lease Active: 0 Rx Discarded checksum error: 0 4.21.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/mgsw-28240f/user-s-manual-catalan-english-french-dutch/page-368.html>PAGE 368</a></h6><p>Command Guide 4.21.33 show ip dhcp pool Command: show ip dhcp pool [ <pool_name> ] show ip Show running system information Internet Protocol dhcp Dynamic Host Configuration Protocol pool DHCP pools information Default: N/A Usage Guide: To display the DHCP pools information. Example: To display the DHCP pools information. Switch # show ip dhcp pool Pool Name: test ---------------------------------------------Type is network IP is 192.168.1.100 Subnet mask is 255.255.255.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/mgsw-28240f/user-s-manual-catalan-english-french-dutch/page-369.html>PAGE 369</a></h6><p>Command Guide 4.21.34 show ip dhcp relay Command: show ip dhcp relay [ statistics ] show Show running system information ip Internet Protocol dhcp Dynamic Host Configuration Protocol relay DHCP relay agent configuration statistics Traffic statistics Default: N/A Usage Guide: To display the DHCP relay information. Example: To display the DHCP relay information. Switch # show ip dhcp relay Switch DHCP relay mode is enabled Switch DHCP relay server address is 192.168.0.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/mgsw-28240f/user-s-manual-catalan-english-french-dutch/page-370.html>PAGE 370</a></h6><p>Command Guide Switch # show ip dhcp server DHCP server is globally disabled. All VLANs are disabled. 4.21.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/mgsw-28240f/user-s-manual-catalan-english-french-dutch/page-371.html>PAGE 371</a></h6><p>Command Guide 4.21.37 show ip dhcp server declined-ip (GG) Command: show ip dhcp server declined-ip show ip Show running system information Internet Protocol dhcp Dynamic Host Configuration Protocol server DHCP server information declined-ip Declined IP address Default: N/A Usage Guide: To display the DHCP Decline information. Example: To display the DHCP Decline information. Switch # show ip dhcp server declined-ip 4.21.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/mgsw-28240f/user-s-manual-catalan-english-french-dutch/page-372.html>PAGE 372</a></h6><p>Command Guide Database Counters ========================= POOL 2 Excluded IP 1 Declined IP 0 ========================= Binding Counters ========================= Automatic Manual Expired 0 0 0 ========================= Message Received Counters ========================= DISCOVER 0 REQUEST 0 DECLINE 0 RELEASE 0 INFORM 0 ========================= Message Sent Counters ========================= OFFER 0 ACK 0 NAK 0 ========================= 4.21.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/mgsw-28240f/user-s-manual-catalan-english-french-dutch/page-373.html>PAGE 373</a></h6><p>Command Guide Default: N/A Usage Guide: To display the DHCP Snooping configuration. Example: To display the DHCP Snooping configuration for GigabitEthernet 1/1. Switch # show ip dhcp snooping interface GigabitEthernet 1/1 GigabitEthernet 1/1 untrusted 4.21.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/mgsw-28240f/user-s-manual-catalan-english-french-dutch/page-374.html>PAGE 374</a></h6><p>Command Guide 4.21.41 show ip http server secure status Command: show ip http server secure status show ip Show running system information Internet Protocol http Hypertext Transfer Protocol server HTTP web server secure Secure status Status Default: N/A Usage Guide: To display the DHCP Snooping table. Example: To display the DHCP Snooping table. Switch # show ip http server secure status Switch secure HTTP web server is disabled Switch secure HTTP web redirection is disabled 4.21.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/mgsw-28240f/user-s-manual-catalan-english-french-dutch/page-375.html>PAGE 375</a></h6><p>Command Guide Usage Guide: To display the IGMP Snooping information. Example: To display the IGMP Snooping information (Detail). Switch # show ip igmp snooping detail IGMP Snooping is disabled to stop snooping IGMP control plane. Multicast streams destined to unregistered IGMP groups will be flooding. 4.21.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/mgsw-28240f/user-s-manual-catalan-english-french-dutch/page-376.html>PAGE 376</a></h6><p>Command Guide 4.21.44 show ip interface brief Command: show ip interface brief show Show running system information ip Internet Protocol interface brief IP interface status and configuration Brief IP interface status Default: N/A Usage Guide: To display the IP interface status. Example: To display the IP interface status. Switch # show ip interface brief Vlan Address Method Status ---- -------------------- -------- -----1 192.168.0.100/24 Manual UP 4.21.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/mgsw-28240f/user-s-manual-catalan-english-french-dutch/page-377.html>PAGE 377</a></h6><p>Command Guide 4.21.46 show ip route Command: show ip route show ip Show running system information Internet Protocol route Display the current ip routing table Default: N/A Usage Guide: To display the IP Routing table. Example: To display the IP Routing table. Switch # show ip route 11.11.11.0/24 via 192.168.0.14 <up gateway hw_rt> 127.0.0.1/32 via 127.0.0.1 <up host> 192.168.0.0/24 via VLAN1 <up hw_rt> 224.0.0.0/4 via 127.0.0.1 <up> 4.21.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/mgsw-28240f/user-s-manual-catalan-english-french-dutch/page-378.html>PAGE 378</a></h6><p>Command Guide Example: To display the Static IP Source Guard Table. Switch # show ip source binding interface GigabitEthernet 1/1 Type Port ---- ---- Static VLAN IP Address GigabitEthernet 1/1 ---1 ---------192.168.0.22 4.21.48 show ip ssh Command: show ip ssh show ip Show running system information Internet Protocol ssh Secure Shell Default: N/A Usage Guide: To display the SSH Management status. Example: To display the SSH Management status. Switch # show ip ssh Switch SSH is enabled 4.21.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/mgsw-28240f/user-s-manual-catalan-english-french-dutch/page-379.html>PAGE 379</a></h6><p>Command Guide Usage Guide: To display the IP statistics. Example: To display the IP statistics.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/mgsw-28240f/user-s-manual-catalan-english-french-dutch/page-380.html>PAGE 380</a></h6><p>Command Guide Rcvd: 2618 Messages, 0 Error Sent: 2618 Messages, 0 Error ICMP message statistics: IPv4 ICMP Message: Echo Reply Rcvd: 0 Packet Sent: 2618 Packets IPv4 ICMP Message: Echo Rcvd: 2618 Packets Sent: 0 Packet 4.21.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/mgsw-28240f/user-s-manual-catalan-english-french-dutch/page-381.html>PAGE 381</a></h6><p>Command Guide 4.21.51 show ipmc profile Command: show ipmc profile [ <profile_name> ] [ detail ] show Show running system information ipmc IPv4/IPv6 multicast configuration profile IPMC profile configuration <profilename : word16> detail Profile name Detail information of a profile Default: N/A Usage Guide: To display the IP Multicast Profile. Example: To display the IP Multicast Profile. Switch # show ipmc profile IPMC Profile is now enabled to start filtering.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/mgsw-28240f/user-s-manual-catalan-english-french-dutch/page-382.html>PAGE 382</a></h6><p>Command Guide Switch # show ipmc range Range Name :1 Start Address: 224.24.24.24 End Address : 224.24.24.25 4.21.53 show ipv6 interface Command: show ipv6 interface [ vlan <vlan_list> { brief | statistics } ] show Show running system information ipv6 vlan IPv6 configuration commands VLAN of IPv6 interface brief Brief summary of IPv6 status and configuration statistics Traffic statistics Default: N/A Usage Guide: To display the IPv6 configuration. Example: To display the IPv6 configuration.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/mgsw-28240f/user-s-manual-catalan-english-french-dutch/page-383.html>PAGE 383</a></h6><p>Command Guide 0 no route, 0 truncated, 0 discarded Sent: 17 total in 1104 bytes 17 generated, 0 forwarded 0 discarded Frags: 0 reassemble (0 reassembled, 0 couldn't reassemble) 0 fragment (0 fragmented, 0 couldn't fragment) 0 fragment created Mcast: 3 received in 168 bytes 17 sent in 1104 bytes Bcast: 0 received, 0 sent 4.21.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/mgsw-28240f/user-s-manual-catalan-english-french-dutch/page-384.html>PAGE 384</a></h6><p>Command Guide 4.21.55 show ipv6 mld snooping mrouter Command: show ip igmp snooping mrouter [ detail ] show Show running system information ipv6 IPv6 configuration commands mld Multicast Listener Discovery snooping mrouter Snooping MLD Multicast router port status in MLD detail Detail running information/statistics of MLD snooping Default: N/A Usage Guide: To display the MLD Router Port information. Example: To display the MLD Router Port information.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/mgsw-28240f/user-s-manual-catalan-english-french-dutch/page-385.html>PAGE 385</a></h6><p>Command Guide Example: To display the IPv6 neighbor information. Switch # show ipv6 neighbor 2001::7766 via VLAN1: 00-30-4F-00-99-00 Permanent/REACHABLE fe80::201:c1ff:fe00:9900 via VLAN1: 00-30-4F-00-99-00 Permanent/REACHABLE 4.21.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/mgsw-28240f/user-s-manual-catalan-english-french-dutch/page-386.html>PAGE 386</a></h6><p>Command Guide 4.21.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/mgsw-28240f/user-s-manual-catalan-english-french-dutch/page-387.html>PAGE 387</a></h6><p>Command Guide IP interface statistics: IPv6 Statistics on Interface VLAN: 1 Rcvd: 12 total in 1032 bytes 3 local destination, 0 forwarding 0 header error, 0 address error, 0 unknown protocol 0 no route, 0 truncated, 9 discarded Sent: 17 total in 1104 bytes 17 generated, 0 forwarded 0 discarded Frags: 0 reassemble (0 reassembled, 0 couldn't reassemble) 0 fragment (0 fragmented, 0 couldn't fragment) 0 fragment created Mcast: 12 received in 1032 bytes 17 sent in 1104 bytes Bcast: 0 received, 0 sent IPv6 IC</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/mgsw-28240f/user-s-manual-catalan-english-french-dutch/page-388.html>PAGE 388</a></h6><p>Command Guide 4.21.59 show lacp Command: show lacp { internal | statistics | system-id | neighbour } show Show running system information lacp LACP configuration/status internal Internal LACP configuration neighbour statistics Neighbour LACP status Internal LACP statistics system-id LACP system id Default: N/A Usage Guide: To display the LACP mode information. Example: To display the LACP mode information.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/mgsw-28240f/user-s-manual-catalan-english-french-dutch/page-389.html>PAGE 389</a></h6><p>Command Guide Switch # show line alive Line is con 0. * You are at this line now. Alive from Console. Default privileged level is 2. Command line editing is enabled Display EXEC banner is enabled. Display Day banner is enabled. Terminal width is 80. length is 24. history size is 32. exec-timeout is 10 min 0 second. Current session privilege is 15. Elapsed time is 0 day 0 hour 17 min 20 sec. Idle time is 0 day 0 hour 0 min 0 sec. 4.21.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/mgsw-28240f/user-s-manual-catalan-english-french-dutch/page-390.html>PAGE 390</a></h6><p>Command Guide 4.21.62 show lldp med remote-device Command: show lldp med remote-device [ interface ( <port_type> [ <port_list> ] ) ] show Show running system information lldp Display LLDP neighbors information med Display LLDP-MED neighbors information remote-device interface Display remote device LLDP-MED neighbors information Interface to display Default: N/A Usage Guide: To display the LLDP-MED entries information. Example: To display the LLDP-MED entries information.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/mgsw-28240f/user-s-manual-catalan-english-french-dutch/page-391.html>PAGE 391</a></h6><p>Command Guide 4.21.64 show lldp statistics Command: show lldp statistics [ interface ( <port_type> [ <port_type_list> ] ) ] show Show running system information lldp Display LLDP neighbors information statistics Display LLDP statistics information interface Interface to display Default: N/A Usage Guide: To display the LLDP statistics information. Example: To display the LLDP statistics information for GigabitEthernet 1/1.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/mgsw-28240f/user-s-manual-catalan-english-french-dutch/page-392.html>PAGE 392</a></h6><p>Command Guide Usage Guide: To display the Syslog information. Example: To display the Syslog information with Log ID 235861. Switch # show logging 235861 Switch : 1 ID : 235861 Level : Warning Time : 1970-01-01T13:33:57+00:00 Message: Loop Detected: Port 5 shut down 4.21.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/mgsw-28240f/user-s-manual-catalan-english-french-dutch/page-393.html>PAGE 393</a></h6><p>Command Guide Transmit mode is enabled. No loop. The number of loops is 12390. Time of last loop is at 1970-01-01T14:58:28+00:00 Status is down. 4.21.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/mgsw-28240f/user-s-manual-catalan-english-french-dutch/page-394.html>PAGE 394</a></h6><p>Command Guide 4.21.68 show mep Command: show mep [ <instance> ] [ peer | cc | lm | dm | lt | lb | tst | aps | client | ais | lck ] [ detail ] show Show running system information mep Maintenance Entity Point <instance> The range of MEP instances ais Show AIS state aps Show APS state cc Show CC state client Show Client state detail Show detailed state including configuration information.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/mgsw-28240f/user-s-manual-catalan-english-french-dutch/page-395.html>PAGE 395</a></h6><p>Command Guide 4.21.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/mgsw-28240f/user-s-manual-catalan-english-french-dutch/page-396.html>PAGE 396</a></h6><p>Command Guide 4.21.70 show network-clock Command: show network-clock show Show running system information network-clock Show selector state Default: N/A Usage Guide: To display the SyncE information. Example: To display the SyncE information. Switch # show network-clock Selector State is: Free Run Alarm State is: Clk: 1 2 LOCS: FALSE FALSE SSM: FALSE FALSE WTR: FALSE FALSE LOL: DHOLD: FALSE TRUE SSM State is: Interface GigabitEthernet 1/1 Tx SSM QL_NONE Rx SSM Mode QL_LINK Master 4.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/mgsw-28240f/user-s-manual-catalan-english-french-dutch/page-397.html>PAGE 397</a></h6><p>Command Guide Default: N/A Usage Guide: To display the NTP Server information. Example: To display the NTP Server information. Switch # show ntp status NTP Mode : enabled Idx --1 Server IP host address (a.b.c.d) or a host name string -----------------------------------------------------192.168.0.44 2 3 4 5 4.21.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/mgsw-28240f/user-s-manual-catalan-english-french-dutch/page-398.html>PAGE 398</a></h6><p>Command Guide 4.21.73 show platform phy failover Command: show platform phy failover show Show running system information platform phy Platform specific information PHYs' information failover Failover status Default: N/A Usage Guide: To display the PHY failover status. Example: To display the PHY failover status. Switch # show platform phy failover Port Active Channel Broadcast After reset ------ ------- --------- ------------ ---- 4.21.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/mgsw-28240f/user-s-manual-catalan-english-french-dutch/page-399.html>PAGE 399</a></h6><p>Command Guide Switch # show platform phy id interface GigabitEthernet 1/1 Port Channel ---- API Base ------- 1 0 -------0 (1g) Phy Id Phy Rev. ------8634 -----0 4.21.75 show platform phy status Command: show platform phy status [ interface ( <port_type> [ <v_port_type_list> ] ) ] show Show running system information platform phy Platform specific information PHYs' information status status interface Search by port Default: N/A Usage Guide: To display the PHY status.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/mgsw-28240f/user-s-manual-catalan-english-french-dutch/page-400.html>PAGE 400</a></h6><p>Command Guide Default: N/A Usage Guide: To display the MAC Addresses of Port Security. Example: To display the MAC Addresses of Port Security. Switch # show port-security port interface GigabitEthernet 1/1 GigabitEthernet 1/1 ------------------MAC Address VID State ----------------- ---- ---------- Added Age/Hold Time ------------------------- ------------- <none> 4.21.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/mgsw-28240f/user-s-manual-catalan-english-french-dutch/page-401.html>PAGE 401</a></h6><p>Command Guide 4.21.78 show privilege Command: show privilege show Show running system information privilege Display command privilege Default: N/A Usage Guide: To display the Privilege information. Example: To display the Privilege information. Switch # show privilege 4.21.79 show pvlan Command: show pvlan [ <pvlan_list> ] show Show running system information pvlan PVLAN configuration Default: N/A Usage Guide: To display the Private VLAN membership configuration.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/mgsw-28240f/user-s-manual-catalan-english-french-dutch/page-402.html>PAGE 402</a></h6><p>Command Guide 4.21.80 show pvlan isolation Command: show pvlan isolation [ interface ( <port_type> [ <port_list> ] ) ] show Show running system information pvlan PVLAN configuration isolation show isolation configuration interface Search by port Default: N/A Usage Guide: To display the port isolation configuration. Example: To display the port isolation configuration.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/mgsw-28240f/user-s-manual-catalan-english-french-dutch/page-403.html>PAGE 403</a></h6><p>Command Guide qce QoS Control Entry <qce> QCE ID wred Weighted Random Early Discard Default: N/A Usage Guide: To display the QoS configuration. Example: To display the QoS configuration for GigabitEthernet 1/1.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/mgsw-28240f/user-s-manual-catalan-english-french-dutch/page-404.html>PAGE 404</a></h6><p>Command Guide qos queue-policer queue 6 mode: disabled, rate: 500 kbps qos queue-policer queue 7 mode: disabled, rate: 500 kbps qos shaper mode: disabled, rate: 500 kbps qos queue-shaper queue 0 mode: disabled, rate: 500 kbps, excess: disabled qos queue-shaper queue 1 mode: disabled, rate: 500 kbps, excess: disabled qos queue-shaper queue 2 mode: disabled, rate: 500 kbps, excess: disabled qos queue-shaper queue 3 mode: disabled, rate: 500 kbps, excess: disabled qos queue-shaper queue 4 mode: disabled, rate:</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/mgsw-28240f/user-s-manual-catalan-english-french-dutch/page-405.html>PAGE 405</a></h6><p>Command Guide 4.21.82 show radius-server Command: show radius-server [ statistics ] show Show running system information radius-server statistics RADIUS configuration RADIUS statistics Default: N/A Usage Guide: To display the RADIUS Server configuration. Example: To display the RADIUS Server configuration.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/mgsw-28240f/user-s-manual-catalan-english-french-dutch/page-406.html>PAGE 406</a></h6><p>Command Guide Switch # show rmon alarm 1 Alarm ID : 1 ---------------Interval : 30 Variable : .1.3.6.1.2.1.2.2.1.20.1 SampleType Value : deltaValue :0 Startup : risingOrFallingAlarm RisingThrld :2 FallingThrld :1 RisingEventIndex : 2 FallingEventIndex : 1 4.21.84 show rmon event Command: show rmon event [ <id_list> ] show Show running system information rmon RMON statistics event Display the RMON event table Default: N/A Usage Guide: To display the RMON Event configuration.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/mgsw-28240f/user-s-manual-catalan-english-french-dutch/page-407.html>PAGE 407</a></h6><p>Command Guide 4.21.85 show rmon history Command: show rmon history [ <id_list> ] show Show running system information rmon RMON statistics history Display the RMON history table Default: N/A Usage Guide: To display the RMON History configuration. Example: To display the RMON History ID 1 configuration. Switch # show rmon history 1 History ID : 1 -----------------Data Source : .1.3.6.1.2.1.2.2.1.1.5 Data Bucket Request : 50 Data Bucket Granted : 50 Data Interval : 1800 4.21.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/mgsw-28240f/user-s-manual-catalan-english-french-dutch/page-408.html>PAGE 408</a></h6><p>Command Guide Switch # show rmon statistics 1 Statistics ID : 1 --------------------Data Source : .1.3.6.1.2.1.2.2.1.1.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/mgsw-28240f/user-s-manual-catalan-english-french-dutch/page-409.html>PAGE 409</a></h6><p>Command Guide 'port' 'port-security' 'ptp' 'pvlan' 'qos' 'rmon' 'snmp' 'source-guard' 'ssh' 'upnp' 'user' 'vlan' 'voice-vlan' 'web-privilege-group-level' all-defaults Include most/all default values interface Show specific interface(s) vlan VLAN line Show line settings console vty Console VTY Default: N/A Usage Guide: To display the running-config. Example 1: To display the running-config. Switch # show running-config Building configuration...</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/mgsw-28240f/user-s-manual-catalan-english-french-dutch/page-410.html>PAGE 410</a></h6><p>Command Guide 4.21.88 show snmp Command: show snmp show Show running system information snmp Display SNMP configurations Default: N/A Usage Guide: To display the SNMP information. Example: To display the SNMP information Switch # show snmp SNMP Configuration SNMP Mode : enabled SNMP Version : 2c Read Community : public Write Community : private Trap Mode : disabled Trap Version :1 SNMPv3 Communities Table: Community Source IP : public : 0.0.0.0 Source Mask : 0.0.0.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/mgsw-28240f/user-s-manual-catalan-english-french-dutch/page-411.html>PAGE 411</a></h6><p>Command Guide SNMPv3 Groups Table; Security Model : v1 Security Name : public Group Name : default_ro_group Security Model : v1 Security Name : private Group Name : default_rw_group Security Model : v2c Security Name : public Group Name : default_ro_group Security Model : v2c Security Name : private Group Name : default_rw_group Security Model : v3 Security Name : default_user Group Name : default_rw_group SNMPv3 Accesses Table: Group Name : default_ro_group Security Model Security Le</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/mgsw-28240f/user-s-manual-catalan-english-french-dutch/page-412.html>PAGE 412</a></h6><p>Command Guide 4.21.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/mgsw-28240f/user-s-manual-catalan-english-french-dutch/page-413.html>PAGE 413</a></h6><p>Command Guide 4.21.90 show snmp community v3 Command: show snmp community v3 [ <community> ] show Show running system information snmp Display SNMP configurations community v3 Community SNMPv3 <community : word127> Specify community name Default: N/A Usage Guide: To display the SNMPv3 Community information. Example: To display the SNMPv3 Community information Switch # show snmp community v3 Community Source IP : public : 0.0.0.0 Source Mask : 0.0.0.0 Community Source IP : private : 0.0.0.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/mgsw-28240f/user-s-manual-catalan-english-french-dutch/page-414.html>PAGE 414</a></h6><p>Command Guide Default: N/A Usage Guide: To display the SNMP Host information. Example: To display the SNMP Host information Switch # show snmp host Trap Global Mode: Disabled 4.21.92 show snmp mib context Command: show snmp mib context show Show running system information snmp Display SNMP configurations mib MIB(Management Information Base) context MIB context Default: N/A Usage Guide: To display the SNMP MIB contexts. Example: To display the SNMP MIB contexts.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/mgsw-28240f/user-s-manual-catalan-english-french-dutch/page-415.html>PAGE 415</a></h6><p>Command Guide - ieee8021MstpMib (.1.3.111.2.802.1.1.6) IEEE8021-PAE-MIB : - ieee8021paeMIB (.1.0.8802.1.1.1.1) IEEE8023-LAG-MIB : - lagMIBObjects (.1.2.840.10006.300.43.1) IF-MIB : - ifMIB (.1.3.6.1.2.1.31) IP-FORWARD-MIB : - ipForward (.1.3.6.1.2.1.4.24) IP-MIB : - ipv4InterfaceTable (.1.3.6.1.2.1.4.28) - ipv6InterfaceTable (.1.3.6.1.2.1.4.30) - ipTrafficStats (.1.3.6.1.2.1.4.31) - ipAddressTable (.1.3.6.1.2.1.4.34) - ipNetToPhysicalTable (.1.3.6.1.2.1.4.35) - ipv6ScopeZoneIndexTable (.1.3.6.1.2.1.4.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/mgsw-28240f/user-s-manual-catalan-english-french-dutch/page-416.html>PAGE 416</a></h6><p>Command Guide - snmp (.1.3.6.1.2.1.5) - tcp (.1.3.6.1.2.1.6) - udp (.1.3.6.1.2.1.7) RMON-MIB : - statistics (.1.3.6.1.2.1.16.1) - history (.1.3.6.1.2.1.16.2) - alarm (.1.3.6.1.2.1.16.3) - event (.1.3.6.1.2.1.16.9) SMON-MIB : - switchRMON (.1.3.6.1.2.1.16.22) SNMP-FRAMEWORK-MIB : - snmpEngine (.1.3.6.1.6.3.10.2.1) SNMP-MPD-MIB : - dot1dTpHCPortTable (.1.3.6.1.2.1.17.4.5) - snmpMPDStats (.1.3.6.1.6.3.11.2.1) SNMP-USER-BASED-SM-MIB : - usmStats (.1.3.6.1.6.3.15.1.1) - usmUserTable (.1.3.6.1.6.3.15.1.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/mgsw-28240f/user-s-manual-catalan-english-french-dutch/page-417.html>PAGE 417</a></h6><p>Command Guide Example: To display the SNMP MIB ifIndex contexts.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/mgsw-28240f/user-s-manual-catalan-english-french-dutch/page-418.html>PAGE 418</a></h6><p>Command Guide 4.21.94 show snmp security-to-group Command: show snmp security-to-group [ { v1 | v2c | v3 } <security_name> ] show Show running system information snmp Display SNMP configurations security-to-group security-to-group configuration v1 v1 security model v2c v2c security model v3 v3 security model <securityname : word32> security group name Default: N/A Usage Guide: To display the SNMP Group information. Example: To display the SNMP Group information.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/mgsw-28240f/user-s-manual-catalan-english-french-dutch/page-419.html>PAGE 419</a></h6><p>Command Guide 4.21.95 show snmp user Command: show snmp user [ <username> <engineid> ] show Show running system information snmp Display SNMP configurations user User <username : word32> <engiedid : word10-32> Security user name Security Engine ID Default: N/A Usage Guide: To display the SNMP User information. Example: To display the SNMP User information.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/mgsw-28240f/user-s-manual-catalan-english-french-dutch/page-420.html>PAGE 420</a></h6><p>Command Guide Example: To display the SNMP viewer information. Switch # show snmp view View Name : default_view OID Subtree : .1 View Type : included 4.21.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/mgsw-28240f/user-s-manual-catalan-english-french-dutch/page-421.html>PAGE 421</a></h6><p>Command Guide Int. PathCost: 0 Max Hops : 20 TC Flag : Steady TC Count :0 TC Last :- Port Port Role --------- -------------- State ---------- --- Pri -------- PathCost ---- --- Edge ------------- 4.21.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/mgsw-28240f/user-s-manual-catalan-english-french-dutch/page-422.html>PAGE 422</a></h6><p>Command Guide 4.21.99 show tacacs-server Command: show tacacs-server show Show running system information tacacs-server TACACS+ configuration Default: N/A Usage Guide: To display the TACACS+ Server configuration. Example: To display the TACACS+ Server configuration. Switch # show tacacs-server Global TACACS+ Server Timeout : 5 seconds Global TACACS+ Server Deadtime : 0 minutes Global TACACS+ Server Key : No hosts configured! 4.21.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/mgsw-28240f/user-s-manual-catalan-english-french-dutch/page-423.html>PAGE 423</a></h6><p>Command Guide Alive from Console. Default privileged level is 2. Command line editing is enabled Display EXEC banner is enabled. Display Day banner is enabled. Terminal width is 80. length is 24. history size is 32. exec-timeout is 10 min 0 second. Current session privilege is 15. Elapsed time is 0 day 1 hour 12 min 15 sec. Idle time is 0 day 0 hour 0 min 0 sec. 4.21.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/mgsw-28240f/user-s-manual-catalan-english-french-dutch/page-424.html>PAGE 424</a></h6><p>Command Guide 4.21.102 show users Command: show users [ myself ] show Show running system information users Display information about terminal lines myself Display information about mine Default: N/A Usage Guide: To display the user status. Example: To display the user status for all. Switch # show users Line is con 0. * You are at this line now. Connection is from Console. User name is admin. Privilege is 15. Elapsed time is 0 day 1 hour 20 min 49 sec. Idle time is 0 day 0 hour 0 min 0 sec.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/mgsw-28240f/user-s-manual-catalan-english-french-dutch/page-425.html>PAGE 425</a></h6><p>Command Guide 4.21.103 show version Command: show version show Show running system information version System hardware and software status Default: N/A Usage Guide: To display the software and system information. Example: To display the software and system information.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/mgsw-28240f/user-s-manual-catalan-english-french-dutch/page-426.html>PAGE 426</a></h6><p>Command Guide 4.21.104 show vlan Command: show vlan [ id <vlan_list> | name <name> | brief ] show Show running system information vlan VLAN status id VLAN status by VLAN id name VLAN status by VLAN name brief VLAN summary information Default: N/A Usage Guide: To display the VLAN information. Example: To display the VLAN information. Switch # show vlan VLAN ---1 Name -------------------------------- Interfaces ---------- default Gi 1/1-25 10G 1/1-4 4.21.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/mgsw-28240f/user-s-manual-catalan-english-french-dutch/page-427.html>PAGE 427</a></h6><p>Command Guide Switch # show vlan ip-subnet VCE ID ------ IP Address --------------- 1 Mask Length ----------- 192.168.78.0 ---- VID Interfaces ---------- 24 5 GigabitEthernet 1/1 4.21.106 show vlan mac Command: show vlan mac [ address <mac_addr> ] show Show running system information vlan VLAN status mac Show VLAN MAC entries address Show a specific MAC entry Default: N/A Usage Guide: To display the MAC-based VLAN information. Example: To display the MAC-based VLAN information.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/mgsw-28240f/user-s-manual-catalan-english-french-dutch/page-428.html>PAGE 428</a></h6><p>Command Guide at Ether Type is AppleTalk ip Ether Type is IP ipx Ether Type is IPX llc LLC-based VLAN status <dsap> DSAP (Range: 0x00 - 0xFF) <ssap> SSAP (Range: 0x00 - 0xFF) snap SNAP-based VLAN status <oui> SNAP OUI (Range 0x000000 - 0XFFFFFF) rfc-1042 SNAP OUI is rfc-1042 snap-8021h <pid> SNAP OUI is 8021h PID (Range: 0x0 - 0xFFFF) Default: N/A Usage Guide: To display the Protocol-based VLAN information. Example: To display the Protocol-based VLAN information.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/mgsw-28240f/user-s-manual-catalan-english-french-dutch/page-429.html>PAGE 429</a></h6><p>Command Guide oui OUI configuration <oui> OUI value Default: N/A Usage Guide: To display the Voice VLAN information. Example: To display the Voice VLAN information for GigabitEthernet 1/1 Switch # show voice vlan interface GigabitEthernet 1/1 GigabitEthernet 1/1 : --------------------GigabitEthernet 1/1 switchport voice vlan mode is auto GigabitEthernet 1/1 switchport voice security is disabled GigabitEthernet 1/1 switchport voice discovery protocol is oui 4.21.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/mgsw-28240f/user-s-manual-catalan-english-french-dutch/page-430.html>PAGE 430</a></h6><p>Command Guide Switch # show web privilege group level Group Name Privilege Level CRO CRW SRO SRW Aggregation 6 10 5 Debug 15 15 15 DHCP 5 10 5 10 Dhcp_Client 5 10 5 10 Diagnostics 5 10 5 10 EPS 5 10 5 10 ERPS 5 10 5 10 ETH_LINK_OAM 5 10 5 10 EVC 5 10 5 10 Green_Ethernet 5 10 5 10 IP2 5 10 5 10 IPMC_Snooping 5 10 5 10 LACP 5 10 5 10 LLDP 5 10 5 10 Loop_Protect 5 10 5 10 MAC_Table 5 10 5 10 Maintenance 15 15 15 MEP 5 10 5</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/mgsw-28240f/user-s-manual-catalan-english-french-dutch/page-431.html>PAGE 431</a></h6><p>Command Guide 4.22 terminal 4.22.1 terminal editing Command: terminal editing terminal editing Set terminal line parameters Enable command line editing Default: Enabled Usage Guide: To enable editing mode for current terminal session. Example: To enable editing mode for current terminal session. Switch # terminal editing 4.22.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/mgsw-28240f/user-s-manual-catalan-english-french-dutch/page-432.html>PAGE 432</a></h6><p>Command Guide 4.22.3 terminal history size Command: terminal history size <history_size> terminal Set terminal line parameters history Control the command history function size Set history buffer size <history_size> Number of history commands, 0 means disable Default: N/A Usage Guide: To configure history buffer side for current terminal session. Example: To configure history buffer side with 20 lines for current terminal session. Switch # terminal history size 20 4.22.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/mgsw-28240f/user-s-manual-catalan-english-french-dutch/page-433.html>PAGE 433</a></h6><p>Command Guide 4.22.5 terminal width Command: terminal width <lines> terminal width Set terminal line parameters Set width of the display terminal <lines:0 or 40-512> Number of characters on a screen line (0 for unlimited width) Default: N/A Usage Guide: To configure width of command display for current terminal session. Example: To configure width of command display with 40 characters per line for current terminal session.</p></li></ul></nav></div></section></section></main><footer class=page-footer><div class="container flex-column py-3 py-sm-4"><div class="row mb-1 mb-sm-2 mb-md-5"><a href=/ class="brand offset-sm-0 col-sm-4 col-md-3 col-lg-2 offset-2 col-8 text-center text-md-start"><img class=logo-small src=/assets/img/brand-large.png alt=Manualshelf></a></div><div class=row><dl class="text-center text-sm-start col-sm-3"><dt class=fw-bold>Who We Are</dt><dd><a class=text-decoration-none href=/about>About Us</a></dd><dd><a class=text-decoration-none href=/company>Company</a></dd><dd><a class=text-decoration-none href=/careers>Careers</a></dd><dd><a class=text-decoration-none href=/terms>Terms & Privacy</a></dd></dl><dl class="text-center text-sm-start col-sm-3"><dt class=fw-bold>Resources</dt><dd><a class=text-decoration-none href=/brands>List of Manufacturers</a></dd><dd><a href=/ class=text-decoration-none>Support</a></dd><dd><a class=text-decoration-none href=/press>For the Press</a></dd><dd><a class=text-decoration-none href=/press#assets>Media assets</a></dd><dd><a class=text-decoration-none href=/faq>FAQ</a></dd></dl><dl class="text-center text-sm-start col-sm-3"><dt class=fw-bold>Get in touch</dt><dd><a class=text-decoration-none href=#>Blog</a></dd><dd><a class=text-decoration-none href=#>Email</a></dd><dd><a class=text-decoration-none href=/dmca>DMCA</a></dd></dl></div><div class=row><div class="text-center text-sm-start col-sm-4 pe-sm-0"><a href=https://www.facebook.com/pages/ManualShelf/1488826334681423 class="fs-5 text-center d-inline-block social rounded-2 align-middle text-decoration-none me-2"><i class="fab fa-facebook-f"></i></a><a href=https://www.twitter.com/ManualShelf class="fs-5 text-center d-inline-block social rounded-2 align-middle text-decoration-none me-2"><i class="fab fa-twitter"></i></a><a href=https://plus.google.com/+ManualShelf class="fs-5 text-center d-inline-block social rounded-2 align-middle text-decoration-none me-2"><i class="fab fa-google-plus-g"></i></a><a href=http://www.pinterest.com/ManualShelf class="fs-5 text-center d-inline-block social rounded-2 align-middle text-decoration-none"><i class="fab fa-pinterest-p"></i></a></div><div class="col col-sm-8 d-flex flex-column align-items-center flex-sm-row flex-wrap flex-sm-nowrap justify-content-center justify-content-sm-end"><div class="copy w-auto d-flex align-items-center justify-content-center justify-content-sm-end mt-2 mt-sm-0 me-2">ManualShelf © 2013-2024</div><select class="form-select form-select-sm w-auto mt-2 mt-sm-0"><option value=usa>USA</option></select><div></div></div><div id=pixel><script> googletag.cmd.push(function() { googletag.display('pixel'); }); </script></div></footer><script src=/assets/js/jquery-3.3.1.min.js></script><script src=/assets/js/bootstrap.bundle.min.js></script><script src=/assets/js/jquery.autocomplete.min.js></script><script type=text/javascript> $.extend({ redirectPost: function(location, args) { var form = ''; $.each(args, function(key, value) { form += '<input type="hidden" name="' + key + '" value="' + value + '">'; }); form = '<form id="s1" action="' + location + '" method="POST">' + form + '</form>'; $(document.body).append(form); $("#s1").submit(); } }); $(document).ready(function(){ $("#query").autocomplete({ minChars: 3, groupBy: 'type', paramName: 'q', dataType: 'json', serviceUrl: '/autocomplete', noCache: true, showNoSuggestionNotice: true, noSuggestionNotice: 'Zarro results found', onSelect: function (suggestion) { $.redirectPost(suggestion.data.url, {highlight: encodeURIComponent(JSON.stringify(suggestion.data.hls))}); } }); var toc = $('.toc-selector'); if (toc.length) { var slideParams = { duration: 800, easing: 'linear' }; toc.click(function() { $(this).toggleClass('open'); var section = $('.toc-content'); var isCollapsed = section.attr('data-collapsed') === 'true'; if (isCollapsed) { section.slideDown(slideParams) section.attr('data-collapsed', 'false') } else { section.slideUp(slideParams); section.attr('data-collapsed', 'true') } }); } }); var lastSmall = $(window).width() < 576; $(window).resize(function() { var newSmall = $(window).width() < 576; if (lastSmall != newSmall) { lastSmall = newSmall; window.location.href = window.location.href; } }); </script></body></html>