User's Manual

- 9 -
- 10 -
- 11 -
- 12 - - 13 -
Switch
100 meters
PoE
Power
Data
PoE PTZ
IP Camera
802.3at PoE Injector
Power
Data
AC
1000BASE-T UTP
PoE
1000BASE-T UTP with PoE
Power Line (AC)
AC
Figure 2: Connection to IEEE 802.3at / 802.3af Devices
When the ACTIVE LED blinks slowly, it indicates the
port is not providing 53V DC in-line power. Once
the 802.3at PoE Injector detects the existence of
an IEEE 802.3at / 802.3af device, the ACTIVE LED
indicator will be steadily on to show it is providing
power.
Note
1. Since the 802.3at PoE Injector PoE
port supports 53V DC PoE power
output, please check and assure the
powered device’s (PD) acceptable DC
power range is 53V DC. Otherwise, it
will damage the PD.
2. If the connected device is not fully
complying with IEEE 802.3at /
802.3af Power over Ethernet or in-
line power device, the LED indicator
of the 802.3at PoE Injector will not
be steadily on.
The 802.3at PoE Injector and POE-162S, the
IEEE 802.3at Injector Splitter Installation
1. Connect the AC power cord to “AC slot” of the
802.3at PoE Injector; the “POWER” LED will be
steadily on.
2. Connect a standard network cable from the
“POE” port of the 802.3at PoE Injector to the
“PoE In” port of the POE-162S. The “ACTIVE”
LED of the 802.3at PoE Injector and PoE-in-use
LED of the POE-162S will continue to be lit.
3. Connect a standard network cable from a switch /
workstation to the “LAN” port of the 802.3at PoE
Injector.
4. Connect the UTP cable in the package from the
“Ethernet” port of the POE-162S to the RJ45
port of a remote device.
5. Adjust the proper DC power output and connect
the DC plug from the “DC OUT” of the POE-162S
to a remote device.
6. Power on the remote device and its power LED
indicator will remain on.
Switch
Power 12V/24V
POE-162S
100 meters
Power
Data
Power
Data
PoE
Power
Data
AC
DC
Non-PoE PTZ
IP Camera
1000BASE-T UTP
PoE
1000BASE-T UTP with PoE
Power Line (AC)
AC
DC
Power Line (DC)
802.3at PoE Injector
802.3at PoE
Splitter
Figure 3: Connection architecture over 802.3at PoE
Injector / POE-162S
Note
1. Owing to IEEE 802.3at / 802.3af
Power over Ethernet standards, the
802.3at PoE Injector will not inject
power over the cable if not connected
to IEEE 802.3at / 802.3af devices.
2. Please ensure the POE-162S output
voltage is correct before applying
power to remote devices.
The 802.3at PoE Injector and POE-E201 IEEE
802.3at PoE Extender Installation
1. Connect the AC power cord to the “AC slot” of
the 802.3at PoE Injector; the “POWER” LED will
be steadily on.
2. Connect a standard network cable from the
“POE” port of the 802.3at PoE Injector to the
“IN” port of the POE-E201.
3. The 802.3at PoE Injector delivers both Ethernet
Data and PoE power over UTP cable to the
POE-E201 and the “ACTIVE” LED of the 802.3at
PoE Injector and the “PoE IN” LED of the
POE-E201 will continue to be lit.
4. Connect an additional standard network cable that
will be used to connect from the “OUT” port of
the POE-E201 to a remote Powered Device
(PD).
5. The "OUT" port of the power injector transmits
DC voltage over the standard network cable and
transfers data and power simultaneously between
the 802.3at PoE Injector and the PD.
6. Once the POE-E201 detects the existence of an
IEEE 802.3at / 802.3af device, the “PoE OUT”
LED indicator will be steadily on to show it is
providing power.
802.3at
PoE Extender
Data
PoE PoE
+
Power
Power
Data +
Power
Data
100 meters100 meters
200 meters
Power Line (AC)
AC
1000BASE-T UTP
PoE
1000BASE-T UTP with PoE
PoE IP Camera
802.3at PoE Injector
Figure 4: Connection architecture over 802.3at PoE
Injector / POE-E201
Note
1. If the connected device is not fully
complying with IEEE 802.3at /
802.3af standards or in-line power
device, the PoE OUT LED indicator of
the POE-E201 will not be steadily on.
2. Owing to IEEE 802.3at / 802.3af
standards, the POE-E201 will not
inject power over the cable if a
standard IEEE 802.3at / 802.3af
device is not connected.
Customer Support
Thank you for purchasing PLANET products. You
can browse our online FAQ resource at the PLANET
Web site rst to check if it could solve you issue. If
you need more support information, please contact
PLANET switch support team.
PLANET online FAQ :
http://www.planet.com.tw/en/support/faq.php?type=2
Switch support team mail address :
[e-mail]
Copyright © PLANET Technology Corp. 2015.
Contents are subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp.
All other trademarks belong to their respective owners.
EC Declaration of Conformity
For the following equipment:
*Type of Product : Single-Port 10/100/1000Mbps IEEE 802.3at PoE+ Injector (30Watts)
Single-Port 10/100Mbps IEEE 802.3at PoE+ Injector (30Watts)
*Model Number : POE-163, POE-164
* Produced by:
Manufacturer‘s Name : Planet Technology Corp.
Manufacturer‘s Address : 10F., No.96, Minquan Rd., Xindian Dist.,
New Taipei City 231, Taiwan (R.O.C.).
is herewith confirmed to comply with the requirements set out in the Council Directive on the
Approximation of the Laws of the Member States relating to Electromagnetic Compatibility
Directive on (2004/108/EC).
For the evaluation regarding the EMC, the following standards were applied:
EN55022 (2006 + A1:2007 + A2:2010)
EN 61000-3-2 (2006 + A1:2009 + A2:2009)
EN 61000-3-3 (2008)
EN55024 (2010)
IEC 61000-4-2 (2008)
IEC 61000-4-3 (2006+A1: 2007 + A2:2010)
IEC 61000-4-4 (2004 + A1:2010)
IEC 61000-4-5 (2005)
IEC 61000-4-6 (2008)
IEC 61000-4-8 (2009)
IEC 61000-4-11 (2004)
Responsible for marking this declaration if the:
 Manufacturer  Authorized representative established within the EU
Authorized representative established within the EU (if applicable):
Company Name: Planet Technology Corp.
Company Address: 10F., No.96, Minquan Rd., Xindian Dist., New Taipei City 231, Taiwan
(R.O.C.)
Person responsible for making this declaration
Name, Surname Kent Kang
Position / Title : Product Manager
Taiwan 29
th
March, 2013
Place Date Legal Signature
PLANET TECHNOLOGY CORPORATION
e-mail: [e-mail] http://www.planet.com.tw
10F., No.96, Minquan Rd., Xindian Dist., New Taipei City, Taiwan, R.O.C. Tel:[phone] Fax:[phone]