Internet Telephony PBX System IPX-300 Series Quick Installation Guide
Overview PLANET IPX-300/IPX-300W IP PBX telephony systems (“IP PBX” in the following term) are designed and optimized for the small business in daily communications. It can support up to 100 user registrations and easy to install and manage a fully working system with the convenience and cost advantages. The future IP PBX telephony system offers all of the essential features of telephony which is required by small business users for their telecommunication/data needs.
Table of Contents Document Objectives........................................................................................ 4 Document Organization..................................................................................... 5 Preparation before beginning administration on IP PBX........................................ 6 Network Interface quick configurations.......................................................... 7 Step1. Operation Mode (For IPX-300W)............................................
Document Objectives This guide provides physical installation, LAN/WAN IP configurations, and Internet access establishment information for the IP PBX.
Document Organization This guide is organized as follows: • Preparation before beginning administration on IP PBX • Administration interface • LAN/WAN Interface quick configurations
Preparation before beginning administration on IP PBX Physical Installation IPX-300: Internet Telephony PBX System IPX-300W: Wi-Fi Internet Telephony PBX System Figure 1. Front Panel of IPX-300 Figure 2. Front Panel of IPX-300W Figure 3. Rear Panel of IPX-300 Figure 4. Rear Panel of IPX-300W Administration Interface IP PBX provides GUI (Web based, Graphical User Interface) for machine management and administration.
Figure5. Input prompt Note In order to connect machine for administration, please locate your PC in the same network segment (192.168.0.x) of IP PBX. If you’re not familiar with TCP/IP, please refer to related chapter on user’s manual CD or consult your network administrator for proper network configurations. Network Interface quick configurations Wizard for Quick Setup of the IP PBX, after finishing the authentication, please click “Wizard” to enter quick start: Figure 6.
Step1. Operation Mode (For IPX-300W) For most users, Internet access is the primary application. The IP PBX supports the WAN, LAN and WLAN interface for Internet access and remote access. When you click “Operation Mode” from within the Wizard Setup, the following setup page will be show. Three WLAN modes of operation are available for Internet Access: AP Mode: In this mode the IP PBX supports AP functionality only. The IP PBX has the following network interfaces: WAN, LAN and Wireless LAN.
Figure 7. Wizard-Internet settings AP Setting (For IPX-300W) For configuring correctly the WLAN port in client mode, the below instructions will provide a quick start. It is advised if possible to use the simplest network settings for first try. For making sure the IP PBX is connecting to your wireless router (AP). You need to set up the following: SSID, Frequency Channel, Authentication method and Encryption parameters (Type/Encryption length/Keys.) Figure 8. Wizard-AP settings Step3.
DHCP Server Enable to open LAN port DHCP server Assigned DHCP IP Address DHCP server range from start IP to end IP DHCP IP Lease Time Client to ask DHCP server refresh time, range from 60 to 86400 seconds Figure 9. Wizard-NAT settings Step4. IPPBX Setup The IP PBX allows multiple ITSP providers / User Extensions registration by simply fill-in the required information in the provided table. Figure 10.
Service Provider: Caller ID Service provider name Username Input Provider name Password Input Provider password Host Input Providers server address Port Providers server port User Extensions: User Extension Input Extension number Password Input Extension password Caller Id Input Extension caller id After completing the wizard setup, click “Submit” button. The IP PBX will save configuration and reboot IP PBX automatically, after 50 seconds, you can re-load setting page again. Figure 11.
IP Phone and Wi-Fi Phone register to IP PBX In the following samples, we’ll introduce IP Phone and Wi-Fi Phone register to IP PBX applications. Figure 12. Topology of instruction example Machine configuration: STEP 1: Please log in IP PBX via web browser and browse to “Network Setup ⁄ WLAN Setting” configuration menu. Enable the WLAN and setup the related configuration. The sample configuration screen is shown below: Figure 13.
STEP 2: Browse to “IP PBX Setup ⁄ User Extensions Setup” configuration menu. Figure 14. User extension setting of IP PBX STEP 3: Click the “Add” button to create extension account ext.100 and ext.101. Figure 15. Add extension setting of IP PBX STEP 4: Please log in VIP-154T and browser to “SIP setting ⁄ Domain Service” configuration menu. Insert the account/password information then save and reboot machine. The sample configuration screen is shown below: Dat a match with Fi gure 15.
STEP 5: Please take VIP-192 and setup the wireless network to connect with IP PBX (IPX-300W) by keypad menu method. Then log in VIP-192 via web browser and browser to “SIP Settings” configuration menu. Insert the Register and Outbound Proxy IP Address information. The IP address of IP PB X Figure 17. SIP settings of VIP-192 Then browse to “SIP Account Settings” configuration menu and fill in the account/ password information. The sample configuration screen is shown below: Dat a match with Fi gure 15.
3. Then the VIP-192 should ring. Please repeat the same dialing steps on VIP-192 to establish the first voice communication from VIP-154T IP Phone and Wi-Fi Phone make off-Net calls via Gateway In the following samples, we’ll introduce VIP-154T and VIP-192 makes off-Net Calls (PSTN calls) via VIP-480FO applications. Figure 20. Installation example with VIP-480FO Machine configuration: STEP 1: Please refer to the first sample and let VIP-154T and VIP-192 register to IP PBX.
STEP 3: Browse to “IP PBX Setup ⁄ Attendant Extension” configuration menu. Assign an attendant number which inexistence extension in Extension List and the sample configuration screen is shown below: Figure 22. Assign an attendant number Pressing the “Submit” button for activate the configuration. STEP 4: Browse to “IP PBX Setup ⁄ Dialing Rules” configuration menu. Add a dialing rule for making off-Net calls via VIP-480FO, and press the “Insert” button for activate the configuration. Figure 23.
Figure 25. Set up the Hunting Member of FXO ports Figure 26. Set up the Proxy Server IP address for register to IP PBX STEP 6: Browse to “Dialing Plan” configuration menu. Add an Incoming Dial Plan (no.0) for redirect the PSTN outgoing calls to FXO ports. Figure 27. Add an incoming dial plan STEP 7: Browse to “Port Status” configuration menu. Fill in the auto attendant number 555 to all of ports. (Where 555 is the autoattendant number of IP PBX) Figure 28.
STEP8: After all of devices have registered to IP PBX successfully, the Extension Status page will show the registration status: Figure 29. Extension status page with Phone and Gateway registered Test the scenario: 1. VIP-154T pick up the telephone 2. Dial the number: 0 shall be able to connect to the port 1 of VIP-480FO 3. Then the telephone will hear the dial tone from PSTN lines, and dial the number: 12345678 shall be able connect to the User A. 4.
Quick reference in CD-ROM guide This guide is used to help you startup your Wizard settings. It is also recommended to check the user manual CD-ROM for more details likes the “IP PBX Setup”, and how to set the device back to default value.
This page is intentionally left blank
