24-Port 10/100/1000Mbps with 4 Shared SFP Managed Gigabit Switch WGSW-24040 / SGSW-24040 Quick Installation Guide
Table of Contents 1. Package Content.......................................................................................... 3 2. Requirements.............................................................................................. 4 3. Terminal Setup............................................................................................ 5 4. Logon to the Console................................................................................... 6 5. Configure IP address...........................
1. Package Content Thank you for purchasing PLANET Layer 2 Managed Switch, WGSW-24040 / WGSW-24040R / SGSW-24040 / SGSW-24040R. Terms of “Managed Switch” means the Switches mentioned titled in the cover page of this Quick installation guide, i.e. WGSW-24040 / SGSW-24040. Open the box of the Managed Switch and carefully unpack it.
2. Requirements ó Workstations of subscribers running Windows 98/ME, NT4.0, 2000/XP, MAC OS9 or later, Linux, UNIX or other platform compatible with TCP/IP protocols. ó Workstation installed with Ethernet NIC (Network Card) ó Serial Port connect (Terminal) ó Above PC with COM Port (DB-9) ó Ethernet Port connect > Network cables - Use standard network (UTP) cables with RJ45 connectors.
3. Terminal Setup To configure the system, connect a serial cable to a COM port on a PC or notebook computer and to serial (console) port of the WGSW / SGSW Managed Switch. The console port of the Managed Switch is DCE already, so that you can connect the console port directly through PC without the need of Null Modem. A terminal program is required to make the software connection to the WGSW / SGSW Managed Switch. Windows’ Hyper Terminal program may be a good choice.
4. Logon to the Console Once the terminal has connected to the device, power on the WGSW / SGSW Managed Switch, the terminal will display that it is running testing procedures. Then, the following message asks the login password. The factory default password as following and the login screen in Figure 4-1 appears. Password: admin Figure 4-1 WGSW / SGSW Managed Switch Console Login screen Note 1. For security reason, please change and memorize the new password after this first setup. 2.
5. Configure IP address The WGSW / SGSW Managed Switch is shipped with default IP address as following. IP Address : 192.168.0.100 Subnet Mask : 255.255.255.0 To check the current IP address or modify a new IP address for the Switch, please use the procedures as follow: Show the current IP address 1. On “Switch/>” prompt, enter “show ip”. 2. The screen displays the current IP address, Subnet Mask and Gateway. As show in Figure 5-1.
Configure IP address 3. On “Switch/>” prompt, enter the following command and press . As show in Figure 5-2. Switch/> ip setup 192.168.1.100 255.255.255.0 192.168.1.1 The previous command would apply the follow settings for the Switch. IP: 192.168.1.100 Subnet Mask: 255.255.255.0 Gateway: 192.168.1.1 Figure 5-2 Set IP address screen 4. Repeat Step 1 to check if the IP address is changed. If the IP is successfully configured, the Managed Switch will apply the new IP address setting immediately.
6. Start Web Management The following shows how to start up the Web Management of the WGSW / SGSW Managed Switch. Note the Managed Switch is configured through an Ethernet connection, please make sure the manager PC must be set on the same IP subnet address. For example, the default IP address of the WGSW / SGSW Managed Switch is 192.168.0.100, then the manager PC should be set at 192.168.0.x (where x is a number between 1 and 254, except 100), and the default subnet mask is 255.255.255.0.
2. When the following dialog box appears, please enter the default password “admin” (or the password you have changed via console). The login screen in Figure 6-2 appears. Default Password: admin Figure 6-2 Login screen 3. After entering the password, the main screen appears as Figure 6-3. Note The following screen based on WGSW-24040 for SGSW-24040 the display will be the same for WGSW-24040.
4. The Switch Menu on the left of the Web page let you access all the commands and statistics the Switch provides. Figure 6-4 Switch Menu Note If you do not familiar with Switch functions or the related parameter, press “Help icon” anytime in right-top of the Web page to get the help description. Now, you can use the Web management interface to continue the Switch management or manage the Switch by console interface. Please refer to the user manual for more.
Customer Support Thank you for purchase PLANET products. You can browse our online FAQ resource at the PLANET website first to check if it could solve you issue. If you need more support information, please contact PLANET switch support team. PLANET online FAQ : http://www.planet.com.tw/en/support/faq.php?type=1 Switch support team mail address : support_switch@planet.com.
