SIP IP Phone -- with PSTN Connectivity User’s Manual
Table of Contents Chapter 1 Overview of the VIP-150T ...............................................................................................1 1.1 Hardware Overview................................................................................................ 1 1.1.1 Front View and Keypad function .................................................................. 1 1.1.2 Back View .................................................................................................... 4 1.1.
4.12 [sysconf] command ............................................................................................ 35 4.13 [sip] command .................................................................................................... 36 4.14 [security] command ............................................................................................ 37 4.15 [voice] command ................................................................................................ 37 4.16 [tos] command...........
Chapter 1 Overview of the VIP-150T VIP-150T is a full-featured IP-based telephone set via Ethernet base communication. Over the office LAN connection, it provides IP-PBX solution such as station-to-station call, IP call and local PSTN/PBX Extension call via PSTN Gateway. VIP-150T provides two 10/100BaseT switch/hub RJ-45 ports allow connecting to office LAN and PC simultaneously.
♦ ♦ ♦ ♦ ♦ ♦ LCD: 2 lines, 24 character Dot Matrix display. C: Jump out current LCD menu. ç : Move to previous selection or clear previous data. è : Move to right or next selection. OK: Press OK to confirm the modification. Direct Line (DL) Button 1 – 10: User press DL button after off-hook to do speed dial according to phone book data from 1-10 (please refer to LCD configuration-3.Phone Book; Advanced Configurations via Telnet- 5.[pbook] command, or Web Configuration-Phone Book chapter.
♦ ♦ HOLD: To hold a call, after press HOLD button, both sides will hear hold tone. SPEED: Press SPEED and number (Phone book index) after off-hook can do speed dial according to phone book data (please refer to 3.LCD configuration-6. Phone Book or Advanced Configurations via 4.Telnet- 5.[pbook] command). ♦ FORWARD: Forward an incoming call to another IP device.
1.1.2 Back View ♦ ♦ DC 9V: DC 9V power input outlet LAN: RJ-45 connector, connected directly to the Hub through the straight CAT-5 cable. ♦ ♦ PC: RJ-45 connector, connected directly to the PC through the straight CAT-5 cable Line: RJ-11 connector, connected directly to the PSTN analog line. ? Note: There are two LED indicated lights: LINK/ACT and 10/100 for LAN port and PC port.
1.
Provisioning and Configuration l SIP (RFC3261) compliance l LCD configuration password protection l Provide Proxy Mode or Peer-to-Peer Mode (Non Proxy Server needed) selection l Ring tone, Speaker and Handset volume adjustable l Dial path selection (PSTN or IP mode) l Support DNS server inquiry Management Features: l Software Upgrade: TFTP/FTP download l Three easy ways for system configuration - LCD Front Panel - Web Browser - TELNET Environmental l Humidity: 10 to 90 % (Non-condensing) l Operational Temp
Chapter 2 Configuring the VIP-150T through LCD Phone menus ? Note: 1. After any configuration is made for the VIP-150T, user has to do Reboot in the selection 7 “Reboot”. 2. We suggest user to set IP address via LCD menu 5→2.3.4.5 first, then go to chapter 3 to do other detail configurations via web browser. 2.1 Initialize VIP-150T 1. When power on the VIP-150T, the LCD screen shows as below. Now VIP-150T is running Boot sector program. VIP-150T Board Start Booting 2.
mode. (**) PSTN VIP-150T 10:10:10 AM 6. Press ç or è to enter configuration mode then press OK button to enter sub menus; press C can jump out current menu to previous level. 1. 2. 3. 4. 5. 6. 7. Call List (**) Forward Type Phone Book Ringer Settings Network Advanced Settings (protected by password) Reboot 2.2 LCD Menu Configuration User can set the following configurations by LCD keypad. ? 1. Press TRANSFER before input data can switch characters to be capital or lowercase. 2.
2. Forward Type (**) There are 3 selections in Forward type, user must select under which condition to forward calls. (1) Busy When VIP-150T is in busy status, the incoming call will be forwarded to the assigned phone number. A. Activate Enter a forwarded phone number to activate busy forward function. B. Deactivate Deactivate Busy Forward function. (2) No Response When VIP-150T hasn’t been picked up for around 10 seconds, the incoming call will be forwarded to the assigned phone number. A.
Add a new record of name, telephone number, and IP address of the phone address book. 4. Ringer Settings 1. Volume User can adjust ring volume by press ç or è on the keypad to decrease or increase ringer volume. 2. Style There are three tone styles for VIP-150T. Move the “>” symbol by press ç or è on the keypad to select the tone style preferred, then press OK to confirm it. 5. Network 1.
(3) Auto Re-connect Choose ON or OFF to enable or disable this function. If user enables this function, after PPPoE disconnected, VIP-150T will automatically reboot to re-connect, and after reboot, if VIP-150T still can’t connect with server, VIP-150T will keep trying to connect. On the other hand, if user disables this function, VIP-150T won’t reboot and keep trying to connect. 8.
Select SIP connection mode to be peer-to-peer mode or Proxy mode. (2) Proxy A. Proxy Set Proxy IP address or Domain Name. B. Outbound proxy Set Outbound Proxy IP address or Domain Name. C. Proxy port Set Proxy port for VIP-150T to send messages. D. Expire (in seconds) Set expire time of registration, in the duration of 2/3 expire time, VIP-150T will re-register to Proxy Server again. (3) User Info A. User Name Set User Name of VIP-150T to register to Proxy Server.
(5) Start to Upgrade Select YES or NO to start upgrade. After download is finished, press OK then VIP-150T will ask if need to reboot. (**) (6) Firmware Version Show versions of all software and hardware. (**) ? Note: 2. Download via LCD command can only upgrade new application rom file. LCD Menu Password Set entry password of phone LCD menu. 7. Reboot Reboot machine. It is necessary and important for user to reboot VIP-150T after any configurations has been made.
Chapter 3 Configuring the VIP-150T through Web Pages The HTTPD web management interface provides user an easier way to configure rather than command line method through TELNET. The configuration function and steps are similar with the way through command line. Please refer to the chapter 4- Configuring the VIP-150T through Telnet command lines for more detail information. Below is a guide for user to configure via web interface. Step 1.
Step 3. Enter the web interface main screen After enter login name and password, user can see web interface main screen as below. Step 4. Start to configure Most important items are Network Interface, SIP Configurations, and Phone Book (in Peer-to-Peer mode). Please remember to configure these commands before start to work with VIP-150T. ? Note: After change any settings, please remember to reboot VIP-150T so that changes can take effect.
1. Network Interface Please refer to chapter 4.9 [ifaddr] command. - IP Address: Set IP Address of VIP-150T Subnet Mask: Set the Subnet Mask of VIP-150T Default routing gateway: Set Default routing gateway of VIP-150T Get IP Mode: User has to set VIP-150T to use which network mode. 1. Fixed IP: User has to assign a fixed IP to VIP-150T. 2. DHCP: When DHCP function enables, VIP-150T will automatically search DHCP server after reboot. 3.
- SNTP: Enable / Disable the Simple Network Time Protocol function PLANET VIP-150T User’s Manual 17
- - - - SNTP Server Address: Set SNTP Server Address When SNTP server is available, enable VIP-150T SNTP function to point to SNTP server IP address so that VIP-150T can get correct current time. GMT: Set time zone for SNTP Server time User can set different time zone according to the location of VIP-150T. For example, in Taiwan the time zone should be set as 8,which means GMT+8. IP Sharing: Enable it if VIP-150T is behind IP Sharing router.
2. SIP Configurations Please refer to chapter 4.13 [sip] command - Operation Mode: Select VIP-150T to work under Peer-to-Peer mode or Proxy mode. Proxy Server: Set Proxy Server or URL address (Domain Name Server must be - configured. Please refer to Network Interface). Outbound Proxy: Set IP Address or URL address (Domain Name Server must be - configured. Please refer to Network Configure) of outbound Proxy server.
- - Line Number: identify one number for the VIP-150T to register to the Proxy. Line Account: set user name of VIP-150T for registering. User can set user name and password for registering. If password is no need, please set user name the same as line number or VIP-150T won’t register successfully. Line Password: set password for registering. SIP Port: set SIP UDP port. RTP Port: set RTP port for sending voice data. Expire Time: set expire time of registration.
3. System Configuration Please refer to chapter 4.12 [sysconf] command - - - Keypad DTMF Type: set DTMF type. User can select DTMF type VIP-150T transmits. RFC2833 Payload Type: change RFC2833 Payload type. This is for special request from the other site, if RFC2833 payload type of 2 sites are different, it may cause some problem of connection. Interval between Dialstring Digits: Set the DTMF inter digit time (second) To set the duration (in second) of two pressed digits in dial mode as timed out.
4. PPPoE Configuration Please refer to chapter 4.10[pppoe] command - - User Name: Set PPPoE authentication User Name. Password: Set PPPoE authentication password. Reboot After Remote Host Disconnection: Enable/Disable auto reboot after PPPoE disconnection If user enables this function, after PPPoE being disconnected, VIP-150T will automatically reboot to re-connect, and after reboot, if VIP-150T still can’t get contact with server, VIP-150T will keep trying to connect.
5. Voice Setting Please refer to chapter 4.15 [voice] command - - Codec Priority: set codecs priority in order. Please notice that user can set from 1 to 5 codecs as their need. For example, user can only set first priority as G.723.1, and set the others as x, that means only G.723.1 is available. Sending Packing Size: User can set different packet size for each codec. G.723 Silence Suppression: Enable / Disable sound compression and comfort noise generation. It is only for codec G.723.
6. Phone Book Please refer to chapter 4.5 [pbook] command - Add Entry: User can specify 20 sets of phone book via web interface. Please input index, Name, IP Address and E.164 number of the destination device. Delete Entry: User can delete any configured phone book data by index.
7. DDNS Configuration Please refer to chapter 4.
8. Version Information Please refer to chapter 4.19 [rom] command Boot: Boot loader version VIP-150T - Application: Default: This field has no default value. Application image version information of VIP-150T. - Default: This field has no default value. DSP Version: DSP image version information. - Default: This field has no default value.
9. Password Please refer to chapter 4.20 [passwd] command - CHANGE: First select login name as root or administrator, then enter current password, new password and confirm new password again to set new password. ABORT: Press abort will clean all inputs.
10. Firmware Upgrade Please refer to chapter 4.19 [rom] command - Server IP Address: Set TFTP server IP address Target File name: Set file name prepared to upgrade Download Method: Select download method as TFTP or FTP FTP Login: Set FTP login name and password Target File Type: Select which sector of VIP-150T to upgrade ? Note: 1. After 2mb file download is finished, all configurations might change to default values, user has to configure again. 2.
11. Reboot Please refer to chapter 4.4 [reboot] command - Press reboot will reset VIP-150T. ? Note: To execute reboot via web browser, VIP-150T will automatically save all data before reboot. To execute reboot via TELNET command.
Chapter 4 Configuring the VIP-150T through Telnet command lines After setting the IP Address of VIP-150T and reboot, (please refer to LCD Menu: 5-3.4.5), user can enter into Telnet command lines. ? Note: 1. After user enter VIP-150T configuration via telnet, please use login: ”root”, password: null, press enter to enter command lines. 2. User must input lower-case command, but contents of configurations such as SIP alias or user name etc, user can set as capital case. 3.
4.3 [debug] command This command is for engineers to debug system of VIP-150T. User can add debug flag via command debug –add “debug flags”, and then start debug function via command debug –open. When VIP-150T is working on screen will display related debug messages. Most frequently used debug flag are “sip”, “fsm”, “msg”…etc. 4.4 [reboot] command After typing commit command, type reboot to restart the VIP-150T.
“index number”) 5. -insert: insert an record in specified index of phone book. 6. -modify: modify record of a certain index in phone book . Please notice that the name, IP address and e164 number must be modified together; user cannot just modify one parameter only. (pbook –modify “index” name “X” ip “xxx.xxx.xxx.xxx” e164 “X”) 4.6 [commit] command Save any changes after configuring the VIP-150T. 4.7 [ping] command Command ping can test which the IP address is reachable or not.
4.8 [time] command When VIP-150T enable SNTP function and be able to connect with SNTP server, type time command will show the current time retrieved from SNTP server. .......................................................................................................................................................... 4.9 [ifaddr] command Configure and display the VIP-150T IP information. 1. –print: print out all current configurations of ifaddr command. 2.
(GMT-8: ifaddr –timezone -8) 5. -ipsharing: If VIP-150T is behind a IP-sharing , user must enable IP sharing function and specify public IP address.(ifaddr –ipsharing 0/1 “public IP address of IP sharing” , 0 for disable and 1 for enable) ? Note: Some Proxy servers support endpoint behind NAT function, in this case VIP-150T doesn’t have to enable IP sharing function, please contact with your Proxy Server vendor. 6. –upnp: enable/disable UPnP function.
4.11 [flash] command This command will clean the configuration stored in the flash rom to default value and reboot the VIP-150T. ? Note: 1. After user upgrade new software version, suggested to execute this command to make sure new software work well on VIP-150T. 2. To execute the command flash –clean, all configuration of VIP-150T stored in flash will be cleaned. It is authorized for the user whose login name is “root” only. 4.12 [sysconf] command 1. -print: display all current configurations. 2.
4.13 [sip] command 1. –print: display all current configurations. 2. –mode: configure VIP-150T as Proxy or Peer-to-Peer Mode. Usage: sip –mode 0/1(1 for Proxy mode, 0 for Peer-to-Peer mode) 3. –px: set proxy server IP address or URL address (sip –px “IP address or URL of Proxy server”). 4. –pxport: set listening port of Proxy server. 5. –outpx: set IP address of outbound proxy server. After user set outbound proxy, all packets form VIP-150T will be sent to outbound proxy server. 6.
4.14 [security] command 1. –print: display all current configurations. 2. -name: set user ID of VIP-150T for registering. User can set user name and password for registering. If password is no need, please set user name the same as line number or VIP-150T won’t register successfully. 3. –pwd: set account password for registering. 4.15 [voice] command The voice command is associated with the voice codec setting information. 1. -print: display voice codec information and configuration. 2.
711a g711u g729 g729a means VIP-150T can support only one codec or four codecs. 4. -volume: There are three types can be adjustable, voice volume, input gain and DTMF volume. Voice volume means the volume user can hear, input gain means the volume the other side can hear from VIP-150T, DTMF means DTMF transmitting volume. (voice –volume voice “value of volume”, voice –volume input “value of volume”, voice –volume dfmt “value of volume”) ? Note: If value of volume set as 0 means –32db, 1 means –31db…etc.
4.16 [tos] command TOS/DiffServ (DS) priority function can discriminate the Differentiated Service Code Point (DSCP) of the DS field in the IP packet header, and map each Code Point to a corresponding egress traffic priority. As per the definition in RFC2474, the DS field is Type-of-Service (TOS) octet in IPv4. The recommended DiffServ Code Point is defined in RFC2597 to classify the traffic into different service classes.
4.17 [ddns] command -print: display DDNS overall information and configuration. 2. -enable: to enable/disable DDNS function.(ddns –enable 0/1, 0 for disable and 1 for enable). 1. 3. -server: to set IP address of DDNS login server. 4. -hostname: to set the registered Domain Name of VIP-150T. (ex. ddns –test.ddns.org) 5. -id: to set login ID of registered account to log in DDNS server. 6. -passwd: to set password of registered account to log in DDNS server. 7. -checkip: to enable/disable check IP function.
4.18 [bureau] command 1. -print: Display Bureau line information and configuration 2. -hotline: Set Hot line information 4.19 [rom] command 3. -print: show all current configurations and version information. 4. -app,-boot, -dsptest, -dspcore, -dspapp,: upgrade main boot code, main application code, DSP testing code, DSP kernel code, DSP application code, Ring Back Tone PCM file and Hold Tone .
Command rom –print can show current version installed in VIP-150T. 4.20 [passwd] command For security protection, user has to input the password before entering application user/config mode. Two configurations of login name/password are supported by the system. 1. –set: set password of “root” users or “administrator” users. (passwd –set root/administrator “password”) 2. –clean: clean up password restored before, and user can login :”root/administrator”, password: ”press enter”.
PLANET VIP-150T User’s Manual 43
Chapter 5 Upgrading Software on the VIP-150T VIP-150T supports three methods to upgrade the new version. All methods are necessary to prepare the TFTP or FTP program on the host PC as TFTP/FTP server. After installing TFTP/FTP program on one PC and connecting to network, VIP-150T is ready to be upgraded. 1. LCD Panel Control 2. Remote Control: Telnet 3. Web Management 5.1 From LCD Phone Menu Please choose the 6→2 selection-Firmware Upgrade. Press OK to enter into the sub-selection as below. 1.
5.2 Web Management Please refer to chapter 4.18 [rom] command - Server IP Address: Set TFTP server IP address Target File name: Set file name prepared to upgrade Download Method: Select download method as TFTP or FTP FTP Login: Set FTP login name and password Target File Type: Select which sector of VIP-150T to upgrade ? Note: 1. After 2mb file download is finished, all configurations might change to default values, user has to configure again. 2.
2. -app,-boot, -dsptest, -dspcore, -dspapp,: upgrade main boot code, main application code, DSP testing code, DSP kernel code, DSP application code, Ring Back Tone PCM file and Hold Tone . ? Note: After upgrade Application, please remember to execute flash –clean command, which will clean all configurations become factory values except IP address. 3. -boot2m: to upgrade 2mb rom file, which includes all firmware file mentioned in item 2. 4.
