SIP IP Phone VIP-154T/VIP-154PT/VIP-154NT User’s manual Version 2.
Copyright Copyright (C) 2008 PLANET Technology Corp. All rights reserved. The products and programs described in this User’s Manual are licensed products of PLANET Technology, This User’s Manual contains proprietary information protected by copyright, and this User’s Manual and all accompanying hardware, software, and documentation are copyrighted.
Revision User’s Manual for PLANET SIP IP Phone: Model: VIP-154T/VIP-154PT/VIP-154NT Rev: 2.2 (2008, February) Part No. EM-VIP154V2.
TABLE OF CONTENTS Chapter 1 ................................................................................................ 6 Introduction............................................................................................ 6 Overview............................................................................................................................6 Package Content ...............................................................................................................
Port Settings..............................................................................................................36 Codec Settings ..........................................................................................................36 Codec ID Setting ......................................................................................................37 DTMF Settings .........................................................................................................38 RPort Settings ...
Chapter 1 Introduction 1 Overview Meeting the next-generation Internet telephony service demands, PLANET Technology provides feature-rich, toll-quality Internet telephony service solutions. The built-in PSTN interface provides user more convenience between IP Phone and PSTN call selections. －VIP-154NT. With 802.3af Power over Ethernet (PoE) IP Phone－VIP-154PT. And the VIP-154T is the cost-effective SIP IP Phone; the VIP-154 series are SIP 2.0 (RFC3261) compliant with SIP digest authentication supports.
Configuration of the IP Phone can be performed in minutes via the LCD menu keypad, telnet, or web interfaces. Using the built-in LCD display, the IP Phone offers user-friendly configuration guidelines, machine operation status, call status displays, and incoming call identification. • IP PBX system integration Via auto-config support for IPX-2000, no expertise required to establish your office voice network. VIP-154 series can help you to complete VoIP network deployment in minutes.
Package Content The contents of your product should contain the following items: VoIP IP Phone Power adapter Quick Installation Guide User’s Manual CD RJ-11 cable x 1 Physical Details The following figure illustrates the front/rear panel of IP Phone.
Rear Panel of VIP-154NT 1 RESET 2 PC Reset to the factory default setting RJ-45 connector, to maintain the existing network structure, connected directly to the PC through straight CAT-5 cable RJ-45 connector, for Internet access, connected directly to Switch/Hub through straight CAT-5 cable. 3 LAN The LAN interface also can be connected with 802.3af PoE switch or converter for power supply (VIP-154PT) 4 12V DC 5 LINE LNote 12V DC Power input outlet FXO interface, for connect with PSTN line.
Front View and Keypad function Keypad Description 1 LCD Display Speed Dial 2 M1~M4 3 MENU 4 Vol +/↑ Menu and all status shall be displayed for users. To make a speed dial call by pressing the speed dial key M1 ~ M4. To bring out the menu selection while IP Phone is in idle state. To increase the volume of voice when at off-hooked state. To page up menu when at configuration mode. To decrease the volume of voice when at off-hooked state. 5 Vol - /↓ To page down menu when at configuration mode.
To transfer an active call (incoming call answered or outgoing 9 TRANSFER 10 CONF Press this button can make conference function. 11 FWD To carry out forward function. call accepted) to another devices. Press to delete digits when at configuration mode or input 12 DEL/MUTE phone numbers. Press to mute sounds when at talk mode. 13 Redial 14 Handfree 15 Hold 16 Call Log Press to dial the last dialed number when the IP Phone is off-hooked.
Chapter 2 Preparations & Installation 2 Physical Installation Requirement This chapter illustrates basic installation of IP Phone • Network cables. Use standard 10/100BaseT network (UTP) cables with RJ45 connectors. • TCP/IP protocol must be installed on all PCs. For Internet Access, an Internet Access account with an ISP, and either of a DSL or Cable modem Administration Interface PLANET IP Phone provides GUI (Web based, Graphical User Interface) for machine management and administration.
LNote In order to connect machine for administration, please locate your PC in the same network segment (192.168.0.x) of IP Phone. If you’re not familiar with TCP/IP, please refer to related chapter on user’s manual CD or consult your network administrator for proper network configurations. LAN IP address configuration via web configuration interface Execute your web browser, and insert the IP address (default: 192.168.0.1) of VIP in the adddress bar.
After confirming the modification you’ve done, Please click on the Submit button to apply settings and browse to “Save & Reboot” menu to reboot the machine to make the settings effective. Connection Type Data required. In most circumstances, it is no need to configure the DHCP Fixed IP settings. DHCP clinet The ISP will assign IP Address, and related information.
Chapter 3 Network Service Configurations 3 Configuring and monitoring your IP Phone from web browser The IP Phone integrates a web-based graphical user interface that can cover most configurations and machine status monitoring. Via standard, web browser, you can configure and check machine status from anywhere around the world. Overview on the web interface of IP Phone With web graphical user interface, you may have: More comprehensive setting feels than traditional command line interface.
IP Phone main page 16
Chapter 4 VoIP Telephone Adapter Configurations 4 Phone Book settings IP Phone can set up 140 records of Phone Book. User can make calls via Phone Book feature of IP Phone. Field Phone Book Page Phone Name URL Select Description The default is Page 1. It can select Page1 ~ Page 14 to look round Phone Book records. The record number from 0 ~ 139, it can set up 140 records in total. The name of Phone Book records, it only can input numerals. Fill in the outgoing number (Line Number) or IP address.
If you need to add a phone number into the Phone Book list, you need to input the position, the name, and the phone number (by URL type). When you finished a new phone list, just click the “Add Phone” button. If you want to delete a phone number, you can select the phone number you want to delete then click “Delete Selected” button. If you want to delete all phone numbers, you can click “Delete All” button. For Example: STEP 1: IP Phone had added the above phone numbers.
202 192.168.1.2:5062 STEP 4: Pick up the telephone handset or press Handfree button to dial to this telephone. IP Dialing.. 1 192.168.1.2:5062 Speed Dial settings In Speed Dial setting function you can add/delete Speed Dial number. You can input maximum 10 entries speed dial list. You can setup the Speed Dial number. If you want to use Speed Dial you just dial the speed dial number (from 0~9) and follow the “#” key.
Call Forward This page defines Call Forward function. You can setup the phone number you want to forward in this page. There are three type of Forward mode. You can choose All Forward, Busy Forward, and No Answer Forward by click the icon. All Forward: All incoming call will forward to the number you chosen. You can input the name and the phone number in URL field. If you select this function, then all the incoming call will direct forward to the speed dial number you choose.
Call Forward function for VIP-154T/VIP-154PT Call Forward to PSTN (VIP-154NT): VIP-154NT not only support Call Forward to IP calls, but also can forward the calls to PSTN. You can choose the Call Forward type with PSTN, then input the name and the PSTN number in URL/Number field. Call Forward function for VIP-154NT SNTP settings This page defines the primary and second SNTP Server IP Address, to get the date/time information.
When you finished the setting, please click the Submit button. Volume Setting This page defines the Handset Volume, Ringer Volume, and the Handset Gain. When you finished the setting, please click the Submit button. Handset Volume is to set the volume for you can hear from the handset.(Handfree mode) Speaker Volume is to set the volume for you can hear from the speaker. Ringer Volume is to set the ringer volume for you can hear. Handset Gain is to set the volume send out to the other side’s handset.
PSTN-Out Volume is to set the volume for you can hear from the PSTN line. PSTN-In Gain is to set the volume send out to the other PSTN side’s haneset. Volume Settings for VIP-154NT Ringer Setting This page defines the user can set the tinkle of bells when someone ring your IP Phone. If want to set ringer, it need to enable Ringer function and select the Ringer Type you wanted. There are four Ringer Types can be chosen. When you finished the setting, please click the Submit button.
time is large than the “To” time, the Block time will from Day 1 to Day 2. When you finished the setting, please click the Submit button. Auto Answer settings (For VIP-154NT) This page defines the Auto Answer function. You can set the Auto Answer function to answer the incoming call by the phone. If the call is come from the IP, then the VIP-154NT can let user to redial the call to PSTN phone number. If the call is coming from PSTN, then the VIP-154NT can let user to redial to IP Phone number.
Field Description Drop Prefix The rule of add or replace code. If setup as No, it will add the prefix number prior to the identification number. If setup as Yes, it will replace the identification number. Replace rule The prefix number. It only accept the numeral and the max length is 8. + The identification number. It can accept the numeral or symbol and the max length is 40. Symbol: It only accept the [+], [x] +: It means as “or”.
when receive the [#] key. The system also will to determine the Auto Dial Time, it will carry out the calling if there isn’t receive the digit after the Auto Dial Time. If setup as No, the system just according to the Auto Dial Time to determine the end time. Use * for IP dialing If setup as Yes, the system will look on [*] as [.]. For example, if dial the “192*168*0*100#”, it will dial out as “192.168.0.100#”. If setup as No, it just look on [*] as [*].
Routing to: It can select IP or FXO for the auto routing function. Machine will according to the Routing rule to dial out by IP or FXO method. Routing rule: The Routing rule feature has drop number function, and it can use “+” to separate for many routing rules. Example: Routing rule : D007+009 1. When the dialing numbers are start as “007”, for example 00712345678. It will drop 007 then number become 12345678, and according to Routing to setting to select the routing way. 2.
Voice Mail Settings This page defines the voice mail key function. When device register to IP PBX and it support Voice Mail System. It can set up the voice mail number in advanced, and press the “MESSAGE” button from keypad. It will enter for voice mail system. Hot line Settings This page defines the Hot line setting in this page. When user pick up the handset, the device will call to the specific number automatically. Use Hot Line: Click Enable to carry the Hot line function out.
Alarm Settings This page defines the Alarm setting in this page. It provides the alarm function, and it can set up the Alarm Time to get the telephone ringed up every day. Alarm: The default is Off. If set up as On, the telephone will ringed up at the specific time. Alarm Time: It can set up the system prompt time with 24 hours. Current time: The next alarm time. LAN Settings This page defines the LAN setting in this page. LAN Mode: The default is Bridge mode, and it also provides NAT mode.
PC Settings This page defines the PC setting in this page. IP: The IP address of PC port. (In the Bridge mode, the Default IP: 192.168.0.1) Mask: The sub net address. (Default: 255.255.255.0) MAC: The MAC of PC port DHCP Server: It will allot the IP address automatically when enabke this function. Start IP: Start IP of lease table End IP: End IP of lease table.
DDNS Settings This page defines the DDNS setting in this page. You need to have the DDNS account and input the informations properly. You can have a DDNS account with a public IP address then others can call you via the DDNS account. But now most of the VoIP applications are work with a SIP Proxy Server. When you finished the setting, please click the Submit button.
VLAN Settings This page defines the VLAN setting in this page. This function needs to co-operate with network devices which have VLAN function. VLAN Packets: If setup as On, it could receive VLAN messages. VID (802.1Q/TAG): Dispose VLAN ID is add a Tag header after realize enable the VLAN function. The realized voice packets transfer at the same VLAN. The prerequisite is it must the same as VLAN of upper switch. The value range are 2~4094. User Priority (802.1P): To setup the user priority.
Virtual Server This page defines the Virtual Server setting in this page. You could define 24 virtual service information in this page. When you finished the setting, please click the Submit button. Virtual Server Page: There are total page1 to page 3. It could choose the page which want to go over. Num: The serial number. There are total 24 records from Num 0 to 23. Enable: The activate status. The default is Disable, this record will been activate if enable.
PPTP Settings This page defines the PPTP setting in this page. You could setup the PPTP Server connection information. When you finished the setting, please click the Submit button.
Service Domain Settings This router comes with the built-in firewall based on the advanced technology of Stateful Packet In Service Domain Function you need to input the account and the related informations in this page, please refer to your ISP provider. You can register three SIP account in the Phon. You can dial the VoIP phone to your friends via first enable SIP account and receive the phone from these three SIP accounts.
2*: Realm 2 3*: Realm 3 For example: The default is realm 1, input the 2* (Follow by the # key) from keypad and hang up the telephone set. It will switch to realm 2, and it can make the SIP calls via realm 2. Port Settings This page defines the SIP and RTP port number in this page. Each ISP provider will have different SIP/RTPport setting, please refer to the ISP to setup the port number correctly. When you finished the setting, please click the Submit button.
Codec ID Setting This page defines the Codec ID. Sometimes 2 VoIP device with different Codec ID will cause the interopability issue. If you are talking with others got some problems, you may ask the other one what kind of Codec ID he use then you can change your Codec ID. When you finished the setting, please click the Submit button.
DTMF Settings This page defines the DTMF parameters. Yyou can setup the InBand DTMF, 2833 Out-Band DTMF and Send DTMF SIP Info Enable/Disable in this page. To change this setting, please following your ISP information. When you finished the setting, please click the Submit button. RPort Settings This page defines the RPort Enable/Disable in this page. To change this setting, please following your ISP information. When you finished the setting, please click the Submit button.
others Internet devices. SIP Expire Time: To setup the registration interval time. Use DNS SRV: The default is disable, and use DNS SRV mode. Set enable to use DNS to SRV mode to search the host information. Send Keep Alives Pcaket: To deliver the packets on a regular time schedule to keep NAT port could open continued. Keep Alives Period: To setup the schedule time for delivering the packets. Jitter Buffer: To setup the Jitter Buffer size, and the unit is packet.
Auto Configuration This page defines the Auto Configuration (Auto Provision) setting. IP Phone supports TFTP, FTP, HTTP and IP PBX auto configuration function in total. In IP PBX Auto Configuration Setting you need to check with your service provider if they have provided this function. Usually this function will be boundle with an IP PBX to use in the office. PTT Settings (For VIP-154NT) This page defines the PTT settings.
symptom. MAC CIone Setting This page defines the MAC Clone Enable/Disable. This function will copy the MAC address from NIC (Network Interface Card) which placed in PC to LAN port of IP Phone. That because some ISP will limit the MAC address for PPPoE dial-up connection. Please refer to the following operate procedures for more understandings to carry out the MAC Clone function. 1. Please login IP Phone and browse to “Network -> LAN Settings” page.
2. Please make sure the network cable of your PC directly connect with PC port of IP Phone, then re-login IP Phone. (In the NAT mode, the default IP address of PC port is http://192.168.123.1 ) 3. Please browse to “Advanced Settings -> MAC Clone Setting” page and enable the MAC Clone function. 4. IP Phone will prompt if sure want to clone the MAC of your PC to the LAN port of IP Phone. 5. After Save&Reboot, the MAC of LAN port will become to PC’s original MAC address.
Advanced Settings This page defines the advanced functions. When you finished the setting, please click the Submit button. ICMP Not Echo: This function can disable echo when someone ping this device, it can avoid haker try to attack the device. Send Anonymous CID: If enable this function, machine will to start the calling hidden function, and it will not send the related Caller information.
General Debug, SIP Debug, Call Statistics + SIP Debug, General Debug + SIP Debug and All. System Authority In System Authority you can change your login password. Save & Reboot In Save & Reboot you can save the changes you have done. If you want to use new setting in the IP Phone, you have to click the Save button. After you click the Save button, the IP Phone will automatically restart and the new setting will effect.
Firmware Upgrade In Firmware Upgrade function you can update new firmware via HTTP or TFTP methods in this page. You can ugrade the firmware by the following steps: Select the upgrade method and the firmware code type, AP or DSP code. Click the “Browse” button in the right side of the File Location or you can type the correct path and the filename in File Location blank. Select the correct file you want to download to the device then click the Update button.
Field Descriptions Update via There are TFTP/ FTP and HTTP three ways to provide the auto upgrade function. TFTP Server Input the TFTP Server address, and it could input the IP or Domain Name form. HTTP Server Input the HTTP Server address, and it could input the IP or Domain Name form. HTTP File Path Set up the file path. FTP Server Input the FTP Server address, and it could input the IP or Domain Name form. FTP Username The login username.
and time. - Scheduling: The machine will follow the scheduling date and time to check the new firmware. Scheduling (Date) The machine will check the new firmware between the time range by random. Automatic Update There are Notify only and Automatic ways to update. - Notify only: If there are new firmware, the IP Phone will send the “Be Be Be” sounds when pick up the handset to prompt there are new firmware. - Automatic: The device will carry firmware update out automatically.
Appendix A Voice communications There are several ways to make calls to desired destination in IP Phone. In this section, we’ll lead you step by step to establish your first voice communication via keypad and web browsers operations. Case 1: Voice communication via IP PBX system _ IPX-2000 (Auto-config) In the following sample, we’ll introduce how to integrate the IP Phone with our IP PBX system IPX-2000 via Auto-config feature.
In most case, insert the optional code 151 and the value=http://192.168.0.50/tftpboot/ Note: the 192.168.0.50 is the IP address of IPX-2000 STEP 2: Please browse to the Device Æ IP Phone menu and create new device. And press the EDIT button for set up the Auto Config configuration. STEP 3: Please fill out the Vendor Prefix code and MAC Address of IP Phone.
STEP 5: After setting up the parameters, please browse to the Service Æ IP PBX service menu, and press RELOAD of IP PBX configuration reload selection for activating the settings. Machine configuration on the VIP-154T: STEP 6: Please log in VIP-154T A via web browser, browse to the Advanced Settings menu. In the setting page, please browse to the Auto-config page, and select to IP-PBX choice of the Auto Configuration features for IP PBX system.
STEP 7: After enabled the Auto-config feature, the VIP-154T A shall be able to obtain IP address and SIP extension information from IP PBX system IPX-2000 information. To verify the auto-config results, you may check the extension number from LCD display assigned by IPX-2000. STEP 8 Repeat the same configuration steps on VIP-154T B, and check if the VIP-154T B is successfully registered with the IPX-2000 as one of the IP extensions.
Operation steps: Pick up the VIP-154T A, you should be able to hear the dial tone, press the keypad: 192*168*0*2# shall be able to connect to the VIP-154T B. Then the phone in 192.168.0.2 should ring. Please repeat the same dialing steps on VIP-154T B to establish the first voice communication from the second VIP-154T y L Hint y If the IP address of the remote calling party is known, you may directly make calls via its IP address and end with an “#”.
STEP 3: Repeat the same configuration steps on VIP-154T B, and check the machine registration status, make sure the registrations are completed. Test the scenario: To verify the VoIP communication, you may make calls from SIP client (VIP-154T A) 1001 to the number 1002 (VIP-154T B) or reversely make calls from SIP client (VIP-154T B) 1002 to the number 1001 (VIP-154T A ) Case 4: Call Forward Feature_Example 1 In the following samples, we’ll introduce the Call Forward Feature applications.
Machine configuration on the VIP-154T: STEP 1: Please log in VIP-154T_A via web browser, browse to the Phone Settings menu and select the Call Forward config menu.
After 2~3 seconds, the LCD screen will show below: 10-19 17:20 AF 2002 Test the scenario: VIP-154T_C pick up the telephone and dial the number 1001(VIP-154T_A), because VIP-154T_A had set up All Forward function to the number 2002(VIP-154T_B), so the number 2002(VIP-154T_B) will ring up then it pick up the telephone and communication with the number 3003(VIP-154T_C). Case 5: Call Forward Feature_Example 2 In this example, there are one VIP-154NT and two VIP-154T register to IPX-300.
STEP 2: After set up completed and reboot machine, the LCD screen will show below: 10-19 17:20 # Forward # After 2~3 seconds, the LCD screen will show below: 10-19 17:20 AF -11112222 Test the scenario: VIP-154T_C pick up the telephone and dial the number 1001(VIP-154NT_A), because VIP-154NT_A had set up All Forward function to the PSTN Phone Number 11112222, so the PSTN Phone Number 11112222 will ring up then it pick up the telephone and communication with the number 3003(VIP-154T_C).
Machine configuration on the VIP-154NT: STEP 1: Please log in VIP-154NT_A via web browser, browse to the Phone Settings menu and select the Call Forward config menu.
10-19 17:20 # Forward # After 2~3 seconds, the LCD screen will show below: 10-19 17:20 AF 2002 Test the scenario: PSTN Phone Number 11112222 pick up the telephone and dial the PSTN Phone Number 33334444(VIP-154NT_A), because VIP-154NT_A had set up All Forward function to the number 2002(VIP-154T_B), so the number 2002(VIP-154T_B) will ring up then it pick up the telephone and communication with the PSTN Phone Number 11112222.
STEP 2: After set up completed and reboot machine, the LCD screen will show below: 10-19 17:20 # Forward # After 2~3 seconds, the LCD screen will show below: 10-19 17:20 AF 192.168.0.2 Test the scenario: VIP-154T_C pick up the telephone and dial the IP Address 192.168.0.1(VIP-154T_A), because VIP-154T_A had set up All Forward function to the IP Address 192.168.0.2(VIP-154T_B), so the IP Address 192.168.0.2 (VIP-154T_B) will ring up then it pick up the telephone and communication with the VIP-154T_C.
Machine configuration on the VIP-154NT: STEP 1: Please log in VIP-154NT_A via web browser, browse to the Phone Settings menu and select the Call Forward config menu. In the setting page, please disable All Forward function, and then the sample configuration screen is shown below: STEP 2: Please log in VIP-154NT_A via web browser, browse to the Phone Settings menu and select the Auto Answer config menu.
Test the scenario: VIP-154T_C pick up the telephone and dial the IP Address 192.168.0.1(VIP-154NT_A), VIP-154NT will ring up but doesn’t answer the call. After 3 rings, the VIP-154T_C will hear the prompt sounds then input the password 123#. VIP-154T_C will hear the dial tone from PSTN line then input Phone Number 11112222. The Phone Number 11112222 will ring up then it pick up the telephone and communication with the VIP-154T_C.
Please log in VIP-154NT_A via web browser, browse to the Phone Settings menu and select the Auto Answer config menu. In the setting page, please enable the Auto Answer and PIN Code Enabled function, and then the sample configuration screen is shown below: STEP 2: Please log in VIP-154NT_A via web browser, browse to the Phone Book menu and select the Speed Dial Settings config menu. In the setting page, please add a speed dial number for dial to IP address 192.168.0.
Appendix B The method of operation guide In this section, we’ll introduce the features method of operation, and lead you step by step to establish these features. Call Transfer A. Blind Transfer 1. B call to A and they are in the process of conversation. 2. A press “Transfer” button to hold the conversation with B, and input the number of C (Follow by the “#” key). 3. C will ring up, and A hang up the handset. 4. C picks up the handset and conversation with B. B. Attendant Transfer 1.
the switch code. Realm switch code: 1*: Realm 1 2*: Realm 2 3*: Realm 3 For example: The default is realm 1, input the 2* (Follow by the # key) from keypad and hang up the telephone set. It will switch to realm 2, and it can make the SIP calls via realm 2.
Appendix C VIP-154T / VIP-154PT / VIP-154NT Specifications Product Model Hardware LAN PC Telephone Interface SIP IP Phone VIP-154T SIP PoE IP Phone VIP-154PT SIP IP Phone with PSTN connectivity VIP-154NT 1 x 10/100Mbps RJ-45 port Power Over Ethernet 802.3af compliant at VIP-154PT 1 x 10/100Mbps RJ-45 port 1 x RJ-11 --PSTN connectivity at VIP-154NT 2 x 16 characters Full duplex hands free speaker phone LCD display Speaker Protocols and Standard Standard SIP 2.
