802.
Copyright Copyright (C) 2005 PLANET Technology Corp. All rights reserved. The products and programs described in this User’s Manual are licensed products of PLANET Technology, This User’s Manual contains proprietary information protected by copyright, and this User’s Manual and all accompanying hardware, software, and documentation are copyrighted.
Revision User’s Manual for PLANET 802.11g SIP VoIP Router: Model: VIP-462DG Rev: 1.0 (Sept. 2005) Part No.
TABLE OF CONTENTS Chapter 1 Introduction .......................................................................... 6 Overview............................................................................................................................6 Package Content ...............................................................................................................7 Physical Details .................................................................................................................
Traffic Statistics........................................................................................................29 NAT Settings....................................................................................................................29 Address Mapping......................................................................................................30 Virtual Server............................................................................................................
Chapter 1 Introduction 1 Overview Combining cutting edge Internet telephony and router manufacturing experience, PLANET proudly introduces the newest member of the PLANET VoIP gateway family: the VIP-462DG. To bring the most satisfaction to customers, the VIP-462DG, not only provides quality voice communications, wired/wireless Internet sharing capabilities, but also offers DECT interface for daily wireless telephony communications.
DECT Features • DECT & GAP Compatible • Base can register up to 8 Handsets • Intercom call during external call, Call transfer between • handsets , three-way telephone meeting • CID 50 locations • Redial memory: 3 locations, 20 digits • Adjustable ringer volume & melody • 100 hours standby time, 8 hours talk time • Hands-Free, Mute function • Call duration time meter • Transmitted distance: up to 50m indoor / up to 300m outdoor Package Content The contents of your product should contain
Physical Details The following figure illustrates the front/rear panel of VIP-462DG.
LED Display & Button LED Indicators PWR Descriptions Light: power on, normal operaion Blink: firmware loading Off: power off or failure WAN Light: connection is active Blink: data transmitting or receiving Off: connection is not established VoIP Light: SIP proxy registration is successful Blink: SIP proxy registration is unsuccessful Off: SIP proxy registration is disable WLAN Light: connection is active LAN 1 ~ LAN 4 Light: connection is active Blink: data transmitting or receiving Off: connection
Back Panels Descriptions DC12V Power Adapter connecter RESET (Reboot) Press for one second to reset the device or press for 5 seconds to reset to the factory default. WAN 10/100Mbps RJ-45 connector connect to ADSL or cable modem LAN 1 ~ LAN 4 10/100Mbps RJ-45 connector connect to PC or local switch/hub.
Keypad and button definition on DCT-100 Descriptions INT Intercom conversation mode Adjust the volume level during the conversation and menu selection on the LCD display Last Number Redial Hang on / up telephone or pressing until to open /close speaker C Cancel and Clear R Power on / off Number 0 –9 and # The function is as the same as the general phone set ** Press ** to switch to PSTN DCT-100 installation The three rechargeable Ni-MH batteries (AAA size) come with your phone.
ÍNote ÍNote z This phone won't work by itself. It should be registered to the main base unit inside the VIP-320. Before initial using, it should be charged for 24 hours. z z Reversing the orientation may damage the handset. z The battery needs to be replaced if it does not recover its full storage capacity after recharging. z When replacing batteries, always use good quality Ni-MH re-chargeable AAA size batteries. z Never use other batteries or conventional alkaline batteries.
Chapter 2 Preparations & Installation 2 Physical Installation Requirement This chapter illustrates basic installation of VIP-462DG • Network cables. Use standard 10/100BaseT network (UTP) cables with RJ45 connectors. • TCP/IP protocol must be installed on all PCs.
ÍNote Please locate your PC in the same network segment (192.168.0.x) of VIP-462DG. If you’re not familiar with TCP/IP, please refer to related chapter on user’s manual CD or consult your network administrator for proper network configurations. LAN/WAN Interface quick configurations Nature of PLANET VIP-462DG is an IP Sharing (NAT) device, it comes with two default IP addresses, and default LAN side IP address is “192.168.0.1”, default WAN side IP address is “172.16.0.1”.
WAN IP address configuration via web configuration interface Execute your web browser, and type http://172.16.0.1 in the adddress bar. If you’re using WAN port login the VIP-462DG, please be sure to check if the “Rermote Management” is enabled in machine.
3 Chapter 3 Network Service Configurations Configuring and monitoring your VIP-462DG from web browser The VIP-462DG integrates a web-based graphical user interface that can cover most configurations and machine status monitoring. Via standard, web browser, you can configure and check machine status from anywhere around the world. Overview on the web interface of VIP-462DG With web graphical user interface, you may have: More comprehensive setting feels than traditional command line interface.
VIP-462DG main page 17
Chapter 4 4 General Configurations System Settings This page includes all the basic configuration tools for the product, such as options to control management access. Time Zone Set the proper time zone and the configure time server for the VIP-462DG. When you enable “Automatic Time Server Maintenance” option you will need to configure time servers, use the options below to set the primary and secondary NTP servers in your area Password Settings Set the password of the user.
Remote Management The "Remote Management" feature can restrict remote user login from the WAN port. The IP setting of "0.0.0.0" allows user from any IP address to remote logged in to the device. When the 'Enabled" is not checked, remote login is disabled. L Hint The remote user can login using WAN IP. The default port number is 8080.
Dynamic IP Under this mode, VIP-462DG enables DHCP client to get IP address automatically from your service provider. The Host Name is optional, but may be required by some Service Provider’s. The default MAC address is set to the WAN’s physical interface on the VIP-462DG. If required by service provider, you use the “Clone MAC Address” button to copy the MAC address of the Network Interface Card installed in your PC and replace the WAN MAC address with this MAC address.
Static IP If your service provider has assigned a fixed IP address, enter the assigned IP address, subnet mask and the gateway address provided. DNS Most service providers provide a DNS server for speed and convenience. If there is a DNS server that you would rather use, you need to specify the IP address here. If you are static IP user, you must specify DNS server IP. When primary DNS does not work, system will use secondary DNS.
LAN Settings The VIP-462DG needs to have an IP address of the local network. You can enable DHCP to dynamically allocate IP addresses to your client PCs. When DHCP server is enabled, you need to enter the IP address range for the local hosts. The domain name field is empty in most case. In some special ISP need input domain name field. Wireless Setting VIP-462DG can be quickly configured as a wireless access point for roaming clients by setting the service set identifier (SSID) and channel number.
Channel and SSID This page allows you to define SSID, Transmission Rate, Basic Rate and Channel ID for wireless connection. In the wireless environment, VIP-462DG can also act as a wireless access point. These parameters are used for the mobile stations to connect to this access point. Security VIP-462DG can transmit your data security over the wireless network. Matching security mechanisms must be setup on your VIP-462DG and wireless client devices.
WPA WPA is a security enhancement that strongly increases the level of data protection and access control for existing wireless LAN. Matching authentication and encryption methods must be setup on your VIP-462DG and wireless client devices to use WPA.
Chapter 5 System Configurations 5 VoIP Settings The section includes the entire VoIP configuration for VIP-462DG. Port Setting This page sets up the phone number and username/password for SIP server registration. The phone number and username/password must be predefined in SIP Proxy. You can register two VoIP number to VIP-462DG, register one number for analog telephone set and the other number for DECT handset.
SIP Setting This page defines the SIP parameters, in the SIP Parameters setting, we need to set SIP domain and SIP Proxy IP address. The default register expire time is 1800 second. So the system must reregister to SIP proxy again within register expire time. VoIP adanced setting This page allows you to configure advanced VoIP features including voice Codec configuration.
Port advanced Setting and register DECT handset This page allows you adjust the parameter of voice channel to achieve better sound quality. In this page also provide DECT setting for you to paging and register new DECT handset. Qos Settings The bandwidth gap between LAN and WAN may significantly degrade performance of critical network applications, such as VoIP, gaming and VPN. This QoS function allows users to classify traffic of application and provide them with differentiated services (Difffserv).
Traffic mapping Up to 16 rules can be defined to classify traffic into Diffserv forwarding groups and outgoing VCs. Edit Traffic class This page is for user to specify a classify rule, First, define the class by traffic type and the local and remote addresses, then set the Diffserv forwarding group this class is mapped to, finally select the outgoing VC that traffic of this class would be routed to.
Traffic Statistics This page shows the WAN outbound traffic statistics of all of the Diffserv forwarding groups in the last 12 hours (automatically updated every 5 mins). NAT Settings Network Address translation (NAT) allows multipleusers at your local site to access the Internet through a signal public IP address or multiple public IP address.
Address Mapping VIP-462DG supports multiple global IP addresses. It allows IP addresses used in a private local network to be mapped to one or more addresses used in the public, global Internet. This page allows user to enter up to 10 addresses mapping between a set of private IP addresses and one global IP address. After setting, VIP-462DG will map the set of private IP addresses to the global IP address when accessing to the Internet.
Some of the popular applications and protocol/port numbers mapping are defined below: Application Protocol Port Number Telnet TCP 23 FTP TCP 21 SMTP TCP 25 POP3 TCP 110 H.
Special Application Some applications require multiple connections, such as Internet gaming, video conferencing, Internet telephony and others. These applications cannot work when Network Address Translation (NAT) is enabled.
Firewall Setting VIP-462DG provides extensive firewall protection by restricting connection parameters to limit the risk of hacker attack, and defending against a wide array of common attacks. When firewall is enabled, extra checking will be performed for each packets passing through the device, the performance of the device will be greatly affected.
This page allows users to define service limitation of client PC, including IP address, service type and scheduling rule criteria. For URL blocking function, you need config URL address first in "URL Blocking Site" page. For scheduling function, you also need config schedule rule first in "Schedule Rule" page. As shown above, user enter Client PC Description (Notebook), and it’s IP address (192.168.0.100),and select service name “WWW” and “E-mail Sending”, and press “OK” button.
MAC Filter User can enter up to 32 MAC address, the PCs with these MAC addresses will not be permitted to access Internet. URL Blocking You can block access to certain Web sites from a particular PC by entering either a full URL address or just a keyword of the Web site. To specify the particular PC, go back to the "Access Control" page and check the box for "Http with URL Blocking" in the "Normal Filtering Table".
As shown above, all of the URL with ”violence” pattern cannot be accessed. The users within LAN site cannot access to any web-site with “violence” in its URL address. User can enter up to 32 MAC address, the PCs with these MAC addresses will not be permitted to access Internet. Schedule Rule This page allows user to define schedule rule for use in Access Control page. User press “Add Schedule Rule” to add schedule name and effective time period.
As shown above, we defined a schedule rule called “Office Hour”, the active time period is Monday to Friday, 9:00 am to 5:00 pm. After pressing “OK” button, the following page will show up: Then when we go to “Access Control” page, select “Add PC”, in the bottom of the page “Access Control Add PC”, the scheduling rule will show “Office Hour”, as shown below: If we setup the PC of RDM department in our company (IP address 192.168.0.101 to 192.168.0.
Intrusion Detection Features: SPI and Anti-DoS Firewall Activate SPI and Anti-DoS protection Protection RIP Defect Reject the RIP packets from WAN Discard PING from WAN Reject all the PING request to the WAN port When hacker tries to attack, VIP-462DG can send e-mail alert to the specified user. Enter related e-mail information such as e-mail address and SMTP server. Some e-mail service providers require user to enter POP3 information when trying to send e-mail.
UPnP The Universal Plug and Play architecture offers pervasive peer-to-peer network connectivity of PCs of all form factors, intelligent appliances, and wireless devices. UPnP enables seamless proximity network in addition to control and data transfer among networked devices in the home, office and everywhere in between. Enable the UPnP to support Windows XP network application. For example, MS Messager. If user want to use Windows XP messager application, you must enable this feature.
Tools The tools feature provided by VIP-462DG includes configuration tools – save /restore configuration and restore to factory defaults, system log, firmware upgrade and reset. Configuration Tools The configuration tools includes backup, restore and restore to factory defaults. The “Backup” tool save the VIP-462DG’s current configuration to a file named “backup_config.bin” on your PC. Users can then use “Restore” tool to restore the saved configuration to the VIP-462DG.
Reset In the event that the system stops responding correctly or in some way stops functioning, you can perform a reset. Your settings will not be changed. To perform the reset, click on the “APPLY” button below. You will be asked to confirm your decision. The reset will be complete when the power light stops blinking Status The status page displays the status of the system, including the connection status of the interfaces, firmware and hardware version numbers, system log and DHCP client information.
Device Status The Device Status page displays the current setting of this device, including IP address, Subnet mask, DHCP server, Firewall and UPnP. Security Log This page provides the system security log record when device boot, including user login/logout, hack attach, PPPoE connection, NTP connection, Get IP from DHCP. These records can be saved to host PC. User also can clear all security records in Security log window and press “Refresh” button to update current security records.
VoIP Status This page displays the gateway status, including Port type, port Status, time information of each call and Destination. This page also displays SIP proxy registration status. User must make sure SIP proxy registration is successful. User can press “Refresh” button to update current VoIP status.
Appendix A A VIP-462DG Specifications Product Model Hardware WAN PC WLAN PSTN Phone DECT Protocols and Standard Standard Voice codec Voice Standard 802.11g SIP DECT VoIP Router VIP-462DG 1 x 10/100Mbps RJ-45 port 4 x 10/100Mbps RJ-45 port IEEE 802.11b /802.11g compatible 1 x RJ-11 connection 1 x RJ-11 connection 1 x DECT GAP compatible base SIP 2.0 (RFC3261) G.723.1 (6.3k/5.3k), G.729A, G.
