Dual Band 802.
Copyright Copyright 2022 by PLANET Technology Corp. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of PLANET.
FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure set forth for an uncontrolled environment. In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antenna shall not be less than 20 cm (8 inches) during normal operation. CE Compliance Statement This device meets the RED directive 2014/53/EU of EU requirements on the limitation of exposure of the general public to electromagnetic fields by way of health protection.
Revision User Manual of PLANET 1200Mbps 802.11ac Dual Band Wireless Gigabit Router Model: WDRT-1800AX Rev: 1.0 (April, 2022) Part No. EM- WDRT-1800AX_v1.
CONTENTS Chapter 1. Product Introduction......................................................................................... 1 Package Contents ........................................................................................................................ 1 Product Description ..................................................................................................................... 2 Product Features ...................................................................................
Advanced..................................................................................................................................... 43 5.1.11 Internet control (Flow Control) ................................................................................ 43 5.1.12 DDNS ...................................................................................................................... 44 5.1.13 ALG service ...........................................................................................
iPhone / iPod Touch / iPad ......................................................................................................... 76 Appendix A: Specifications ..............................................................................................
User Manual of WDRT-1800AX Chapter 1. Product Introduction Package Contents Thank you for choosing PLANET WDRT-1800AX. Before installing the router, please verify the contents inside the package box. WDRT-1800AX Wireless Router Quick Installation Guide Power Adapter Ethernet Cable RJ45 Cable 12V DC, 1A If there is any item missing or damaged, please contact the seller immediately.
User Manual of WDRT-1800AX Product Description Amazing Next-generation Wireless High-speed Connection PLANET WDAP-1800AX Dual Band 802.11ax 1800Mbps Wireless Gigabit Router, supporting MU-MIMO, Wave 2.0, OFDMA and EasyMesh technology, provides a maximum wireless speed of 1200Mbps in the 5GHz band and 600Mbps in the 2.4GHz band. The maximum number of client users is up to 64, ensuring more secure and robust connectivity with the adoption of Wi-Fi 6 technology.
User Manual of WDRT-1800AX OFDMA (Orthogonal Frequency Division Multiple Access) OFDMA is a multi-user evolved version based on OFDM digital modulation technology. In the Wi-Fi 6 (802.11ax) standard, the main function of OFDMA is to improve network performance. Orthogonal frequency division multiple access (OFDMA) enables users to simultaneously operate in the same channel and therefore improves efficiency, latency, and throughput.
User Manual of WDRT-1800AX BSS (Basic Service Set) Coloring The BSS color is a numerical identifier of the BSS. 802.11ax radios are able to differentiate between BSSs using BSS color identifier when other radios transmit on the same channel. If the color is the same, this is considered to be an intra-BSS frame transmission. In other words, the transmitting radio belongs to the same BSS as the receiver.
User Manual of WDRT-1800AX Easy Installation with EasyMesh Function Wi-Fi EasyMesh provides a standards-based method for implementing multi-access point (AP) Wi-Fi networks. It not only has the advantages of easy-to-use and self-adjusting Wi-Fi, but also has interactive Wi-Fi certified equipment that leads to the advantage of improved equipment selection flexibility.
User Manual of WDRT-1800AX Product Features IEEE Compliant Wireless LAN and Wired LAN Compliant with the IEEE 802.11a/b/g/n/ac/ax wireless technology Equipped with 1 WAN and 4 LANs with 10/100/1000Mbps RJ45 ports, and auto MDI/MDI-X RF Interface Characteristics 802.11ax 2T2R architecture with data rate of up to 1800Mbps (600Mbps in 2.
User Manual of WDRT-1800AX Product Specifications Product WDRT-1800AX Hardware Specifications WAN Port: 1 x 10/100/1000 Mbps auto MDI/MDI-X RJ45 port Interface LAN Port: 4 x 10/100/1000 Mbps auto MDI/MDI-X RJ45 port (LAN 1~4) Four external 7dBi high gain omnidirectional antennas (2.4GHz x 2, 5GHz x Antenna 2) 1 x WPS/reset button Button Press for about 1 second to enable WPS function. Press for over 5 seconds to reset the device to factory default. PWR x 1 LAN x 4 LED Indicators WAN x 1 WLAN (2.
User Manual of WDRT-1800AX 2.4GHz 11b 11Mbps: 22dBm 11g 6Mbps: 21dBm 11g 54Mbps: 20dBm 11n MCS0-HT20: 21dBm 11n MCS7-HT20: 19dBm 11ax MCS11-HE20: 16dBm 11n MCS7-HT40: 19dBm 11ax MCS9-VHT40: 17dBm Receive Sensitivity 11ax MCS11-HESU40: 16dBm 5GHz 11a 6Mbps: 21dBm 11a 54Mbps: 19dBm 11ac MCS8-VHT20: 17dBm 11ax MCS11-HE-SU20: 16dBm 11ac MCS9-VHT40: 17dBm 11ax MCS11-HE-SU40: 16dBm 11ac MCS9-VHT80:17dBm 11ax MCS11-HE-SU80: 16dBm 2.
User Manual of WDRT-1800AX 11ac MCS9-VHT40: -63 dBm 11ax MCS11-HE-HESU40: 58dBm 11ac MCS9-VHT80: -58 dBm 11ax MCS11-HE-HESU80: 54dBm Transmit Power Control Low, Medium, High Wireless Management Features Encryption Security WPA/WPA2/WPA3 Wireless MAC address filtering Wireless Security Supports WPS (Wi-Fi Protected Setup ) Supports dual-SSID (2.4GHz and 5GHz) Wireless Advanced Supports guest network 2.4GHz wireless: 32 Max.
User Manual of WDRT-1800AX IEEE 802.3u 100BASE-TX IEEE 802.3ab 1000BASE-T IEEE 802.3x flow control IEEE 802.11k, 802.11v, and 802.11r 802.3ax: OFDMA (BPSK / QPSK / 16QAM / 64QAM / 256QAM/1024QAM) 802.11ac: OFDM (BPSK / QPSK / 16QAM / 64QAM / 256QAM) Modulation Type 802.11a/g/n: OFDM (BPSK / QPSK / 16QAM / 64QAM) 802.
User Manual of WDRT-1800AX Chapter 2. Hardware Installation Please follow the instructions below to connect the WDRT-1800AX to the existing network devices and your computers.
User Manual of WDRT-1800AX 2.1.1 Front LED The front LED provides a simple interface monitoring the router. Figure 2-3 shows the front LED of the WDRT-1800AX. Front LED Figure 2-3 WDRT-1800AX Top View 2.1.2 LED Indications The LEDs on the front panel indicate instant status of port links, wireless data activity and system power, and help monitor and troubleshoot when needed. Figure 2-3 and Table 2-1 show the LED indications of the Wireless Router.
User Manual of WDRT-1800AX 2.1.3 Rear Panel The rear panel provides the physical connectors connected to the power adapter and any other network device. Figure 2-4 shows the rear panel of the WDRT-1800AX.
User Manual of WDRT-1800AX Chapter 3. Connecting to the Router System Requirements Broadband Internet Access Service (Cable/xDSL/Ethernet connection) One Cable/xDSL Modem that has an RJ45 connector (not necessary if the Router is connected directly to the Ethernet.
User Manual of WDRT-1800AX Figure 3-1 Hardware Installation of the WDRT-1800AX Wireless Router Step 4. Connect the power adapter to the power socket on the Router, and the other end into an electrical outlet. Then power on the Router. Step 5. Power on your PC and Cable/xDSL Modem.
User Manual of WDRT-1800AX Chapter 4. Quick Installation Guide This chapter will show you how to configure the basic functions of your Wireless Router using Quick Setup within minutes. A computer with wired Ethernet connection to the Wireless Router is required for the first-time configuration. Manual Network Setup - TCP/IP Configuration The default IP address of the Wireless Router is 192.168.1.1 and the default Subnet Mask is 255.255.255.0.
User Manual of WDRT-1800AX 2) Under the Network and Internet icon, click on the View network status and tasks. And then click Change adapter settings. Figure 4-1 Change Adapter Settings 3) Right-click on the Wireless Network Connection, and select Properties in the appearing window.
User Manual of WDRT-1800AX 4) In the prompt window shown below, double-click on the Internet Protocol Version 4 (TCP/IPv4). Figure 4-3 TCP/IP Setting 5) Choose Obtain an IP address automatically, and Obtain DNS server address automatically as shown in the figure below. Then click OK to save your settings.
User Manual of WDRT-1800AX Figure 4-4 Obtain an IP Address Automatically 4.1.2 Configuring the IP Address Manually Summary: Set up the TCP/IP Protocol for your PC. Configure the network parameters. The IP address is 192.168.1.xxx ("xxx" is any number from 2 to 254), Subnet Mask is 255.255.255.0, and Gateway is 192.168.1.1 (The Router's default IP address) If you are sure the DHCP server of Wireless Router is disabled, you can configure the IP address manually.
User Manual of WDRT-1800AX Figure 4-5 IP and DNS Server Addresses Now, you can run the Ping command in the command prompt to verify the network connection between your PC and the Router. The following example is in Windows 7 OS. Please follow the steps below: 1. Click on Start 2. Type “cmd” in the Search box.
User Manual of WDRT-1800AX 3. Open a command prompt, and type ping 192.168.1.1, and then press Enter. If the result displayed is similar to Figure 4-7, it means the connection between your PC and the Router has been established well. Figure 4-7 Successful Ping Command If the result displayed is similar to Figure 4-8, it means the connection between your PC and the Router has failed.
User Manual of WDRT-1800AX If the address is 0.0.0.0, check your adapter installation, security settings, and the settings on your router. Some firewall software programs may block a DHCP request on newly installed adapters. If the Router's IP address is 192.168.1.1, your PC's IP address must be within the range of 192.168.1.2 ~ 192.168.1.254.
User Manual of WDRT-1800AX Starting Setup in the Web UI It is easy to configure and manage the WDRT-1800AX with the web browser. Step 1. To access the configuration utility, open a web-browser and enter the default IP address http://192.168.1.1 in the web address field of the browser. Figure 4-9 Login the Router After a moment, a login window will appear. Enter admin for the User Name and Password, both in lower case letters. Then click the Log In button or press the Enter key.
User Manual of WDRT-1800AX After entering the password, the Wizard Setup page screen appears as shown in Figure 4-11 . You can configure the router by yourself, and the default WAN setting is “Dynamic”. Figure 4-11 Configure the WAN setting. Step 2. Choose “Next” and please enter the Wi-Fi Password. Then click Next button. Figure 4-12 Wi-Fi Settings Step 3. Please enter the Device new Password. Then click the Confirm button.
User Manual of WDRT-1800AX Figure 4-14 Device Password configuration Step 4. Click the “Enter the management page” button to enter the main interface of the Wi-Fi router to further set up the W-Fi router. Figure 4-15 Step 4.
User Manual of WDRT-1800AX Chapter 5. Configuring the Router This chapter delivers a detailed presentation of router’s functions and features under main menus shown below, allowing you to manage the router with ease. Figure 5-1 Router’s Functions Router status On this page, you can view information about the Internet status and connection state of the WDRT-1800AX, including Network Status, Equipment connected, Download or Upload speed.
User Manual of WDRT-1800AX Figure 5-2 Network connection state Wizard setting When the device that has just been shipped from the factory enters the web management, you can go to the Wizard setting on the management page. Figure 5-3 Wizard setting If you have installed PPP software such as WinPoET (from Earthlink) or Enternet (from PacBell), then you have PPPoE. Select Yes. After selecting Yes and configuring your router, you will not need to run the PPP software on your PC to connect to the Internet.
User Manual of WDRT-1800AX 5.1.2 Mode In this part, you can check your current Internet connection settings. You can also modify the settings according to the service information provided by your ISP. Dynamic Choose “Dynamic IP (DHCP)” and the router will automatically obtain IP addresses, subnet masks and gateway addresses from your ISP.
User Manual of WDRT-1800AX Object Description Enter the WAN IP address provided by your ISP. Inquire your ISP if IP Address you are not clear. Subnet Mask Enter WAN Subnet Mask provided by your ISP. Gateway Enter the WAN Gateway address provided by your ISP. DNS1 Enter the necessary DNS address provided by your ISP. PPPoE Select PPPoE, if your ISP is using a PPPoE connection and provides you with PPPoE user name and password information.
User Manual of WDRT-1800AX Click Enable to check your Internet connection, and click Router status on the right of the page. After the connection succeeds, the screen will display as follows. Here we take Dynamic IP as an example. Figure 5-8 PPPoE Internet setup 5.1.3 Advanced Please follow the instructions on the 5.2.2 Mode to continue the configuration. Press the button for advanced settings. 1) If Dynamic IP is chosen, you need to select whether to clone the MAC address.
User Manual of WDRT-1800AX Figure 5-9 Advanced Dynamic IP Object Description DNS1 Enter the necessary DNS address provided by your ISP. DNS2 Enter the secondary DNS address provided by your ISP MTU Maximum Transmission Unit. Default is 1500 MAC clone Enable to clone the MAC address 2) If Static IPis chosen, enter the information provided by your ISP in the corresponding fields.
User Manual of WDRT-1800AX Figure 5-10 Advanced Static IP Object Description Enter the WAN IP address provided by your ISP. Inquire your ISP if IP Address you are not clear. Subnet Mask Enter WAN Subnet Mask provided by your ISP. Gateway Enter the WAN Gateway address provided by your ISP. DNS1 Enter the necessary DNS address provided by your ISP. DNS2 Enter the secondary DNS address provided by your ISP MTU Maximum Transmission Unit.
User Manual of WDRT-1800AX Figure 5-11 Advanced PPPoE Object Description Account Enter the account provided by your ISP. Password Enter the password provided by your ISP. Enter the necessary DNS address provided by your ISP. DNS1 Default is 8.8.8.8 DNS2 Enter the secondary DNS address provided by your ISP MTU Maximum Transmission Unit.
User Manual of WDRT-1800AX Figure 5-12 2.4G Wi-Fi name and password Object Switch Description Click the button next to switch to switch on and off the Wi-Fi. Set a name (SSID) for your wireless network. The ID of the wireless network. User can access the wireless network through Wi-Fi Name (SSID) it only. However, if you switch to Client Mode, this field becomes the SSID of the AP you want to connect with. Default: PLANET_2.
User Manual of WDRT-1800AX connect to the WDRT-1800AX. BandWidth Select a proper channel bandwidth to enhance wireless performance. Default is 40/20MHz Auto 5.1.5 5G Wi-Fi name and password Click Wireless5G Wi-Fi name and password, and then config wireless is shown in the following parameter: Figure 5-13 5G Wi-Fi name and password Object Switch Description Click the button next to switch to switch on and off the Wi-Fi. Set a name (SSID) for your wireless network. The ID of the wireless network.
User Manual of WDRT-1800AX For optimal wireless performance, you may select the least interferential channel. It is advisable that you select the best Channel possible channel for your wireless network to operate on from the drop-down list. Signal There are three signal modes to choose from. Default is High. Set the wireless mode to which you need. Default is “802.11 ax”. It is strongly recommended that you set the Band to “802.11 ax”, 802.11 Mode and all of 802.11ac and 802.
User Manual of WDRT-1800AX 5.1.7 WISP (Wireless Relay) Turn on WISP and select the operation mode you need, and then press the "Refresh" button to scan the Wi-Fi that you need to be relayed. After successful, the router will restart. After the router restarts, some functions cannot be used. If you want to use all the functions, please switch to the router mode. Please refer to the FAQs on how to switch to the router mode.
User Manual of WDRT-1800AX Figure 5-16 Repeater 5.1.8 WPS WPS (Wi-Fi Protected Setup) is designed to ease setup of security Wi-Fi networks and subsequently network management. The WPS enables the PC with WPS function to connect to the wireless network of the AP without setting any parameters, such as SSID, security mode, or password. 1) Choose Connect WPS on your device. 2) Click the WPS button ”PBC” on the web management or HW button on the rear panel.
User Manual of WDRT-1800AX Figure 5-17 WPS Guest network This page allows you to configure Wi-Fi Guest Network here and create a guest network as needed. Steps to follow: 1) Enable 2.4GHz Wireless network or 5GHz Wireless network.
User Manual of WDRT-1800AX Object 2.4G Name 5G Name Description Specifies the 2.4G SSID for the current profile. Default: PLANET_2.4G_guest Specifies the 5G SSID for the current profile. Default: PLANET_5G_guest Net password Configure the wireless security of the guest network Wi-Fi. Guest speed Choose a limited speed of guest network. Parental controls This page can help parents control children's Internet time, and protect children's eyesight and health.
User Manual of WDRT-1800AX 4) Or click the "Add" button to define the device's MAC address that needs to be controlled. Figure 5-21 Add devices manually IPv6 5.1.9 IPv6 WANSetting There are two options in IPv6 WANsetting mode, Automatic and PPPoEv6; default is Automatic mode. Please check “Get ipv6 prefix agent”, meaning WAN IPv6 will get a prefix address from IPv6 server.
User Manual of WDRT-1800AX Figure 5-23 IPv6 WANSetting- PPPoEv6 Object Description Mode Select IPv6 WANsetting mode; default is Automatic mode. Account Enter the account provided by your ISP. Password Enter the password provided by your ISP. Address distribution Enable it and WAN IPv6 will get a prefix address from IPv6 server. 5.1.10 IPv6 LAN Setting Configure LAN ports, let IPv6 LAN-address and IPv6 LAN prefix in Automatic mode. You can enable or disable DHCPv6 function .
User Manual of WDRT-1800AX Advanced 5.1.11 Internet control (Flow Control) This page can specify upload and download speeds for some devices. Steps to follow: 1) Go to AdvancedInternet controlTurn on “Hardware speedup” 2) Find your device in the list and turn “ON” speed 3) Enter the speed you need in Download(KB) / Upload(KB) 4) Click Confirm Figure 5-25 Add rule of Internet control (Speed Limit) Object Description Hardware speedup Enable or disable hardware speedup, bandwidth control invalid.
User Manual of WDRT-1800AX Upload(KB) Enter the upstream limited for kbps Speed Enable or disable to limit the speed on the device you select. 5.1.12 DDNS The capability of assigning a fixed host and domain name to a dynamic Internet IP Address. Most ISPs assign a dynamic IP address to the router and you can use this IP address to access your router remotely. However, the IP address can change any time and you don’t know when it will change.
User Manual of WDRT-1800AX Password Enter password for DDNS. If you use Easy DDNS, it is not necessary to do it. 5.1.13 ALG service WDRT-1800AX supports IPSec/L2TP VPN Pass-through. Figure 5-27 ALG service Object Description IPsec Enable or disable IPSec to pass through IPSec communication data. L2TP Enable or disable L2TP to pass through L2TP communication data. 5.1.
User Manual of WDRT-1800AX Figure 5-28 DMZ host setting Object Description DMZ host IP Enter the DMZ host IP address Enable DMZ Enter the DMZ LAN IP. 5.1.15 IP filter Figure 5-29 IP filter Object Description IP Blacklist: Enter the IP that you prohibited rules within the device through.
User Manual of WDRT-1800AX 5.1.
User Manual of WDRT-1800AX 5.1.17 Port filter Port filtering is the practice of allowing or blocking (opening/closing) network packets into or out of a device or the network based on their port number. Blocking network ports with a port filter allows administrators to restrict specific operations such as file transfers through ports used for FTP and torrents. Steps to follow: 1) Advanced Port Filter page 2) Enter the desired port number in the Start Port & End Port fields.
User Manual of WDRT-1800AX 5.1.18 Virtual server After using the router, Internet users cannot access the hosts in the LAN, so they cannot access Web, FTP, Mail and other servers built on the intranet. The virtual server function can realize the mapping of the server of the intranet to the Internet, so as to realize the opening of the server to the outside world.
User Manual of WDRT-1800AX 5.1.19 Firewall (Protect the Network from Cyber Attacks) Firewall protects your home network from DoS attacks that can flood your network with server requests. Follow the steps below to configure DoS protection. Steps to follow: 1) Go to AdvancedFirewall 2) Turn on “prevent flooding attack” 3) If you want to ignore the ping packets from the WAN port,Turn on “anti WAN port ping”.
User Manual of WDRT-1800AX Router 5.1.20 LAN settings Figure 5-34 LAN settings Object IP Address Description Router’s LAN IP. The default is 192.168.1.1. You can change it according to your needs. Mask Router’s LAN subnet mask. DHCP Click the button to enable or disable Router DHCP Server function. Configure the IP address interval that allocated to the terminal. The Starting IP / Ending IP address interval must be on the same network segment as the management IP address of the Router.
User Manual of WDRT-1800AX 5.1.21 Static IP allocation (IP & MAC Binding) IP and MAC Binding is used to bind the IP address of a network device to its MAC address. This will prevent ARP spoofing and other ARP attacks by denying network access to devices in the binding list with matching IP addresses but unrecognized MAC addresses.
User Manual of WDRT-1800AX 5.1.22 Time setting In this interface, user can configure “local time” and “Time zone”. Figure 5-35 Time setting Object Description Local Time Use your local time as your device’s system time. Time Zone Select time zone Enable NTP Select Enable or Disable NTP function Sync with Host Press to sync system time with host server 5.1.
User Manual of WDRT-1800AX Object Description Old Enter the old password New Enter the new password Confirm Enter the new password again 5.1.24 Restart To reboot and reset default settings your WIFI Router. Figure 5-37 Restart and reset Object Description Reboot router Press to reboot the device Factory reset Press to reset the device to default 5.1.25 Software upgrade Upgrade WIFI router needs about four minutes, then WIFI router will auto reboot.
User Manual of WDRT-1800AX Object Description Version Show the current version Firmware Upgrade Press to upgrade firmware via online or local management Upgrade Press to select the firmware file Restore Factory Settings Select to reset the device to default when upgrading firmware 5.1.
User Manual of WDRT-1800AX 5.1.27 Web management On this page, users can modify web language, remote web, turn off LED, Telnet service, and Smart discovery function. Figure 5-40 WEB management Object Description Language English Remote web You can visit web by WAN interface if switched to on. Default is off. Close LED The LED will be turned off if you switch to on. Default is off. Telnet service You can Telnet the router by LAN interface if you switch to on. Default is off.
User Manual of WDRT-1800AX 5.1.28 System log You can get system log information of router operating on this page for diagnosis. Figure 5-41 System log 5.1.
User Manual of WDRT-1800AX Figure 5-42 System state 5.1.30 Equipment mode There are 3 modes that you can configure: Route mode, Bridge mode and Relay mode. The default mode is Route.
User Manual of WDRT-1800AX 5.1.31 Automatic maintenance Here you can set the auto maintenance time and day of the week. For example: User needs to maintain the router at 2 am every day, the configuration is as shown below: Figure 5-43 Automatic maintenance Object Description Restart Enter the automatic maintenance. Restart time Select reboot time for clock and duty by day.
User Manual of WDRT-1800AX TR069 TR069 is a protocol. It provides operators with multiple management methods for easy maintenance of sold products. All of parameters of TR069 are offered by ISP. Step: 1) Go to TR069Turn on 2) You can set the router parameters of the TR069 client (ACS URL address, username, password, periodic notification interval). Figure 5-44 TR069 Object TR069 ON/OFF ACS-URL Description Enable/Disable CWMP protocol URL of ACS. Examples: "https://example.
User Manual of WDRT-1800AX ManagementServer.PeriodicInformInterval" Manual inform Confirm Send inform messages manually Confirm the configuration of TR069 client Wi-Fi Mesh Wi-Fi Mesh network is a new wireless networking solution developed based on Wi-Fi technology. Compared with the traditional wireless network, the transmission distance and mobility of the Wi-Fi Mesh network will be greatly improved, especially if it is compatible with the Wi-Fi function.
User Manual of WDRT-1800AX Chapter 6. FAQs FAQ 1. What can I do if I forgot my wireless password? The default wireless password is printed on the label of the router. If the password has been altered, please connect your computer to the router using an Ethernet cable and follow the steps below: 1. Visit http://192.168.1.1 2. Go to Wireless 2.4G/5G Wi-Fi name and password 3. Retrieve or reset your Wi-Fi password FAQ 2.
User Manual of WDRT-1800AX 3. Firewalls and viruses Sometimes firewalls and antivirus software on your computer can block access to the router and you need to turn them off or replace a device. FAQ 4. I cannot access the Internet even though the configuration is finished. What can I do? 1.Check the physical connection of the WAN interface If the Un insert cable message appears on the router's Internet setup page, it means that the network cable is not inserted correctly.
User Manual of WDRT-1800AX 4.Change router LAN IP address Most Ceres routers use 192.168.11.1/24 as the default LAN IP address, which may conflict with your existing modem/router IP. If so, it will cause you to not be able to access the Internet. We can change the router LAN IP to avoid IP conflict, for example 192.168.88.1 1. Visit http://192.168.1.1 2.
User Manual of WDRT-1800AX Note: After changing the LAN IP address, you need to use the new IP to access the management interface next time. 5.Double-check the Internet Connection Type. 1. Confirm your Internet Connection Type, which can be learned from the ISP. 2. Visit http://192.168.1.1 3. Go to Internet setupMode 4. Select your Internet Connection Type and fill in other parameters with the help of page tips.
User Manual of WDRT-1800AX 6.Your computer might not recognize any DNS server addresses, please manually configure DNS server. 1. Visit http://192.168.1.1 2. Go to RouterLAN settings 3. Enter 8.8.8.8 as DNS1, 8.8.4.4 as DNS2 7.Reset the router to factory default settings and reconfigure the router. 8.Upgrade the firmware of the router. 9.Check the TCP/IP settings on the particular device if all other devices can get Internet from the router.
User Manual of WDRT-1800AX If you can find a wireless network but can't connect, follow these steps: 1. Authentication problem/password mismatch The default wireless password is usually on the label stuck on the back of the device. If the default password is incorrect, please try to restore the factory settings and connect again Note:Wireless passwords are case sensitive 2. Windows cannot connect to xxx/Cannot connect to this network/Connected to this network for too long 1.
User Manual of WDRT-1800AX Fault 2: Relay failed 1) Set according to Fault 1. 2) The main route and the sub-route are too far apart. 3) Confirm that the SSID and password for connecting to the main router are correct 4) Check whether the upper-level router has set MAC filtering. If so, please add it. 5) Factory reset or update the latest firmware FAQ 8.
User Manual of WDRT-1800AX 2) Put the router at a certain height Home routers generally use omnidirectional antennas, which radiate around horizontally and are weaker vertically. Place your router on a table or shelf to better utilize the transmission from the antenna. 3) Stay away from high-power appliances High-power appliances and metal products may cause signal interference. Note that electrical appliances include microwaves, refrigerators, TVs, etc.
User Manual of WDRT-1800AX Chapter 7.
User Manual of WDRT-1800AX Step 4: Enter the encryption key of the Wireless Router (1) The Wireless Network Connection box will appear (2) Enter the encryption key that is configured in section 5.2.2.1 (3) Click the [Connect] button Figure 6-3 Step 5: Check if “Connected” is displayed Figure 6-4 Some laptops are equipped with a “Wireless ON/OFF” switch for the internal wireless LAN. Make sure the hardware wireless switch is switched to the “ON” position.
User Manual of WDRT-1800AX Windows 7/Windows 10 (WLAN AutoConfig) WLAN AutoConfig service is built in Windows 7 for detecting and connecting to wireless network. This built-in wireless network connection tool is similar to wireless zero configuration tool in Windows XP. Step 1: Right-click on the network icon displayed in the system tray Figure 6-5 Step 2: Highlight and select the wireless network (SSID) to connect (1) Select SSID (Take default_2.
User Manual of WDRT-1800AX (2) Enter the encryption key that is configured in section 5.2.2.
User Manual of WDRT-1800AX Mac OS X 10.x Step 1: Right-click on the network icon displayed in the system tray The AirPort Network Connection menu will appear Figure 6-10 Step 2: Highlight and select the wireless network (SSID) to connect (1) Select and SSID (Take PLANET for example) (2) Double-click on the selected SSID Figure 6-11 Step 4: Enter the encryption key of the Wireless Router (1) Enter the encryption key that is configured in section 5.2.2.
User Manual of WDRT-1800AX If you want to connect this Wireless Router in the future, check [Remember this network]. Step 5: Check if the AirPort is connected to the selected wireless network. If “Yes”, then there will be a “check” symbol in the front of the SSID.
User Manual of WDRT-1800AX iPhone / iPod Touch / iPad Step 1: Tap the [Settings] icon displayed in the home screen Figure 6-14 Step 2: Check Wi-Fi setting and select the available wireless network (1) Tap [General] \ [Network] (2) Tap [Wi-Fi] If this is the first time to connect to the Wireless Router, it should show “Not Connected”.
User Manual of WDRT-1800AX Figure 6-16 Step 3: Tap the target wireless network (SSID) in “Choose a Network…” (1) Turn on Wi-Fi by tapping “Wi-Fi” (2) Select SSID Take PLANET for example) Figure 6-17 Step 4: Enter the encryption key of the Wireless Router (1) The password input screen will be displayed (2) Enter the encryption key that is configured in section 5.2.2.
User Manual of WDRT-1800AX Figure 6-18 Step 5: Check if the device is connected to the selected wireless network. If “Yes”, then there will be a “check” symbol in the front of the SSID.
User Manual of WDRT-1800AX Appendix A: Specifications EC Declaration of Conformity English Hereby, PLANET Technology Corporation, declares that this 802.11ac Dual Band Wireless Router is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. Lietuviškai Šiuo PLANET Technology Corporation,, skelbia, kad 802.11ac Dual Band Wireless Router tenkina visus svarbiausius 2014/53/EU direktyvos reikalavimus ir kitas svarbias nuostatas.
