Industrial L2+ 8-Port 10/100/1000T 802.3bt PoE + 2-Port 1G/2.
Table of Contents 1. Package Contents........................................................................................ 3 2. Requirements.............................................................................................. 4 3. Hardware Installation................................................................................... 5 3.1 Wall Mount Installation.......................................................................... 5 3.2 Wall Hanging Installation............................
1. Package Contents Thank you for purchasing PLANET Industrial Wall-mount Managed Gigabit Switch, WGS-5225-8UP2SV. The table below shows the model with the number of ports: Model Name Copper Port Fiber Port 2.4 LCD WGS-5225-8UP2SV 8 x 10/100/1000T 2 x 100/1000/2500X In the following sections, unless specified, the term “Wall-mount Managed Switch” mentioned in this quick installation guide refers to the above model. Open the box of the Wall-mount Managed Switch and carefully unpack it.
2. Requirements zz A flat-blade screwdriver zz Workstations running Windows XP/2003/Vista/7/8/2008/10, MAC OS X or later, Linux, UNIX, or other platforms are compatible with TCP/IP protocols. zz Workstations are installed with Ethernet NIC (Network Interface Card) zz Ethernet Port Connection Network cables -- Use network (UTP) cables with RJ45 connectors. The above Workstations is installed with Web browser.
3. Hardware Installation 3.1 Wall Mount Installation To install the Wall-mount Managed Switch on the wall, simply follow the following steps: Step 1: Drill 4 holes with 8mm diameter on the wall. The horizontal and vertical distances between the 2 holes are 230mm and 124mm, respectively. Ø4mm 6mm Ø8mm 124mm 230mm Step 2: Hammer the four anchors into the four holes. 1 2 Step 3: Then the four given screws are screwed into the anchors to finish the wall-mount installation, as shown below.
3.2 Wall Hanging Installation To hang the Wall-mount Managed Switch on the wall, simply follow the following steps: Step 1: Drill 2 holes (one hole on each side) with 8mm diameter on the wall; the distance between the 2 holes is 230 mm and the line through them must be horizontal. Step 2: Place two anchors inside the hole by hammering them. Then screw the two screws leaving a space of 2mm apart as shown in the circled diagram below.
4. Wiring the Power Inputs The Wall-mount Managed Switch features a strong dual power input system incorporated into customer’s automation network to enhance system reliability and uptime. Model Power Input Range WGS-5225-8UP2SV PWR1 PWR2 DC 48-54V, 8A max DC 48-54V, 8A max Note: Maximum power requirements also rely on the real site application. 4-pin Spring Terminal Block Dual power input is required for maximum PoE loading. V1 V1+ V2 V1 V1+ V2+ Max.
4.1 Terminal Block Connector Pinout The Front Panel of the Wall-mount Managed Switch consists of one spring terminal block connector within 4 contacts. Please follow the steps below to insert the power wire. V1 V1+ V2 V2+ PWR 1 PWR 2 Insert positive/negative DC power wires into Contacts V1+ and V1- for Power 1, or Contacts V2+ and V2- for Power 2. 4.2 Wiring Completed in Three Steps Step 1: Press the flat-blade screwdriver diagonally into the release hole.
V1 Dual power for maximuinput is required m PoE loading. V1 V1+ V1+ PWR 1 V2 V2+ PWR 2 DC Input Range 48-54V , 8A max. Max. Fault V2 Alarm Loading : 24V, 1A Alarm Smart LCD PWR 1 V2+ PWR 2 1000 LNK/ACT 10/100 LNK/ACT bt PoE-in-U at PoE-in-Use se 1 2 Ring Fiber Mana ged WGS-5225-8U 3 1G/2.5G P2SV 4 100 5 6 R.O. LNK LNK ACT ACT 9 10 7 Wire SFP 8 PoE++ 3 SFP 9 10 Flat-blade screwdriver The wire gauge should be in the range from 12 to 16 AWG. Note 4.
5. Web Login 5.1 Starting Web Management The following shows how to start up the Web Management of the Wall-mount Managed Switch. Note the Wall-mount Managed Switch is configured through an Ethernet connection. Please make sure the manager PC must be set to the same IP subnet address. For example, the default IP address of the Wall-mount Managed Switch is 192.168.0.100, then the manager PC should be set to 192.168.0.x (where x is a number between 1 and 254, except 100) and the default subnet mask is 255.
3. After entering the password, the main screen appears as Figure 5-3 shows. Figure 5-3: Web Main Screen of Wall-mount Managed Switch The Switch Menu on the top of the Web page lets you access all the commands and statistics the Wall-mount Managed Switch provides. The Switch Menu always contains one or more buttons, such as “System”, “Switching”, “Routing”, “QoS”, “Security”, “Ring” and “Maintenance”.
5.2 Saving Configuration via the Web To save all applied changes and set the current configuration as a startup configuration, the startup-configuration file will be loaded automatically across a system reboot. 1. Click the Save icon on the top Switch Menu bar. 2. Press the “Save Configuration” button. 3. Or the other way to save the setting is to Click Maintenance, Save Startup Config.
6. SSH Login The Wall-mount Managed Switch also supports SSHv2 for remote management. The switch asks for user name and password for remote login when using SSHv2 client software; please use “admin” for both username and password. Default IP address: 192.168.0.100 Username: admin Password: admin Figure 6-1: Wall-mount Managed Switch SSHv2 Login Screen The user can now enter commands to manage the Wall-mount Managed Switch. For a detailed description of the commands, please refer to the following chapters.
6.1 Configuring IP Address The Wall-mount Managed Switch is shipped with default IP address shown below: IP Address: 192.168.0.100 Subnet Mask: 255.255.255.0 To check the current IP address or modify a new IP address for the Switch, please use the procedure as follows: Display of the Current IP Address 1. At the “#” prompt, enter “show ip interface brief”. 2. The screen displays the current IP address shown in Figure 6-2. Figure 6-2: IP Information Screen Configuration of the IP Address 3.
6.2 Storing the Current Switch Configuration At the “#” prompt, enter the following command and press . # copy running-config startup-config Figure 6-3: Saving Current Configuration Command Screen If the IP is successfully configured, the Wall-mount Managed Switch will apply the new IP address setting immediately. You can access the Web interface of the Wallmount Managed Switch through the new IP address.
7. Recovering Back to Default Configuration IP Address has been changed or admin password has been forgotten – To reset the IP address to the default IP address “192.168.0.100” or reset the login password to default value, press the reset button on the front panel for about 5 seconds. After the device is rebooted, you can log in the Web interface management within the same subnet of 192.168.0.xx. Reset Button 100 / 1G / 2.
8. LCD Touch Screen The WGS-5225-8UP2SV has a 2.4-inch color LCD touch screen with management functions. Tap the LCD touch screen to wake the LCD touch screen. Figure 8-1: To wake the LCD touch screen The factory default LCD configurations are shown as follows.
You can use the Web management interface and click LCD, and then in the LCD Management, change LCD configuration. Please refer to the user’s manual for more.
9. Customer Support Thank you for purchasing PLANET products. You can browse our online FAQ resource and User’s Manual on PLANET Web site first to check if it could solve your issue. If you need more support information, please contact PLANET support team. PLANET online FAQs: https://www.planet.com.tw/en/support/faq Support team mail address: support@planet.com.tw WGS-5225-8UP2SV User’s Manual: https://www.planet.com.
