User's Manual

- 1 -
- 2 -
- 3 -
- 4 -
- 5 -
- 6 -
- 7 -
- 8 -
1. Package Contents
Thank you for purchasing PLANET 8-port 10/100/1000T Wall-
mounted Gigabit Ethernet Switch.
In the following sections, unless specied, the term “Wall-mount
Gigabit Switch” mentioned in this user’s manual refers to the
above model.
Open the box of the Wall-mount Gigabit Switch and carefully
unpack it. The box should contain the following items:
The Wall-mount Gigabit Switch x 1 User’s Manual x 1
Wall-mounted Kit x 1 Magnet Kit x 1 RJ45 Dust Cap x 8
2. Hardware Description
2.1 Switch Front View
The front panel of the Wall-mount Gigabit Switch consists of 8
auto-sensing 10/100/1000Mbps Ethernet RJ45 ports. The LED
indicators are also located on the RJ45 ports of the Wall-mount
Gigabit Switch.
 WGS-810 Front View
3 421
7 865
PWR
ACTLNK
WGS-810
Magnet Mounting
DC Input Range
12V
, 1A max.
Industrial 8-Port
Gigabit Ethernet Switch
Standard
VLAN
Extend
Uplink
ACTLNK
Figure 2-1: WGS-810
3. Installation
3.1 Wall-mount Installation
To install the Wall-mount Gigabit Switch on the wall, simply follow
the following steps:
Step 1: Place the Wall-mount Gigabit Switch on the wall and
mark the four holes with a pencil.
133mm
Ø4mm
Ø8mm
6mm
Step 2-1: Hammer the anchors provided into the four holes and
use the four screws to tightly x the switch onto the
wall by screwing them.
PoE+
3 421
7 865
Uplink
60W
PoE Usage
45W
30W
15W
PWR
ACTLNK
PoE-in-Use
ACTLNK
WGS-814HP
PoE+
Magnet Mounting
DC Input Range
48-56V
, 1.5A max.
Industrial 8-Port Gigabit
Ethernet Switch with 4-Port PoE+
Standard
VLAN
Extend
2.3 DIP Switch
The front panel of Wall-mount Gigabit Switch provides one DIP
switch for Standard, VLAN and Extend mode selections. The
detailed descriptions are shown in the following table.
DIP Switch Mode Function
Standard
VLAN
Extend
This mode makes the Wall-mount Gigabit
Switch operate as a general switch and all
ports operate at 10/100/1000Mbps auto-
negotiation.
Standard
VLAN
Extend
This mode makes the Wall-mount Gigabit
Switch operate as a VLAN isolation switch
and
1. Port 1 to port 6 will isolate respectively.
2. Port 1 to port 6 can only communicate
with port 7 and port 8 (uplink port).
Standard
VLAN
Extend
This mode makes the Wall-mount Gigabit
Switch operate as a VLAN isolation switch and
1. Port 1 to port 6 will isolate respectively.
2. Port 1 to port 6 can only communicate
with port 7 and port 8 (uplink port).
3. Transmission distance of 250m at speed of
10Mbps.
Note
Please reboot the Wall-mount Gigabit Switch after
adjusting the DIP switch.
Power Adapter x 1 DIN-rail Kit x 1
If any item is found missing or damaged, please contact your local
reseller for replacement..
2.2 LED Indicators
 System and Ports
LED Color Function
PWR Green Lights to indicate that the Switch has power.
LNK/
ACT
Green
Lights
To indicate the link through that port is
successfully established.
Blinks
To indicate that the switch is actively
sending or receiving data over that
port.
2.4 Physical Dimensions
W x D x H: 148 x 24.2 x 134 mm
148.00
24.20
134.00
133.00
118.00
118.00
6.00
24.20
118.00
3 421
7 865
PWR
ACTLNK
WGS-810
Magnet Mounting
DC Input Range
12V
, 1A max.
Industrial 8-Port
Gigabit Ethernet Switch
Standard
VLAN
Extend
Uplink
ACTLNK
Step 2-2: Or the switch, shown in the picture below, can be hung
on the wall by screwing the two screws leaving a space
of 2mm apart after the anchors are hammered in.
2mm
M4 Screw
PoE+
3 421
7 865
Uplink
60W
PoE Usage
45W
30W
15W
PWR
ACTLNK
PoE-in-Use
ACTLNK
WGS-814HP
PoE+
Magnet Mounting
DC Input Range
48-56V
, 1.5A max.
Industrial 8-Port Gigabit
Ethernet Switch with 4-Port PoE+
Standard
VLAN
Extend
3.2 DIN-rail Mounting Installation
The DIN-rail kit is included in the Wall-mount Gigabit Switch
package. To hang up the Wall-mount Gigabit Switch, follow the
steps below:
Step 1: Screw the DIN-rail bracket on the Wall-mount Gigabit
Switch.