802.
Copyright Copyright© 2005 by PLANET Technology Corp. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of PLANET.
Federal Communication Commission (FCC) Radiation Exposure Statement This equipment complies with FCC radiation exposure set forth for an uncontrolled environment. In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antenna shall not be less than 20 cm(8 inches) during normal operation.
TABLE OF CONTENTS CHAPTER 1 INTRODUCTION.............................................................1 1.1 PACKAGE CONTENTS ......................................................................................................................1 1. 2 FEATURES ......................................................................................................................................1 1.3 SPECIFICATION ....................................................................................................
.4.1 Basic Settings..................................................................................................................34 5.4.2 Advance Settings.............................................................................................................34 5.4.3 Security ...........................................................................................................................35 5.4.4 Access Control ........................................................................
APPENDIX A NETWORK ADAPTER INFORMATION .......77 APPENDIX B FREQUENTLY ASK QUESTION.....................78 APPENDIX C GLOSSARY .........................................................
Chapter 1 Introduction Thank you for purchasing WMRT-414. This manual guides you on how to install and properly use the WMRT-414 in order to take full advantage of its features. 1.1 Package Contents Make sure that you have the following items: • • • • • One WMRT-414 One AC Power Adapter One User’s Manual CD One Quick Installation Guide Three External Dipole Antenna Note: If any of the above items are missing, contact your supplier for support. 1. 2 Features z Compliant with 802.11g / 802.
1.3 Specification Standard IEEE 802.11g/802.11b with MIMO technology Signal Type DSSS (Direct Sequence Spread Spectrum) Modulation OFDM/ QPSK / BPSK / CCK WAN Port 1 x 10/100Base-TX, Auto-MDI/MDI-X LAN Port 4 x 10/100Base-TX, Auto-MDI/MDI-X Antenna connector 3 x RP-SMA connectors Data Encryption 64 bit / 128 bit WEP, WPA-PSK, WPA, WPA2 Frequency 2.4GHz - 2.
Chapter 2 Hardware Installation Before you proceed with the installation, it is necessary that you have enough information about the WMRT-414. 2.1 Hardware Connection 1. Locate an optimum location for the WMRT-414. The best place for your WMRT-414 is usually at the center of your wireless network, with line of sight to all of your mobile stations. 2. Adjust the antennas of WMRT-414. Try to adjust them to a position that can best cover your wireless network.
2.
Chapter 3 Web Login A WMRT-414 with an assigned IP address allows you to monitor and configure via web browser (e.g., MS Internet Explorer or Netscape). 1. Open your web browser. 2. Enter the IP address of your WMRT-414 in the address field (default IP address is http://192.168.0.1). 3. A User Name and Password dialog box will appear. Please enter your User Name and Password here. Default User Name and Password are both “admin”. Click OK. 4. Then you will see the WMRT-414 HOME screen as below.
Section Description Quick Setup Select your Internet connection type and then input the configurations needed to connect to your Internet Service Provider (ISP). General Setup This section contains configurations for the Broadband router’s advance functions such as: Port Forwarding, Virtual Server, Access Control, Hacker Attack Prevention, DMZ, Special applications and other functions to meet your LAN requirements. You can also configure the wireless detail settings here.
Chapter 4 Quick Setup This section describes the basic configuration of the WMRT-414 and allows you to connect to Internet easily. 4.1 Time Zone The time information is used for Log entries and Firewall settings. You can keep the default Time Server address or set a new IP address for your router to synchronize its time. Click “Next” to continue. Parameter Description Set Time Zone Select the time zone of the country you are currently in. The router will set its time based on your selection.
4.2 Broadband Type Before establishing the Internet connection, please be sure to check with your ISP, and obtain all necessary information from them. Broadband Description Cable Modem ISP will automatically give you an IP address. Please refer to section 4.2.1 for details. Fixed-IP xDSL ISP has given you a fixed IP address already. Please refer to section 4.2.2 for details. PPPoE xDSL ISP requires you to use a Point-to-Point Protocol over Ethernet (PPPoE) connection. Please refer to section 4.2.
4.2.1 Cable Modem With Cable Modem connection, the ISP will automatically give you an IP address. Some ISP may also require you to fill in additional information such as Host Name and MAC address (see screen below). Note: The Host Name and MAC address section is optional and you can skip this section if your ISP does not require these settings for you to connect to the Internet. Parameters Description Host Name Type in the host name provided by your ISP if any; otherwise, just leave it blank.
4.2.2 Fixed-IP xDSL Select Fixed-IP xDSL if your ISP has given you a specified IP address. Your ISP should provide all the information required in this section. Parameters Description IP address assigned by your The IP address that your ISP should provide you. Service Provider Subnet Mask Enter the Subnet Mask provided by your ISP (e.g. 255.255.255.0). DNS Address The IP address of ISP’s DNS (Domain Name Service) Server. Service Provider Gateway The ISP’s IP address gateway.
4.2.3 PPPoE xDSL Select PPPoE if your ISP requires the PPPoE protocol for Internet connectivity. Your ISP should provide all the information like user name, password required in this section. Parameters Description User Name Enter the User Name provided by your ISP for the PPPoE connection. Password Enter the Password provided by your ISP for the PPPoE connection. Service Name This is an optional parameter. Leave it blank unless your ISP requires it. MTU This is an optional parameter.
packets have been sent (no one using the Internet) during this specified period, the router will automatically disconnect the connection from your ISP. Note: This “idle timeout” function may not work due to abnormal activities of some network application software, computer virus or hacker attacks from the Internet. For example, some software sends network packets to the Internet in the background, even when you are not using the Internet. So please turn off your computer when you are not using it.
Parameter Description Obtain an IP address Select it if the ISP requires you to obtain an IP address by DHCP automatically. Host Name Type in the host name provided by your ISP if any; otherwise, just leave it blank. MAC Address To connect to the Internet, your ISP will require a MAC address from your PC. Type in this MAC address in this section or use the “Clone MAC Address” button to replace the WAN port MAC address with the MAC address of that PC. To find out the PC’s MAC address, see Appendix A.
some network application software, computer virus or hacker attacks from the Internet. For example, some software sends network packets to the Internet in the background, even when you are not using the Internet. So please turn off your computer when you are not using it. This function also may not work with some ISP. So please make sure this function can work properly, especially when your ISP charges you by time used.
button to replace the WAN port MAC address with the MAC address of that PC. To find out the PC’s MAC address, see Appendix A. (also see Glossary for an explanation on MAC address. Use the following IP Select it if the ISP provides you a static IP to connect to the L2TP server. address IP Address This is the IP address that your ISP has given you to establish a L2TP connection. Subnet Mask Enter the Subnet Mask provided by your ISP (e.g. 255.255.255.
When the configuration finished please click “OK” to next step or click “Back” to previous step. After press “OK”, you will see a web screen to prompt you the configurations save successfully. Please refer to section 4.2.7 for the information of this screen. 4.2.6 Telstra Big Pond Select Telstra Big Pond if you are live in Australia and your ISP requires this protocol to connect to the Internet. Your ISP should provide all the information required in this section.
Please wait for 30 seconds for WMRT-414 restart. After restart procedure finished, please click “OK” to return to HOME screen.
Chapter 5 General Setup After click on the “General Setup” button at the main Page, you should see the screen below. The General Setup contains advanced features that allow you to configure the router to meet the network’s needs such as: Wireless, Port Forwarding, Virtual Server, Access Control, URL Blocking, Special Applications, DMZ and other functions.
5.1 System This section shows how to setup the Broadband router’s system Time Zone, Password and Remote Management Administrator.
5.1.1 Time Zone The Time Zone allows WMRT-414 to allocate its time with the settings configured; it will affect log display functions such as Security Log and Firewall settings. Parameter Description Set Time Zone Select the time zone of the country you are currently in. The router will set its time based on your selection. Time Server Address You can keep the default IP address or enter a new Time Server Address for this device to synchronize its time. You can also refer to the web site http://www.
5.1.2 Password Setup This screen allows you to change the management password. Parameters Description Current Password Enter your current password for the remote management administrator to login to your Broadband router. New Password Enter your new password. Confirmed Password Enter your new password again for verification purposes. After the setup completed, please click “Apply” to save the settings.
5.1.3 Remote Management You can specify a Host IP address that can perform remote management from Internet. Parameters Description Host Address The IP address of the host on Internet that will have management / configuration access to the Broadband router. Leave it to 0.0.0.0 means anyone can access the router’s web-based configuration from any remote location. Click the Enabled box to enable the Remote Management function.
5.2 WAN The WAN Settings screen allows you to specify the type of Internet connection. The WAN settings offer the following selections for the router’s WAN port, Dynamic IP, Static IP, PPPoE, PPTP, L2TP, and Telstra Big Pond. Please select one of the connection types and click “More Configuration” button or select the option on the left window for configuration.
5.2.1 Dynamic IP If Dynamic IP is selected, your ISP will automatically give you an IP address. Some ISP’s may also require that you fill in additional information such as Host Name, Domain Name and MAC address. Please refer to the section 4.2.1 for more settings of this option.
5.2.2 Static IP If Static IP is selected, your ISP should provide all the information required in this screen. Please refer to the section 4.2.2 for more settings of this option.
5.2.3 PPPoE Select PPPoE if your ISP requires PPPoE protocol to connect to the Internet. Your ISP should provide all the information required in this section. Please refer to the section 4.2.3 to know the detail settings of this option.
5.2.4 PPTP Select PPTP if your ISP requires the PPTP protocol to connect to the Internet. Your ISP should provide all the information required in this section. Please refer to section 4.2.4 for more settings of this option.
5.2.5 L2TP Select L2TP if your ISP requires the L2TP protocol to connect to the Internet. Your ISP should provide all the information required in this section. Please refer to section 4.2.5 for more settings of this option.
5.2.6 Telstra Big Pond Select Telstra Big Pond if your ISP is using this special protocol. Telstra Big Pond protocol is used by the ISP in Australia. Your ISP should provide all the information required in this section. Please refer to section 4.2.6 for more settings of this option.
5.2.7 DNS A Domain Name System (DNS) server is like an index of IP addresses and Web addresses. If you type a Web address into your browser, such as www.router.com, a DNS server will find that name in its index and the matching IP address. Most ISPs provide a DNS server for efficiency and convenience. If your Service Provider connects you to the Internet with dynamic IP settings, it is likely that the DNS server IP address is provided automatically.
5.2.8 DDNS DDNS allows you to map the static domain name to a dynamic IP address. You must get an account, password and your static domain name from the DDNS service providers. This router supports DynDNS and TZO. Parameters Description Dynamic DNS Enable/Disable the DDNS function of this router. Provider Select a DDNS service provider. The default setting is “DynDNS”. Domain name Your static domain name that use DDNS. Account / E-mail The account that your DDNS service provider assigned to you.
5.3 LAN The LAN Port screen below allows you to specify a private IP address for your router’s LAN interface. Parameters Description LAN IP IP Address Designate the Access Point’s IP Address. This IP Address should be unique in your network. The default IP Address is 192.168.0.1. Subnet Mask Specify a Subnet Mask for your LAN segment. The Subnet Mask of the Access Point is fixed and the value is 255.255.255.0. 802.
Domain Name You can specify the Domain Name for your Access Point. After configuration complete, please click “Apply” button to save the configuration. Then you will see a screen to prompt you the settings are save successfully. You may press “Continue” for configure other settings or “Apply” to restart WMRT-414 with new configuration. 5.4 Wireless This screen allows you to Enable/Disable WMRT-414 wireless function.
5.4.1 Basic Settings WMRT-414 supports not only Access Point function, but also provides Bridge and WDS mode. Please Refer to “Chapter 6 Wireless Configuration” know the details settings of wireless Basic Settings. In Default, WMRT-414 will work with AP mode. 5.4.2 Advance Settings You should not change the parameters in this screen unless you know what effect the changes will have on WMRT-414. When configuration finished, please click “Apply” to save the settings.
Parameters Description Fragment Threshold “Fragment Threshold” specifies the maximum size of packet during the fragmentation of data to be transmitted. If you set this value too low, it will result in bad performance. RTS Threshold When the packet size is smaller the RTS threshold, the access point will not use the RTS/CTS mechanism to send this packet. Beacon Interval The interval of time that this access point broadcast a beacon. Beacon is used to synchronize the wireless network.
5.4.3.1 WEP When you select 64-bit or 128-bit WEP key, you have to enter WEP keys to encrypt data. You can generate the key by yourself. You can enter four WEP keys and select one of them as default key. Then the access point will just allow the clients that with the same encryption keys connected. You can use WEP encryption in “AP mode”, “Station-Ad Hoc mode”, “Station-Infrastructure mode” and “AP Bridge-WDS mode”. If you would like to enable 802.1x Authentication also, please check the “Enable 802.
Parameter Description Encryption Please select “WEP” in this option. Key Length You can select the 64 or 128-bit key to encrypt transmitted data. Larger WEP key length will provide higher level of security, but the throughput will be lower. Key Format You may select to select ASCII Characters (alphanumeric format) or Hexadecimal Digits (in the “A-F”, “a-f” and “0-9” range) to be the WEP Key. Default Tx Key Select one of the four keys to encrypt your data.
Parameter Description Encryption If you want to use 802.1x only, keep this setting in “Disable”. Enable 802.1x Authentication Please check this option to enable 802.1x function. RADIUS Server IP Address RADIUS Server Port Enter RADIUS Serer IP address. Leave the default port setting or assign a new port number for this option. RADIUS Server Password Please enter the password that is configured in RADIUS Server. After configuration complete, please click “Apply” button to save the configuration.
Parameter Description Encryption Please select “WPA pre-shared key” in this option. WPA (TKIP) TKIP can change the encryption key frequently to enhance the wireless LAN security. WPA Unicast WPA2 (AES) Cipher Suite This use CCMP protocol to change encryption key frequently. AES can provide high-level encryption to enhance the wireless LAN security. WPA2 Mixed This will use TKIP or AES based on the other communication peer automatically.
5.4.3.4 WPA RADIUS You can use a RADIUS server to authenticate wireless stations and provide the session key to encrypt data during communication. It uses TKIP or CCMP (AES) to change the encryption key frequently. Parameter Description Encryption Please select “WPA RADIUS” in this option. WPA (TKIP) TKIP can change the encryption key frequently to enhance the wireless LAN security. WPA Unicast WPA2 (AES) Cipher Suite This use CCMP protocol to change encryption key frequently.
5.4.4 Access Control WMRT-414 provides MAC Address Filtering, which prevents the unauthorized users from accessing your wireless network. Parameters Description Enable Wireless Enable or disable the MAC Address Filtering function. Access Control Add MAC Address In the bottom “New” area, fill in the “MAC Address” and “Comment” of the wireless to the control table station and then click “Add”. Then this wireless station will be added into the “MAC Address Filtering Table” above.
5.5 QoS Quality of Service (QoS) refers to the capability of providing better service to selected network traffic. The primary goal of QoS is to provide priority including dedicated bandwidth, controlled jitter and latency (required by some real-time and interactive traffic), and improved loss characteristics. When using this feature, it is important to make sure the rules are not conflicted with each other.
5.5.1 Add/Edit QoS Rule You can assign packet classification criteria by its source IP range, destination IP range, traffic type, protocol, source port range and destination port range parameters. The parameters that you leave as blank will be ignored. The priority of this rule will be applied to packets that match classification criteria of this rule. You can limit bandwidth consumed by packets that match this rule or guarantee bandwidth required by packets that match this rule.
port number, if you are familiar with the application protocol. Protocol Please select the protocol TCP or UDP in the list. After configuration complete, please click “Save” to save the settings. Or you may press “Reset” to clear the settings to enter again. 5.6 NAT Network Address Translation (NAT) allows multiple users at your local site to access the Internet via a single legal IP Address.
5.6.1 Port Forwarding The Port Forwarding allows you to re-direct a particular range of service port numbers (from the Internet/WAN Ports) to a particular LAN IP address. It helps you to host some servers behind the firewall. Parameters Description Enable Port Forwarding Enable Port Forwarding. Private IP This is the private IP of the server in LAN. Note: You need to give your LAN PC clients a fixed/static IP address for Port Forwarding to work properly.
Current Port Forwarding Table Delete Selected If you want to remove some MAC address from the “Current Access Control List”, select the MAC addresses you want to remove in the table and then click “Delete Selected”. Delete All If you want remove all MAC addresses from the table, just click this button. Reset Click “Reset” will clear your current selections. After configuration complete, please click “Apply” button to save the configuration.
Note: You need to give your LAN PC clients a fixed/static IP address for Virtual Server to work properly. Private Port This is the port number (of the above Private IP host) that the below Public Port number will be changed to when the packet enters your LAN (to the LAN Server/Client IP). Type Select the port number protocol type (TCP, UDP or Both). If you are unsure, then leave it to the default both protocols.
5.6.3 Special Applications Some applications require multiple connections, such as Internet games, video conferencing, Internet telephony and others. In this section you can configure the router to support multiple connections for these types of applications. Parameters Description Enable Trigger Port Enable the Special Application function. Trigger Port This is the out going (Outbound) range of port numbers for this particular application.
for this popular application into the input fields. Add Add the settings into the “Current Trigger Port Table”. Reset Click “Reset” will clear your current settings to allows you to enter again. Current Trigger Port Table Delete Selected If you want to remove some items from the “Current Trigger Port Table”, select the MAC addresses you want to remove in the table and then click “Delete Selected”. Delete All If you want to remove all items from the table, just click this button.
5.6.4 UPnP UPnP is more than just a simple extension of the Plug and Play peripheral model. It is designed to support zero-configuration, "invisible" networking, and automatic discovery for a breadth of device categories from a wide range of vendors. With UPnP, a device can dynamically join a network, obtain an IP address, convey its capabilities, and learn about the presence and capabilities of other devices-all automatically; truly enabling zero configuration networks.
5.6.5 ALG Settings You can select applications that need “Application Layer Gateway” to support. Parameters Description Enable You can select to enable “Application Layer Gateway” of an application and then the router will let that application correctly pass though the NAT gateway. After configuration complete, please click “Apply” button to save the configuration. Then you will see a screen to prompt you the settings are save successfully.
Parameters Description Enable/Disable You can select to enable or disable the firewall function. After selected, please click “Apply” to make the settings effect. After configuration complete, please click “Apply” button to save the configuration. Then you will see a screen to prompt you the settings are save successfully. You may press “Continue” for configure other settings or “Apply” to restart WMRT-414 with new configuration.
5.7.1 Access Control This screen allows you to restrict users from accessing certain Internet applications/services (e.g. Internet websites, email, FTP etc.). Network administrator can define the traffic type permitted in your LAN and control which PC client can have access to these services. Parameters Description Enable MAC Filtering Check “Enable MAC Filtering” to enable MAC Filtering. If select “Deny”, all PCs will be allowed to access Internet accept for the PCs in the list below.
in the list below. Add PC You can click “Add PC” to add an access control rule for users by IP addresses. Please refer to section 5.7.1.1. Remove PC If you want to remove some PCs from the "IP Filtering Table", select the PC you want to remove in the table and then click "Delete Selected". Delete All If you want to delete all PCs. Please click this button. 5.7.1.1 Add PC Parameters Description Client PC Description The description for this client PC.
Note: You need to give your LAN PC clients a fixed/static IP address for the Access Control rule to work properly. Client PC Service You can block the clients from accessing some Internet services by checking the services you want to block. Protocol This allows you to select UDP, TCP or Both protocol types. Port Range You can assign up to five port ranges. The router will block clients from accessing Internet services that use these ports. Add Click “Add” to save the settings.
be cleared. Remove URL / Keyword If you want to remove some URL keyword from the "Current URL Blocking Table", select the URL keyword you want to remove in the table and then click "Delete Selected". If you want remove all URL keyword from the table, just click "Delete All" button. If you want to clear the selection and re-select again, just click “Reset”. After configuration complete, please click “Apply” button to save the configuration.
After configuration complete, please click “Apply” button to save the configuration. Then you will see a screen to prompt you the settings are save successfully. You may press “Continue” for configure other settings or “Apply” to restart WMRT-414 with new configuration. 5.7.4 DMZ If you have a local client PC that cannot run an Internet application (e.g. Games) properly from behind the NAT firewall, you can open the client up to unrestricted two-way Internet access by defining a DMZ Host.
After configuration complete, please click “Apply” button to save the configuration. Then you will see a screen to prompt you the settings are save successfully. You may press “Continue” for configure other settings or “Apply” to restart WMRT-414 with new configuration.
Chapter 6 Wireless Configuration In this chapter, you can Enable/Disable wireless function and configure the WMRT-414 work in different operating mode. Please refer to below sections to know the details configuration of each operating mode. 6.1 AP Mode This mode is set to WMRT-414 by default. It served as a transparent Media Access Control (MAC) bridge between wired and wireless network.
Parameter Description Mode Shows the current operation mode. You may set WMRT-414 to other operating mode by select other operating mode. Band 2.4GHz (B): It forces the WMRT-414 to operate in 802.11b only. 2.4GHz (G): It forces the WMRT-414 to operate in 802.11g only. 2.4GHz (B+G): It allows the WMRT-414 to operate in 802.11b and 802.11g simultaneously. ESSID The ESSID (up to 32 printable ASCII characters) is the unique name identified in a WLAN.
6.2 AP Bridge - Point to Point Mode This function allows WMRT-414 to bridge 2 wired Ethernet networks wirelessly. Parameter Description Mode Shows the current operation mode. You may set WMRT-414 to other operating mode by select other operating mode. Band 2.4GHz (B): It allows to select the transmit rate up to 11Mbps. 2.4GHz (G): It allows to select the transmit rate up to 54Mbps. 2.4GHz (B+G): It allows selecting the 802.11b and 802.11g data rates.
6.3 AP Bridge - Point to Multipoint Mode This function allows WMRT-414 to bridge more than 2 wired Ethernet networks together by wireless connection. Parameter Description Mode Shows the current operation mode. You may set WMRT-414 to other operating mode by select other operating mode. Band 2.4GHz (B): It allows to select the transmit rate up to 11Mbps. 2.4GHz (G): It allows to select the transmit rate up to 54Mbps. 2.4GHz (B+G): It allows selecting the 802.11b and 802.11g data rates.
other settings or “Apply” to restart WMRT-414 with new configuration. 6.4 AP Bridge - WDS Mode If you want WMRT-414 to bridge to other WMRT-414 and provide access for other wireless clients at the same time, you have to set the WMRT-414 to “AP Bridge - WDS”. Simply speaking, “AP Bridge - WDS” function is the combination of “AP mode” and “AP Bridge-Point to Multi-Point mode”. Parameter Description Mode Shows the current operation mode.
Channel 1-11 (North America) Channel 1-14 (Japan) Channel 1-13 (Europe) MAC Address 1-4 If you want to bridge more than two wired Ethernet networks together with wireless connection, you have to enter the MAC addresses of otherWMRT-414s that with join the bridging work into the fields. Set Security IF you want to enable security to protect your wireless connection. Please press “Set Security” button and refer to section “6.5 Security setting for bridge mode” to configure the detail settings.
6.5.1 WEP When you select 64-bit or 128-bit WEP key, you have to enter WEP keys to encrypt data. You can generate the key by yourself. You can enter four WEP keys and select one of them as default key. Then the access point will just allow the clients that with the same encryption keys connected. Parameter Description Key Length You can select the 64 or 128-bit key to encrypt transmitted data. Larger WEP key length will provide higher level of security, but the throughput will be lower.
6.5.2 WPA-PSK Wi-Fi Protected Access (WPA) is an advanced security standard. You can use a pre-shared key to authenticate wireless stations and encrypt data during communication. It uses TKIP or CCMP (AES) to change the encryption key frequently. So the encryption key is not easy to be broken by hackers. This can improve security very much. Parameter Description Encryption Please select “WPA pre-shared key” in this option.
Chapter 7 Status The Status screen allows you to monitor the current status of your router. You can use the Status page to monitor the connection status of WAN and LAN interfaces, the current firmware and hardware version numbers, any illegal attempts to access your network, and information on all DHCP client PCs currently connected to your network.
7.1 Internet Connection View WMRT-414’s current Internet connection status and other related information. 7.2 Device Status View WMRT-414’s current configuration settings. The Device Status displays the configuration settings of WLAN and LAN.
7.3 System Log This screen will show you the real-time information of WMRT-414. Parameters Description System Log This page shows the current system log of WMRT-414. It displays the working information about WMRT-414. About the bottoms of the page, the system log can be saved to a local file by press “Save” button.
press “Clear” button to clear the system log . It can be refreshed to get the most updated situation by press “Refresh” button. When the system is powered down, the system log will be cleared. 7.4 Security Log View any attempts that have been made to illegally gain access to your network. Parameters Description Security Log This page shows the current security log of WMRT-414. It displays any illegal attempts to access your network.
7.5 Active DHCP Client View your client's information that is currently linked to WMRT-414's DHCP server. Parameters Description DHCP Client Table This page shows all the DHCP clients currently connected to your network. The “Active DHCP Client Table” displays the IP address and the MAC address and Time Expired of each Client. Use the Refresh button to get the most updated situation.
7.6 Statistics View the statistics of packets sent and received on WLAN, LAN and WAN. Parameters Description Statistics Shows the counters of packets sent and received on WLAN, LAN and WAN.
Chapter 8 Tools This page includes the basic configuration tools, such as Configuration Tools (save or restore configuration settings), Firmware Upgrade (upgrade system firmware) and Reset. 8.1 Configuration Tools The Configuration Tools screen allows you to “Backup” the router’s current configuration setting. Saving the configuration settings provides an added protection and convenience when problems occur and you have to reset to factory default.
Parameters Description Configuration Tools Use the "Backup" tool to save WMRT-414 current configuration to a file named "config.bin" in your PC. You can then use the "Restore" tool to restore the saved configuration to WMRT-414. The "Restore to Factory Defaults" tool can force WMRT-414 to perform a power reset for restore it to original factory settings. After configuration complete, please click “Apply” button to save the configuration.
Parameters Description Firmware Upgrade This tool allows you to upgrade WMRT-414’s system firmware. To upgrade the firmware of your Broadband router, you need to download the firmware file to your local hard disk, and enter that file name and path in the appropriate field on this page. You can also press the “Browse…” button to find out the firmware file on your PC. Once you’ve selected the new firmware file, click “Apply” bottom to start the upgrade process.
Parameters Description Reset In the event that the system stops responding correctly or in some way stops functioning, you can perform a reset. Your settings will not be changed. To perform the reset, click on the “Apply” button. You will be asked to confirm your decision. The reset will be complete when the power light stops blinking. Once the reset process is complete you may start using the router again.
Appendix A Network Adapter Information 1. In Window’s open the Command Prompt program. 2. Type “ipconfig /all” and press “Enter” key. Then you can see the information of your network adapter. Your PC’s IP address is the one entitled IP address (192.168.0.100). The router’s IP address is the one entitled Default Gateway (192.168.0.1). Your PC’s MAC Address is the one entitled Physical Address (00-0C-6E-A5-BF-98).
Appendix B Frequently Ask Question Q. What is MIMO? A: MIMO (multiple-input multiple-output), a technique for boosting wireless bandwidth and range by taking advantage of multiplexing. MIMO algorithms in a radio chipset send information out over two or more antennas. The radio signals reflect off objects, creating multiple paths that in conventional radios cause interference and fading.
Q. When WMRT-414 works with WDS mode, can wireless connect to it? A. Yes, WDS mode is work as a AP and Bridge at the same time. So the wireless client can access to WDS mode WMRT-414 without problem. When wireless client connect to the remote site via WDS mode, the performance will be 50% then access to the connected WDS mode WMRT-414. Just like connect to AP via a repeater.
Appendix C Glossary Access Point Access points are way stations in a wireless LAN that are connected to an Ethernet hub or server. Users can roam within the range of access points and their wireless device connections are passed from one access point to the next. Authentication Authentication refers to the verification of a transmitted message's integrity. DMZ DMZ (DeMilitarized Zone) is a part of an network that is located between a secure LAN and an insecure WAN.
transferring large files or uploading the HTML pages for a Web site to the Web server. Gateway Gateways are computers that convert protocols enabling different networks, applications, and operating systems to exchange information. Host Name The name given to a computer or client station that acts as a source for information on the network. HTTP HTTP (HyperText Transport Protocol) is the communications protocol used to connect to servers on the World Wide Web.
Messages larger than the MTU are divided into smaller packets. NAT NAT (Network Address Translation - also known as IP masquerading) enables an organization to present itself to the Internet with one address. NAT converts the address of each LAN node into one IP address for the Internet (and vice versa). NAT also provides a certain amount of security by acting as a firewall by keeping individual IP addresses hidden from the WAN.
Server Servers are typically powerful and fast machines that store programs and data. The programs and data are shared by client machines (workstations) on the network. SMTP SMTP (Simple Mail Transfer Protocol) is the standard Internet e-mail protocol. SMTP is a TCP/IP protocol defining message format and includes a message transfer agent that stores and forwards mail. SNMP SNMP (Simple Network Management Protocol) is a widely used network monitoring and control protocol.
delivery isn't necessary (for example, real-time video and audio where packets can be dumped as there is no time for retransmitting the data). Virtual Servers Virtual servers are client servers (such as Web servers) that share resources with other virtual servers (i.e., it is not a dedicated server). WEP WEP (Wired Equivalent Privacy) is the de facto security protocol for wireless LANs, providing the "equivalent" security available in hardwired networks.
