User's Manual FST-801 FST-802 FST-802S15/802S35/802S50 FST-806A20/806B20 10/100Base-TX to 100Base-FX Smart Media Converter -1-
Trademarks Copyright © PLANET Technology Corp. 2010 Contents subject to revision without prior notice. PLANET is a registered trademark of PLANET Technology Corp. All other trademarks belong to their respective owners. Disclaimer PLANET Technology does not warrant that the hardware will work properly in all environments and applications, and makes no warranty and representation, either implied or expressed, with respect to the quality, performance, merchantability, or fitness for a particular purpose.
TABLE OF CONTENTS 1. INTRODUCTION ...................................................................................................................................................... 4 1.1 CHECKLIST................................................................................................................................................................ 4 1.2 ABOUT THE 10/100BASE-TX TO 100BASE-FX SMART MEDIA CONVERTER ............................................................. 4 1.3 FEATURES ........
1. INTRODUCTION 1.
1.4 Specification Model Hardware Specification Standards Ports Fiber connector Wavelength Deployment Cable FST-801 FST-802 FST-802S15 FST-802S35 FST-802S50 IEEE 802.3 10Base-T, IEEE 802.3u 100Base-TX and 100Base-FX 1 10/100Base-TX port , 1 100Base-FX port ST SC SC SC SC 1310nm (Transmit and Receive) FST-806A20 FST-806B20 SC, WDM 1310 (TX) 1550 (RX) SC, WDM 1550 (TX) 1310 (RX) Power input Power consumption Operate environment 10Base-T: 2-pair Cat.
1.5 Product Outlook Right View: there is one RJ-45 twisted-Pair jack (Auto-MDI/MDI-X), one fiber-optic connector (vary by model) and six LED indicators. Left View: there is one DC jack for DC 5V power adapter.
2. HARDWARE INSTALLATION This product provides two different running speeds – 10/100Base-TX and 100Base-FX in the same device and the 10/100Base-TX RJ-45 port can automatically distinguish the speed of incoming connection. This section describes the hardware installation of FST-80x. Before connecting any network device to the FST-80x, read this chapter carefully. 2.
2.2 Slide Media Converter module into MC-1600MR/R48 Chassis installation Step 1- Unscrew and pull out the FST-80x Media Converter board. Step 2- Remove a blank faceplate from an empty expansion slot on the front of the chassis. The FST-80x Media Converter board can be installed in any expansion slot. Step 3- Slide the FST-80x Media Converter board into the expansion slot, aligning it with the guide rails, until it firmly connects to the chassis’ backplane.
2.3 Real Ethernet environment application Standalone and centralize management Media Converter installation Afford the current network grows and expanding, the PLANET FST-80x provide advanced Media conversion technology to fill this kind of demand. The FST-80x provide the diverse fiber connect type options to meet different network application, it is very flexible for FST-80x work as a standalone devices or install into the central Web Smart Media converter chassis for centralize management.
3. MANAGE THE MEDIA CONVERTER This product provides two different managed methods – configure through its DIP Switch or install into the central Web Smart Media converter chassis for centralize management. This section describes how to managed the FST-80x through its DIP Switch and Web Smart Media converter chassis. Before use the FST-80x smart function, please read this chapter carefully. 3.
3.2 Managed Media Converter module through MC-1600MR/R48 Chassis The Web Smart Media Coverter Chassis that can control FST-80X through the management system,FST-80X can be controlled through Web Browser and terminal emulation program. The Web Smart Media Converter Chassis will display out the status of FST-80x, also the Web Smart Media Coverter Chassis can control the function through the management system.
4. LINK PASS THROUGH FUNCTION The LFP function includes the Link Fault Pass Through function (LLCF/LLR) and the DIP Switch design. LLCF/LLR can immediately alarm administrators the problem of the link media and provide efficient solution to monitor the net. The DIP Switch provides disable or enable the LFP function. LLCF (Link Loss Carry Forward) means when a device connected to the converter and the TP line loss the link, the converter’s fiber will disconnect the link of transmit.
4.2 Link Loss Return (LLR) The fiber ports of FST-80X have been designed with an LLR function for troubleshooting a remote connection. LLR works in conjunction with LLCF. When LLR is enabled*, the port’s transmitter shuts down when its receiver fails to detect a valid receive link. LLR should only be enabled on one end of the link and is typically enabled on either the unmanaged or remote device.
5. TROUBLESHOOTING This chapter contains information to help you solve issues. If the FST-80x is not functioning properly, make sure the FST-80x was set up according to instructions in this manual. The Power LED is not lit Solution: Check the power cable connection between power adapter and FST-80X. Why I connect FST-80x to device with 100Base-FX interface and the 100Base-FX fiber connection fail? Solution: 1. Please check the fiber connection between two devices is correct. 2.
APPENDIX A NETWORKING CONNECTION A.1 Switch‘s RJ-45 Pin Assignments 10/100Mbps, 10/100Base-TX RJ-45 Connector pin assignment Contact MDI MDI-X Media Dependant Interface Media Dependant Interface -Cross 1 Tx + (transmit) Rx + (receive) 2 Tx - (transmit) Rx - (receive) 3 Rx + (receive) Tx + (transmit) 4, 5 6 7, 8 Not used Rx - (receive) Tx - (transmit) Not used A.
A.3 Cable Connection Parameter The limitations are shown as below; Duplex Connection Limitation (max.) Twisted Pair Half / Full Node to Node 100 meters Node to Switch/ Hub Multi-Mode Converters MM Half Node to Node 412 meters Node to Switch MM Full Node to Node 2 kilometers Node to Switch Single-Mode Converters (FST-80xynn; x=2,6; y=S,A,B ; nn=km) SM Full Node to Node Depends on model Node to Switch #Notice: 1: Consult your local dealer for more about PLANET single mode fiber connectivity.
EC Declaration of Conformity For the following equipment: *Type of Product *Model Number * Produced by: Manufacturer‘s Name Manufacturer‘s Address : 10/100Base-TX to 100Base-FX (WDM) Bi-directional Smart Media Converter : FST-806A20/B20 : : Planet Technology Corp. 11F, No. 96, Min Chuan Road, Hsin Tien Taipei, Taiwan , R. O.C.
EC Declaration of Conformity For the following equipment: *Type of Product *Model Number * Produced by: Manufacturer‘s Name Manufacturer‘s Address : 10/100Base-TX to 100Base-FX Smart Media Converter (SC,SM) : FST-802S15_S35_S50 : : Planet Technology Corp. 11F, No. 96, Min Chuan Road, Hsin Tien Taipei, Taiwan , R. O.C.
EC Declaration of Conformity For the following equipment: *Type of Product *Model Number * Produced by: Manufacturer‘s Name Manufacturer‘s Address : 10/100Base-TX to 100Base-FX Smart Media Converter : FST-801_802 : : Planet Technology Corp. 11F, No. 96, Min Chuan Road, Hsin Tien Taipei, Taiwan , R. O.C.