User's Manual FSD-804P 8-Port 10/100Mbps with 4-Port PoE Fast Ethernet Switch -1-
Trademarks Copyright © PLANET Technology Corp. 2008. Contents subject to revision without prior notice. PLANET is a registered trademark of PLANET Technology Corp. All other trademarks belong to their respective owners. Disclaimer PLANET Technology does not warrant that the hardware will work properly in all environments and applications, and makes no warranty and representation, either implied or expressed, with respect to the quality, performance, merchantability, or fitness for a particular purpose.
TABLE OF CONTENTS 1. INTRODUCTION............................................................................................................. 4 1.1 CHECKLIST ................................................................................................................................................ 4 1.2 HOW TO USE THIS MANUAL ........................................................................................................................ 4 1.3 FEATURES ...........................................
1. INTRODUCTION 1.1 Checklist Check the contents of your package for following parts: FSD-804P x1 User's manual CD x1 Power cord x 1 If any of these pieces are missing or damaged, please contact your dealer immediately, if possible, retain the carton including the original packing material, and use them against to repack the product in case there is a need to return it to us for repair. 1.
1.4 Specification Model FSD-804P Hardware Specification Network Connector 8-Port RJ-45 for 10/100Base-TX PoE Inject Port 4-Port with PoE injector function, Port-1 to Port-4 LED Display One power, 1-4 port PoE in-use, LNK/ACT 5-8 port LNK/ACT Switch Architecture Store and Forward switch architecture Switch Fabric 1.6Gbps MAC Address 1K MAC address table with Auto learning function Throughput 1.19Mbps Remote power feeding End-point insert type and compatible with IEEE 802.
2. HARDWARE DESCRIPTION This product provides two different running speeds – 10Mbps, 100Mbps in the same switch and automatically distinguishes the speed of incoming connection. This section describes the hardware features of FSD-804P. For easier management and control of the Switch, familiarize yourself with its display indicators, and ports. Front panel illustrations in this chapter display the unit LED indicators. Before connecting any network device to the FSD-804P, please read this chapter carefully.
LNK/ACT Green Lit: indicate the link through that port is successfully established. Blinks to indicate that the Switch is actively sending or receiving data over that port. 2.3 Rear Panel The rear panel of the FSD-804P indicates an AC inlet power socket, which accepts input power from 100 to 240VAC, 50-60Hz. And have a fan hole on the rear panel. Figure 2-2 FSD-804P Switch rear panel 1. The device is a power-required device, it means, it will not work till it is powered.
2.5 Desktop Installation To install the Switch on desktop, simply follow the next steps: Step1: Attach the rubber feet to the recessed areas on the bottom of the Switch, as shown in Figure 2-3. Figure 2-3 Attaching the rubber feet to the Fast Ethernet Switch Step2: Place the Switch on desktop near an AC power source. Step3: Keep enough ventilation space between the Switch and the surrounding objects.
2.6 Rack Mounting To install the Switch in a 10-inch standard rack, follow the instructions described below. Step1: Place your Fast Ethernet Switch on a hard flat surface, with the front panel positioned towards your front side. Step2: Attach a rack-mount bracket to each side of the Switch with supplied screws attached to the package. Figure 2-4 shows how to attach brackets to one side of the Switch. Figure 2-4 Attaching the brackets to the Switch.
2.7 Product Application 2.7.1 Connecting end node or switch 1. Place the FSD-804P on a smooth surface or fasten the mounting brackets purchased separately with the provided screws in a standard 19” rack. 2. Connect the power cord to the power inlet socket of FSD-804P and the other end into the local power source outlet. When the Switch receives power, the Power LED should remain solid Green. 3. 4. Connect other switch or PC to one port of the FSD-804P using Category 3/4/5 UTP/STP cabling.
2.7.2 Department/ Workgroup PoE Switch: Providing up to 4 PoE, in-line power interfaces, the Switch can easily build a power central-controlled IP phone system, IP camera system, AP group for the enterprise. For instance, 4 camera / AP can be easily installed around the corner in the company for surveillance demands or build a wireless roaming environment in the offices. Without the power-socket limitation, the switch makes the installation of cameras or WLAN AP more easily and efficiently.
2.8 Power over Ethernet Powered Device Voice over IP phones Enterprise can install POE VoIP Phone, ATA and other Ethernet/non-Ethernet end-devices to the central where UPS is installed for un-interrupt power system 3~5 watts and power control system.
3. SWITCH OPERATION 3.1 Address Table The Switch is implemented with an address table. This address table composed of many entries. Each entry is used to store the address information of some node in network, including MAC address, port no, etc. This information comes from the learning process of Ethernet Switch. 3.2 Learning When one packet comes in from any port. The Switch will record the source address, port no. And the other related information in address table.
4. POWER OVER ETHERNET OVERVIEW What is PoE? Based on the global standard IEEE 802.3af, PoE is a technology for wired Ethernet, the most widely installed local area network technology adopted today. PoE allows the electrical power necessary for the operation of each end-device to be carried by data cables rather than by separate power cords. New network applications, such as IP Cameras, VoIP Phones, and Wireless Networking, can help enterprises improve productivity.
The data pairs are used. Since Ethernet pairs are transformer coupled at each end, it is possible to apply DC power to the center tap of the isolation transformer without upsetting the data transfer. In this mode of operation the pair on pins 3 and 6 and the pair on pins 1 and 2 can be of either polarity.
5. THE POE PROVISION PROCESS While adding PoE support to networked devices is relatively painless, it should be realized that power cannot simply be transferred over existing CAT-5 cables. Without proper preparation, doing so may result in damage to devices that are not designed to support provision of power over their network interfaces. The PSE is the manager of the PoE process.
5.3 Start-up Once line detection and optional classification stages are completed, the PSE must switch from low voltage to its full voltage capacity (44-57 Volts) over a minimal amount of time (above 15 microseconds). A gradual startup is required, as a sudden rise in voltage (reaching high frequencies) would introduce noise on the data lines. Once provision of power is initiated, it is common for inrush current to be experienced at the PSE port, due to the PD’s input capacitance.
6.TROUBLESHOOTING This chapter contains information to help you solve problems. If the Switch is not functioning properly, make sure the Ethernet Switch was set up according to instructions in this manual. The Link LED is not lit Solution: Check the cable connection and remove duplex mode of the Switch. Performance is bad Solution: Check the full duplex status of the Switch. If the Ethernet Switch is set to full duplex and the partner is set to half duplex, then the performance will be poor.
APPENDIX A NETWORKING CONNECTION A.1 DATA OUT PoE Switch RJ-45 Port Pin Assignments (Port 1 to Port-4) PIN NO 1 RJ-45 SIGNAL ASSIGNMENT • Output Transmit Data + • Power + 2 • Output Transmit Data – • Power + 3 • Receive Data + • Power - 4 - 5 - 6 • Receive Data – • Power - 7 - 8 - A.2 Switch‘s RJ-45 Pin Assignments (Port-5 to Port-8) Contact MDI MDI-X 1 1 (TX +) 3 2 2 (TX -) 6 3 3 (RX +) 1 6 6 (RX -) 2 4, 5, 7, 8 Not used Not used A.
There are 8 wires on a standard UTP/STP cable and each wire is color-coded.
APPENDIX B B.1 Power over Ethernet Compatibility test No. PDs PoE Output Note 1 [PLANET POE-151S-12V] + [PLANET ICA-500] 9.6W 2 [PLANET POE-151S-12V] + PLANET ICA310 6.4W 3 [PLANET POE-152S-12V] + [PLANET ICA-500] 7.3W 4 [PLANET POE-151S-12] + CAM-IR338-NT 5.1W LED Off 5 [PLANET POE-151S-12] + CAM-IR338-NT 13.5W~14.3W LED On 6 PLANET VIP-155PT 3W 7 PLANET VIP-154PT 4.9W~5.6W 8 PLANET VIP-550PT 4~4.5W 9 PLANET WAP-4060PE 4.3W Standby 10 PLANET FSD-803PE 2.
