User Manual

- 2 - - 4 - - 6 - - 8 -
- 1 - - 3 - - 5 - - 7 -
1. Package Contents
Thank you for purchasing PLANET Industrial IP67 1000BASE-X SFP to
10/100/1000BASE-T 802.3at PoE+ Media Converter, IGTP-825AT. In the
following sections, the term “Outdoor PoE+ Media Converter” means
the IGTP-825AT.
Open the box of the Outdoor PoE+ Media Converter and carefully
unpack it. The box should contain the following items:
IGTP-825AT x 1 User's Manual x 1
M22 Waterproof
Cable Gland x 3
Power Cable with 2-pin
Terminal Block x 1
Wall-mounted Kit x 1 Ground Wire x 1
If any of these are missing or damaged, please contact your dealer
immediately; if possible, retain the carton including the original packing
material, and use them again to repack the product in case there is a
need to return it to us for repair.
2.2 Power Input Port
Figure 2-2 shows the power input port side of the IGTP-825AT
Figure 2-2: IGTP-825AT Power Input port side
2.3 Data Input Port and 802.3at PoE+ Output Port
Figure 2-3 shows the “Data + PoE+” output port and “Data” input port
side of the IGTP-825AT.
PoE+ Output Port Data Input Port
Figure 2-3: IGTP-825AT RJ45 / SFP ports side
Caution
Make sure the clamping nut is tightly attached to the
cable gland body and the sealing insert is squeezed
tightly.
Step 5: Repeat Steps 1 to 4 for “PoE (Data + Power)” Output Port.
Fiber Cable Gland Installation
Step 6: Insert the SFP transceiver into the “Data” Iutput Port.
3. Installation
This section describes how to install the Outdoor PoE+ Media Converter
and make connections to it. Please read the following sections and
perform the procedure in the order being presented.
3.1 Installing Cable Gland with Power Cable and RJ45
UTP Cable
The cable gland consists of the following:
3.2 Connecting Waterproof Cable Kit to the Outdoor
PoE+ Media Converter
Step 1: Turn clockwise to tighten the gland body connected to the
Outdoor PoE+ Media Converter.
2. Hardware Introduction
This section describes the functionalities of the Outdoor PoE+ Media
Converter’s components.
2.1 Product Outlook
Unit: mm
LNK/
ACT
PoE
+
Data
IGTP-825AT
LNK
PWR
DC Input Range:
24-56V , 2A max.
V+
Figure 2-1: IGTP-825AT product outlook
2.4 LED Indicators
LED Color Function
PWR Green Indicates it has power.
LINK/ACT Green
Lights to indicate the port is linked up at
10/100/1000Mbps.
Blinks to indicate that the IGTP-825AT is actively
sending or receiving data over that port.
LINK Green
Indicate the port is linked up at 1000Mbps and
actively sending or receiving data over that port.
To install the 2-pin Terminal Block Connector on the Outdoor PoE+
Media Converter, simply follow the following steps:
Step 1: Insert positive DC power wire into V+, negative DC power
wire into V-, and grounding wire into Ground.
V+
V
-
2-pin
Step 2: Tighten the wire-clamp screws for preventing the wires
from loosening and plug them into the Outdoor PoE+ Media
Converter.
Note
1. The wire gauge should be in the range from 20 to 22
AWG.
2. The device must be grounded.
Step 2: Plug the power cable connector into the power input port.
Step 3: Insert the sealing insert into the cable gland body.
Step 4: Attach the clamping nut to the cable gland to complete the
cable assembly.
Step 7: Thread the cable gland over the ber cable in the order as
indicated below and attach the two-hole sealing to the ber
cable.
Step 8: ConnectthebercabletotheSFPtransceiver.
Step 9: Turn clockwise to tighten the gland body.