H.
Overview This quick installation guide describes the objectives; organization and basic installation of the PLANET VIP-281/VIP-480/VIP-880/VIP-1680/VIP-2480 H.323/SIP VoIP Gateway (“VIP-GW” in the following term), and explains how to establish your first voice over IP communication via PLANET product. Also, this guide shows you how to find additional information on related products and services.
ll VIP-1680FO equips sixteen FXO interfaces to have the great flexibility of PBX connection (FXO). ll VIP-1680FD equips sixteen FXO interfaces support Caller ID to have the great flexibility of PBX connection (FXO). 24-Port Model ll VIP-2480 equips twelve FXO and twelve FXS interfaces to have the great flexibility of PBX connection (FXO), and telephone or FAX machine connection (FXS). ll VIP-2480FS equips twenty-four FXS interfaces telephone set or FAX machine connection (FXS).
Table of Contents Document Objectives........................................................................................ 5 Document Organization..................................................................................... 5 Preparation before beginning administration on VIP-GW....................................... 6 Front Panel LED Indicators & Rear Panels...................................................... 6 LAN/WAN Interface quick configurations.............................................
Document Objectives This guide provides physical installation, LAN/WAN IP configurations, and Internet access establishment information for the PLANET VIP-281/VIP-480/VIP-880/ VIP-1680/VIP-2480 H.323/SIP VoIP Gateway.
Preparation before beginning administration on VIP-GW Front Panel LED Indicators & Rear Panels Front Panel LED State Descriptions PWR On Off GW is power ON GW is power Off CPU (VIP-880/VIP-1680/ VIP-2480 series) Flashing The system is running WAN Port ON Flashing Off GW network connection established Data traffic on cable network Waiting for network connection LAN Port ON Flashing Off LAN is connected successfully Data is transmitting Ethernet not connected to PC FXS ON Flashing Off Telepho
Rear Panel WAN LAN (VIP-880/VIP-1680/ VIP-2480 series) LAN 1 ~ LAN 4 (VIP-281/VIP-480 series) Descriptions The WAN port supports auto negotiating Fast Ethernet 10/100Base-TX networks. This port allows your voice gateway to be connected to an Internet access device, e.g. router, cable modem, ADSL modem, through a CAT.5 twisted pair Ethernet cable. The LAN port supports 1 or 4 10/100Base-TX switch hub networks. These 1/4 ports allow your PC or Switch/Hub to be connected to the voice gateway through a CAT.
Connecting to the telephone patch panel (16-port/24-port model) STEP 1: Attach the 25 port patch panel to the gateway through its RJ-21 connector. STEP 2: The FXS LED indicators at telephone patch panel should be steady ON if the RJ-21 connector is well connected to the gateway and the gateway is powered on.
Web configuration access: To start VIP-GW web configuration, you must have one of these web browsers installed on computer for management • Netscape Communicator 4.03 or higher • Microsoft Internet Explorer 4.01 or higher with Java support Default LAN interface IP address of VIP-GW is 192.168.0.1. You may now open your web browser, and insert 192.168.0.1 in the address bar of your web browser to logon VIP-GW web configuration page.
LAN/WAN Interface quick configurations Nature of PLANET VIP-GW is an IP Sharing (NAT) device, it comes with two default IP addresses, and default LAN side IP address is “192.168.0.1”, default WAN side IP address is “172.16.0.1”. You may use any PC to connect to the LAN port of VIP-GW to start machine administration.
WAN IP address configuration via web configuration interface Execute your web browser, and insert the IP address (default: 172.16.0.1) of VIP in the adddress bar. After logging on machine with username/password (default: admin / 123), browse to “WAN Setting” configuration menu, you will see the configuration screen below: Connection Type Data required. Static IP The ISP will assign IP address, and related information. DHCP Get WAN IP address automatically; it is no need to configure the DHCP settings.
Wizard Setup for Quick Start Wizard Setup After finishing the authentication, the main menu will display 3 parts of configuration, please click “Wizard Setup” to enter quick start: STEP 1: WAN Port Type Setup (Setup First) For most users, internet access is the primary application. The gateway support the WAN interface for Internet access and remote access. The following sections will explain more details of WAN Port Internet access and broadband access setup.
ADSL Dial-Up User (PPPoE Enable) Some ISPs provide DSL-based service and use PPPoE to establish communication link with end-users. If you are connected to the Internet through a DSL line, check with your ISP to see if they use PPPoE. If they do, you need to select this item.
STEP 2: Configuring NAT or Bridge setting Bridge Mode: When working on Bride Mode, the VoIP gateway will use only the LAN setting IP, The VoIP gateway will use the same LAN IP setting as WAN IP. That mean, When Bride mode enable, the WAN connection setting will be ignored. NAT mode: LAN IP Network Configuration IP Address Private IP address for connecting to a local private network (Default: 192.168.0.1) Subnet Mask Netmask for the local private network (Default: 255.255.255.
n Configure the numbering with phone/line ports Phone Number The representation number is the phone number of the telephone that is connected to Phone port Line Number Line ports are connected to the extension ports of the PBX system or the PSTN line. They have a common Line Hunting Group Number. When this number is dialed, the Gateway system will find a free FXO line connected to PBX. This hunting will skip all busy lines and absent lines and find only the idle line to the PBX.
n Outgoing Dialing Plan The purpose of “Outgoing Direct Call” setting is to let user create a proprietary dialing plan when this Gateway is not registered to any H.323 Gatekeeper or any SIP proxy server. This setting can also assign some dialing plan to local ports (including prefix strip, prefix addition). Through this setting, user can directly map a number to a specific gateway (IP address).
n Finishing the Wizard Setup After completing the Wizard Setup, please click “Finish” bottom. The VoIP gateway will save the configuration and rebooting gateway automatically. After 20 Seconds, you could re-login the gateway. Voice communication samples The chapter shows you the concept and command to help you configure your VoIP gateway through sample configuration. And provide several ways to make calls to desired destination in VIP-GW.
FXS port The FXS port allows the connection to an end node, like telephone, fax machine, or out-line of PBX system. FXS port is as like your local phone service provider who provides a number to you. It is easy to tell that after you have connected an end-device to FXS port and you will hear the dial-tone from FXS port once the hand set off-hook. XO FXS 412-1111 222 222 N The FXS port is with voltage and current. DO NOT connects the port to any PBX extension line or PSTN line.
412-1111 222 222 412-1111 PSTN WAN Gateway#1 Gateway#2 SIP VoIP Call: SIP Proxy (Register to SIP IP PBX) mode 100 8100 SIP Call (Register to SIP IP PBX Mode) 100 9100 Phone Register Number List GW1: 801 GW2: 901 IPX-300 Phone SIP IP PBX (172.16.0.
In accordance with account information, please fill related the date of your VoIP gateway in the Number/Account/Password field and enable the Register mode option. Supposing the connection is success, this register status is Success. Meanwhile, please click on the SIP Proxy Configurations, and fill related the date of your VoIP gateway in the Domain/Realm, SIP Proxy Server field. In the SIP proxy case, the Proxy server is 172.16.0.3 and Port number is 5060.