INSTALLATION and USER’S MANUAL GaLiO Fire Pit Corten Natural Gas/Propane-Butane/Propane D2 H2 H1 H H3 D1 [mm] Copyright Planika Sp. z o.o. H H1 H2 H3 D1 D2 650 320 30 300 350 950 www.planikafires.com IG0281#01 02.17.
IT IS OBLIGATORY TO READ AND KEEP THIS INSTRUCTION MANUAL. TABLE OF CONTENTS 1. INTRODUCTION ...........................................................................................................................................................................................3 2. SAFETY INSTRUCTIONS ................................................................................................................................................................................5 2.1 3.
1. INTRODUCTION The GaLiO Fire Pit Corten fireplace is a decorative fuel-effect gas appliances intended only for outdoor use. It is obligatory to acquaint oneself with the below installation manual and user’s manual before committing to the installation and use of the GaLiO Fire Pit Corten fireplace. This manual is to be kept safe for the lifetime of the device. The Planika company designs and manufactures gas devices that meet the highest standards of quality, and safety.
INSTALLATION NOTICE • The installation of this appliance is only to be carried out by an authorized person in accordance with the Manufacturers Instructions, local gas fitting regulations, AS/NZS5601.1 installation code for gas burning appliances and any other relevant statutory regulations. • In all cases the installation of this appliance shall meet the requirements as set out in AS/NZS5601.1 IMPORTANT SAFETY NOTICES • DO NOT PLACE ARTICLES ON OR AGAINST THIS APPLIANCE.
2. SAFETY INSTRUCTIONS • • • • • • • • • • • • Read the instructions before using the appliance. Use outdoors only. The GaLiO Fire Pit Corten fireplace should be installed and serviced annually according to the below installation manual as well as enforced national and local laws regarding gas safety (installation and use). One needs to assess whether the data on the product plaque complies with the local type of gas and pressure.
• The GaLiO Fire Pit Corten fireplace needs to be installed in a place inaccessible for children, unauthorised persons or animals for the direct contact with the flame or hot parts of the device to be impossible. • In case of heavy wind the GaLiO Fire Pit Corten fireplace needs to be immediately turned off and one needs to await until the heavy wind passes. • In case of noticing any sort of gas leaks the fireplace as well as the main valve of the gas cylinder need to be turned off.
3. INSTALLATION 3.1. Box contents • • • • • • • • • • 1x complete GaLiO Fire Pit Corten gas fireplace 1x remote control (if delivered) 1x Touch panel (installed) 4x AA Batteries 2x AAA Batteries (if remote delivered) 4x bag of decorative stones 1x AS/NZS 1869 hose assembly – installed (only LPG version) 1x pressure regulator– installed (only LPG version) 1x installation manual and user’s manual 1x Tempered glass cylinder 3.2.
4. MONTAGE WARNING!!! All elements above the fireplace need to be made of non-flammable materials. • Select a location where the outdoor fire can be supervised during operation. • The outdoor fire is suitable for outdoor use only and must not be used indoors. • An isolation switch must be fitted at the appliance or on an adjacent wall to allow for emergency shutdown and maintenance. • Installation must meet Australian gas codes AS/NZS5601.1-2013.
Gas fire pit minimum height must comply with: • A gas fire pit with a burner less than 1m above the ground must be guarded to the full height of the flame such that a child aged between 2 and 6 years of age cannot gain access to the flame when assessed in accordance with IEC Guide 117. • A guard incorporated into an appliance to comply with requirement 2 (above) must be an integral part of the appliance.
4.1. • • Installation of glass screens • Carefully remove cardboard and foam foil from the glass cylinder. Remove all contaminations from the glass shields which could burn out on the glass during operation of the GaLiO Fire Pit Corten (in particular fingerprints). Protective glass cylinder shall be installed on the top of the burner. • Place glass cylinder on the 3 mounting bracket at secure it gently with the 4 screws • Remove the glass shield only in case of damage of the glass. 4.2.
4.2.2. Connection and replacement of the gas cylinder (LPG version) The GaLiO Fire Pit Corten is delivered together with an AS/NZS 1869 certified hose assembly which, on one end is connected to the valve of the appliance and on the other end to the AS 4621 certified 2.75kPa regulator (POL connection) ready to be connected to the gas cylinder.
5.3. Replacing the batteries If the batteries are inserted incorrectly, the electronics or drive may be irreparably damaged. Only replace the batteries when the appliance has been completely switched off. NOTE: If the appliance is equipped with a 230 VAC connection, no batteries are present in the receiver or in battery box. • The batteries are placed battery holder located at the bottom of Galio Fire Pit Corten. (See Photo 5).
• Screw the cover back and place container back. 5.4. Remote control (if delivered) Galio Fire Pit Insert can be operated by radio remote control. This comprises a hand-held transmitter and a receiver. The receiver is part of the gas control block assembly. • Electrical connections and batteries: o Hand-held transmitter: 2x 1.5V AAA battery o Receiver: 4x1.5V AA battery or 6 VDC • WARNING! Without using a mains adapter, battery replacement is recommended at the beginning of each heating season.
5.4.1. Setting fahrenheit or celsius a. To change between °C and °F, press simultaneously. and buttons NOTE: Choosing °F results in a 12 hour clock. Choosing °C results in a our clock. 5.4.2. Setting the time 1. Press and buttons simultaneously. Day flashes. 2. Press or button to select a number to correspond with the day of the week (e. g. = Monday, = Tuesday, = Wednesday, = Thursday, = Friday, = Saturday, = Sunday). 3. Press and buttons simultaneously. Hour flashes. 4. To select hour press 5.
5.4.4. Switch the Fire ON and OFF Before operating make sure MANUAL knob on the GV60 valve is in the ON, full counter clockwise position. WARNING! When the pilot light is ignited, the motor turns automatically to maximum flame height. If the pilot flame goes out for any reason, wait for 5 minutes before attempting to re-light it. If the pilot does not stay lit after several tries, turn the main valve knob to OFF. 1. Open the valve of the gas cylinder (or gas supply valve in the gas pipe). 2. Press 3. 4.
5.4.5. Stand-by mode (Pilot flame) 1. Press and hold button to set appliance to pilot flame. 5.4.6. Flame height adjustment 1. To increase flame height press and hold button. 2. To decrease flame height or to set appliance to pilot flame, press and hold button. 5.4.7. Flame height directly to minimum position 1. To go to low fire, double-click button. is displayed. NOTE: Flame goes to high fire first before going to low fire. 5.4.8. Flame height directly to maximum position 1.
5.4.9. Countdown timer ON / SETTING: 1. Press and hold button until 2. To select hour press or displayed, and hour flashes. button. button. Minutes flash. 3. To confirm press 4. To select minutes press 5. To confirm press or button. button or wait. OFF: Press button, and countdown time disappear. 5.4.10. Automatic Turn Down To Pilot 3 Hour No Communication Function The valve will turn to pilot flame if there is no communication between handset and receiver for a 3 hour period.
5.5. Touchpad Depending on customers preferences GaLiO Fire Pit Corten Remote may be additionally operated Touch panel. Photo 10: Touch panel To Turn ON Appliance • Press ON-OFF button (see Photo 10) until two short beeps confirm the start sequence has begun; release button. • Once pilot ignition is confirmed, there is main gas flow. Standby Mode (Pilot Flame) • Press and hold (small flame) button to set appliance at pilot flame. To Turn OFF Appliance • Press ON-OFF button.
• Remove the leaks in the identified spaces. • Check for leaks once again. • After the inspection dry the inspected connections. • The device may only be used again after all leaks are removed. • If the problem happens again please contact the dealer. 6.2 Checking the flame appearance. • Burn the GaLiO Fire Pit Corten on max flame height and check the appearance of the flame. Ensure test point pressure is as per the data plate on the appliance and at the end of this manual.
7.2. Glass cylinder cleaning Most of the existing types of smudges may be wiped with a dry cloth. In case of more substantial smudge you may use liquids normally applied to ceramic tiles or windows. Always dry the glass screen to avoid damp patches which could irreversibly embed into the glass. WARNING!!! Avoid leaving fingerprints on the glass. They will be embedded into the glass and you will not be able to clean them. 8.
There are many factors that may affect the malfunction of the gas insert. To exclude a possible fault in the unit or the automatic gas control system, make sure that the fireplace is connected according to these instructions. Below table summarizes possible failures that may occur, possible causes and ways to solve them.
9. PRESSURE ADJUSTMENT Do not attempt to remove screws from the top of gas valve. Do not change any adjustments marked with tamper indicating paint. Motor knob is not to be removed. • Pilot Flame Adjustment The pilot flow adjustment is preset to maximum at the factory. The pilot flame should envelope ⅜ʺ to ½ʺ of the thermocouple o The adjustment screw can be reached through a hole in the MANUAL knob (see figure 21). o Turn the MANUAL knob to the ON position.
• Outlet Pressure Adjustment (High Fire) o Connect a pressure manometer to the valve outlet pressure tap. Pressure tap is opened by turning the screw counterclockwise. Pressure regulator or throttle are located under the cover and can be reached by removing the plug (see figures 21 and 23). o Turn MANUAL knob and main valve knob to the ON position. o Turn pressure regulator adjustment screw to set required burner pressure (high fire).
• Minimum rate Adjustment o Connect a pressure manometer to the valve outlet pressure tap. Pressure tap is opened by turning the screw counterclockwise. Minimum rate adjustment screw is located on the top of the metal valve body. o Turn minimum rate adjustment screw to set required burner pressure (minimum fire). Pressure is increased by turning clockwise (pressure regulator models), or decreased by turning counterclockwise: LPG 0.89kPa, NG 0.
o Take off the cover. o Slightly take out the valve unit from valve box o Unscrew the screw on the test tap by half a turn. A) Inlet pressure tap B) Outlet pressure tap A o Connect the silicon hose from measure device to the measure tap.
o Read the pressure value. Pressure test has to be made when fireplace is turned on with the highest flame level. o Screw tightly the screw on the test tap o Turn on the device and check if screw is sealed using gas detector, foam or other method. o Put on gas valve cover and screw it back.
10.
11.
12. MANUFACTURER’S CONTACT DETAILS Company Name: Planika Sp. z o.o. Address: Bydgoskich Przemysłowców 10 Telephone: + 48 52 364 11 60 13.DISTRIBUTOR’SCONTACT DETAILS Company Name: Address: Telephone: E-mail: Planika Australia 3/2 Cynamide st, Laverton nth, vic 3016, Australia + 61 415 350 564 planikaaustralia@planikafires.
