User's Manual

ManualsBrandsPlantronics ManualsAudio EquipmentWireless Stereo Headphone

The first time you power on your headphones the

pairing process begins.

NOTE If your phone supports Near Field Communication

(NFC) go to NFC pairing (Android).

Holding your headphones, slide the power

switch to the on position. The headphone LEDs

flash red and blue.

GET PAIRED

Activate Bluetooth

on your phone and set it to

search for new devices.

• iPhone

Settings > Bluetooth > On*

• Android

™

> Bluetooth: On > Scan for devices*

*Menus may vary by device.

Select “PLT_BBPRO.”

Once successfully paired, the headset LEDs stop

flashing.

NFC pairing (Android)

Ensure NFC is on and your phone’s display is

unlocked. (Phones may vary.)

Tap and hold the headphones to the phone’s NFC

tag location until NFC pairing completes. If

necessary, accept the connection.

NOTE The headphone’s NFC tag is located on the outside of

the left ear cup. (Phone tag locations vary.)

ANC

TAKE CONTROL

Active Noise Canceling (ANC)

Slide the switch to activate or deactivate ANC.

ANC will block out unwanted noise.

Play/pause music

Tap the Play/pause button on the left ear cup

to play or pause music

Volume

Rotate the volume wheel forward (+) or

backward (–) to control the volume.

Track selection

Rotate the track wheel forward or backward

to control the track selection.

Open mic

While listening to music, you will be able to hear

your surroundings by tapping the Mic button to

activate or deactivate the mic.

Voice enabaled assistant

To activate Siri or Google Voice, press the Call

button for 3 seconds. (Devices may vary.)

Answer or end a call

Tap the Call button on the right ear cup.

Decline a call

Press the Call button for 2 seconds.

Mute

During a conversation, press the Mic button .

You hear “mute on” or “mute off.” While the

microphone is muted, an alert repeats every 15

minutes.

Call back last call

Double-tap the Call button .

It takes up to 2 hours to fully charge your

headphones. The LEDs turn off once charging is

complete.

TIP: To check the headphones battery status, tap the Call

button while wearing your headphones. Headphones

must be in idle state.

Your headphones have up to 24 hours of listening

time.

CHARGE

Summary of content (4 pages)

PAGE 1
TAKE CONTROL GET PAIRED The first time you power on your headphones the pairing process begins. NOTE If your phone supports Near Field Communication (NFC) go to NFC pairing (Android). 1 Holding your headphones, slide the power switch to the on position. The headphone LEDs flash red and blue. R 2 Activate Bluetooth® on your phone and set it to search for new devices. • iPhone® Settings > Bluetooth > On* • Android™ > Bluetooth: On > Scan for devices* *Menus may vary by device.
PAGE 2
NEED MORE HELP? ADJUST THE FIT Find a local support number Adjust the headphones for a comfortable fit Lengthen or shorten the band until it fits comfortably. When not using your headphones, fold the ear cushions in and against your body. plantronics.com/support Read detailed online user guide plantronics.com/documentation PAIR SECOND DEVICE 1 Press and hold the Call button until the LEDs flash red and blue. 2 Activate Bluetooth on your second device and follow steps 2 and step 3 in "Get Paired.
PAGE 3
FCC statement ·This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. ·This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
PAGE 4
NOTE: THE GRANTEE IS NOT RESPONSIBLE FOR ANY CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE. SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT. IC Radiation Exposure Statement for Canada This device complies with Industry Canada licence-exempt RSS standard(s).