VOYAGER™ 510S BLUETOOTH® HEADSET SYSTEM User Guide
VOYAGER™ 510S SYSTEM DIAGRAMS 2 Telephone receiver jack Speak volume major adjust switch Telephone cord AC adapter jack Handset lifter (optional) Handset lifter jack Telephone cord jack AC adapter Call control button & talk/on line indicator light Power indicator light (red) Charge indicator light (amber) Configuration dial Charging cradle Speak volume fine adjust buttons Listen volume major adjust switch Handset Lifter on/off switch
VOYAGER™ 510S SYSTEM DIAGRAMS & CONNECTING YOUR BASE Back Power/mute button Outside Listen volume adjust +/– buttons Horizontal boom adjust Status indicator light (red/blue) Eartip Microphone Call control button Charge connection AC adapter CONNECTING YOUR VOYAGER 510S BASE 1. Connect telephone receiver cord to receiver jack in the Voyager 510S Bluetooth® Headset System base (referred to as “base“ from this point on). Note: The access to the receiver jack is fairly small. 2.
BASIC INFORMATION This User Guide provides instructions on the installation and usage of your Voyager™ 510S Bluetooth® Headset System. Note: The headset can also be used with other Bluetooth audio devices. See page 6 for cell phone pairing instructions. For safety and regulatory information, please refer to the separate “Important Safety and Regulatory Information” booklet. A copy of the Declaration of Conformity can be found at www.plantronics.com/documentation.
BASIC INFORMATION 5 FITTING THE HEADSET Slide the headset over and behind your ear. Then, press gently towards your ear for a snug fit. Adjust the microphone position so that it is directed towards your mouth as illustrated. POWERING THE HEADSET ON AND OFF To turn the headset on, press and hold the power/mute button for 3 seconds until the status indicator flashes blue. To turn off, press and hold the button again for 3 seconds until the status indicator flashes red.
PAIRING PAIRING HEADSET AND BASE The Voyager™ 510S Bluetooth® Headset System is supplied with the headset and base unit factory paired to each other. However, if you have purchased a base unit separately, or if you wish to use a replacement headset with your existing base unit, the units must be paired as follows: 1. On the base, press and hold both speak volume fine adjust buttons until the blue talk/on line indicator light and red power indicator light (on the front of unit) start to flash. 2.
PLACING & ANSWERING A CALL 7 A B PLACING A CALL ANSWERING A CALL Desk telephone: Lift phone receiver and then press the call control button on either the headset (A) or base unit (B). When you hear the dial tone, dial number using telephone keypad. If you do not obtain a dial tone, check that the configuration dial is set correctly as described on page 5. Desk telephone: Lift the telephone’s receiver. Press the call control button on either the headset (A) or base (B) to answer the call.
VOLUME & MUTE A B LISTEN VOLUME - HOW OTHERS SOUND TO YOU 1. Adjust the listen volume adjust +/– button (A) to a comfortable level. 2. If you cannot find a comfortable listen level, try different settings (1–4) on the listen volume major adjust switch (B) as shown until a satisfactory sound level is experienced. Note: This setting only adjusts the headset listen level on calls placed using the desk telephone and cannot adjust the headset listen volume when used with a mobile phone.
HANDSET LIFTER (OPTIONAL) 9 OPERATION WITH THE HANDSET LIFTER ACCESSORY The Plantronics Handset Lifter is an accessory that has two functions: • To automatically notify you when an incoming call is detected even when you are away from your desk. • To lift or replace the telephone handset from its cradle even when you are away from your desk. SETTING UP THE HANDSET LIFTER 1. Plug lifter power cord into handset lifter jack on base. 2. Set handset lifter on/off switch on base to “on” (down) position.
HANDSET LIFTER (OPTIONAL) MAKING AND RECEIVING CALLS WITH LIFTER INSTALLED 1. To make a call, press call control button on headset or base to raise lifter. Use telephone keypad to dial the number. When call is complete, press call control button to lower lifter (phone will hang up). or 2. To receive a call, when telephone rings, press call control button on headset or base to raise lifter and receive call. When call is complete, press call control button to lower lifter (phone will hang up).
AUDIBLE WARNINGS, MAINTENANCE & ACCESSORIES 11 OUT OF RANGE WARNING As you walk away from the base unit you will eventually reach the system operating range limit. The system will issue audible warnings at the operating limit. If not in a call: One low tone when edge of range reached. One high tone when back in range. If in a call: One low tone when edge of range reached. One high tone followed by a triple tone when back in range.
TROUBLESHOOTING I plugged everything in but the lights won’t come on. POSSIBLE CAUSE SOLUTION No power Check that the AC adapter is connected to the base unit. Check that the AC adapter is connected to the wall outlet. Check that the AC adapter is the model supplied by Plantronics. My headset does not work with the base unit.
TROUBLESHOOTING 13 I tried all four positions on the configuration dial and cannot hear a dial tone in any position. POSSIBLE CAUSE SOLUTION Headset system is not connected correctly Check that the telephone is connected to the base unit’s telephone cord jack. Check that the telephone receiver is connected to the base unit’s telephone receiver jack. You may have an incompatible phone Call your supplier or local Plantronics office for help.
REGULATORY NOTICE EXPOSURE TO RADIO FREQUENCY RADIATION The radiated output power of this internal wireless radio is far below the FCC radio frequency exposure limits. Nevertheless, the wireless radio shall be used as described in the manual. The internal wireless radio operates within guidelines found in radio frequency safety standards and recommendations, which reflect the consensus of the scientific community. Plantronics therefore believes the internal wireless radio is safe for use by consumers.
PRODUCT REGISTRATION 15 REGISTER YOUR PRODUCT ONLINE PLANTRONICS TECHNICAL ASSISTANCE CENTER This is not a condition of your warranty, but will assist us in providing the best possible service and technical support for your product. For assistance and accessibility information, call the Plantronics Technical Assistance Center (TAC) 800-544-4660 x5538, or visit our website at www.plantronics.com. Visit www.plantronics.com/ productregistration.
