Users Manual Part 2

QUICK START
CA22CD
PUSH-TO-TALK HEADSET AMPLIFIER
©
2020 Plantronics, Inc. All rights reserved. Poly, the propeller design, and the Poly
logo
are trademarks of Plantronics, Inc. All other trademarks are the property of their
respective owners. Manufactured by Plantronics, Inc.
215720-03 11.20
CA22CD has a CA22CD base, (may be followed by /A or /S) and a CA22CDSY/
CA22CDDY remote (may be followed by /A or /S).
headset not included
poly.com/support
Support
Settings
Plus / Minus
Check / Delete
Daisy Chain / Link
Lock
General
Indicator Light
Music
ANC
Timer
Scaled to 45% of full size
REMOTE BOTTOM OF BASE
Rocker switch
PTT button
ENGLISH
CONNECT YOUR SYSTEM
U
sing the diagram, connect your system. Diagram shows a
typical installation. Alternative USB port on back of the base
can be used.
CHARGE YOUR REMOTE
Charge the remote and spare battery for a minimum of 1 hour
by placing them in the base. The base LED flashes when
charging and remains on when fully charged. Allow 4 hours for
full charge.
ADJUST THE VOLUME CONTROLS
Default volume settings
Position 4 is the default setting for Talk and Listen coarse-
adjust switches on the bottom of the base and correct for most
applications.
Adjust Talk volume
Talk-course adjust switch position corresponds to your console’s
mi
crophone input for (1) dynamic-, (2 & 3) electret-, or (4) carbon-
mic applications.
1 Adjust the Talk
switch to the next lowest or highest position
un
til your caller can hear you clearly.
2 Press Talk Volume + or - buttons on the top of base to fine-tune
your talk volume.
Adjust Listen volume
1 Adjust the Listen
switch to the next lowest or highest position
un
til you can hear the caller clearly.
2 Toggle the rocker switch on the remote to fine-tune your listen
volume.
Prevent echoes
Excessively high audio levels can result in distortion and or/echo.
Adjust your equipment's volume controls as described below.
1 Turn off or completely decrease your equipment's sidetone control
(if present).
2 Set the console receiver and microphone volumes to mid-range.
ADJUST THE HEADSET MICROPHONE
For the best sound position boom so that the microphone is
two finger-widths from the corner of your mouth.
KEY UP RADIO
Press the Push To Talk (PPT) button on the remote to key up
your radio; the Talk LED on the base turns green.
MANAGE BATTERIES
Swap battery every 4 hours
A fully-charged battery powers your remote for 8 hours, however,
we recommend swapping batteries every 4 hours.
IMPORTANT Swapping batteries every 4 hours maximizes the battery life and
ensures communications are not interrupted by low batteries.
Low battery warning
Recharge your battery if you hear a single beep every 10 seconds.
Turn off audio link when charging or not in use
If left to charge with the link up, a new charging cycle begins about
3 hours after first charge. Using the remote at this time could
result in reduced talk time.
Battery storage
Remove battery pack from remote when storing to prevent the
battery from depleting.
Replace batteries
Monitor the performance of your batteries for gradually decreasing
talk times and replace as needed.
NOTE Rechargeable batteries of all types gradually age and lose their ability to
give and receive charge.
STAY WITHIN RANGE OF YOUR BASE
A triple beep warns you if your remote is out of range and has
lost its audio link with the base.
NEED MORE HELP?
View complete user guide: poly.com/support
DANSK
CONNECT YOUR SYSTEM
U
s
ing the diagram, connect your system. Diagram shows a
typical installation. Alternative USB port on back of the base
can be used.
CHARGE YOUR REMOTE
Charge the remote and spare battery for a minimum of 1 hour
by placing them in the base. The base LED flashes when
charging and remains on when fully charged. Allow 4 hours for
full charge.
ADJUST THE VOLUME CONTROLS
Default volume settings
Position 4 is the default setting for Talk
and Listen coarse-
a
d
just switches on the bottom of the base and correct for most
applications.
Adjust Talk volume
Talk-course adjust
switch position corresponds to your console’s
mi
crophone input for (1) dynamic-, (2 & 3) electret-, or (4) carbon-
mic applications.
1 Adjust the Talk
switch to the next lowest or highest position
un
til your caller can hear you clearly.
2 Press Talk Volume + or - buttons on the top of base to fine-tune
your talk volume.
Adjust Listen volume
1 Adjust the Listen
switch to the next lowest or highest position
un
til you can hear the caller clearly.
2 Toggle the rocker switch on the remote to fine-tune your listen
volume.
Prevent echoes
Excessively high audio levels can result in distortion and or/echo.
Adjust your equipment's volume controls as described below.
1 Turn off or completely decrease your equipment's sidetone control
(if present).
2 Set the console receiver and microphone volumes to mid-range.
ADJUST THE HEADSET MICROPHONE
For the best sound position boom so that the microphone is
two finger-widths from the corner of your mouth.
KEY UP RADIO
P
r
ess the Push To Talk (PPT) button on the remote to key up
your radio; the Talk LED on the base turns green.
MANAGE BATTERIES
Swap battery every 4 hours
A fully-charged battery powers your remote for 8 hours, however,
we recommend swapping batteries every 4 hours.
IMPORTANT Swapping batteries every 4 hours maximizes the battery life and
ensures communications are not interrupted by low batteries.
Low battery warning
Recharge your battery if you hear a single beep every 10 seconds.
Turn off audio link when charging or not in use
If left to charge with the link up, a new charging cycle begins about
3 hours after first charge. Using the remote at this time could
result in reduced talk time.
Battery storage
Remove battery pack from remote when storing to prevent the
battery from depleting.
Replace batteries
Monitor the performance of your batteries for gradually decreasing
talk times and replace as needed.
NOTE Rechargeable batteries of all types gradually age and lose their ability to
give and receive charge.
STAY WITHIN RANGE OF YOUR BASE
A triple beep warns you if your remote is out of range and has
lost its audio link with the base.
BRUG FOR MERE HJÆLP?
Se komplet brugervejledning: poly.com/support
DEUTSCHE
CONNECT YOUR SYSTEM
U
s
ing the diagram, connect your system. Diagram shows a
typical installation. Alternative USB port on back of the base
can be used.
CHARGE YOUR REMOTE
Charge the remote and spare battery for a minimum of 1 hour
by placing them in the base. The base LED flashes when
charging and remains on when fully charged. Allow 4 hours for
full charge.
ADJUST THE VOLUME CONTROLS
Default volume settings
Position 4 is the default setting for Talk
and Listen coarse-
a
d
just switches on the bottom of the base and correct for most
applications.
Adjust Talk volume
Talk-course adjust
switch position corresponds to your console’s
mi
crophone input for (1) dynamic-, (2 & 3) electret-, or (4) carbon-
mic applications.
1 Adjust the Talk
switch to the next lowest or highest position
un
til your caller can hear you clearly.
2 Press Talk Volume + or - buttons on the top of base to fine-tune
your talk volume.
Adjust Listen volume
1 Adjust the Listen
switch to the next lowest or highest position
un
til you can hear the caller clearly.
2 Toggle the rocker switch on the remote to fine-tune your listen
volume.
Prevent echoes
Excessively high audio levels can result in distortion and or/echo.
Adjust your equipment's volume controls as described below.
1 Turn off or completely decrease your equipment's sidetone control
(if present).
2 Set the console receiver and microphone volumes to mid-range.
ADJUST THE HEADSET MICROPHONE
For the best sound position boom so that the microphone is
two finger-widths from the corner of your mouth.
KEY UP RADIO
P
r
ess the Push To Talk (PPT) button on the remote to key up
your radio; the Talk LED on the base turns green.
MANAGE BATTERIES
Swap battery every 4 hours
A fully-charged battery powers your remote for 8 hours, however,
we recommend swapping batteries every 4 hours.
IMPORTANT Swapping batteries every 4 hours maximizes the battery life and
ensures communications are not interrupted by low batteries.
Low battery warning
Recharge your battery if you hear a single beep every 10 seconds.
Turn off audio link when charging or not in use
If left to charge with the link up, a new charging cycle begins about
3 hours after first charge. Using the remote at this time could
result in reduced talk time.
Battery storage
Remove battery pack from remote when storing to prevent the
battery from depleting.
Replace batteries
Monitor the performance of your batteries for gradually decreasing
talk times and replace as needed.
NOTE Rechargeable batteries of all types gradually age and lose their ability to
give and receive charge.
STAY WITHIN RANGE OF YOUR BASE
A triple beep warns you if your remote is out of range and has
lost its audio link with the base.
BENÖTIGEN SIE WEITERE HILFE?
Siehe vollständiges Benutzerhandbuch: poly.com/support
ESPAÑOL
CONNECT YOUR SYSTEM
U
s
ing the diagram, connect your system. Diagram shows a
typical installation. Alternative USB port on back of the base
can be used.
CHARGE YOUR REMOTE
Charge the remote and spare battery for a minimum of 1 hour
by placing them in the base. The base LED flashes when
charging and remains on when fully charged. Allow 4 hours for
full charge.
ADJUST THE VOLUME CONTROLS
Default volume settings
Position 4 is the default setting for Talk
and Listen coarse-
a
d
just switches on the bottom of the base and correct for most
applications.
Adjust Talk volume
Talk-course adjust
switch position corresponds to your console’s
mi
crophone input for (1) dynamic-, (2 & 3) electret-, or (4) carbon-
mic applications.
1 Adjust the Talk
switch to the next lowest or highest position
un
til your caller can hear you clearly.
2 Press Talk Volume + or - buttons on the top of base to fine-tune
your talk volume.
Adjust Listen volume
1 Adjust the Listen
switch to the next lowest or highest position
un
til you can hear the caller clearly.
2 Toggle the rocker switch on the remote to fine-tune your listen
volume.
Prevent echoes
Excessively high audio levels can result in distortion and or/echo.
Adjust your equipment's volume controls as described below.
1 Turn off or completely decrease your equipment's sidetone control
(if present).
2 Set the console receiver and microphone volumes to mid-range.
ADJUST THE HEADSET MICROPHONE
For the best sound position boom so that the microphone is
two finger-widths from the corner of your mouth.
ESPAÑOL
KEY UP RADIO
P
ress the Push To Talk (PPT) button on the remote to key up
your radio; the Talk LED on the base turns green.
MANAGE BATTERIES
Swap battery every 4 hours
A fully-charged battery powers your remote for 8 hours, however,
we recommend swapping batteries every 4 hours.
IMPORTANT Swapping batteries every 4 hours maximizes the battery life and
ensures communications are not interrupted by low batteries.
Low battery warning
Recharge your battery if you hear a single beep every 10 seconds.
Turn off audio link when charging or not in use
If left to charge with the link up, a new charging cycle begins about
3 hours after first charge. Using the remote at this time could
result in reduced talk time.
Battery storage
Remove battery pack from remote when storing to prevent the
battery from depleting.
Replace batteries
Monitor the performance of your batteries for gradually decreasing
talk times and replace as needed.
NOTE Rechargeable batteries of all types gradually age and lose their ability to
give and receive charge.
STAY WITHIN RANGE OF YOUR BASE
A triple beep warns you if your remote is out of range and has
lost its audio link with the base.
¿NECESITA MÁS AYUDA?
Ver la guía del usuario completa: poly.com/support
SUOMALAINEN
CONNECT YOUR SYSTEM
U
sing the diagram, connect your system. Diagram shows a
typical installation. Alternative USB port on back of the base
can be used.
CHARGE YOUR REMOTE
Charge the remote and spare battery for a minimum of 1 hour
by placing them in the base. The base LED flashes when
charging and remains on when fully charged. Allow 4 hours for
full charge.
ADJUST THE VOLUME CONTROLS
Default volume settings
Position 4 is the default setting for Talk and Listen coarse-
adjust switches on the bottom of the base and correct for most
applications.
Adjust Talk volume
Talk-course adjust switch position corresponds to your console’s
mi
crophone input for (1) dynamic-, (2 & 3) electret-, or (4) carbon-
mic applications.
1 Adjust the Talk
switch to the next lowest or highest position
un
til your caller can hear you clearly.
2 Press Talk Volume + or - buttons on the top of base to fine-tune
your talk volume.
Adjust Listen volume
1 Adjust the Listen
switch to the next lowest or highest position
un
til you can hear the caller clearly.
2 Toggle the rocker switch on the remote to fine-tune your listen
volume.
Prevent echoes
Excessively high audio levels can result in distortion and or/echo.
Adjust your equipment's volume controls as described below.
1 Turn off or completely decrease your equipment's sidetone control
(if present).
2 Set the console receiver and microphone volumes to mid-range.
ADJUST THE HEADSET MICROPHONE
For the best sound position boom so that the microphone is
two finger-widths from the corner of your mouth.
KEY UP RADIO
Press the Push To Talk (PPT) button on the remote to key up
your radio; the Talk LED on the base turns green.
MANAGE BATTERIES
Swap battery every 4 hours
A fully-charged battery powers your remote for 8 hours, however,
we recommend swapping batteries every 4 hours.
IMPORTANT Swapping batteries every 4 hours maximizes the battery life and
ensures communications are not interrupted by low batteries.
Low battery warning
Recharge your battery if you hear a single beep every 10 seconds.
Turn off audio link when charging or not in use
If left to charge with the link up, a new charging cycle begins about
3 hours after first charge. Using the remote at this time could
result in reduced talk time.
Battery storage
Remove battery pack from remote when storing to prevent the
battery from depleting.
Replace batteries
Monitor the performance of your batteries for gradually decreasing
talk times and replace as needed.
NOTE Rechargeable batteries of all types gradually age and lose their ability to
give and receive charge.
STAY WITHIN RANGE OF YOUR BASE
A triple beep warns you if your remote is out of range and has
lost its audio link with the base.
TARVITSETKO OHJEITA?
Tutustu käyttöohjeeseen kokonaisuudessaan: poly.com/support
FRANÇAIS
CONNECT YOUR SYSTEM
U
sing the diagram, connect your system. Diagram shows a
typical installation. Alternative USB port on back of the base
can be used.
CHARGE YOUR REMOTE
Charge the remote and spare battery for a minimum of 1 hour
by placing them in the base. The base LED flashes when
charging and remains on when fully charged. Allow 4 hours for
full charge.
ADJUST THE VOLUME CONTROLS
Default volume settings
Position 4 is the default setting for Talk and Listen coarse-
adjust switches on the bottom of the base and correct for most
applications.
Adjust Talk volume
Talk-course adjust switch position corresponds to your console’s
mi
crophone input for (1) dynamic-, (2 & 3) electret-, or (4) carbon-
mic applications.
1 Adjust the Talk
switch to the next lowest or highest position
un
til your caller can hear you clearly.
2 Press Talk Volume + or - buttons on the top of base to fine-tune
your talk volume.
Adjust Listen volume
1 Adjust the Listen
switch to the next lowest or highest position
un
til you can hear the caller clearly.
2 Toggle the rocker switch on the remote to fine-tune your listen
volume.
Prevent echoes
Excessively high audio levels can result in distortion and or/echo.
Adjust your equipment's volume controls as described below.
1 Turn off or completely decrease your equipment's sidetone control
(if present).
2 Set the console receiver and microphone volumes to mid-range.
ADJUST THE HEADSET MICROPHONE
For the best sound position boom so that the microphone is
two finger-widths from the corner of your mouth.
KEY UP RADIO
Press the Push To Talk (PPT) button on the remote to key up
your radio; the Talk LED on the base turns green.
MANAGE BATTERIES
Swap battery every 4 hours
A fully-charged battery powers your remote for 8 hours, however,
we recommend swapping batteries every 4 hours.
IMPORTANT Swapping batteries every 4 hours maximizes the battery life and
ensures communications are not interrupted by low batteries.
Low battery warning
Recharge your battery if you hear a single beep every 10 seconds.
Turn off audio link when charging or not in use
If left to charge with the link up, a new charging cycle begins about
3 hours after first charge. Using the remote at this time could
result in reduced talk time.
Battery storage
Remove battery pack from remote when storing to prevent the
battery from depleting.
Replace batteries
Monitor the performance of your batteries for gradually decreasing
talk times and replace as needed.
NOTE Rechargeable batteries of all types gradually age and lose their ability to
give and receive charge.
STAY WITHIN RANGE OF YOUR BASE
A triple beep warns you if your remote is out of range and has
lost its audio link with the base.
BESOIN DE PLUS D'INFORMATIONS ?
Afficher le guide de l'utilisateur complet : poly.com/support