5 Easy Steps The fastest way to setup your CS70 Headset System Base Power Adaptor HL10 Automatic Handset Lifter* CS70 Headset with Ear Tip CS70 Headset Base *Not included in all configurations CS70 Series S e t u p G u i d e
CS70 Package Contents Headset Setup Guide Headset Base with Preinstalled Phone Cable Base Power Adapter Ear Tips Please refer to the separate Safety Instructions sheet for important product safety information prior to installation or use of the product. CS70 With Handset Lifter* Adds: HL10 User Guide HL10 Automatic Handset Lifter *Automatic Handset Lifter is bundled with certain CS70 configurations and also available separately.
STEP 1 Install Ear Tip & Adjust fit Fit the Headset Slide the headset over and behind your ear, then press gently toward your ear. Rotate the microphone boom until it is pointed toward your mouth. If the ear tip is uncomfortable, install a different ear tip. See below. For your safety and comfort, the ear tip should never be inserted into the ear canal. To Install a Different Ear Tip Remove the pre-installed ear tip by pushing in and turning the ear tip clockwise, then pull firmly.
STEP 2 Connect Base to Desk Phone Use Configuration A if: You will use the Automatic Handset Lifter or… Your phone has NO built-in headset functionality (no Headset button). Configuration A 1. Unplug the handset coil cord from the desk phone handset port [A], then plug it into the green labeled handset port [B] on the Headset Base. A Handset Coil Cord Handset Headset Base (bottom view) A B 2.
Use Configuration B if: You will NOT use the Automatic Handset Lifter and… Your phone has built-in headset functionality (a Headset button). Configuration B Confirm there is a “Headset” button on your phone Headset Base (bottom view) C 1. Plug the short BLACK Phone Cable that is pre-installed on the Headset Base into the Heaset port [C] on the desk phone.
STEP 3 Connect Power and Charge Headset A. Connect Headset Base to power outlet 1. Plug the Base Power Adapter into a wall outlet, then plug the power cord into the yellow labeled connector on the bottom of the Headset Base. The red Power light on the left front of the Headset Base will turn on. (See illustration at bottom of page.) Insert into yellow labeled power connection on Headset Base as shown to charge. Base Power Adapter Headset Base (bottom view) B.
STEP 4 Install Automatic Handset Lifter If you do not have the Lifter, skip to step 5. Why use a handset lifter? The lifter greatly simplifies using a headset with your desk phone. It lets you answer and end calls without being near your phone. The HL10 Automatic Handset lifter is included with certain CS70 configurations and is also available separately. A. Connect Handset Lifter power cord to Headset Base 1.
B. Determine Lifter position and height setting 1. Set the Lifter Height Switch to the lowest setting. Handset Lifter Arm Lifter viewed from back Start with Lifter Height Switch in lowest position 2. While wearing your headset, slide the Handset Lifter Arm under the handset until the lifter base touches the side of the phone. 3. Slide the Lifter up to where it nearly touches the handset earpiece. Slide Lifter under handset, then up toward the ear piece 4. Press the Call Control Button on the headset.
6. Check the Lifter height adjustment by moving the Lifter Height Switch to a higher position. Repeat steps 2. through 4. as necessary. If you hear a dial tone, the lifter height is now set correctly. Please continue with the next section “Mount the Lifter in Permanent Position”. 7. If you still cannot hear a dial tone, Configuration you will need to change the setting Dial on the Configuration Dial. Using a coin or paperclip, turn the Configuration Dial to a different setting until you hear a dial tone.
STEP 5 Make a Test Call to Configure and Optimize your System. To get the best sound quality for both you and your listeners You MUST configure and optimize your system! A. Make the test call 1. If your desk phone has a volume control, set it to mid-range. 2. If you have installed the Automatic Handset Lifter, press the Call Control Button on your headset.
B. Set the Configuration Dial Once you have dialed the Automated Sound Test, follow the prompts to find the setting that gives you the clearest sound. Use a coin or large paperclip to turn the Configuration Dial. Configuration Dial Position Indicator Multiple settings might work with your phone; however, only one is the optimal position. C. Set Listening Volume While listening to the Automated Sound Test, adjust the listening volume by using the Listening Volume Switch on the back of the Base.
Using your CS70 Headset System Powering up the Headset If the headset battery is charged and the base is connected to power, the headset is automatically on.
To Fine Tune Listening Volume Press [+] to increase. You will hear ascending tones and two tones at the limit. Press [–] to decrease. You will hear descending tones and two tones at the limit. Listening Volume Button To Fine Tune Speaking Volume While on a call, you can adjust your speaking volume by using the Speaking Volume Minor Adjustment Control on the back of the base. Listening volume can be adjusted on the headset.
CS70 Lights and Tones Indicator Lights Talking/Muted (green) Power (red) Charging (amber) Base Status Base Light Power on Solid red Headset charging Flashing amber Headset fully charged Solid amber Headset in talk mode Solid green Headset in mute mode Flashing green Headset Status Headset Light Headset in talk mode Flashing amber Tones Out of Range Warning: If you walk out of range of your base, your headset will issue audible tones at its operating limit.
Troubleshooting and Common Questions I can’t hear a dial tone at the headset • Make sure your headset is charged. • Press the Call Control Button on your headset. • Make sure the lifter is lifting the handset high enough to operate the hookswitch; set to a higher setting if necessary. • Adjust the Configuration Dial on the left side of the base. Align the “1” on the dial with the ridges to the right side of the dial. If there is no dial tone for setting “1” try the other dial settings.
Plantronics Limited Warranty • This warranty covers defects in materials and workmanship of products manufactured, sold or certified by Plantronics which were purchased and used in the United States. • This warranty lasts for one year from the date of purchase of the products. • This warranty extends to you only if you are the end user with the original purchase receipt. • We will, at our option, repair or replace the products that do not conform to the warranty.