Savi™ Talk WT100/T Professional wireless headset system (WT1/T base + WH100/T headset) with optional HL10 lifter User Guide
Welcome Congratulations on purchasing your new Plantronics product. This guide contains instructions for setting up and using your Savi Talk professional wireless headset system.
Contents 1 Package contents and features................................... 4 1.1 Base.......................................................................... 4 6 Using your Savi Talk professional wireless headset system . .................................................................... 12 1.2 Savi WH100/T headset............................................. 5 Powering headset on/off............................................... 12 1.3 HL10 lifter and features (optional).........................
1 Package contents and features 1.
1.
1.
2 Base set-up 2.1 Attaching charging cradle to base 2.3 Connecting power supply to base 1 Connect the headset charging cradle to the base. Push 1 Connect the base power supply into the power jack on firmly on the cradle until the cradle snaps into place. the base. 2 Connect the power supply to outlet. The power indicator light will be solid red. 2.2 Connecting base to desk phone 1 Connect the telephone interface cable to the telephone interface cable jack on the base.
3 Headset set-up 3.1 Fitting headset 3.2 Docking and charging the headset The headset comes with a pre-installed ear loop. An optional headband is also provided. 1 Gently push the headset into the charging cradle. 1 To install the headband, gently unsnap the pre-installed ear loop from the headset. The indicator light on the headset will be solid red to indicate that the headset battery is charging 2 Charge for at least 20 minutes prior to the first use. 2 Snap the headband into the headset.
4 Configuration and test call 4.1 Checking configuration 5 Adjust the master listening volume on base. A setting of 2 or 3 is ideal. 1 Set volume on desk phone to mid-range. 2 Remove handset from desk phone cradle. 3 With your headset on, press the call control button on the headset. 4 Listen for a normal dial tone. If you hear a dial tone and the dial tone sounds normal, continue with Step 4.2 Making a test call.
5 Lifter set-up (optional) 5.1 Installing lifter 7 Gently place the lifter on the desk phone in the predetermined position. 8 Press firmly to adhere. Handset lifter power cord 1 Firmly press the handset lifter power cord into the handset lifter jack. 2 While wearing your headset, slide the handset lifter arm under the handset until the lifter base touches the side of the phone. 3 Slide the lifter up to where it nearly touches the handset 5.
5.3 Additional parts (if required) Ringer microphone Extender arm 2 1 3 1 Stabilisers 2 2 Use ringer microphone when the telephone speaker is not located directly under the handset. 1 Remove cover from ringer microphone jack on back of lifter. 2 Connect ringer microphone plug. Use extender arm when the handset lifter needs additional stability lifting and returning handset to cradle. 3 Place ringer microphone over phone speaker. Remove adhesive tape and attach.
6 Using your Savi Talk professional wireless headset system For your safety, do not use headset at high volumes for extended periods of time. Doing so can cause hearing loss. Always listen at moderate levels. For more information on headsets and hearing, visit: www.plantronics.com/healthandsafety Note: If your desk phone has a volume control, set it to midrange. Call control button Powering headset on/off The headset will be ready to use once it has been charged in the base as described in Section 3.2.
Talk indicator light Muting a call To mute a call, push and hold the headset volume down button for two seconds. You will hear a low/high tone pair indicating the mute is activated. The talk indicator light on the base will flash blue. Power indicator light To un-mute a call, push and hold the headset volume down button for two seconds. You will hear a high/low tone pair indicating the mute is deactivated. The talk indicator light on the base will be solid blue.
Out of range warning Subscription If you are on a call, you will hear the audio degrade as you move out of range. The headset and base unit are supplied subscribed to each other. However, if you wish to use a replacement headset with your existing base, the units can be subscribed to each other by the following method: If you stay out of range, active calls will be suspended. Calls will be re-established when you walk back into range.
7 Troubleshooting and common questions I can't hear a dial tone at the headset. Make sure your headset is charged. Make sure your headset is subscribed to base. See page 14. Press the call control button on your headset. Make sure the lifter is lifting the handset high enough to operate the hookswitch; set to a higher setting if necessary. Adjust the configuration switch on the base until a dial tone is heard. Fine-tune the listening volume with the call control button.
FCC Regulatory Information This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
