MSDS

ManualsBrandsPlasti Dip ManualsPaint11 oz. Red Rubber Coating Spray (6-Pack)

*Estimate

N/A-Not Applicable

N/R-Not Restricted

N/E-Not Established

MATERIAL SAFETY DATA SHEET

NOTE: BLANK SPACES ARE NOT PERMITTED. IF ANY ITEM IS NOT APPLICABLE, THE SPACE MUST BE MARKED TO INDICATE THAT.

IDENTITY

(As shown on Label or package) PLASTI DIP SPRAY (ALL COLORS)

PART NO.

IF APPLICABLE

SECTION I

MANUFACTURER'S

NAME Plasti Dip International Inc.

EMERGENCY PHONE No.

USA only: 1-800-424-9300 INT’L: 703-527-3887

ADDRESS (NUMBER, STREET, CITY, STATE AND ZIP CODE)

3920 Pheasant Ridge Drive

REVISION # 0004

Blaine, MN 55449

MANUFACTURER'S PHONE

No. FOR INFORMATION 1-763-785-2156

DATE MSDS

WAS PREPARED February 2, 2010

SECTION II - HAZARDOUS INGREDIENTS INFORMATION. All Health Hazards which comprise 1% or greater of the composition and all

carcinogens if 0.1% of the composition or greater.

HAZARDOUS COMPONENTS CHEMICAL and

IDENTITY AND COMMON NAME (S)

% Wt.

(OPTIONAL)

CAS NO. OSHA

PEL

ACGIH

TLV

OTHER LIMITS

RECOMMEND

Propane 25-27 74-98-6 1000 ppm 1000 ppm None

VM&P Naphtha 23-25 64742-89-8 300 ppm 300 ppm None

Heptane 13-15 426260-76-6 500 ppm 400 ppm None

N-Butane 8-10 106-97-8 800 ppm 800 ppm None

Xylene 5-7 1330-20-7 100 ppm 100 ppm None

Methyl Ethyl Ketone 2-4 78-93-3 200 ppm 200 ppm None

Methyl n-Amyl Ketone 2-4 110-43-0 100 ppm 50 ppm None

Ethylbenzene 1-2 100-41-4 100 ppm 100 ppm None

Carbon Black (Black Only) 0.1-1 1333-86-4 3.5 mg/m

3.5 mg/m

None

SECTION III - PHYSICAL / CHEMICAL CHARACTERISTICS

BOILING

POINT <1 – 285 °F

SPECIFIC GRAVITY (H

0 =1)

0.675

APPROXIMATE WEIGHT PER GALLON (LBS)

5.57

VAPOR PRESSURE

760 mm Hg @ 20 °C

VAPOR DENSITY

(AIR = 1) Heavier than Air

EVAPORATION RATE

(BUTYL ACETATE =1) >4.6

SOLUBILITY IN WATER

N/A

% VOLATILE

87..2957%

OTHER

(IF ANY)

APPEARANCE

AND ODOR Various colors, syrupy liquid, with solvent odor

SECTION IV-FIRE AND EXPLOSION HAZARD DATA

FLASH POINT

Propellant < -25 °F

FLAMMABLE LIMITS

LEL

0.9

UEL

11.5

EXTINGUISHING

MEDIA Carbon Dioxide, Dry Chemical, or Foam

SPECIAL FIRE FIGHTING

PROCEDURES Self contained breathing apparatus with a full face piece, operated in pressure demand or other positive pressure mode.

UNUSUAL FIRE AND This material is flammable and may be ignited by heat, sparks, flame or static electricity.

EXPLOSION HAZARDS Level 3 aerosol (NFPA 30B). Contents under pressure if heated over 120°F aerosol can could explode, even when empty.

HAZARDOUS PRODUCTS FORMED BY

FIRE OR THERMAL DECOMPOSITION Carbon Dioxide and/or Carbon Monoxide

EXPLOSIVE LIMITS

(% BY VOLUME IN AIR) 0.9 – 11.5

SECTION V - OPTIONAL HAZARD RATINGS IDENTIFICATION

HAZARD RATING

4-EXTREME

3-HIGH

2-MODERATE

1-SLIGHT

0-INSIGNIFICANT

**SEE SECTION IV

National Fire Protection Association (NFPA)

FIRE 4

REACTIVITY 0 .

HEALTH 2

SPECIAL HAZARDS NONE .

This is the "front" when printed in duplex. Page 1 of 2 pages if not duplex.

Summary of content (2 pages)

PAGE 1
*Estimate N/A-Not Applicable N/R-Not Restricted N/E-Not Established MATERIAL SAFETY DATA SHEET NOTE: BLANK SPACES ARE NOT PERMITTED. IF ANY ITEM IS NOT APPLICABLE, THE SPACE MUST BE MARKED TO INDICATE THAT. IDENTITY PART NO. (As shown on Label or package) PLASTI DIP SPRAY (ALL COLORS) IF APPLICABLE SECTION I MANUFACTURER'S EMERGENCY PHONE No. NAME Plasti Dip International Inc.
PAGE 2
SECTION VI - REACTIVITY AND STABILITY DATA STABILITY UNSTABLE STABLE X INCOMPATIBILITY (Materials to Avoid) Strong acids, bases, oxidizing agents, selected amines with alkali metals and halogens. HAZARDOUS DECOMPOSITION OR BY PRODUCTS Carbon Monoxide and/or Carbon Dioxide HAZARDOUS MAY OCCUR CONDITIONS TO AVOID Avoid contact with heat, sparks, and open flame. Product may explode if heated.