SDS

7. Handling and storage
Precautions for safe handling
Obtain special instructions before use. Do not handle until all safety precautions have been read
and understood. Pressurized container: Do not pierce or burn, even after use. Do not use if spray
button is missing or defective. Do not spray on a naked flame or any other incandescent material.
Do not smoke while using or until sprayed surface is thoroughly dry. Do not cut, weld, solder, drill,
grind, or expose containers to heat, flame, sparks, or other sources of ignition. All equipment used
when handling the product must be grounded. Do not re-use empty containers. Do not breathe
mist or vapor. Avoid contact with eyes, skin, and clothing. Avoid prolonged exposure. Do not taste
or swallow. When using, do not eat, drink or smoke. Pregnant or breastfeeding women must not
handle this product. Should be handled in closed systems, if possible. Use only in well-ventilated
areas. Wear appropriate personal protective equipment. Wash hands thoroughly after handling.
Avoid release to the environment. Observe good industrial hygiene practices.
Conditions for safe storage,
including any incompatibilities
Level 3 Aerosol.
Store locked up. Pressurized container. Protect from sunlight and do not expose to temperatures
exceeding 50°C/122 °F. Do not puncture, incinerate or crush. Do not handle or store near an open
flame, heat or other sources of ignition. This material can accumulate static charge which may
cause spark and become an ignition source. Secure cylinders in an upright position at all times,
close all valves when not in use. Store in a well-ventilated place. Store away from incompatible
materials (see Section 10 of the SDS).
8. Exposure controls/personal protection
Occupational exposure limits
US. OSHA Table Z-1 Limits for Air Contaminants (29 CFR 1910.1000)
ValueComponents Type
PEL 3.5 mg/m3Carbon Black (CAS
1333-86-4)
PEL 435 mg/m3ETHYLBENZENE (CAS
100-41-4)
100 ppm
PEL 2000 mg/m3HEPTANE (CAS 142-82-5)
500 ppm
PEL 590 mg/m3METHYL ETHYL KETONE
(CAS 78-93-3)
200 ppm
PEL 465 mg/m3METHYL N-AMYL KETONE
(CAS 110-43-0)
100 ppm
PEL 2900 mg/m3MINERAL SPIRITS (CAS
8052-41-3)
500 ppm
PEL 435 mg/m3Mixed Xylenes, Ethyl
Benzene (CAS 1330-20-7)
100 ppm
PEL 1800 mg/m3PROPANE (CAS 74-98-6)
1000 ppm
US. ACGIH Threshold Limit Values
ValueComponents
Form
Type
TWA 3 mg/m3 Inhalable fraction.Carbon Black (CAS
1333-86-4)
TWA 20 ppmETHYLBENZENE (CAS
100-41-4)
STEL 500 ppmHEPTANE (CAS 142-82-5)
TWA 400 ppm
STEL 300 ppmMETHYL ETHYL KETONE
(CAS 78-93-3)
TWA 200 ppm
TWA 50 ppmMETHYL N-AMYL KETONE
(CAS 110-43-0)
TWA 100 ppmMINERAL SPIRITS (CAS
8052-41-3)
STEL 150 ppmMixed Xylenes, Ethyl
Benzene (CAS 1330-20-7)
4 / 13
Material name: 11oz PLASTI DIP SPRAY BLACK - WS
05242 108258 604 Version #: 03 Revision date: 07-21-2015 Issue date: 07-15-2015
SDS US