SDS

ManualsBrandsPlasti Dip ManualsCraft Spray Paint1 gal. Glossifier

SAFETY DATA SHEET

1. Identification

Product identifier CLEAR GLOSS Plasti Dip TOPCOAT - WS

Other means of identification

Product Code

05242 109199 1G

Recommended use

Not available.

Manufacturer/Importer/Supplier/Distributor information

Manufacturer

Quest Industrial Products, LLC.

Address

N92 W14701 Anthony Avenue

Company name

Website

Telephone

Phone (262) 255-9500

Emergency phone number

Chemtrec Phone 800-424-9300

E-mail

United States

quest-ip.com

info@quest-ip.com

Menomonee Falls, WI 53051

2. Hazard(s) identification

Category 2Flammable liquids

Physical hazards

Category 4Acute toxicity, oral

Health hazards

Category 4Acute toxicity, inhalation

Category 2ASerious eye damage/eye irritation

Category 1BGerm cell mutagenicity

Category 1BCarcinogenicity

Category 1Specific target organ toxicity, repeated

exposure

Category 3Hazardous to the aquatic environment, acute

hazard

Environmental hazards

Category 3Hazardous to the aquatic environment,

long-term hazard

Not classified.

OSHA defined hazards

Label elements

Signal word

Danger

Hazard statement

Highly flammable liquid and vapor. Harmful if swallowed. Causes serious eye irritation. Harmful if

inhaled. May cause genetic defects. May cause cancer. Causes damage to organs through

prolonged or repeated exposure. Harmful to aquatic life. Harmful to aquatic life with long lasting

effects.

Precautionary statement

Prevention

Obtain special instructions before use. Do not handle until all safety precautions have been read

and understood. Keep away from heat/sparks/open flames/hot surfaces. - No smoking. Keep

container tightly closed. Ground/bond container and receiving equipment. Use explosion-proof

electrical/ventilating/lighting equipment. Use only non-sparking tools. Take precautionary

measures against static discharge. Do not breathe mist or vapor. Wash thoroughly after handling.

Do not eat, drink or smoke when using this product. Use only outdoors or in a well-ventilated area.

Avoid release to the environment. Wear protective gloves/protective clothing/eye protection/face

protection.

1 / 11

Material name: CLEAR GLOSS Plasti Dip TOPCOAT - WS

05242 109199 1G Version #: 03 Revision date: 07-21-2015 Issue date: 07-16-2015

SDS US

Summary of content (11 pages)

PAGE 1
SAFETY DATA SHEET 1. Identification Product identifier CLEAR GLOSS Plasti Dip TOPCOAT - WS Other means of identification Product Code 05242 109199 1G Recommended use Not available. Manufacturer/Importer/Supplier/Distributor information Manufacturer Company name Address Telephone Website E-mail Emergency phone number Quest Industrial Products, LLC. N92 W14701 Anthony Avenue Menomonee Falls, WI 53051 United States Phone (262) 255-9500 quest-ip.com info@quest-ip.com Chemtrec Phone 800-424-9300 2.
PAGE 2
Response If swallowed: Call a poison center/doctor if you feel unwell. If on skin (or hair): Take off immediately all contaminated clothing. Rinse skin with water/shower. If inhaled: Remove person to fresh air and keep comfortable for breathing. If in eyes: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. If exposed or concerned: Get medical advice/attention. Call a poison center/doctor if you feel unwell. Rinse mouth.
PAGE 3
Specific hazards arising from the chemical Special protective equipment and precautions for firefighters Vapors may form explosive mixtures with air. Vapors may travel considerable distance to a source of ignition and flash back. This product is a poor conductor of electricity and can become electrostatically charged. If sufficient charge is accumulated, ignition of flammable mixtures can occur. To reduce potential for static discharge, use proper bonding and grounding procedures.
PAGE 4
Conditions for safe storage, including any incompatibilities Store locked up. Keep away from heat, sparks and open flame. Prevent electrostatic charge build-up by using common bonding and grounding techniques. Eliminate sources of ignition. Avoid spark promoters. Ground/bond container and equipment. These alone may be insufficient to remove static electricity. Store in a cool, dry place out of direct sunlight. Store in original tightly closed container. Store in a well-ventilated place.
PAGE 5
Appropriate engineering controls Explosion-proof general and local exhaust ventilation. Good general ventilation (typically 10 air changes per hour) should be used. Ventilation rates should be matched to conditions. If applicable, use process enclosures, local exhaust ventilation, or other engineering controls to maintain airborne levels below recommended exposure limits. If exposure limits have not been established, maintain airborne levels to an acceptable level. Provide eyewash station.
PAGE 6
Specific gravity 0.79 VOC 696.072242 g/l Material 5.8090044 lbs/gal Material 5.8090088 lbs/gal Regulatory 696.072769 g/l Regulatory 10. Stability and reactivity Reactivity The product is stable and non-reactive under normal conditions of use, storage and transport. Chemical stability Material is stable under normal conditions. Possibility of hazardous reactions Hazardous polymerization does not occur. Conditions to avoid Avoid heat, sparks, open flames and other ignition sources.
PAGE 7
Components Oral LD50 Species Test Results Rat 6350 mg/l, 4 Hours Mouse 1590 mg/kg Rat 3523 - 8600 mg/kg * Estimates for product may be based on additional component data not shown. Prolonged skin contact may cause temporary irritation. Skin corrosion/irritation Causes serious eye irritation. Serious eye damage/eye irritation Respiratory or skin sensitization Not a respiratory sensitizer. Respiratory sensitization This product is not expected to cause skin sensitization.
PAGE 8
Other adverse effects No other adverse environmental effects (e.g. ozone depletion, photochemical ozone creation potential, endocrine disruption, global warming potential) are expected from this component. 13. Disposal considerations Disposal instructions Local disposal regulations Hazardous waste code Waste from residues / unused products Contaminated packaging Collect and reclaim or dispose in sealed containers at licensed waste disposal site.
PAGE 9
DOT IATA; IMDG 15. Regulatory information US federal regulations This product is a "Hazardous Chemical" as defined by the OSHA Hazard Communication Standard, 29 CFR 1910.1200. TSCA Section 12(b) Export Notification (40 CFR 707, Subpt. D) Not regulated. CERCLA Hazardous Substance List (40 CFR 302.4) METHYL ETHYL KETONE (CAS 78-93-3) Listed. Mixed Xylenes, Ethyl Benzene (CAS 1330-20-7) Listed. SARA 304 Emergency release notification Not regulated. OSHA Specifically Regulated Substances (29 CFR 1910.
PAGE 10
DEA Exempt Chemical Mixtures Code Number METHYL ETHYL KETONE (CAS 78-93-3) 6714 US state regulations US. California Controlled Substances. CA Department of Justice (California Health and Safety Code Section 11100) Not listed. US. California. Candidate Chemicals List. Safer Consumer Products Regulations (Cal. Code Regs, tit. 22, 69502.3, subd.
PAGE 11
NFPA ratings Health: 2 Flammability: 3 Instability: 0 Disclaimer The information in the sheet was written based on the best knowledge and experience currently available. THE INFORMATION CONTAINED HEREIN IS BASED ON DATA BELIEVED TO BE RELIABLE AND THE MANUFACTURER DISCLAIMS ANY LIABILITY INCURRED FROM THE USE OR RELIANCE UPON THE SAME.