Installation Instructions

ManualsBrandsPlatinum Tools ManualsAccessories4" Standard HPH J-Hook, Blue, Size 64, 25/Box

HPH Series J-Hook Installation Instructions

Summary of content (15 pages)

PAGE 1
HPH Series J-Hook Installation Instructions 1
PAGE 2
Mounting to a vertical surface: HPH16, HPH32, HPH48 and HPH64 Use a nail*, bolt* or screw* with a minimum head diameter of 0.329” (Fig.1-A) and an appropriate length for the substrate (Fig.1-B) to fasten the HPH J-Hook (Fig.2) to the vertical surface (Fig.3). Insert the cables and close the latch as shown in Fig.3. The latch must be in the closed position as shown in Fig.4 to secure the cables and complete the installation. Fig.1 Fig.2 Fig.3 Part No. HPH16 HPH32 HPH48 HPH64 Fig.
PAGE 3
Mounting to a rod or ceiling wire with a Multi-Function Clip-Batwing: HPH16W, HPH32W, HPH48W and HPH64W HPHXXW J-Hooks (Fig.1) are pre-assembled to Multi-Function Clip-Batwings at the factory using a fastener such as a rivet or a zinc plated ¼-20 x 3/8” pan head Phillips machine bolt and a grade A ¼-20 hex Nylon locknut (Fig.2). A plain HPH J-Hook may be assembled to a UL listed batwing clip in the field with the use of a similar fastener. Depress the batwing between your fingers (Fig. 3).
PAGE 4
Fig. 6 Fig. 7 Fig. 8 Part No. Hook Size HPH16W HPH32W HPH48W HPH64W 1" 2” 3” 4” Fig. No. 1 & 8 UL Load Rating LBS. | N 20 20 20 20 88.96 88.96 88.96 88.
PAGE 5
Mounting to a rod or a horizontal surface with an Angle Clip 90°: HPH16AC, HPH16AC6 HPH32AC, HPH32AC6, HPH48AC, HPH48AC6, HPH64AC & HPH64AC6 HPHXXAC and HPHXXAC6 J-Hooks (Fig.1 and Fig.2) are pre-assembled to Angle Clips 90° at the factory using a fastener such as a rivet or a zinc plated ¼-20 x 3/8” pan head Phillips machine bolt and a grade A ¼-20 hex Nylon locknut (Fig.3). A plain HPH J-Hook may be assembled to a Platinum Tools Angle Clip 90° in the field using a similar fastener.
PAGE 6
Fig. 6 Fig. 7 Fig. 8 Part No. HPH16AC HPH16AC6 HPH32AC HPH32AC6 HPH48AC HPH48AC6 HPH64AC HPH64AC6 Fig. 9 Hook Size 1" 1” 2” 2” 3” 3” 4” 4” Fig. No. 1 2 1 2 1 2 1 2 UL Load Rating LBS. | N 20 20 20 20 20 20 20 20 88.96 88.96 88.96 88.96 88.96 88.96 88.96 88.
PAGE 7
Mounting to a horizontal surface with an Angle Clip 90° w/Powder Actuated Nail (PAN): HPH16ACPA, HPH32ACPA, HPH48ACPA and HPH64ACPA Use a powder actuated tool* to install the 1-5/16” pin into an appropriate material such as concrete as shown in Fig. 3 & 4. Fig.1 Fig.2 Fig.3 Part No. HPH16ACPA HPH32ACPA HPH48ACPA HPH64ACPA Hook Size 1" 2” 3” 4” Fig. No. 1 & 2 Fig.4 Load Rating LBS. | N Description 20 20 20 20 1” 2” 3” 4” 88.96 88.96 88.96 88.
PAGE 8
Mounting to a beam with an HOK24 or HOK58 Hammer-On Beam Clamp: HPH16HOK24, HPH16HOK58, HPH32HOK24, HPH32HOK58, HPH48HOK24, HPH48HOK58, HPH64HOK24 and HPH64HOK58 Secure a Hammer-On Beam Clamp to a flange using a hammer as shown in Fig. 5 & Fig. 6 below. Note: The HOK-24 is designed for flanges from 1/8” to 1/4" thick; the HOK-58 is designed for flanges from 5/16” to 1/2" thick. Fig.1 Part No. HPH16HOK24 HPH16HOK58 HPH32HOK24 HPH32HOK58 HPH48HOK24 HPH48HOK58 HPH64HOK24 HPH64HOK58 Fig.
PAGE 9
Mounting to a beam with an FM24 or FM58 Hammer-On Beam Clamp: HPH16ACFM24, HPH16ACFM58, HPH32ACFM24, HPH32ACFM58, HPH48ACFM24, HPH48ACFM58, HPH64ACFM24 and HPH64ACFM58 Secure a knock-on beam clamp to a flange using a hammer as shown in Fig. 5 & Fig. 6 below. Note: The ACFM24 is designed for flanges from 1/8" to 1/4" thick. The ACFM58 is designed for flanges from 5/16" to 1/2" thick. Both the ACFM24 & ACFM58 can be rotated 360°. Fig.1 Part No. Fig.2 Hook Size Fig.3 Fig. No. UL Load Rating LBS.
PAGE 10
Mounting to a beam with a BC Beam Clamp: HPH16BC, HPH16ACBC, HPH32BC, HPH32ACBC, HPH48BC, HPH48ACBC, HPH64BC and HPH64ACBC Secure a screw-on beam clamp to a flange using a 3/8” socket driver or wrench as shown in Fig.5, 6, 7, & 8 below. Tighten the bolt to 20 in-lb. Note: The BC & ACBC’s are designed for flanges up to 1/2" thick. The ACBC can be rotated 360°. Fig.1 Part No. HPH16BC HPH16ACBC HPH32BC HPH32ACBC HPH48BC HPH48ACBC HPH64BC HPH64ACBC Fig.2 Hook Size 1" 1” 2” 2” 3” 3” 4” 4” Fig. No.
PAGE 11
Fig.7 Fig.8 Mounting to a beam with an SSBC Spring Steel Beam Clamp: HPH16SSBC, HPH16ACSSBC, HPH32SSBC, HPH32ACSSBC, HPH48SSBC, HPH48ACSSBC, HPH64SSBC and HPH64ACSSBC Secure a screw-on beam clamp to a flange using a 3/8” socket driver, wrench or Phillips head screw driver as shown in Fig. 5, 6, & 8 below. Tighten the bolt to 20 in-lb. Note: The SSBC & ACSSBC’s are designed for flanges up to 1/2" thick. The ACSSBC can be rotated 360°. Fig.1 Fig.2 Fig.3 Fig.
PAGE 12
Fig.5 Fig.6 Fig.7 Part No. Hoo k Size Fig.8 Fig. No. UL Load Rating LBS. | N HPH16SSBC 1" 1&2 20 88.96 HPH16ACSSBC 1” 3&4 20 88.96 HPH32SSBC 2” 1&2 17 75.62 HPH32ACSSBC 2” 3&4 20 88.96 HPH48SSBC 3” 1&2 20 88.96 HPH48ACSSBC 3” 3&4 20 88.96 HPH64SSBC 4” 1&2 17 75.62 HPH64ACSSBC 4” 3&4 20 88.
PAGE 13
Mounting to a joist with an Angled Overhang (AO) or Vertical Overhang (VO) spring steel clip: HPH16AO, HPH16VO, HPH32AO, HPH32VO, HPH48AO, HPH48VO, HPH64AO and HPH64VO Secure an AO spring steel “Z” purlin clip or a VO14 “C” purlin clip to a joist using a hammer as shown in Fig. 5, 6, 7, & 8 below. Note: The AO14 is designed for flanges 1/8” - 1/4" thick. Fig.1 Fig.2 Fig.5 Fig.3 Fig.4 Fig.
PAGE 14
Fig.7 Part No. Hook Size HPH16AO HPH16VO HPH32AO HPH32VO HPH48AO HPH48VO HPH64AO HPH64VO 1" 1” 2” 2” 3” 3” 4” 4” Fig. No. 1 3 1 3 1 3 1 3 & & & & & & & & Fig.8 UL Load Rating LBS. | N 2 4 2 4 2 4 2 4 20 20 17 17 20 20 17 17 88.96 88.96 75.62 75.62 88.96 88.96 75.62 75.
PAGE 15
Mounting to threaded rod with a female threaded eye coupling: HPH16EH, HPH32EH, HPH48EH and HPH64EH Thread the eye coupling on to ¼-20 threaded rod as shown in Fig. 3, 4 & 5 below. Fig.1 Fig.2 Fig.3 Part No. Hook Size HPH16EH HPH32EH HPH48EH HPH64EH 1" 2” 3” 4” Fig.4 Fig. No. 1 & 2 Fig.5 Load Rating LBS. | N Description 20 20 20 20 1” 2” 3” 4” 88.96 88.96 88.96 88.