YOURSELF Sy Featured Components (purchase separately): Featured Components (purchase separately): 7946 PS 7958 14 PS 8860 Pea PS 7676 PS 7690 PS 8814 Featured Components (purchase separately): Featured Components (purchase separate 7676 PS 7046 : PS 7946 : PSEUD PS 7676 PS 8813 PS 8313 i ' Call Toll Free 1-888-752-9782 PS 7720 We're Here To Help! .0 sodomize Monday Friday, 8:00 A M 10 5:00 PM.
SAFETY S &V &V VIV + This product is intended for single-family residential use only, by children ages two to ten and a maximum weight of 105 pounds. Any recommendation over 10 years of age or 105 pounds exceeds the upper limits specified in the American Society for Testing and Materials (MAST) Home Playground Safety Standard. In order for Play Star to comply with the MAST Standard, we cannot recommend anyone above these limits.
INSTALLATION: 1. Follow the instructions provided, do not alter its design in any way. 2. Place the play set on level ground, not less than 6' (1.8m) from any structure or obstruction such as a fence, garage, house, overhanging branches, laundry lines or electrical wires. If the area where you will be installing your play set is not level, you must make it level. 3. Play sets must be anchored to the ground. Follow the anchoring instructions provided with your building kit.
COMPONENTS INCLUDED = mfg} .’ 3 Corner swig & Brackets (18) Hangers Quick-Link Climbing Rocks (4 N Y4 Ring 4 Connectors Q\! Chain (8 Play set (12) ) Analogous > C‘fl Discovery © Monkey Telescope (1 cym Play Ring Handles Swing Seat (1 ngs Hanger (8) e QL Gym Ring Chains @ ‘ TOOLS REQUIRED Socket Wrench Drill Hack Saw Pencil Square The", 2" & %e" Socket Phillips Screwdriver ~ Saw Tape Punch Y1e" or Adjust.
Your building kit includes this template to help you create most of the hole patters needed to build your play set. Once the template is in position, mark only the holes that need to be drilled for each pattern. Remove 2"x6"x 10" 2"x6"x8 2"x4"x8 @ Lumber and Screw Requirements 2"x6"x 10" 2"x6"x8 2"x4"x8 Lumber and Ser requirement (25) 5/4" x 6" x (690) #8 x 215" Deck Screws (82) #8x 14" Deck Screws (20) 5/4" (605) #8 x 212" Deck Screws (82) #8x 14" Deck Screws the template before drilling.
ATTACHING CORNER BRACE There are several steps in the assembly of your play set when you will be asked to attach “corner brackets”. Please review these diagrams to understand where to place the brackets, how to attach them, and what hardware to use. The “corner bracket” has one long side and one short side.
CUTTING GUIDE GOLD Before starting to build your Play set, make sure all boards are cut and identified by size. Stack identical size boards in neat piles. (If you do not want to mark on dumber, use masking tape or chalk.) Shush will Improve your bulling time greatly because you will already know the size of each board as the instructions call for them.
ROOF ASSEMBLY GOLD Items for STEP 1: On a flat surface position boards together as shown. Position boards roof cap flush with outside edges. Use roof cap as a drill guide 41%" boards and drill %" holes 1" deep. (2) Roof Caps (12) #14 x 1¥4" pan head screws Keep boards square while attaching roof cap to boards with #14 x 1%4" pan head screws. Repeat for second assembly. B> 45, stems for STEP 2: Hold assemblies 50" apart. Position boards flush at the top and bottom as shown.
Items for STEP 4: (1) 2"x4"x 44" board (1) 2"x4"x42%" board (32) #8x 24" deck screws From the underside of roof assembly, place board flat against roof assembly centered as shown. Secure with two #8 x 214" deck screws per each roof board. Place 42\%" board flat against roof assembly and the board. Secure with #8 x 21" deck screws HOLE PATTERNS WORE ASSEMBLY GOLD stems for STEP 5. On a flat surface position boards at dimensions shown.
Items for STEP 6: On a flat surface position boards at dimensions shown. Keep assembly square (2) 2"x4"x 112" boards while securing with #8 x 24" deck screws. (1) 2"x6"x 47" boards boards @) 2"x4"x 372" boards (28) #8 x2'4" deck screws 100" 100428, SEE Page 6 For R Hole PATTERNS stems for STEP 7: 7) 2"x4"x56%" boards (42) #8 x 214" deck screws Position boards between assemblies as shown. Keep square while securing with #8 x 217" deck screws.
stems n for STEP 8: Roof Assembly 112" board %" x 5" hex bolts %" washers %" lock nuts #8 X 214" deck screws Secure these corners first Counter bore & Screw Placement Detail R NN Position roof assembly so both sides of roof overhang 2" x 4" boards equally. Secure top corners with two #8 x 214" deck screws, %" x 5" hex bolt, %" washers and 32" lock nuts. If lumber is oversize, counter boring may be required. Drill 174" counter bore 4" deep.
Items for STEP 10: (8) Corner Brackets (8) %" x 314" hex bolts hex bolts (16) 3" washers (16) %" lock nuts (32) #8x 114" deck screws Lift tower assembly upright and position in desired location. Caution: Make sure tower remains square. Ground must be level. Installation on a hill or incline will create unsafe conditions. Position brackets so that the long sides are against the 562" boards. Use the bracket as a drill guide and drill 14" holes 1" deep into the boards. Attach with #8 x 14" deck screws.
stems for STEP 11: @) boards (8) #8x 2" deck screws Position boards at the dimensions shown. Secure with #8 x 214" deck screws. level iz boards gap. SEE Pace 6 For HOLE PATTERNS stems for STEP 12: (10) 5/4" boards (80) #8x2'2" deck screws E Position outside boards tight against the boards and equally space remaining boards as shown. Secure with #8 x 214" deck screws. {10} Caution: Gap between boards must be smaller than V4" or forger than V2" or a finger entrapment could exist.
stems for STEP 13: @) 2"x4"x 312" boards / @) 2"x4"x10%" boards " (32) #8x 214" deck screws Zx4Tx 10" () Position boards at dimensions shown. Secure with #8 x 24" deck screws. 8En" 8o SEE Page 6 For R Hole PATTERNS stems for STEP 14: (1) 2"x4"x 41" board (2) 2"x4"x 19%" boards (12) #8x 22" deck screws Position boards at dimensions shown Secure with #8 x 214" deck screws.
Items for STEP boards (32) #8x 2V%" deck screws Position end boards flush with 2" x 4" boards. Space remaining boards as shown. Secure with #8 x 22" deck screws. Caution: Gap between boards must be smaller than 4" or forger than 2" or a finger entrapment could exist. 2" x4 x4 Flush 4 x 6 x44" (4) SEE Page 6 For R Hole PATTERNS E Items for STEP 16: (1) 2"x4"x 81" board (3) 2"x4"x 47" boards (2) 2"x4"x 31%" boards (28) #8 x 212" deck screws Position boards at dimensions shown.
stems for STEP 17: (10) boards (40) #8x 2V2" deck screws Position seven boards on the inside and three on the outside of the tower flush with the top and bottom guardrail boards and equally spaced. Secure with #8 x 21" deck screws. Caution: Gap between boards must not exceed 3'2" or a head entrapment could exist.
stems for STEP boards boards boards (1) 2"x4"x 18" board (28) #8 x 214" deck screws Position %" x 6" boards on the inside of the tower flush with the top and bottom guardrail boards and equally spaced as shown. Secure with #8 x 212" deck screws. Attach board centered In the window and flush with boards as shown. Secure with #8 x 214" deck screws.
CUTTING GUIDE SILVER Before starting to build your Play set, make sure all boards are cut and identified by size. Stack identical size boards in neat piles. (If you do not want to mark on lumber, use masking tape or chalk.) Shush will improve your bulling time greatly because you will already know the size of each board as the instructions call for them.
ROOF ASSEMBLY SILVER Items for STEP 1: On a flat surface position boards together as shown. Position boards roof cap flush with outside edges. Use roof cap as a drill guide 41%" boards and drill %" holes 1" deep. (2) Roof Caps (12) #14 x 1¥4" pan head screws Keep boards square while attaching roof cap to boards with #14 x 1%4" pan head screws. Repeat for second assembly. 45, B> stems for STEP 2: Hold assemblies 50" apart. Position boards flush at the top and bottom as shown.
Items for STEP 4: (1) 2"x4"x 44" board (1) 2"x4"x42%" board (32) #8x 24" deck screws From the underside of roof assembly, place board flat against roof assembly centered as shown. Secure with two #8 x 212" deck screws per each roof board Place 42\%" board flat against roof assembly and the board. Secure with #8 x 21" deck screws HOLE PATTERNS WORE ASSEMBLY SILVER stems for STEP 5: On a flat surface position boards at dimensions shown.
Items for STEP 6: On a flat surface position boards at dimensions shown. Keep assembly square @ 2'x4"x 100" boards while securing with #8 x 2" deck screws. (1) 2"x6"x 47" boards 2) 2"x4"x 47" boards 101" @) 2"x4"x 37'%" boards (28) #8 x 214" deck screws 26" 10140 SEE Page 6 For R Hole PATTERNS stems for STEP 7: 7) 2"x4"x56%" boards (42) #8x 24" deck screws Position boards between assemblies as shown. Keep square while securing with #8 x 21" deck screws.
Items for STEP §: Position roof assembly so both sides of roof overhang 2" x 4" boards equally. Secure (1) Roof Assembly top corners with two #8 x 214" deck screws, %" x 5" hex bolt, %" washers and 32" lock (1) 2"x4"x 100" board nuts. If lumber is oversize, counter boring may be required. Drill 174" counter bore hex bolts 4" deep. (See Counter bore & Screw Placement Detail below) (4) 3" washers (2) %" lock nuts Secure these (17) #8x 2'2" deck screws corners first Attach 100" at dimension shown.
stems for STEP 10: (8) Corner Brackets (8) %" x 314" hex bolts hex bolts (16) 3" washers (16) %" lock nuts (32) #8x 114" deck screws Lift tower assembly upright and position in desired location. Caution: Make sure tower remains square. Ground must be level. Installation on a hill or incline will create unsafe conditions. Position brackets so that the long sides are against the 562" boards. Use the bracket as a drill guide and drill 14" holes 1" deep into the boards. Attach with #8 x 14" deck screws.
Items for STEP 561" boards (8) #8x 2" deck screws Position boards at the dimensions shown. Secure with #8 x 214" deck screws SEE Page 6 For R Hole PATTERNS stems for STEP 12: (10) boards (80) #8 x 214" deck screws Position outside boards tight against the boards and equally space remaining boards as shown. Secure with #8 x 21" deck screws (10) 2'x 68'x 47" Caution: Gap between boards must be smaller than V4" or forger than V2" or a finger entrapment could exist.
stems for STEP 13: @) 2"x4"x 312" boards 4) 2"x4"x10%" boards (32) #8x 214" deck screws 100" (4) Position boards at dimensions shown. Secure with #8 x 24" deck screws. 7314 73V 547" SEE Page 6 For R Hole PATTERNS stems for STEP 14: (1) 2"x4"x 41" board @) 2"x4"x 19%" boards (12) #8x 214" deck screws Position boards at dimensions shown. Secure with #8 x 212" deck screws.
stems for STEP boards (32) #8x 2V%" deck screws Position end boards flush with 2" x 4" boards. Space remaining boards as shown. Secure with #8 x 22" deck screws. Caution: Gap between boards must be smaller than 4" or forger than 2" or a finger entrapment could exist. Flush Flush SEE Page 6 For R Hole PATTERNS Items for STEP 16: (1) 2"x4"x 81" board 2) 2"x4"x 47" boards @) 2"x4"x 312" boards (24) #8x 214" deck screws Position boards at dimensions shown. Secure with #8 x 21" deck S Crews.
stems for STEP boards (20) #8x 2V2" deck screws ¥ Position two boards on the inside and three boards on the outside of the tower flush with the top and bottom guardrail boards and equally spaced as shown. Secure with #8 x 214" deck screws Pattern [ Caution: Gap between boards must not exceed 3'2" or a head entrapment could exist.
stems for STEP boards boards boards (1) 2"x4"x 18" board (28) #8 x 24" deck screws Position %" x 6" boards on the inside of the tower flush with the top and bottom guardrail boards and equally spaced as shown. Secure with #8 x 212" deck screws. Attach board centered in the window and flush with boards as shown. Secure with #8 x 214" deck screws. 2"x4"x 18" Hush . . le Caution: Gap between boards must be smaller than V4" or forger than %" or a finger entrapment e e View from inside could exist.
CUTTING GUIDE BRONZE Before starting to build your Playhouse, make sure all boards are cut and identified by size. Stack identical size boards in neat piles. (If you do not want to mark on lumber, use masking tape or chalk.) Shush will improve your bulling time greatly because you will already know the size of each board as the instructions call for them.
ROOF ASSEMBLY BRONZE stems for STEP 1: (2) 2"x4"x 34" boards 2"x4"x 30%" boards (2) Roof Caps (12) #14 x 1V4" pan head screws B> On a flat surface position boards together as shown. Position roof cap flush with outside edges. Use roof cap as a dell guide and drill 4" holes 1" deep. Keep boards square while attaching roof cap to boards with #14 x 1%4" pan head screws. Repeat for second assembly. Items for STEP 2: Hold assemblies 50" apart. Position boards flush at the top and bottom as shown.
Items for STEP 4: (1) 2"x4"x 33%" board (1) 2"x4"x 32" board (24) #8x 2V%" deck screws From the underside of roof assembly, place 334" board flat against roof assembly centered as shown. Secure with two #8 x 214" deck screws per each root board. Place board flat against roof assembly and the 33'2" board. Secure with #8 x 214" deck screws 331&" WORE ASSEMBLY BRONZE stems for STEP 5: On a flat surface position boards at dimensions shown.
Items for STEP 6: On a flat surface position boards at dimensions shown. Keep assembly square @ 2'x4"x 100" boards while securing with #8 x 2" deck screws. (1) 2"x6"x 47" boards 2) 2"x4"x 47" boards 101" @) 2"x4"x 37'%" boards (28) #8 x 214" deck screws 26" 10140 SEE Page 6 For R Hole PATTERNS stems for STEP 7: 7) 2"x4"x45%" boards (42) #8x 24" deck screws Position boards between assemblies as shown. Keep square while securing with #8 x 212" deck screws.
Items for STEP §: Position roof assembly so both sides of roof overhang 2" x 4" boards equally. Secure (1) Roof Assembly top corners with two #8 x 214" deck screws, 3" x 5" hex bolt, 3" washers and %" lock (2) %"x 5" hex bolts nuts. If lumber is oversize, counter boring may be required. Drill 174" counter bore @) %" washers 14" deep. (See Counter bore & Screw Placement Detail below) (2) %" lock nuts (4) #8x 24" deck screws Secure these corners first Counter bore & Screw Placement Detail I Prevail 15" Dia.
Items for STEP 10: Lift tower assembly upright and position in desired location. (8) Corner Brackets hex bolts Caution: Make sure tower remains square. Ground must be level. hex bolts Installation on a hill or incline will create unsafe conditions. (16) 3" washers X (16) %" lock nuts (32) #8x 114" deck screws Position brackets so that the long sides are against the 451%" boards. Use the bracket as a drill guide and drill 1" holes 1" deep into the boards. Attach with #8 x 174" deck screws.
(64) #8x 2V2" deck screws E stems for STEP 12: / (8) 5/4"x 6" x 44" boards . Position outside boards tight against the boards and equally space remaining boards as shown. / Secure with #8 x 214" deck screws Caution: Gap between boards must be smaller than 4" or forger than 2" or a finger entrapment could exist. SEE Pace 6 For Hole PATTERNS stems for STEP 13: @) 2"x4"x 454" boards (4) 2"x4"x 10'%" boards (32) #8x 2V2" deck screws 2"x 4" x 10v2" Position boards at dimensions shown. Secure with #8 x 24" deck.
stems for STEP 14: (1) 2"x4"x 41" board @) 2"x4"x25%" boards (12) #8x 2'%" deck screws Position boards at dimensions shown. Secure with #8 x 212" deck screws. 2"x 4" x 41", 2516 16%2" from outside to center of board 162" from outside to Bt center of HOLE PATTERNS board Items for STEP boards (40) #8x 2V2" deck screws Position end boards flush with 2" x 4" boards. Space remaining boards as shown.
stems for STEP 16: (1) 2"x4"x 81" board @) 2"x4"x 47" boards (3) 2"x4"x20%" boards (30) #8x 214" deck screws 201" Position boards at dimensions shown. Secure with #8 x 21" deck S Crews. 931" 80" 73V SEE Page 6 For R Hole PATTERNS stems for STEP boards (32) #8x 24" deck screws Position two boards on the inside and six boards on the outside of the tower flush with the top and bottom guardrail boards and equally spaced as shown.
stems for STEP boards boards boards board (42) #8x 24" deck screws Position %" x 6" boards on the inside of the tower flush with the top and bottom guardrail boards and equally spaced. Secure with #8 x 212" deck screws. Caution: Gap between boards must be smaller than 4" or larger than %" or a finger entrapment could exist. Rush with decking View from inside SEE Pace 6 For HOLE PATTERNS Items for STEP 20: (1) 2"x4"x 28" boards (6) #8x 214" deck screws ‘BL‘1 W Position board at the dimensions shown.
CUTTING GUIDE STARTER Before starting to build your Play set, make sure all boards are cut and identified by size. Stack identical size boards in neat piles. (If you do not want to mark on lumber, use masking tape or chalk ) Shush will improve your bulling time greatly because you will already know the size of each board as the instructions call for them.
ROOF ASSEMBLY Starter stems for STEP 1: (2) 2"x4"x 34" boards 2"x4"x 30%" boards (2) Roof Caps (12) #14 x 1V4" pan head screws B> On a flat surface position boards together as shown. Position roof cap flush with outside edges. Use roof cap as a dell guide and drill 4" holes 1" deep. Keep boards square while attaching roof cap to boards with #14 x 1%4" pan head screws. Repeat for second assembly. Items for STEP 2: Hold assemblies 50" apart. Position boards flush at the top and bottom as shown.
Items for STEP 4: (1) 2"x4"x 33%" board (1) 2"x4"x 32" board (24) #8x 2V%" deck screws From the underside of roof assembly, place 334" board flat against roof assembly centered as shown. Secure with two #8 x 214" deck screws per each root board. Place board flat against roof assembly and the 33'2" board. Secure with #8 x 214" deck screws 331&" SeE Pace 6 FOR WORE ASSEMBLY Starter stems for STEP 5: On a flat surface position boards at dimensions shown.
Items for STEP 6: On a flat surface position boards at dimensions shown. Keep assembly square @ 2'x4"x 100" boards while securing with #8 x 2" deck screws. (1) 2"x6"x 47" boards 2) 2"x4"x 47" boards 101" @) 2"x4"x 37'%" boards (28) #8 x 214" deck screws 10140 SEE Page 6 For R Hole PATTERNS stems for STEP 7: 7) 2"x4"x45%" boards (42) #8x 24" deck screws Position boards between assemblies as shown. Keep square while securing with #8 x 212" deck screws.
stems for STEP §: (1) Roof Assembly hex bolts (4) %" washers (2) %" lock nuts (4) #8x 24" deck screws Counter bore & Screw Placement Detail I Prevail 15" Dia. Jor #8 X 272" deck screws " Dia. Jor %" X 5" hex bolts Position roof assembly so both sides of roof overhang 2" x 4" boards equally. Secure top corners with two #8 x 214" deck screws, %" x 5" hex bolt, %" washers and 32" lock nuts. If lumber is oversize, counter boring may be required. Drill 174" counter bore 4" deep.
stems for STEP (16) (16) (32 Position brackets so that the long sides are against the 451" boards. Use the bracket as a drill guide and drill 1" holes 1" deep into the boards. Attach with #8 x 174" deck screws. Use bracket as a drill guide and dill %' holes completely through the boards. Secure with %" hex bolts (2" through one board and 32" through two boards), %" washers and %" lock nuts.
stems for STEP 12: (8) 5/4"x 6" x 44" boards (64) #8x 2V2" deck screws Position outside boards tight against the boards and equally space remaining boards as shown. Secure with #8 x 214" deck screws Caution: Gap between boards must be smaller than 4" or forger than 2" or a finger entrapment could exist. SEE PAGE 6 For HOLE PATTERNS Items for STEP 451" boards 4) 2"x4"x10%" boards (32) #8x 24" deck screws 2"x 4" x 101" Position boards at dimensions shown. Secure with #8 x 214" deck screws.
Items for STEP 14: (1) 2"x4"x 81" board 2) 2"x4"x 47" boards (3) 2"x4"x20%" boards (30) #8 x 214" deck screws 2008 Position boards at dimensions shown. Secure with #8 x 214" deck screws. 730 SEE PAGE 6 For HOLE PATTERNS Items for STEP 15: (13) boards (52) #8x 214" deck screws Position seven boards on the inside and six boards on the outside of the tower flush with the top and bottom guardrail boards and equally spaced as shown. Secure with #8 x 2V2" deck screws.
Items for STEP 16: (1) 2"x4"x28%" board (6) #8x 24" deck screws Position 28'4" board on the inside of the tower at the dimensions shown Secure with #8 x 21" deck screws SeE Pace 6 For [Ny gy Items for STEP board (6) #8x 212" deck screws Position end board flush with board. Secure with #8 x 214" deck screws.
wing Beam Assembly Items for STEP boards (54) #8 x 212" deck screws 12t ogn Mark & Drill 3 Boards as shown Assemble swing posts (3 required). B Place one drilled board on top of a non-drilled board. Make sure boards are flush with each other. If one board is longer than the other, flush one end and SeE Pace 6 For let the other end hang over. Secure with #8 x 214" deck Hole PATTERNS screws. Note: Repeat two more times for the second and third swing post assemblies.
Items for STEP 2: (3) Sturdy-Frame Brackets hex bolts (12) %" washers (6) %" lock nuts (6) #8x 14" deck screws Attach one right-hand (R) and two left-hand (L)} sturdy-frame brackets onto separate swing post assemblies (brackets are stamped R and L). Lay bracket on the flush end of post as shown. Slide bracket over and down until it stops against the top and side of the post as shown. When correctly positioned, the edge of the sturdy-frame bracket will be parallel with the side of the post.
Items for STEP hex bolts (2) %" lock nuts Mate the left-hand bracket assembly with the flipped bolt to one right-hand bracket assembly as shown. Secure with two 35" X %" hex bolts and %" lock nuts through the two lower holes of brackets as shown (do not use flat washers). Sipped Bolt Items for STEP hex bolts (2) %" lock nuts Place two 3" x %4" hex bolts and %" lock nuts through the two lower holes of bracket on single post as shown (do not use flat washers).
Items for STEP 5: (1) 2"x4"x 60" board (4) #8x 214" deck screws Position assembly as shown. Align the posts so that the outermost points measure 92%4" as shown. Attach board at dimension shown. Secure with #8 x 2'4" deck screws. Note: Brackets / are facing down.
stems for STEP 6: (2) comer brackets (8) #8x 1V4" screws (2) %" x 3%2" hex bolts hex bolts (4) %" washers (4) %" lock nuts Attach corner brackets. To complete the A-Frame Assembly, flip over as shown and position brackets so that the short side is against the board. Use the bracket as a drill guide and drill 15" holes 1" deep into the board. Attach with #8 x 14" deck screws. Again use the bracket as a drill guide and drill %" holes completely through the boards.
Items for STEP 120" board (4) #8 x 1V4" deck screws Lay out the single post assembly and the A-Frame assembly approximately 90" apart. Use remaining unused boards to elevate approximately 3". Place 120" board under brackets as shown. Hold beam tight against bracket. Beam should rest hex bolts and top of post when in proper position. Be sure A-Frame is square (90°) with beam.
Items for STEP 120" board (10) #8x 22" deck screws Espadrille the 120" beam board at the dimension shown. Attach the drilled 120" board on top of the existing assembly as shown. Make sure boards are flush with bottom board. Secure boards together with #8 x 212" screws. Note: If your boards are a different length, flush the end with the single post.
Items for STEP hex bolts (10) %" washers (5) %" lock nuts Lift swing beam assembly and support with saw horses. Note: If you do not have saw horses, rest beam on ground and rotate A-frame and single post simultaneously to the other side (requires two adults). Single post must be supported to keep the bracket from bending. Complete and rotate back to original position. From the bottom side of beam, use the six 32" holes in bottom board as a drill guide and drill %" holes back through both boards.
Items for STEP 10: Mark the top beam board, on the bottom edge, at the dimensions shown, for swing hanger locations. (6) swing hangers lag screws NOTE: If you are installing the Air Rider, follow the installation (6) %" washers instructions that are supplied with the Air Rider. Drill a ¥4" hole 214" deep in the center of the bottom board at each swing hanger location. Screw swing hangers into beam by hand (a long screwdriver will help).
STUD MARE BRACE INSTALLATION rems for Step 11: (1) Sturdy-Frame Brace (1) 4" hex bolt (2) 3" washers (1) 3" lock nut @ Remove the nut and washer from the flipped bolt as shown. (Fig. 1} Install the Sturdy-Frame Brace as shown and secure with 3" washer and lock nut. (Fig. 1) Make sure brace is square to beam. Using the brace as a template, drill a %" hole completely through beam. (Fig. 2) Secure the Sturdy-Frame Brace to the beam with the %" x 4" hex bolt, washers and lock nut.
Items for STEP 13: (2) comer brackets (2) #8x 212" deck screws (8) #8 x 1V4" deck screws hex bolt hex bolts (4) %" washers (4) %" lock nuts Front View Attach board to swing beam post. Secure using #8 x 212" deck S Crews. Position brackets so that the short sides are against the board. Use the bracket as a drill guide and drill 4" holes 1" deep into the board. Attach with #8 x 114" deck screws. Again use the bracket as a drill guide and drill %" holes completely through the boards.
Monkey Ring Assembly totems for STEP 1: Beam Assemblies Drill Pattern Y on each end board as shown. (2) 2"x4"x72"boards (2) 2"x4"x 69" board Position board centered on top (24) #8x 24" deck screws board as shown. Secure with #8 x 212" deck screws. Repeat for second assembly. x4"x72" o7 SEE Pace 6 For Hole PATTERNS Items for STEP 2: Using a U-strap as a drill guide. Drill two %" holes 1" deep at dimensions @) U-straps shown install chains to U-straps. Secure with 4" x 112" lag screws.
Items for STEP 3: Base Assembly: On a flat surface position boards at dimensions shown. Keep (2) 2"x4"x 96" boards assembly square while securing with #8 x 212" deck screws. (3) 2"x4"x 281" boards (18) #8x 24" deck screws SEE Page 6 For R Hole PATTERNS Items for STEP 4: Flip assembly over and position board at dimension shown. 2812" board Secure with #8 x 212" deck screws.
Items for STEP 5: (2) Beam Assemblies from Step deck screws Attach beam assemblies to the frame on the opposite end to the 48" dimension as shown. Secure with #8 x 212" deck Screws. SEE Page 6 For R Hole PATTERNS Items for STEP 6: (2) Corner Brackets (4) %" x 314" hex bolts (4) %" washers 4) %" lock nuts (8) #8x 1'4" deck screws Position brackets so that the long sides are against the boards. Use brackets as a drill guide and drill %" holes 1" deep into the boards. Attach with #8 x 1V4" deck screws.
Items for STEP 7; (1) Monkey Ring Base & Beam Assembly (4) #8x 215" deck screws Lift the base and beam assembly into an upright position at the 98" dimension shown. Secure with #8 x 212" deck screws. SEE PAGE 6 For R Starter Tower Shown Hole PATTERNS stems for STEP 8: (2) Comer Brackets (4) %" x 3%%" hex bolts (4) %" washers (4) %" lock nuts (8) #8x 1¥" deck screws Position brackets so that the long sides are against the boards. < Use brackets as a drill guide and drill holes 1" deep into the boards.
Items for STEP Corner Brackets boards %" x 2" hex bolts %" washers %" lock nuts #8 x 14" deck screws #8 x 214" deck screws Position brackets 42" up from bottom of tower with the long side of the brackets against the boards and the short side flush with the inside edges as shown. Use brackets as a drill guide and drill %" holes 1" deep into the boards. Attach with #8 x 174" deck screws. Again use brackets as a drill guide and drill %" holes completely through the boards.
Items for STEP 10: (9) %" x6"x 21%" boards (36) #8x 2" deck screws 211" (9) Pattern I SeE Pace 6 FOR Ho Lee Pat Terns Position first 212" board tight at the top as shown. Secure with #8 x 214" deck screws. Position next 211" board tight against first board. Secure with #8 x 212" deck screws. Repeat for remaining boards. Hole placement for Climbing Rope: Drill a %4 hole in center of boards shown. Install rope per instructions on Page 75.
At locations shown screw Play set Anchors into ground by hand (a long screwdriver will help). Use the anchor as a drill guide and drill a ¥4" hole 212" deep into the board. Attach with %" x 3" lag screw and %" washer. When anchoring at tower locations, back out existing %" x 3" lag screw with washer. Screw anchor into ground until loop in anchor lines up with hole in tower. Re-install lag screw with washer to secure anchor.
SLIDE Mounting Instructions 1. Align slide at right angle (90°) to 48" play deck. Lip of slide should rest on the play deck Using the slide as a template, mark play deck through the three holes In the slide. Drill three %" holes at marked location. 2. Attach slide temporarily to play deck with three #14 x screws provided. 3. Prepare level area where slide touches ground that is 1" below surrounding grade. 4. Locate and mark the ground on the back side, on either side of the star.
CLIMBING STEPS Assembly Instructions £, 1. Place the let (L) step side rail on a fiat work surface. Insert one top step into the top hole. Note: This hole does not go completely through the side rail. 2. Insert three 231" standard steps into the remaining holes until they are flush with the outside of the side rail. (Fig. 1} 3. Insert the right (R) step side rail on top of the existing boards until the standard boards are flush with the outside of the side rail. (Fig. 2} 4.
CLIMBING WALL Mounting Instructions Align top of Climbing Wall at right angle 90°). Lip of climbing wall should rest on the play deck Using the Climbing Wall as a template, mark play deck through the three holes in the climbing wall. Drill three %" holes at marked locations. (Fig. 1} Attach Climbing Wall temporarily to play deck with three #14 x 174" pan head screws provided. Prepare level area where Climbing Wall touches ground. Locate and mark the ground on the back side and in center of Climbing Wall.
COMPONENTS Mounting Instructions SWING SEAT + GYM RINGS 1. Attach coated ends of chains onto play component using Quick-Link Connectors provided. Tighten securely with an adjustable wrench. 2. Hook undercoated ends of chain onto Swing Hangers provided. @ 3. Customize the height of your swing or gym rings anywhere n the Adjustment Zone, to fit your child. Swing Chain Spain 10" minimum spacing s quavered from the closest point of all Warning: Failure to tighten Quick Links objects.
You for choosing Play Star. Because it is our intention to make this a positive family experience, we hive taken great care in preparing this product. Should you have any questions, o if we can assist you in ay way, please call our friendly Customer Service Department for immediate action. Do not return to the store, Please call us Toll Free at 1-888-PLAY STAR (752-9782) Monday through Friday, 8:00 AM. 10 5:00 PM. C.S.T. Ask for Customer Service.