Technical Specifications

T
he Climbing Steps can be mounted
o
n 48" or 60" play decks.
Please follow the appropriate directions below:
1. Place the left (L) step side rail on a flat
work surface. Insert one 2" x 6" x 21"
top step into the top hole.
Note: This hole does not go
completely through the side rail.
Insert three 2" x 6" x 23¹⁄₂" standard steps
into the remaining holes until they are flush with
the outside of the side rail. (Fig. 1)
2. Insert the right (R) step side rail
on top of the existing boards until
the standard boards are flush with
the outside of the side rail. (Fig. 2)
3. Install the Climbing Steps Assembly to
your tower: Position the Climbing Steps
Assembly into the 21¹⁄₂" opening of
your play deck so that the top surface
of the top step is flush with the top
surface of the play deck. Push side rails
of Climbing Step Assembly forward
until they contact the play deck.
Note: The steps must be positioned
as specified, otherwise a head
entrapment or tripping hazard
could exist. Secure the Climbing Step
Assembly to the play deck using three #14 x 1¹⁄₄" pan head screws on
each side as shown. (Fig. 3)
4. Make sure that all the standard
steps are flush with the outside
sides of the Climbing Steps
Assembly. Secure each step
to the side rails using two
#14 x 1¹⁄₄" pan head screws for
each step as shown. (Fig. 4)
MOUNTING INSTRUCTIONS
Tools Required: Drill, ¹⁄₈" Drill Bit, Tape Measure, Saw, Square,
Rubber Mallet, Phillips Screwdriver, Safety Glasses
Materials Required: (1) 2" x 6" x 8'
H
ardware Included
:
Cutting Guide:
2" x 6" x 8' – one (1) board required
Top Std. Std. Std.
Step Step Step Step
48" PLAY DECK
Fig. 2
Fig. 1
Fig. 4
3. Install the Climbing Steps Assembly
to your tower. Position the Climbing
Steps Assembly into the 21¹⁄₂" open-
ing of your play deck so that the top
surface of the top step is 12" from
the top surface of your play deck (48"
from the ground). Secure the Climbing
Step Assembly to the play deck using
three #14 x 1¹⁄₄" pan head screws on
each side as shown. (Fig. 3)
Tools Required
: Drill, ¹⁄₈" Drill Bit, Tape Measure, Saw, Square,
Rubber Mallet, Phillips Screwdriver, Safety Glasses
Materials Required
:
(1) 2" x 6" x 8' (1) 2" x 4" x 28¹⁄₂" (8) #8x2¹⁄₂" Deck Screws
Hardware Included:
Cutting Guide:
Fig. 4
Fig. 2
Fig. 1
60" PLAY DECK
2" x 6" x 8' – one (1) board required
Top Step 3 Standard Steps
2" x 4" x 8' – one (1) board required
Filler Board
MOUNTING INSTRUCTIONS
5. Install one 2" x 4" x 28¹⁄₂" filler
board an equal distance between
the top of the step and the bottom of the
deck supports. The gaps left should be
approximately 1³⁄₄".
NOTE: The steps must be positioned
as specified. The gaps must not
exceed 3¹⁄₂" otherwise a head entrap-
ment could exist.
Secure with eight #8 x 2¹⁄₂" deck screws.
(Fig. 5)
Fig. 5
4. Make sure that all standard steps
are flush with the outside sides of
the Climbing Steps Assembly. Secure
each step to the side rails using two
#14 x 1¹⁄₄" pan head screws for
each step as shown. (Fig. 4)
1. Place the left (L) step side rail on a
flat work surface. Insert one 2" x 6"
x 21" top step into the top hole.
Note: This hole does not go
completely through the side rail.
Insert three 2" x 6" x 23¹⁄₂"
standard steps into the
remaining holes until
they are flush
with the outside
of the side rail.
(Fig. 1)
2. Insert the right (R) step side
rail on top of the existing
boards until the standard
boards are flush with the
outside of the side rail. (Fig. 2 )
21" 23¹⁄₂" 23¹⁄₂" 23¹⁄₂"
21" 23¹⁄₂" 23¹⁄₂" 23¹⁄₂"
28¹⁄₂"
(20) #14 x 1¹₄" Pan Head Screws
Depending on your application,
some hardware may not be used.
(20) #14 x 1¹₄" Pan Head Screws
Depending on your application,
some hardware may not be used.
12"
Fig. 3
Fig. 3